Search Documents

By J Nemcik, E Baafi, I Porter, G Spinks

Spray-on liners used in the mining industry for ground support and stabilisation applications are either cement based (æshotcreteÆ) or polymer based (æthin spray-on linersÆ). Some thin spray-on liners are a blend of both polymer and cement (eg Tekflex). A small number of thin spray-on liners (TSLs) have been trialled in Australia as potential replacements for steel mesh in roadways and other underground mining applications; however, they were found to cure slowly and the cured coatings became brittle after an extended time in place. The University of Wollongong in collaboration with the Australian coal mining industry has shown that a viable polymer-based alternative to steel mesh in underground roadway support applications can be developed to eliminate the use and handling of steel mesh. The work to date has: established the feasibility of developing polymeric alternatives to steel mesh in underground roadway support applications; identified the physical and material constraints to be endured by any new polymeric skin reinforcement system by measuring the mechanical properties of steel mesh; identified materials that can be spray applied; and demonstrated that polymer mechanical properties can be optimised to produce similar mechanical properties (elastic modulus, yield stress, elongation-at-break, etc) to steel mesh. The identified materials will: allow the face support cycle to be fully automated, or at least remotely operated and installed; remove personnel from the immediate face area; and substantially improve underground roadway development rates.

Jan 1, 2008

By M L. Habner, S D. Munro

In a gold CIP/CIL circuit, adding new circuit water to a final tails thickener and then directing the thickener overflow to the head of the circuit significantly reduces the cyanide concentration at the TSF discharge spigot. The new water is used to dilute the final tails. The dilution and recycle of the tails in this manner may have the added benefit of reducing reagent consumption, in some cases to the point where the reagent savings justify the expenditure and Cyanide Code compliance is achieved at no extra cost. Potential circuit configurations and water recycles can be modelled by splicing a flowsheeting and thermodynamics package, such that changes to the composition of the water can be reduced to chemical speciation with a Gibbs free energy minimisation enabling a complete understanding of the circuit water chemistry.

Jan 1, 2007

The use of rubber-tyred equipment in a decline mining system requires that roadways be kept free of running water. At Renison this is achieved by the use of stage pumping or gravitating to a major pump station and pumping from there directly to the surface. The frequent use of pick-up lines and pump boxes in the decline system provides a method of water control and reduces the amount of slimes in pump lines. The Bassett Fault structure, which lies on the hangingwall of the mine is the major source of ground water. This is encountered in diamond drill holes and exploration develop- ment. Dewatering of this structure is possible by controlling the flow from selected holes. Future pumping requirements may be predicted by analysing changes in the level of the water table and by calculating dewatering rates required to maintain ore reserves available for production.

Jan 1, 1977

By M Robotham

In April 2013, Rio Tinto Kennecott Copper’s (RTKC) Bingham Canyon mine experienced what is arguably the world’s largest ever in-pit slope failure. The failure initiated along a major, continuous, low-strength bedding fault, named the Manefay bed, and comprised approximately 145Mtonnes of rock and waste dump material. Initial East wall slope deformations were detected some months prior to catastrophic slope collapse by RTKC’s slope monitoring systems. However, the failure mechanism was different to that which had historically been experienced in the prior more-than-100 years of open pit mining. Failure occurred as two separate events, the initial one likely consisting of a frictional failure of rock materials along the Manefay bed itself, before a second phase of failure occurred, which included a large mass of old rail dump material. The combination of these events led to a much larger failure run-out than had been anticipated by the RTKC team which led to loss of, and damage to, mining equipment and infrastructure as well as significant interruption to mining activities. Due to the diligent monitoring of the slopes no safety impacts were experienced at the mine, and as such the details and learnings from this failure can readily be shared with the broader mining and geotechnical industries to avoid similar recurrences elsewhere. This is an extended abstract only. CITATION:Robotham, M, 2018. Bingham Canyon Mine – from adversity to excellence, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 3–4 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

Mary Kathleen Uranium Ltd. recommenced operations in early 1976 following a twelve year period of care and maintenance. Several sections of the plant were modified or completely changed for the second operation. The most important change was the replacement of ion exchange with solvent extraction as the means of purifying and upgrading uranium rich Isolutions Most of the problems experienced in the solvent extraction system originate from the leach liquor which has a strong tendency to form stable emulsions. This has been countered by some careful control of leaching conditions and by closer observation of operations in the solvent extraction area. Most problems have now been resolved and plant recoveries are quite Satisfactory.

Jan 1, 1978

Every year my consultancy business reviews over 100 mines worldwide, primarily focusing on property and business interruption risk. What we have found is that the most successful mines have: identified their principal risks and determined what controls are required to manage or eliminate these risks; and managements systems that underpin these risks and the business in general.

Jan 1, 2003

By Harrison J

The correct selection of equipment to use in a mine is a problem which constantly faces the mining engineer. In some cases a wide choice of equipment with different operating characteristics is available. If this equipment is to be used to assist in moving the ore it may be possible to build a computer simulation model to predict how it will perform. Typical problems that lend themselves to this type of analysis are presented. The computer models are constructed using a recent form of the GPSS computer language, namely GPSS/PC for the personal computer. This language allows the programmer to construct models in a very short time and at a low cost. Of great importance is the easy way in which it is possible to change the models to answer any of the "what if?" questions the engineer may pose.

Jan 1, 1987

By A Jha, R Merz

The substantial growth in world demand for Queensland coking coal has seen a number of new coal mine developments in the Bowen Basin in recent times. The Bowen-Broken Water Supply Scheme (BBWSS) is presently based on water supplied from Eungella Dam and storages at Collinsville to two major pipelines. In early 2004, three successive years of well-below average rainfall had left Eungella Dam at critical levels, threatening the regionÆs mines, which rely on it for their essential water supply. SunWater noted that without significant inflows into Eungella Dam, or the development of a new water supply to the region, existing mines would be severely restricted in water supply, and downstream economic impacts to the region would follow. SunWater investigated the opportunities for additional supply capabilities, including combinations of off-stream storages, additional pipelines, and raising Eungella Dam. An off-stream storage (OSS) was selected as being the preferred option to improve the reliability of the system and head off impending falls in announced allocation for the system. The integrated quantity quality model (IQQM) is the Queensland GovernmentÆs preferred model to define and assess total catchment performance against water security and environmental objectives. Modelling of the performance of the water supply system, with and without the proposed OSS, was required to provide justification to the customers of the system that the OSS was in fact required, and also to optimise the configuration of the OSS within time and budgetary constraints. In the case of the BBWSS, no environmental base flows are dictated by the Department of Natural Resources, Mines and Water (NRM&W) at present and the primary reason for applying IQQM was therefore to investigate the trade-offs between supply options and reliability. SunWater produced IQQM outputs for a range of scenarios for the proposed off-stream storage, and these IQQM outputs were then used as input to a decision-support tool based on the GoldSim modelling package. The GoldSim model was then applied to investigate the water supply reliability for high priority users resulting from various existing and/or proposed water supply infrastructure configurations coupled to the hydrologic system. The GoldSim model included the ability to assess the long-term water supply reliability impacts for each of the water supply end-users for a wide range of user-defined scenarios. Non-technical model users were able to change the size of the off-stream storage, pipeline capacities and assumed climatic conditions and test for themselves the relative benefits (in terms of water supply reliability) of different infrastructure configurations under consideration. The decision tool was of significant benefit in assisting the decision process to SunWaterÆs mining customers. These customers needed to decide if they felt that the increased reliability in their water supplies from the system that would be created warranted the estimated increased charges that would require to be levied to recover costs of the new infrastructure with appropriate profit margins. The conjunctive use of IQQM and GoldSim was successful in demonstrating the impact of both hydrological and non-hydrological issues on the future water supply reliability in the BBWSS and resulted in a decision to proceed with the construction of a new OSS.

Jan 1, 2006

Pulverised coal firing was pioneered in the cement industry prior to the turn of the century. Ash from the coal is absorbed into the mix in the kiln and replaces secondary materials. With high purity limestone coal with high ash content can be used. Fuel cost is a major part of the total manufacturing cost. Cement plants are thus quick to respond to fuel price changes and will use low grade fuels if there is a price advantage. Combustion conditions in a cement kiln differ markedly from a boiler. Flame length is determined by air/fuel mixing but because of fixed secondary air conditions this depends on primary air momentum. Volatile content has some effect on flame length but this can be offset by coal fineness. Much of the heat for cement production is for limestone calcination which is a low grade energy requirement. By allowing long residence time in separate direct fired vessels which then feed the high temperature kiln the energy of materials such as oil shale, tyres and lump lignite can be utilised.

Jan 1, 1987

By Forster G, Datta P. K

Many high temperature industrial processes involve gaseous halogen-bearing environments. Essentially, these fall into three subject areas: power generation, waste incineration and especially extractive metallurgy. Fundamental to any understanding of the process chemistry and efficiency in the process technology is an adequate knowledge of background thermodynamics relating to metal-chlorine reactions. In this context, existing free energy/temperature diagrams for metal chlorides do not include many elements, in particular the so called refractory elements from Group V and Group VI of the Periodic Table, namely niobium, tantalum and vanadium, and molybdenum. This paper reports estimation and calculations of the free energy values for these chlorides. The data is discussed in the context of high temperature chlorination processes.

Jan 1, 1991

In engineering applications of explosives for rock breaking, the released energy is expended mainly into heat, rock crushing and fracturing, seismic waves, air blast, and noise. Those parts of energy which pass into seismic waves and air wave create environmental problems since they are transmitted away from the blast site. In order to predict the environmental effects accurately, one must be able to predict the energy distribution at the source. The energy distribution at the source is significantly controlled by the blast constriction. Consequently, the accuracy of prediction and control of ground vibrations generated by blasting is affected by various matrices of blasting constriction.

Jan 1, 1986

By S J. Woods

As a part of Solid Energy's progressive rehabilitation of the Stockton Mine, it was determined that significant rehabilitation of the existing Mt Frederick Sidecast would be required to ensure the long-term stability of the sidecast. The goal of this rehabilitation is to reshape the existing stockpile into a more stable slope configuration, and the construction of a comprehensive stormwater collection and discharge system. The reconfigured slopes will facilitate the final revegetation of the exposed surfaces and the management of surface and groundwater discharges from the area. This paper briefly describes the specific details of the project and the significance of seismic conditions on the long-term stability of the reconfigured stockpile.

Jan 1, 2003

The unique characteristics of the Target orebody and modernistic approach to mining present significant challenges and a concomitant high potential for new opportunities. The break-away from the traditional labour intensive mining methods improves both safety and productivity significantly. The intention of the paper is to illustrate the application of well known mining methods to the particular requirements of a complex orebody at depth. The evolutionary process followed to establish the final mining method design provides insight behind the finished product, and the modern approach to the planning and service principles equips the reader with a suite of mining engineering ideas.

Jan 1, 2000

By Scott RM

The project management and construction plans adopted by Davy McKee for the Cooper Basin Liquids Project resulted in a project notable for the Relatively short duration from initiation of the design through to liquids production. Two locations were involved, one at Moomba in the far northeast of South Australia some 800 km from Adelaide, and the other at Port Bonython some 40 km from Whyalla. Total expenditure by the owners at the two sites was in excess of $600 million. Matters covered include organisation, transport, construction, industrial relations, project services and commissioning.

Jan 1, 1986

By B R. Olsson, N Marinopoulos

To establish the design and the capacity of the Stanwell Magnesium Plant, Australian Magnesium Corporation Ltd (AMC) with Fluor Australia has modelled the operation of the magnesium plant using ARENA Simulation Modelling. The reliability model has been used to evaluate: surge capacities required between different sections of the plant; critical equipment requiring standby capacity; the number of trains required for different sections of the plant; and potential capital cost reduction options. The reliability model was established using the detailed Process Flow Diagrams, reliability information from literature and maintenance, operation and start-up experience from the Demonstration Plant. The model was run with different plant configurations to assist AMC in determining the most effective configuration to provide the production capacity at the lowest capital cost. The model was not only able to confirm the plant capacity to the independent technical expert but was able to minimise quantitative risk by minimising the quantities of hazardous materials on site. Fluor Australia provided the ARENA simulation expertise and has used this software for optimising new plant design and to establish improvements in operating plants. Reliability modelling is a normal feature of chemical plant design but is rarely used in the resource industry. The experience gained by AMC in the modelling system has indicated that metallurgical plant design can be improved by the application of reliability modelling.

Jan 1, 2002

The Savage River Mines concentrator and pipeline has operated for seven years. During this time some problems of general interest have been overcome, particularly in the area of autogenous grinding in large mills and in pump- ing solids over long distances. The plant flow sheet and equipment at Savage River and the control techniques are. described. Ore type has varied widely over the per- iod of plant operation. Techniques developed to minimise the effect of variations on through- put are discussed'. The main technique is the controlled rejection or addition of grinding Media.

Jan 1, 1975

Modern, high-output, continuous process plant requires heavy capital expenditure and is exroected to achieve a high rate of return upon the investment made, thus its high utilisation is an economic necessity. Downtime is extremely expensive not only in terms of idle capital but also in terms of lost production and revenue. A sound maintenance management system can alleviate the problem of unscheduled stoppages and a key document in the maintenance system is the Work Order because it both initiates work and conveys maintenance control information back to the administrator. This key document must be supported by an information base that provides technical data, job procedures, spare parts, history and costing. To be effective this information must be easily and immediately available to all concerned. Computer technology has developed extremely rapidly over the last ten years and with it a wide variety of on-line computerised maintenance systems. Selection of the most appropriate system for a given industrial plant is not a straight-forward process. Computer requirements for hardware and software must be matched to the requirements of the maintenance system and such matching must be carried out in an ordered and rational way. At Kalgoorlie Nickel Smelter, time was taken to review the existing maintenance system, select, study and test the new computerised maintenance management package and plan its implementation. As a result, the initial target of equipment recognition has been achieved on schedule and within budget.

Jan 1, 1987

The reasons for including treatment of water in Whites and Intermediate open cuts in the overall rehabilitation strategy are given in the introduction. The target quality of the treated water also is discussed. Equipment selections are reviewed and reasons given as to why certain choices were made. The differences between this plant and an ore dressing mill are highlighted. An outline of the operating procedure is included along with a basic flowsheet. Cost estimates are briefly Discussed.

Jan 1, 1984

Geologists often classify ore textures on the basis of the origin of the rock in which they form and the grade of one or more minerals within the ore (Sinclair and Blackwell, 2002, pp 32-36).  Metallurgists, on the other hand, need to know how best to process the ore in order to extract the valuable minerals from it (Petruk, 2000). Geological classification has the following disadvantages:it requires the services of skilled economic geologists, of whom the supply has been dwindling for many years;it is subjective, depending on the perceptions of the individual geologists who make the classification; andit may relate only weakly to processing requirements of the ore. We describe methodology for automatic classification of ore textures from images of drill core. The images analysed are æclassifiedÆ images, in which a particular mineral (or mineral group) is assigned to each pixel. The new methodology is intended to:provide a quantitative and reproducible alternative to traditional geological texture classification,relate to process mineralogy of the ore, andimprove the ore-texture-related input to orebody domaining and geostatistical block models.

Jan 1, 2008

In the last two decades, equipment used in the coal mining operations has become much more sophisticated. The way that work is organised and performed in the industry has also changed significantly. Changes in equipment specification or procedures inevitably means that the risk associated with that equipment or procedure also changes. In an attempt to address this the Joint Coal Board Occupational Health and Safety Trust (JCB) commissioned the University of New South Wales Mining Research Centre and Mine Site Technologies to perform a feasibility study into the development and deployment of Virtual Reality (VR) based training simulators in the New South Wales coal industry. The main aims of the study were to identify, the key providers of VR Technology, the VR options available to the JCB and the information that would need to be included in any simulator. It was anticipated that a critical assessment of these components would produce a format for a cost effective, state of the art simulator that could be readily accessed by all mines. The expectations of the feasibility study were that VR should offer three-dimensional (3D) simulations that are interactive, high-resolution models of real environments based on best practice Safety Management Plans. It was anticipated that the simulations would allow trainees to experience the consequences of poor decision-making and allow them to learn from their mistakes in a safe and forgiving environment. It was envisaged that such simulators would become an addition to the existing training methods used in the industry.

Jan 1, 2003