Search Documents

By G. V. Lewis

"INTRODUCTORY REMARKS""I believe we need to communicate as much as possible with the industry. I don't think that we should be a body that just goes around doing dust surveys and writing nasty letters. We should get together on these problems and try and solve them as a group. I've only been with the Department a little over 12 months. I haven't visited all of your plants. I've visited most of the major open pits and I have had a chance to observe a lot of problems that you have encountered and a lot of the problems that you have brought up this morning. I thought the best thing I could do is perhaps mention a few of the approaches to the problems that my superior has suggested to me and we have discussed in the Department, and then perhaps go over a few of the evaluating problems and what we are trying to do with our dust surveys and perhaps ways and means of improving the present setup."""

Jan 1, 1976

By M. M. Holgate

"Porosity neutron deflection scales can be derived more easily by cumulative correlation than by the conventional method of plotting corresponding points on a graph. The micro-log can be used as a porosity datum for the neutron log by transforming the permeability cut-off it shows to a porosity cut-off by a permeability-porosity function obtained from core analysis. Porosity footage values calculated in this manner from the neutron log are within 20 per cent of core analysis values."

Jan 1, 1960

Safe underground mine backfilling with hydraulic fill requires efficient fill drainage and stable fill retaining walls or bulkheads. If any or both the above two requirements are not satisfied, such a backfilling operation creates unsafe conditions and may lead to backfill retaining wall failures. Mine backfill retaining wall failures are always associated with economic losses, fatalities and interruption to mine production. Mining industry wants to either reduce or eliminate these fill retaining wall failures. The fill retaining wall failures could be effectively avoided through the use of fibre reinforced shotcrete fill retaining walls and engineered drainage systems through the retaining walls. This paper presents the experience of the author in developing, implementing, and monitoring several hundred fibre reinforced shotcrete fill retaining walls at a mine in Australia with the highest safety standard. The details on the mine backfill drainage system and fibre reinforced shotcrete fill retaining wall designs are also presented.

May 1, 2007

By H. P. Jacobi

"The last 25 years have seen tremendous economic pressure placed upon the base metal processor. Industry has responded with technological innovations that have contributed to significant reductions in capital and operating costs. Major changes in processing machinery and philosophy are highlighted for the main unit operations of a base metal mill. Changes in our attitudes on what is environmentally acceptable are also discussed.INTRODUCTIONNewton's law of motion paraphrased states that nothing will change unless there is a pressure to do so.Aase metal processing as a primary commodity related industry has been under severe economic pressure over the last 25 years. This has been brought on by over capacity from new operations in the L.D.C. 's, through material substitution in a host of traditional base metal applications and generally reduced world-wide economic activity. In addition to shrinking markets our collective environmental consciousness has raised effluent standards and workplace hygiene and the employee's as well as government's economic expectations of how much ought to be derived from ''nature's riches''.Industry has responded with technological changes which, it was hoped, would counteract the cost squeeze in which it found itself.I would like to briefly enumerate the major changes, as I see them, that have taken place in the main unit operations that form the normal processing chain for base metals.While the following paper will mention several brands of products, I would like to emphasize that these are the ones that I am most familiar with and is not to say that they are the only manufacturers which have contributed to changes. In fact it ls fair to say that all makers of mining and processing equipment have made improvements to their products, to a greater or lesser degree; they have had to, to still he in business in 1986."

Jan 1, 1987

By James Kear, Romain Prioul, Robert G. Jeffrey, Andrew P. Bunger, Dimitry Chuprakov

"Unconventional gas and geothermal reservoirs are typically naturally fractured and therefore the challenging problem of hydraulic fracture (HF) growth through naturally fractured rocks is an important issue especially for the development of accurate predictive HF models. This paper presents results from laboratory experiments in which HFs have been created in both sandstone and crystalline (gabbronorite) rock specimens such that they impinge either orthogonally or at an oblique angle on an unbonded, machined frictional interface. Depending on the conditions of each experiment, the fractures either cross or are blunted at the interface. The growth behavior was ascertained for these experiments based on a synthesis of the injection pressure record, active ultrasound monitoring, and direct post-experiment inspection of fractured specimens. From these experiments we observe: 1) A contrast between direct crossing and crossing with an offset for orthogonal and oblique intersection, respectively, 2) Apparent independence of crossing/blunting behavior on the friction coefficient for orthogonal intersection, 3) Dependence of the stresses required to promote crossing on the intersection angle between the HF and NF, 4) Existence of cases in which the hydraulic fracture crosses but then essentially ceases propagation such that all fluid is diverted to the interface. INTRODUCTIONHydraulic fracturing is a vital technology used to increase the productivity of oil, gas, and geothermal wells. Predicting hydraulic fracture (HF) growth is, in turn, critical to design of hydraulic fractures that grow to the desired length, accept the desired amount of proppant, and remain contained in the reservoir without unwanted height growth into surrounding layers (e.g. Economides and Nolte, 2000). The importance of HF modeling has prompted 6 decades of research during which simulators have become more efficient, more accurate, and have addressed a growing range of complexities (see review of e.g. Adachi et al., 2007).One of these complexities is the interaction between HFs and mechanical discontinuities such as natural fractures (NFs). Efforts in this area have been mainly driven by development of unconventional (i.e. low permeability) oil and gas resources because essentially all viable low permeability reservoirs, including shale gas/oil reservoirs, are naturally fractured to some degree (King, 2010). One of the most important questions for developing effective HF stimulation strategies in these reservoirs is whether the hydraulic fracture(s) is/are expected to be single-stranded or whether interaction with the NFs will lead to network-like growth. The basic building block for numerical simulators that can address this question (such as Kresse et al., 2013 and Weng et al., 2014) is whether an HF that intersects an NF will cross the NF or whether its growth will be captured by the NF so that additional fluid injection pressurizes the NF but does not generate ongoing growth of a new HF. These scenarios, including subcategories such as crossing with an offset, have been recognized for several decades (Daneshy, 1974; Warpinski and Teufel, 1987, and as recently reviewed and expanded by Chuprakov et al., 2013)."

Jan 1, 2015

By Joseph Licavoli, Paul Sanders, Yang Yang

"Al-Sc-Zr alloys form thermally stable L12 precipitates which provide high temperature strength. Although the overall fraction of L12 Al3Sc and Al3Zr may be increased by increasing scandium (Sc) and zirconium (Zr) content, such additions may increase primary phase fractions and do not produce desirable secondary phase morphologies. Rapid solidification techniques, such as melt spinning, increase solute atom concentration within the matrix. When the supersaturated matrix is aged, higher precipitate volume fractions at low Sc and Zr levels can be achieved improving high temperature strength. Melt spinning was used to rapidly solidify (107 k/s) a thin ribbon of Al-0.5Sc-0.4Zr at. %. The ribbon was compacted and extruded into 99.8% dense rods, and then aged using multi-step isochronal heat treatment up to 600°C. Precipitation strengthening was evaluated by ambient hardness measurement. The ambient hardness of melt-spun ribbon after precipitation hardening increased by 450 MPa (~67% increment) during isochronal heat treatment.INTRODUCTION Small Sc and Zr additions to aluminum improve strength and creep resistance above 300°C due to tri-aluminide precipitation of Al3(Sc,Zr) in L12 structures similar to ??, Ni3(Al,Ti) in nickel superalloy, but the Al3(Sc,Zr) particles have a Sc-rich core surrounded by Zr-rich shell (Figure 1). The Al3Zr shell limits atomic transport between the Al3Sc core and the matrix and reduces coherency strain. These factors reduce precipitate coarsening rate at elevated temperature (Bergner & Van Chi, 1977; Fujikawa, 1997; Knipling et al., 2011; Clouet et al., 2006).Figure 1. Simplified schematic model of precipitate Al(Sc,Zr) in Al-Sc-Zr alloy. Shell is rich of Al(Zr) intermetallic phase, particle core is rich of Al(Sc) intermetallic phase (after Voorhees, 2006). Numerous Al3(Sc,Zr) particles increase alloy strength and creep resistance as the precipitates impede dislocation glide and to a lesser extent climb. Previous work on ternary Al-Sc-Zr alloys show large strength increases versus binary Al-Sc, and Al-Zr alloys in Table 1."

Jan 1, 2018

By J. C. Escobedo, J. M. Almanza, A. Flores, Cortés. D. A.

Secondary aluminum dross, which has been exposed for several years to atmospheric conditions, was characterized using chemical analysis, X-ray diffraction, optical and scanning electronic microscopy, and energy-dispersive spectroscopy. Based on the characterization, a method to purify the solids is presented. This method starts with the washing of the dross in boiling water to eliminate the soluble compounds like Na and K, followed by the physical separation of the metallic aluminum by milling and screening. Finally, an acid lixiviation process is applied using three different acid solutions, HCl, HNO3, and H2SO4. The best results were obtained using HCl. The main insoluble components of the dross after lixiviation were Al, SiO2, and Al2O3. MgAl2O4, AlN, Si, and Na2Al22O3·2H20 species were also found. Based on the alumina content, the solid product could be suitable as a raw material in the manufacture of castable refractories or metal matrix composites.

Jan 1, 2005

By Paul Hughes

This paper summarizes current underhand paste backfill mining as applied to Goldcorp Inc?s Red Lake Mine, Newcrest Mining Ltd?s Kencana Mine and the Lanfranchi Nickel Mine as well as ongoing research at the University of British Columbia?s Norman B. Keevil Institute of Mining Engineering. The Red Lake Mine utilises a 6 m wide undercut with a 2 MPa unconfined strength paste in order to selectively mine its high grade, high-stress orebody. Kencana?s orebody is located in a poor rock mass environment. An 8 m wide, 2 MPa unconfined strength paste sill allows a safe working condition for its high grade orebody. The Lanfranchi Nickel Mine utilises a cable-supported, 2 MPa paste, with 12 m span sills, to optimize the mining of the squeezing rock mass. This paper details the rock mechanic hazards, ground support techniques, paste practices and unique conditions for each mine. Further, an update of ongoing research at the University of British Columbia, focussing on the optimization of safe mining in underhand cut-and-fill mining in high-stress/weak rock masses, is presented.

May 1, 2011

By Janice Zinck, Maziar E. Sauber

"To counter the recent uncertainty in the rare earths market, diversify the supply source, and help meet the future demand in this sector Canada initiated development of several new rare earth deposits. In the past few years, a number of various studies on rare earths plant design have taken place mainly covering process development, process selection, and flowsheet design. The purpose of this paper is to provide an overview of known domestic and potential resources and reserves of rare earths and their status quo with a focus on the metallurgical processes using the information available in the public domain. Plant designs currently under consideration in Canada are reviewed and evaluated. An outline of the areas of opportunity for selective innovation and technology development in the rare earths flowsheet development and the associated risks and rewards is provided.INTRODUCTIONThe rare earth elements (REE) have a very small annual market, but they are categorized as very strategic metals vital to global economic growth due to their indispensability to the development of modern defence system, green technologies and electronic applications. The International Union of Applied and Pure Chemistry (IUPAC) defines the REE as the 15 elements on the lanthanide series on periodic table of elements, plus yttrium and scandium. REE are classified as light rare earth elements (LREE; La to Gd), and heavy rare earth elements (HREE; Tb to Lu). Physical properties and chemical reactivity of yttrium is similar to those of HREE, thus it is categorized as such. Properties of scandium are not similar enough to classify it as either a LREE or HREE (Weng et al., 2015; Sappin & Beaudoin, 2015). However, the mining industry does not always abide to this definitive classification of the split between LREE and HREE. Therefore, in a comparative study of projects, there is a need to pay attention to how the elements are classified."

Jan 1, 2016

By C. Cano

One of the main concerns within the mining industry is to minimize the impact of tailing facilities to the environment and nearby communities. Since the implementation of the first thickened tailings disposal (TTD) methodology at Kidd Creek in 1964, the thickened tailing disposal has been growing alternative disposal technology to mitigate the environmental impacts. Technical investigations on the TTD technology have been studied in detail to counteract the increasing shortage of water resources. One of the benefits observed with TTD is its resistance to potential earthquakes, particularly in zones with high seismic activity (Los Andes). TTD technology optimizes the maximum possible density for the material and generates a negative internal pore pressure in the material due to the surface and sub-surface water evaporation. This internal pore pressure should be enough to resist the pores pressure to which tailings are subject due to an earthquake action. The objective of this study is to verify the Shrinking Limit (SL) of thickened tailings during initial deposition and in the long term and the ability of tailings deposited by TTD would resist liquefaction. Fresh tailings coming from a flotation process of a copper plant concentrator were used. The samples put under cyclical three-dimensional tests associated with maximum credible earthquake magnitude range of 7.0 8.0 to develop a curve for the safety factor v/s depth for dry densities related to the maximum density obtained at the SL. At a dry density of 1.65 t/m3 liquefaction did not occur at any depth. At 90 % of dry density of 1.51 t/m3, liquefaction did not occur at earthquake magnitudes of 7.0 or 7.5 nor at any depth but liquefaction occurred at magnitude 8.0 between 0 m and 14.5 m; below 14.5 m, liquefaction does not occur.

Jan 1, 2007

By P .. D. Vaillancourt, D. F. Sangster

Several occurrences of disseminated galena, including a former producing mine, are found in Pennsylvanian fluviatile sandstone of the Salmon River Basin, Cape Breton Island, Nova Scotia. Detailed study of the distribution of these occurrences has revealed that highest galena concentrations are found in sandstone overlying channel-shaped depressions in felsic basement rocks. These buried depressions, in turn, correlate in position with modern streams in areas of basement exposure. This correspondence suggests that the latter are at least partially controlled by an exhumed Pennsylvanian topography. If this is correct, then several other streams in the area, lying on basement, may be used to locate possible undiscovered lead deposits in sandstones of the Salmon River Basin.

Jan 1, 1990

By J. W. Austin

"Introduction The Brenda dust collection system was originally designed to handle air at the 5000 ft. elevation with less than 1 grain of dust per cubic feet of air handled. The temperature variation is from 32°C in the summer to -20°C in the winter.DUST COLLECTIONOriginal Equipment 1. Primary Crusher 2 compartment baghouse, shaker type design capacity - 17,000 cfm2. Primary Screening 3 compartment baghouse, shaker type design capacity - 30,000 cfm3. Secondary Crusher 4 compartment baghouse, shaker type design capacity - 45,000 cfm4. Secondary Screening 4 compartment baghouse, shaker typedesign capacity - 60,000 cfmThe original dust collecting equipment was designed using a napped terylene fabric at an air to cloth ratio of 5:1. The ducting was designed to handle the dust laden air at 3200 ft. per minute with all elbows and blast gate sections rubber lined. The hoods and the pickup velocities were designed to handle the anticipated low dust counts."

Jan 1, 1976

By James F. Archibald

Research has been conducted for the Workplace Safety and Insurance Board of Ontario (WSIB) to characterize thin, spray-on lining materials (TSLs), as well as combinations of TSLs and conventional spray supports, and to assess their capacity for inhibiting damage created by mining-induced rockbursts. This study has been performed to assess the capabilities of such support systems for preventing rock and support material damage that often results due to rockbursting. A variety of TSLs and other spray support media were subjected to the effects of simulated rockbursting, through use of explosive detonation trials, to evaluate their damage mitigation capacity. Results have validated that TSLs and variant layer combinations may be as effective as or better than conventional support materials for mitigating rockburst or like damage in highly stressed mine environments. In civil engineering construction, and typically in underground tunneling operations where concrete linings are applied, liner deterioration is a continuing and pervasive problem that often requires expensive and time-consuming rehabilitation effort. The ability of TSLs to provide effective concrete structural reinforcement while providing sustainable resistance against underground or restricted environmental hazards, as with fires or dynamic failure events, may permit wider use of TSLs than is currently foreseen by the mining industry. Significant benefits for use of TSL materials in concrete liner rehabilitation and for concrete material protection have been assessed.

May 1, 2006

By R. A. Ozerkevich, R. J. Voisey

"SherrGold's MacLellan V ne is located about five miles south east of Lynn Lake immediately to the east of the Keewatin River. (Figure # 1)The property is accessible by an all weather road, leading north from the provincial highway 391, which links Lynn Lake with the Town of. Leaf Rapids and the city of Thompson to the south.The MacLellan Mine (formerly the Agassiz property) was discovered in the early 1950's and optioned from Comiesa Corporation in 1979 by Sherritt. SherrGold Inc. was formed in September 1985. Sherritt then transferred the MacLellan Mine, 15 other gold prospects in the Lynn Lake area and the old Lynn Lake nickel-copper mill to SherrGold. At the same time Sherrgold entered into a management agreement with Sherritt whereby Sherritt would develop and operate the MacLellan Mine and conduct SherrGold's exploration activities.The ore body as outlined in the original feasibility study is expected to produce in excess of 300,000 ounces of gold and 450,000 ounces of silver over the next 5 years. However the deposit is open to depth and exploration is continuing on and around the main zone and the many satellite deposits.The start of construction of the MacLellan mine and mill was scheduled to phase in with the closure of the Fox copper-zinc mine located 30 miles west of Lynn Lake. The majority of the employees from the Fox Operation were either employed at the MacLellan mine or relocated to Sherritt's Ruttan Operation."

Jan 1, 1987

By E. W. Shaw

The past year (1950) has been a big one for the oil industry in Canada, with new records being set in almost every phase of exploration and development activity. New highs were reached in acreage holdings, in geophysical activity, in wildcat drilling, and in field development and production. The only item that did not show a substantial increase over recent years was the amount of reserves added by new discoveries. This was not due to a decrease in the number of new discoveries, however, hut rather to the fact that most of the discoveries were made during the later months in the year and could not be fully evaluated by the year end. The foregoing remarks pertain mainly to activity in Western Canada. In Eastern Canada, operations continued on a modest scale. with exploration drilling down slightly from the previous year but with development drilling and production at about the same level. Returning to Western Canada, it is observed that the general exploration play was one of expansion and intensification. The issuing of new petroleum and natural gas regulations by the province of British Columbia precipitated a moderate entry of companies into the northeastern part of the Province.

Jan 1, 1951

By Laurence McGonagle

"The Highland Uranium Project (HUP) is located approximately sixty miles northeast of Casper, Wyoming and is owned and operated by Power Resources, Inc. (PRI). With an annual production of680 tonnes (1.5 million lbs) U308, HUP is one of the largest uranium producers by in-situ leach (ISL) in the western world. Uranium is currently produced from four wellfields with a total flow rate of approximately 1,135 m3/hr (5,000 gpm). The carbonate leach solutions are processed by anion ion exchange at two satellite facilities located in close proximity to the wellfields. The loaded resin is transported by truck to a central processing facility for elution of the uranium. Uranium in the pregnant eluant is precipitated and washed prior to calcining.Wastewater from the satellite facilities is treated and used for irrigation at a Land Application Facility. The wastewater generated at the central processing facility is injected into a 2,750 m (9,000 ft) deep waste disposal well.When economical mining of the orebodies is complete, restoration of the groundwater is initiated. There are currently two wellfields at HUP undergoing ground water restoration. Phase I restoration consists of removal of the carbonate leach solution from the ore body. Phase II includes treating the withdrawn fluid with reverse osmosis and reinjection of the permeate into perimeter wells.Future plans include construction of additional satellite facilities at the Gas Hills Project and other economical deposits located within 240 km (150 mi) of HUP. The capacity of the central processing facility will be increased to 1,815 tonnes (4 million lbs) U308 per year by late 1999."

Jan 1, 1998

By H. Deveci, E. Y. Yazici, A. D. Bas

The leach solutions of waste of printed circuit boards (WPCB) may contain a wide range of base and precious metals with different concentrations due to heterogeneity of these wastes in composition. Therefore, selection of a suitable metal recovery method is of practical importance for downstream processing of pregnant leach solutions of WPCB. Sulphuric acid leaching of WPCB in the presence of a suitable oxidant is capable of dissolving base metals as well as precious metals such as silver. In this study, cementation of silver from sulphuric acid leach solutions of WPCB using metallic copper, aluminum and zinc was studied. The WPCB sample was assayed to have a silver content of 694 g/t. A synthetic leach solution containing 20 mg/L Ag in sulphuric acid solution (0.51 M H2SO4) was prepared based on the silver concentration in pregnant leach solutions of oxidative sulphuric acid leaching tests. Total sulphate concentration ([SO4 2-]T) was kept constant using sodium sulphate at 1 M. Metallic powders of copper (-850 +600 µm), aluminum (-425 +45 µm) and zinc (-45 µm) were used in the cementation tests. The effects of metal type (Cu, Al or Zn), dosage of metal powders (above the stoichiometric ratio by up to 2000-fold) and temperature (20-80°C) on the rate and extent of silver extraction from the solution was investigated. The effect of presence of copper on the cementation performance was also tested. Under suitable conditions high silver recoveries (>90%) was achieved using metallic copper and zinc while aluminum yielded the lowest silver recovery (i.e. 40% Ag). The kinetics of cementation by zinc was comparatively higher than that of other metals. Increasing the temperature was observed to significantly enhance both the rate and extent of silver cementation. SEM-EDS studies were performed to characterise the metallic powders after cementation.

Jan 1, 2016

By A. Vien, B. C. Flintoff, R. P. Edwards

"This paper provides a critical review of the development and application of advanced controls in mineral processing at the industrial level. These algorithms can be sub-divided into four broad categories: Kalman filter, self-tuning, extended horizon, and knowledge based or expert systems. Applications from each category are described outlining the benefits derived, the relative advantages of that particular controller, and potential limitations of the controller which may inhibit their more widespread application. The paper will conclude with a description of control algorithms which are currently in the rudimentary design stage, but may hold tremendous potential for mineral processing control systems in the next decade. INTRODUCTIONThe Canadian mining industry has a large installed milling base and many plants are run with manual or low level automatic process control. The competitive pressures imposed by the market will not allow these operations to ignore the significant increase in efficiency that can be achieved through the effective application of advanced process control. These improvements will come in the form of better quality, higher productivity and reduced costs.There have been quite a number of reports of successful applications of advanced control in mineral processing applications. As this trend continues, and more of the work is documented, the technology will be more effectively transferred to process and control engineers. It is the authors' opinion that the most difficult problems facing process control are not really technical in nature. Rather, they lie more in process control education. This extends from management, through engineering to the operators.The purpose of this paper is to provide a tutorial type overview of some of the more frequently encountered advanced control algorithms. The assumption is that the reader has a superficial knowledge of this technology. In the discussions which follow, several techniques are explored within the framework of simple process examples. Industrial examples are cited for each and an evaluation of the expected longer term potential is given."

Jan 1, 1992

By T. Nyabeze

This paper presents the experiences and views of women involved in the mining industry as determined from a questionnaire that was circulated across the Canadian mining industry. Globally, there have been significant studies done to understand the historic and global variety of women?s participation in this industry1. The reason for focusing on women?s experiences here in Canada is because women?s percentage representation at 14.4% in the mineral industry workforce falls below the overall labour force average of 47.4%2. Notably, a recent article in the Globe and Mail newspaper points out that adequate representation of women in leading of organizations is more of a matter of competitiveness and innovation rather than purely a ?women?s issue?3. This paper will provide some insight into the reasons why women join and stay in the mining industry and shed some light into the reasons for the overall low representation in this sector. The authors believe, as stated in a study from the London Business School, that a gender-balanced workforce is one way of providing the best results in areas that drive innovation4. Women represent a key stakeholder group that can help enhance the mining industry?s sustainability through innovation. The women who responded to the questionnaire represent many different areas within the mining industry, including a broad range of roles in industry, government, academia and in the supplies and services sector. The paper is intended to raise awareness about issues that women encounter that contribute or detract from career satisfaction in the mining industry. The survey provides an overall understanding of why women pursue or work in mining, and why women either remain or choose to leave it. The advantages and disadvantages experienced by women are highlighted, along with a summary of the possible initiatives that could be undertaken by employers as opportunities to improve the attraction of the mining industry for career minded women. As well, the survey provides a summary of the top ten features that are already in place at various organizations and community groups that have been identified as key for supporting and encouraging women to join and remain in the industry. Not surprisingly, the survey identifies that one of the key ingredients for retention of women in mining is the provision of mentors and sponsors. Another key aspect for retention is the provision of progressive employment policies that address the need for a degree of flexibility in work hours and a culture of balance between work and personal life demands. The survey and results are portrayed only from a female perspective since it is largely women?s perceptions that will inevitably be transmitted to others who plan on entering the field.

Oct 1, 2010

By A. E. Gran

"QIT -Fer et Titane Inc. currently produces and markets four main products: a titania slag named SORELSLAG for the white pigment production, a high purity pig iron known as SOREL-METAL mainly used in the ductile iron casting industry, an ilmenite ore for blast furnace applications called SORELFLUX and high quality steel billets SORELSTEEL employed in the wire rod fabrication. Moreover , QIT also manufactures high quality iron and steel powders labeled ATOMET for the powder metallurgy industry through its wholly owned affiliate. Quebec Metal Powders Limited. The company operates. rock ilmenite mine near Havre St. Pierre and produces its slag and ferrous products from its metallurgical installations located in the Sorel/Tracy region. QIT. born in 1948 from a joint-venture between Kennecott Copper Corporation and New Jersey Zinc Company, was acquired from BP Minerals by RTZ Corporation PLC in 1989 and remains its wholly owned subsidiary ever since.lImenite is a mineral rich in both titanium and iron oxides. QIT's proprietary mineral enrichment and electric smelting processes permit the concentration of the ilmenite ore and the separation of its main constituents to produce a 80% TiO2, slag and a high purity molten iron which is further transformed into iron ingots (pigs), steel billets, iron and steel powders.QIT's ilmenite deposit is located in the Lake TIo-A1Iard area, 43 km inIand from Havre St. Pierre, a community on the north shore of the St. Lawrence River some 960 km from Montreal. The orebody, covering some 542 000 m2, consists primarily of coarse-grained ilmenite (FeO.TiO2) with disseminated fine lenses of hematite (Fe2O3). The worthless mineral (gangue) associated with ilmenite is mainly anorthosite, a complex silicate. QITs mining operations are carried out using conventional open pit methods in a 500 m by 600 m horse-shoe shaped mine with nine benches developed. Primary blasting is performed on a weekly basis during the mining season. Blasted ore is trucked to the crushing station to be broken down to 15 cm and 7.5 cm sizes, respectively, by means of a primary jaw crusher and a secondary cone crusher. Minus 7.S cm ilmenite is then loaded into hopper cars for the 43 km trip to the Havre St. Pierre terminal where it is stockpiled and reclaimed by under-ground conveyor chutes to a ship loading tower at the dock. The crushed ore is shipped to QIT's smelter located in Sorel in 40 000 tonne carriers from April to December."

Jan 1, 1995