Search Documents

By Raymond D. Potts

"Minntac is a taconite mining, concentrating and pelletizing operation located near the town of Mountain Iron, Minnesota, U.S.A. It is totally owned and operated by USX Corporation and represents its largest source of domestic iron units. Minntac began producing fluxed pellets in 1988 and has produced both acid and fluxed pellets since then. This paper compares the acid and fluxed pellets produced at Minntac. It reviews modifications that have been made to the plant flowsheet and discusses areas recognized for improvement since the beginning of fluxed pellet production. It also comments briefly on the performance of Minntac fluxed pellets in USX blast furnaces and the future of fluxed pellets at Minntac.IntroductionMinntac was built in three steps with each step designed to produce 6 million long tons of acid pellets per year. The actual production has varied though. Figure I shows the production by year at Mirmtac. Step I began production in 1967, Step 2 in 1972 and Step 3 in 1978. Mirmtac produced 16.5 million tons in 1979 but only 3.5 million tons in 1982 when the facility was shut down for six months because of the lack of demand for pellets. Since the initial start up, Mirmtac has produced over 200 million long tons of pellets. Until 1987, all the pellets produced were ""acid"" pellets. In 1987, equipment to produce ""fluxed"" pellets was installed and tested. In 1988, full scale production of fluxed pellets began."

Jan 1, 1991

"The successful commissioning and ramp up of the Albion Process™ at the GPM Gold Project relied on the successful scaling up of the process from batch and continuous pilot plant campaigns (Voigt et al., 2015). Critical information about reaction kinetics and residence time, grind size and pulp density were determined at the laboratory scale and successfully applied to the commercial scale. A limitation of small scale testwork, is that some parameters cannot be measured reliably and scaling up is a function of the physical size of the equipment which isn’t possible to test with laboratory scale equipment. Oxygen mass transfer rate is one such parameter since this is a complex interaction of many factors including slurry temperature, solution and slurry chemistry, slurry viscosity, agitator type, dimensions and power, oxygen bubble residence time, oxygen purity, tank geometry and oxygen injection technique. Oxygen generation represents an important operating cost for the Albion Process™. Pivotal to the Albion Process™ operating economically at atmospheric pressure is the capability to efficiently transfer oxygen while utilising as much oxygen injected to the process as possible. To respond to this Glencore Technology developed the HyperSpargeTM supersonic gas injector. This paper compares the HyperSparge™ against other sparging techniques to quantify the benefits of oxygen injection via a supersonic gas jet on scale up of the oxygen mass transfer system. The paper then examines plant survey data from the GPM Gold Project to demonstrate the very high oxygen utilisation that can be achieved with a correctly designed oxygen mass transfer system.INTRODUCTION One of the main challenges in chemical reactor design is the scale-up of processes from the laboratory to industrial scale. Processes which cannot be faithfully simulated with an experiment at the laboratory scale face challenges due to the physical dimensions and complexity of full scale operation. One example of this is the design of oxygen mass transfer systems in atmospheric oxidative leaching circuits such as the Albion Process™. A number of constraints associated with the use of laboratory scale equipment to design full scale circuits are involved in gas mass transfer processes in agitated slurries such as the Albion Process. Chiefly, typical laboratory and pilot size equipment lacks the required volume to provide useful design data without relying on empirical correlations: the specific agitator power input is artificially high, the bubble residence time in the vessel is artificially low, the oxygen partial pressure at the base of the vessel is artificially low and the oxygen delivery method may differ significantly to the industrial process. Further, the dynamic nature of the process introduces additional impacts on gas mass transfer, including the presence of solids, recycle streams and minor elements, plus the variances within the reality of a process plant such as disruptions or variance of feed quality."

Jan 1, 2017

By R. Hendricks

"IT IS a pleasure for me to appear before yon today and to have this opportunity of reviewing with you recent developments in the world lead and zinc industry. To provide essential background material, I propose reviewing the period from 1950 to the present, a period which has undoubtedly been the most hectic in the long history of the industry.In capsule form, the pattern for this period is one of repeating cycles of boom and recession, of failure through research to develop adequately new markets and new uses for lead and zinc, of surplus production and growing inventories, of price instability, and lastly, of an abdication in some sections of the industry of responsibility for control of its own destiny by turning to governments for support in time of stress. This is not a pretty picture but, as the 1950 decade ends, there are signs of a new maturity and of a growing determination on the part of the industry to put its own house in order.The difficulty suffered by the world's lead and zinc industry in the current decade originated with the support extended to it in 1950 by the U.S. Government at the time of the Korean conflict. Recalling the shortage of base metals in World War II and fearing that the Korean conflict might develop into World War III, the U.S. Government in 1950 adopted a policy to encourage the production of lead and zinc, both domestically and abroad by means of development loans and long-term floor priced purclu.se contracts."

Jan 1, 1960

By W. J. Young, K. B. Macneill, C. N. Smith

"A BRIEF HISTORY OF THE MURRAY BROOK MINERAL DEPOSITDuring the mid-1950's intensive exploration activity in northern New Brunswick followed the discovery of the world class Brunswick base metal deposit. Using the prototypes of modern airborne geophysical and geochemical exploration techniques many mineralized areas in the Bathurst-Newcastle area were quickly identified. This base metal - silver camp is situated within the metavolcanic - metasidementary rocks of the Tetagouche Group which forms a roughly circular caldera-chaped voloanio complex of Ordivician age.One of the early results in the exploration history in the camp was the discovery of the Murray Brook Deposit by Kennco Explorations, (Canada) Limited. During routine ground checking of geophysical anomalies, most of which turned out to be graphitic schist, the discovery of some copper bearing float was made by the exploration team. This encouraged the company sufficiently to carry out a regional stream sampling program which lead to a large anomaly associated with a hematitic gossan. Diamond drilling of a weak Slingram anomaly over the gossan zone resulted in the discovery of massive sulphide lenses. This was followed in 1956-7 with an intensive drilling program. The result was the delineation of a potential ore body containing an estimated 23 million tons with an overall grade of 0.44% copper, 0.86% lead, 1.95% zinc, 25.73 g/tonne (0.91 oz/ton) silver, 0.28 g/tonne (0.01 oz/ton) gold. Within this package were higher grade zones of copper and lead-zinc mineralization approaching ore grades.A thick blanket of gossan was present and is reported to have caused the drillers considerable trouble as they attempted to penetrate it to get to the underlying sulphides. The gossan, consisting of iron oxides and silica fragments sits on top of the massive sulphides and attains a remarkable thickness of 45.5 meters (150'). Early work had suggested that the gossan was enriched in gold and silver. If this were the case and if the precious metal could be leached out with cyanide, then mining and recovering those values might be economic.With this in mind Northumberland Mines Limited optioned the property from Kennco in 1985. Preliminary leach tests indicated that indeed the gold in particular leached readily. Subsequent drilling of the gossan (using triple core barrel technology for better recovery of the easily ground core) indicated 1,536,363 tonnes (1,690,000 tons) with an average grade of 1.05 g/tonne (0.037 oz/ton) gold and 42.13 g/tonne"

Jan 1, 1993

By Ralph H. Cleland

GENERALLY speaking, the Industry lost ground in 1941 in its accident experience. Though the frequency of compensation accidents was but slightly higher than in the previous year and well below past experience, our fatality rate shot up to that obtaining in 1938, and the average cost per man employed was the highest for some time. The number of fatalities was 56 in 1941 as against 33 in 1940. The average cost of compensation per man employed was $34.25 in 1941 as against $28.43. There was but a slight increase in the number of men employed. Accident prevention efforts were maintained, as shown by our frequency, but our accidents were of a more serious nature. In a period of considerable labour turnover, with many new men entering the Industry, especially the base-metal division, and much mental distraction, we might well have expected a high rate of accidents. That this did not occur is a tribute to managers, supervisors, and workmen alike. We all regret the high fatality rate and one must consider why this occurred. So far as it is possible to determine, there is no apparent explanation. There were no disasters. The accidents occurred to the same class of work-men, both in respect to jobs and age groups, and from the same age-old causes that we all know so well. Luck is a big factor in the seriousness of an accident; the solution lies in preventing accidents, even first-aid cases. Generally speaking, if minor accidents do not occur, major accidents do not occur.

Jan 1, 1942

By G. E. Cole

"Amongst the mineral products of Canada gold holds the second place in value of yearly output. . . . . .The production of gold has increased steadily during the past six years and has somewhat more than doubled in that time. For the past four years Canada has been third among the gold producing countries of the world, surpassed only by the Union of South Africa, and the United States of America," and now yields somewhat more than 9 per cent of the annual output of the world."-"The Gold Situation in Canada". Bulletin of Development Branch, Canadian Pacific Railway. The history of gold mining in Canada is comparatively modern and does not take one further back than the late 'fifties of the 19th century. If the efforts of the early explorers in Canada were expended in "seeking with equal ardour, proselytes and gold", history fails of any record of their success in the search for the precious metal. As early as 1849 not a few Canadians travelled from the east by land and water to the Californian goldfields. In the then settled part of Canadathe east-people were alive to the value of any mineral discovery; but the west, owing to its remoteness and to there being no ready means of communication, was virtually isolated from the east.

Jan 1, 1927

By Brian Hart, Stamen Dimov

"The Time of Flight Secondary Ion Mass Spectrometer (ToF-SIMS) is unique in that it measures the outermost atomic layers of any material. The technique is particularly suited for determining surface chemical composition of mineral particles. It is most commonly used as a diagnostic tool to measure mineral surface chemical variability in plant and bench top flotation separation processes. Recently, research towards understanding the full capability of the instrument has resulted in the development of new diagnostic applications related to various Au extraction technologies and the development of the ToF-SIMS as a predictive tool for assessing the chemical reactivity of the ore.In this paper we will present a brief review of the ToF-SIMS technique with recent advances in instrumentation and methodologies including:•,?recent developments and advances towards a semi-quantitative approach to the evaluation of mineral surface modifiers (ex. Cu),•,?flotation case studies investigating activator, depressant and collector loading variability within a flotation process,•,?the recently developed chemical reactivity test which we believe has the potential to predict the behaviour of minerals in a flotation test in response to chemical transfer during grinding,•,recent applications for determination of surface Au preg-robbed in carbonaceous materials.A portion of this material has been recently presented at the COM 2009 meeting and at SIMS XVII (see Dimov et al 2009 and Hart et al, 2009).INTRODUCTIONIn flotation seperation surface chemistry is the principal determinant for selective separation of the various mineral phases (Ralston, 1994, Smart et al, 2003). Determination of this hydrophobic/hydrophilic balance by particle therefore requires correct identification and selection of the particular mineral phase(s) followed by a statistical analysis of the surface chemical characteristics of the particles with an estimation of the spread of values (Smart et al, 2003)."

Jan 1, 2010

By Simon C. Dominy, Alwyn E. Annels, Paul Wheeler, Suzanne P. Barr, G. Simon Camm

Abstract-Narrow veins are an important world-wide source of silver, tin, uranium and particularly gold. To potential financiers, this style of mineralization is viewed as high risk because of the often relatively small resource involved and high cost of estimation. In many cases diamond core drilling will not enable resource estimation beyond the inferred and indicated categories. Exploratory underground development is required to define measured resources. The definition of geological and grade continuity are major factors in narrow vein assessment. A measured resource must be based on strong geological and grade continuities. Narrow veins, generally less than 3 m wide, are complex geological phenomena, which commonly display unpredictable geometry and grade distribution. Variations in structural continuity, dip, strike, width, mineralogy and specific gravity are common. Veins may be composite, with ore-grade mineralization restricted to a specific structural domain. Branches, intersections and braided zones are common features. Potentially high-grade zones are often localized within ore shoots, which are surrounded by barren/low-grade regions. Resources must be determined as closely as possible to reality and reflect the distribution of the commodity in the rock. Estimation has three main requirements: (1) geological study to determine orebody nature; (2) estimation of tonnage and grade, and (3) the presentation of this information using a classification that is clear, unambiguous and bankable. Estimation methods employed are either classical or geostatistical; however, classical methods are often used because of the difficulties in applying geostatistics. Grades generally show a strong positively skewed distribution testifying the presence of high-grade values. Problems exist in the applicability of cutting outlier values risking over- or underestimation of grade. It is generally believed that where resource estimates are in error, poor geological control is usually the cause. Overestimation can lead to the closure of a mine through lost revenue and capital. An understated estimate can result in an opportunity missed for profit and/or greater economies of scale. Definition of reserves involves the consideration of economic and engineering data, to decide which part of the resource is economically mineable. Geology plays a similarly important role at this stage in the assessment of likely mining method, dilution, recovery etc. Throughout resource/reserve estimation, it is crucial that the amount and quality of the data and the geologist’s experience are relevant. The impact of geological understanding on estimation is often undervalued or assumed to be of lesser importance than finding grades and tonnages. This paper discusses the geology of narrow vein deposits and the importance of geology in their evaluation.

Jan 1, 1997

This paper states how alloy and welding advances have made possible the rapid development of the use of aluminum in the construction of equipment for earth moving and off -highway rock hauling. The main details are given regarding the construction and field testing carried out on an aluminum prototype body. The test results of strain gauge readings are analysed, and a description is given of how these have been applied in subsequent designs. The increase in the number of aluminum units put into the various types of service in Canada, as well as the problems encountered, is described, and the experience gained from five years of field service is discussed in some detail. An assessment is also made of the durability of the e units. The economics of using aluminum, together with the current development position, are reviewed, and predictions are made for considerable future increases in the use of aluminum units in open-pit and off-highway operations.

Jan 1, 1964

By The Hollinger Mill Staff

MR. E. L. Longmore (l), in presenting this paper at the Annual General Meeting, suggested that it was neither desirable nor necessary to read any but the briefest portion of the paper. He wished to emphasize that the scale of the milling operations at the Hollinger not only provided several units in continuous operation to ensure that the test work was being carried on under normal conditions, but also provided a large and competent staff to supervise such an extensive experiment and to criticize intelligently the recorded results. He wished to acknowledge the enthusiastic co-operation of the group of assistants whose excellent work was responsible for the confidence with which the conclusions could be presented. The following data were given as a supplement to the published paper. Following conclusion of the test work described in the paper, the size of the balls fed to the mill was changed from 3-in. diameter to 2Yz-in. Within a short time, a gradual rise in the tonnage rate took place and, as no other condition had been changed, the increased tonnage was credited to the changed character of the ball load. At present, the average daily tonnage for the mill with low discharge is 1,507 tons, an increase of 77 tons over the 1,430 tons ground when feeding a 3-in. ball. A similar increase in tonnage should be credited to the high-discharge test, if the 2;Y2-in. ball had been used at that time. This would raise the 1,117 tons ground at that time to a new figure of 1,177 tons. From a study made to determine those factors influencing the rate of pulp flow through the low-discharge mill, it became evident that the ball screen used on the high-discharge mill must have been restricting the flow through the mill, although this was not recognized at the time. Accord-ingly, it was decided to repeat the high-discharge run. Additional length was added to the 21-in. ring grizzly originally used, and the length of the reverse spiral was increased. The end of the grizzly was left open so that, if necessary, excess pulp might flow out. A coarse mesh 3 ft. by 3 ft. flat screen was provided to catch stray balls.

Jan 1, 1937

By Joey R. Kish, Shooka Mahboubi, Hatem S. Zurob, Gianluigi A. Botton

The kinetics of the Cr2O3-based scale oxidation and volatilization were studied in the presence of water vapour (H2O). A commercial Cr2O3-based scale forming Type 310S stainless steel was examined at the ambient pressure (0.1 MPa) and 550ºC in relatively low and high H2O containing environments of air- 10% H2O and air- 70% H2O, respectively. The increase in the partial pressure of H2O (pH2O) from 10% to 70% resulted in transition of the oxidation and volatilization kinetics from the parabolic rate law for air-10% H2O to the paralinear rate law for air-70% H2O. The kinetics transition was attributed to the increase in the Cr loss rate from the base scale after coupons exposure in air- 70% H2O. The significant role of the Mn alloying element in the base scale protectiveness was also discussed in the context of the Cr2O3-based scale stability.

Jan 1, 2017

By P. Hansman

"Place Dome Canada's Detour Lake Mine is a low-grade gold producer located in northeastern Ontario. Production is targeted for 2850 tonnes of ore per day. As reserves and mining areas continued to be found below and far to the west of the shaft (Fig. 1), it became necessary to review and upgrade the materials handling facilities. This paper deals with the selection, design and construction of an underground crusher and conveyor system capable of handling up to 450 tonnes per hour from the lowest existing level in the mine.BackgroundThe Detour Lake mine site is accessed via secondary Highway 652 which runs northeast out of Cochrane, Ontario. The road consists of 200 Ian of hard top followed by 100 Ian of well maintained gravel to the mine site. A 1500 m airstrip is maintained at the mine site for emergency use. Prior to 1991, the workforce was flown to and from the mine site. Crews were now bused to the site from Timmins. Remnants of a winter road exist to the southeast which at one time ended in La Sarre, Quebec. This was the route used to haul bulk items during the construction period and early production years.A town site has not been established at the site for the current operations. Instead, a rotational scheme is being utilized whereby most personnel will work seven days on site followed by seven days off site. For some employees, however, the work week is termed as a four/three schedule where they work 42 hours between Monday at 10:00 a.m. and Thursday at 4:00 p.m. with the following three days off. All surface employees and maintenance employees underground work 12-hour shifts. All underground employees work a lOV2-hour shift. Supervisors work a similar schedule as their crews, however, other staff may overlap their rotation during the week.A five-compartment shaft was sunk in 1984 from surface to the 610 m elevation. Shaft stations were established at the 120 m, 260 m, 360 m, 460 m, and 560 m levels. The cage compartment consists of a single deck, 4O-man cage in balance with a counterweight. The cage hoist is an Ingersoll-Rand 10H and is regulated to travel at 4.1 m/s. Two 9 t skips operate in balance at a travel speed of 7.1 mls. The skip hoist is a 3.05 m drum Nordberg. Both hoists are automated to function without a hoistman during normal skipping and cage service runs."

Jan 1, 1995

By D. A. Rhys

"The Red Bluff porphyry is a tabular 2 km long north-west trending Early Jurassic quartz diorite to monzodiorite body that intrudes a folded Triassic greywacke sequence in the lskut River area, northwestern British Columbia. The porphyry is 500 m to 800 m northeast of the Snip orebody, which is a southwest-dipping shear-vein, termed the Twin zone that contains approximately 35 tonnes of gold.The intrusion associated with the mineralization is characterized by 0.3 cm to 4 cm phenocrysts of K-feldspar in a mediumgrained plagioclase porphyritic matrix. It is overprinted by pervasive sericite + quartz ± K-feldspar ± biotite (potassic) alteration characterized by intense stockworking of quartz veins containing magnetite--hematite bands. This assemblage is cut successively by quartz veins with minor iron-oxides and pyrite, and by younger pyrite veins with phyllic envelopes. The system is gold-rich but copper-poor, with typical grades between 0.25 g/t and 0.6 g/t Au, and 0.1% and 0.2% Cu. All styles of alteration and veining have similar abundances of these metals. Where southwest- and north-east dipping shear zones are developed in the porphyry, veins of all types are sheeted and foliation parallel. These sheeted zones are interpreted to be syntectonic. Asymmetric phenocrysts, folded veins and oblique foliations developed in the 130 haulageway of the Snip mine imply oblique normally-directed shear on the southwest-dipping foliation.The adjacent Twin zone is a high-grade auriferous shear-vein system that is internally banded with: (1) carbonate-chlorite-biotite veins, with textures indicating formation at least partially by wallrock replacement, and (2) dilatant quartz-sulphide veins. Veins commonly have potassic alteration envelopes that contain biotite ± calcite ± K-feldspar. The zone is highly deformed and schistose, with numerous kinematic indicators including shear bands, asymmetric folds, rotated porphyroclasts and oblique foliations that indicate a normally-directed shear sense which is parallel to that indicated by fabrics within the porphyry.Precious and base metal veins within 2 km or 3 km of the Red Bluff porphyry are zoned. Veins and shear-veins proximal to the intrusion, such as the Twin zone, are typically enriched in gold, copper and molybdenum, and have potassic alteration envelopes dominated by biotite. Distal veins usually contain relatively abundant zinc and lead and have sericitic alteration envelopes. Structures of both types have an Early Jurassic galena Pb-Pb isotope signature.The similarities in structural fabrics and alteration histories in both the Twin zone and the porphyry, the zoning of the vein systems in the area, and the apparently concordant Early Jurassic zircon U-Pb age from the porphyry and galena Pb-Pb dates from the Twin zone and surrounding vein systems suggest that intrusion, semi-brittle deformation and a large mineralizing hydrothermal system were closely related temporally and genetically."

Jan 1, 1995

By Krishna Parameswaran

In this paper, we attempt to answer an often asked question, how can metal mining be compatible with the principles of sustainable development. Starting with the classic Brundtland Commission definition of sustainable development as "development that meets the needs of the present without compromising the ability of future generations to meet their own needs," we make the case that mining is or should be sustainable, using examples of sustainable practices at ASARCO LLC, an integrated U.S primary copper producer. These examples cover the entire mining cycle starting with exploration, mining, beneficiation, smelting, refining, closure and post-closure and post-mining land use. It is hoped that the presentation will challenge the mining industry to even greater innovation as future mineral development projects are planned.

Jan 1, 2015

By R. M. de Carvalho

Empirical and phenomenological models of SAG and AG mills have dominated the scene for the last few decades, being used nearly every time a mill is scale-up or an attempt is made to improve its performance. However, in spite of their success, these models fail to describe the details of both the grinding environment and the breakage mechanisms. The result is a generally good track record, with a few ? but very important ? instances when these models fall short in their predictions, which can be very costly. Further, nearly all of these models require detailed calibration to industrial and pilot plant data, being costly in their application, although still with limited predictive capabilities. Recognizing these challenges, a new model framework has been proposed which overcomes the limitations of currently used models by coupling the microscale population balance model, the discrete element model and functions that describe internal classification at the mill grate. This model framework has already been applied to describe breakage in ball mills, with showing very promising results. However, in the case of SAG and AG mills a much greater level of complexity is involved in the model, given the interaction between the mechanical environment that is formed totally or, in part, by the ore itself, and the breakage response in the mill. The paper describes the model framework, demonstrating how it can address appropriately effects such as mill speed, mill filling and size distribution, on the response from the mill. Some of the advantages of the model are related to its intrinsic multi-component and dynamic nature, which allows simulating appropriately mixtures of ores of different competences in a transient manner.

Jan 1, 2012

By S. F. Featherby

"This paper traces briefly the historical development of coal handling systems to meet the needs of a rapidly developing thermal power generation technology. The wide range of operating requirements is demonstrated by comparing and contrasting the Wabamun GS of Calgary Power Ltd. and a typical modern Ontario-Hydro thermal plant. The problems of safe storage of large tonnages of coal in stockpiles are discussed, together with recommendations for stockpile management. The development of coal bunkers and their management is discussed in detail, together with future trends in the industry."

Jan 1, 1966

By J. Ambrose, R. W. Zimmerman

"Shales are highly anisotropic in their mechanical behavior. The strength ( ??1) of anisotropic shales depends not only on the magnitude of the other two principal stresses ( ??2, ??3), but also on the bedding plane orientations (?) relative to the principal stresses. In this study, the role of the intermediate stress ( ??2) on the strength of shale is evaluated using new data from triaxial compression and extension tests. To understand the failure behavior of shales, we have carried out triaxial compression tests ( ??1 > ??2 = ??3) on two organic rich mudstones, at different confining stresses and loading angles. We first fit the triaxial compression data with Jaeger’s plane-of-weakness model, and find that the model is able to represent the strength behavior of anisotropic shales reasonably well. We then carried out five triaxial extension tests ( ??1 = ??2 > ??3) for a high strength-anisotropy shale, and two extension tests for a low strength-anisotropy shale. Results from the compression and extension tests for failure along the weak plane shows that the role of ??2 is not significant for weak plane failure. However, for the low strength-anisotropy shale, the failure strength of the intact rock (i.e., at ??= 0o and 90o) for compression and extension tests were significantly different. This indicates that for intact rock failure, the role of ??2 is important and cannot be ignored.INTRODUCTIONFor many years, various researchers have studied the roles of ??2 for failure of isotropic rocks. (Mogi, 1967 and 2007; Colmenares and Zoback, 2002; Al-Ajmi and Zimmerman, 2005 and 2006; Haimson, 2009; Ma and Haimson, 2012). The findings from these studies show that the effect of ??2 on the strength of isotropic rocks is generally significant, and cannot be ignored.Since the role of ??2 in the failure of isotropic rocks was recognized, other researchers attempted to extend some of these isotropic failure criteria to anisotropic rocks, but with limited success (e.g., Tiwari & Rao, 2007; Singh et al., 1998; Zhang and Zhu, 2007; Pei, 2008). Smith and Cheatham (1980), on the other hand, conducted true-triaxial experiments on the Green River Shale and used a J2-I1 type relationship to predict the strength behavior, but without considering the effect of the three-dimensional orientation of the weak plane on strength. Therefore, unlike for the case of isotropic rocks, additional studies need to be done to determine the role of 2 on the failure of anisotropic rocks."

Jan 1, 2015

By G. J. Simandl

"Since the 1980s, China has become the predominant producer of REEs. Recently, it introduced REE export quotas and this started a world-scale REE exploration rush. REE resources are concentrated in carbonatite-related deposits, peralkaline igneous rocks, pegmatites, REE ± P veins, ion adsorption clays, placers, and some deep ocean sediments. REEs could also be derived as a by-product of phosphate fertilizer, U processing, Ti-Zr-bearing placers, and exploitation of Olympic Dam-type sub-type of IOCG deposits. The ideal REE development target would be located in a politically stable jurisdiction such as Canada. REE grade and tonnage, mineralogy, and permissive metallurgy are some of the key technical factors that could be used to screen projects. INTRODUCTIONAccording to the International Union of Pure and Applied Chemistry (IUPAC), the term “rare earth elements” (REEs) encompasses yttrium (Y), scandium (Sc), and the lanthanide series: lanthanum (La), cerium (Ce), praseodymium (Pr), neodymium (Nd), promethium (Pm), samarium (Sm), europium (Eu), gadolinium (Gd), terbium (Tb), dysprosium (Dy), holmium (Ho), erbium (Er), thulium (Tm), ytterbium (Yb), and lutetium (Lu). This definition is used throughout this paper.REEs are subdivided into light (LREE) and heavy (HREE) categories. LREEs include, Sc, La, Ce, Pr, Nd, Sm, Eu, and Gd and HREE include Tb, Dy, Ho, Er, Tm, Yb, Lu, and Y. Promethium (Pm) does not occur in nature. Concentrations of individual LREEs in the upper crust of the Earth are comparable to those of base metals. Even the least abundant REE (Lu) is about 200 times more abundant than gold.The production of REEs, reported in the form of oxides (REOs), for 2011 is estimated at 140 000 t (Figure 1a). Although high technology industries can substitute several REEs with other materials, these substitutes are typically more expensive or less effective than the REEs they replace. A number of countries, including the United States, consider several REEs essential for national security, their economy, and a general reduction in green house gas emissions. The forecasted demand for individual LREOs is much higher than that of HREOs (Figure 2). Dy, Eu, Tb, Nd, and Y are essential for the US economy and subject to predicted supply disruptions (U.S. Department of Energy, 2010)."

Jan 1, 2012

By D. W. Davis, P. Landais, L. J. Robb

Abstract -Nodules of carbonaceous matter have been observed in several Archaean peraluminous granites adjoining the gold- and uranium-bearing Witwatersrand Basin. These nodules, which resemble solid bitumen, usually replace uraninite or uranothorite and are paragenetically late. They show many similarities to kerogen seams and nodules associated with the conglomerate horizons in the Witwatersrand Basin, including composition, maturation, intimate association with uraninite, and a late paragenesis. U-Pb isotope ratios for granite-hosted and Witwatersrand kerogens define a single, albeit somewhat diffuse, Pb-loss discordia suggesting an upper intercept age of circa 2300 Ma. Carbon isotope analysis indicates lighter ?13C values for the granite-hosted nodules than for the sediment-hosted kerogen seams. Raman spectroscopy indicates that granite-hosted kerogen is more highly ordered than Witwatersrand seam kerogen. A model is presented which links the granitoid­ and sediment-hosted organic matter to an event of oil generation in the Witwatersrand Basin circa 2300 Ma ago. Light hydrocarbons migrated through the sediments and into underlying/adjacent granitic rocks, undergoing polymerization and accumulation in response to radiation accompanying the presence of high-uranium phases.

Jan 1, 1994

By J. D. Clucas, N. Verbaan, T. Grammatikopoulos, D. B. Dreisinger, C. Forstner, M. Aghamirian

"Search Minerals is currently exploring the Port Hope Simpson (PHS) Rare Earth Element District in southeastern Labrador, Canada. The Foxtrot Rare Earth Element (REE) Project in the PHS District has a 43-101 resource estimate consisting of 3,410,000 tonnes of Indicated Mineral Resources and 5,850,000 tonnes of Inferred Mineral Resources. The indicated and inferred resources contain 1.07% and 0.98% total rare earth element oxide (including yttrium), respectively. The dysprosium and neodymium grades are particularly attractive at 218 ppm Dy2O3 and 1687 ppm Nd2O3 for the indicated resources and 208 ppm Dy2O3 and 1494 ppm Nd2O3 for the inferred resources. The mineralization remains open along strike and at depth and is only one of a number of attractive exploration targets in the Port Hope Simpson area. The REE minerals fergusonite and allanite are present. The ore can be beneficiated by gravity, magnetic separation and flotation to a recovery of +80% for the individual REE. Acid bake and water leaching may be used to extract REE into solution for subsequent purification and recovery. The extraction range for single stage leach tests were 91-96% for Nd, 84-87% for Tm and 92-94 % for Dy with modest acid consumptions. INTRODUCTIONSearch Minerals Inc. (Search) is exploring the 100% owned Port Hope - Simpson District in Labrador, Canada for rare earth elements (REE). This District is approximately 135 km by 12 km in size, and is highly prospective for heavy and light rare earth elements. A total of 11 REE prospects have been discovered in the District to date, including the Foxtrot. In addition, Search is exploring in the 100% owned Henley Harbour region and has joint ventures with Quest Rare Minerals in the Strange Lake region, and with Great Western Minerals Group in the Red Wine complex, all in Labrador. These exploration locations are illustrated in the Figure 1. The focus of this paper is the investigation of the mineralogy and processing of Foxtrot REE materials. The Foxtrot resource falls within the claims held by Search in the Port Hope Simpson REE District. The infrastructure available at Foxtrot is excellent with a deep water port, air strip and road and power infrastructure at Port Hope Simpson. Over $7 Million has been spent to date on exploration and development of the District. The Foxtrot has been explored using prospecting geochemical methods, geophysics (airborne and ground), channel sampling of surface outcrops, mapping and three phases of drilling (18,934 m total)."

Jan 1, 2012