Search Documents

By G. J. Hutchins

Precision surface mining is gaining traction in the iron ore, copper, iodine, limestone, bauxite, coal and gypsum markets. In this paper, we first address the possible improvements of a surface miner control using GPS techniques. An application in an iron ore mine in Western Australia is presented. The second item addressed is improvements of a new drum driving technique for a 100 ton surface miner. This technique involves installing a slow speed hydrostatic motor directly on the cutting drum rather than driving the drum through chain and sprockets. Details of the performance of this direct-drive versus the chain-drive are detailed. In addition to the 100 ton machine, we also present a 200 ton surface miner. This larger machine has 1600 hp (894.8 kg), and has been successfully introduced into a large iron ore mine in Western Australia. Performance of the 200 ton surface mining machine in various rock hardnesses is detailed. Some comments on the cost effectiveness of using a built-in loader versus loading with wheel loaders are included.

Aug 1, 2013

By M. R. P. Snow

"This paper outlines geotechnical conditions that commonly exist in underground, hardrock mines and the challenges posed for ground-support steel, specifically rockbolts, used in these environments. A model is proposed whereby the in-situ stress and rock-mass classifications (based on Bieniawski’s rock mass rating) form the basis of determining the desired steel properties of the rockbolts used. Based on the ASTM F432 bolting specification, recommended minimum steel properties are defined for three ranges of in-situ stress levels, each with their own six ranges of RMR values. Heat treatment for the steel can be specified once these minimum steel properties are known.RÉSUMÉ Le présent article décrit les conditions géotechniques qui existent fréquemment dans les mines souterraines de roches dures et les défis que cela pose pour le soutien de terrain en acier, plus spécifiquement les boulons d’ancrage utilisés dans ces environnements. Un modèle est proposé dans lequel les contraintes in situ et les classifications de la masse rocheuse (selon la classification de la masse rocheuse de Bieniawski) servent de base pour la détermination des propriétés désirées pour l’acier des boulons d’ancrage utilisés. En se basant sur les spécifications de boulonnage de l’ASTM F432, les propriétés minimales recommandées pour l’acier sont définies pour trois plages de niveaux de contraintes in situ, chacune avec sa propre plage de six valeurs de classification de la masse rocheuse (RMR). Un traitement thermique pour l’acier peut être spécifié une fois que ces propriétés minimales pour l’acier sont connues."

Jan 1, 2016

By K. Swedburg, M. Samuels

"The expansion of the concentrator at New Gold’s New Afton copper-gold mine in British Columbia, Canada, completed in 2015, included an increase in the required retention time of the cleaning circuit. On site pilot testing of a Woodgrove Staged Flotation Reactor (SFR) had shown that a high grade copper concentrate would be produced with excellent recovery. The SFR was selected rather than conventional tank cell technology based on the much smaller footprint (which rendered a separate and expensive building extension unnecessary), high concentrate grades demonstrated in testing, and the lower energy requirement. Three SFRs, each capable of taking a nominal feed of 700 cubic meters per hour were installed and commissioned 10 months after the receipt of order. The SFRs operate in series and all of the cells produce a final concentrate typically grading 32% Cu, while the overall SFR stage recovery averages 55%. The tailings from the SFRs are treated in the original conventional three-stage cleaner circuit where the remaining values are recovered in a concentrate grading 28% Cu. Design production was achieved within days of the initial start-up of the SFR circuit.INTRODUCTIONThe New Afton concentrator, located near Kamloops, British Columbia, Canada processes a copper-gold ore with a designed head grade of 0.96% Cu, 0.72 g/tonne Au, and 2.22 g/t Ag.The New Afton Mine is a block cave mining operation. Ore is undercut from the bottom up and removed at the extraction level from a grid of draw points. Ore is trammed to the ore passes by underground loader and dropped to a haulage level for transport by trucks to the gyratory crusher. From the crusher, the ore is conveyed to the mill via a 4.5 kilometre long conveyor system. Block caving was chosen for the New Afton deposit because the underground infrastructure could be built below the historical open pit of the Afton Mine (a previous operation of Teck Resources) and this method is favorable to large-scale low-cost mining.The New Afton deposit is a copper-gold, alkalic porphyry system. Hypogene mineralization is characterized by discontinuous copper sulphide veinlets and disseminations, principally chalcopyrite and minor bornite, along with pyrite as the second most dominant sulphide. Gold particles vary in size from 5 µm to 40 µm and occur as native gold and electrum, associated mostly with the chalcopyrite grains and never with the pyrite. In some instances, a second alteration phase has resulted in the copper sulphides being replaced by tennantite-tetrahedrite locally and along faults that transect the mineralized body. The design head grade of arsenic is 244 PPM, although the presence of tennantite is inconsistent and can vary from trace levels to 15% of the total copper. No arsenopyrite is present in the hypogene ores. Supergene mineralization, consisting of native copper with accessory chalcocite occurs in minor amounts along faults and highly oxidized near-surface portions of the deposit."

Jan 1, 2016

By John A. Herbst, Gerald H. Luttrell, Jaisen N. Kohmuench, Aaron Noble, Michael J. Mankosa

The HydroFloat TM is an innovative fluidized-bed separator that can substantially increase the upper particle size that can be successfully treated by flotation. Recent studies conducted using laboratory, bench-scale and pilot-scale equipment indicate that this technology can be used to float coarse sulfide middlings that cannot be recovered by conventional flotation machines. Recent data collected from pilotscale tests conducted at a base metal concentrator indicate that this technology can float middlings particles as large as 850 microns in diameter containing as little as 1% exposed hydrophobic mineral. As such, the crossover of this technology into the base metals industry has the potential to substantially reduce grinding costs and increase concentrator recovery/capacity through the use of split-feed circuitry. The split-feed concept, which is often used for upgrading industrial minerals, involves segregation of the feed into more than one size class followed by subsequent upgrading using mills/separators/reagents specifically optimized for each size class. In this article, a split-feed circuit is described that utilizes two stages of classifying cyclones in conjunction with the HydroFloat_ separator. The circuit is designed to recover, recycle and regrind coarse middlings containing small amounts of valuable mineral while simultaneously rejecting coarse well-liberated siliceous gangue so that mill throughput can be increased. Simulation data conducted using well-known process models suggest that this approach can increase existing primary mill capacity by up to 25% with only modest investments in new classifying and flotation equipment.

Jan 1, 2016

By R. C. Beard

"The Ontario Ministry of Natural Resources has recently initiated several incentive programs to encourage and facilitate the development of new mines in northwestern Ontario. Some are privatized out to consultants and contractors. The status of three of these programs will be reviewed in this paper.IntroductionOne of the main objectives of the Mineral Resources Group of the Ontario Ministry of Natural Resources is to encourage and assist mineral exploration and the development of new mines in the Province. Programs to accomplish this objective are largely carried out through two Branches in the main office (in Toronto), the Mineral Resources Branch and the Ontario Geological Survey, and also a number of regional field offices scattered across Ontario.The function of the Mineral Resources Branch is to identify and administer effective policies that will ensure maximum benefits to the Province from mineral resource extraction.One of the most important factors in ensuring effective exploration in the Province is the availability of a good geosciences data base from which to work. It is the responsibility of the Ontario Geological Survey to develop and continually update this data base, providing, to both the public and private sector, an inventory and analysis of the geology and mineral deposits of the Province.The main functions of the regional field offices are to provide technical data and advice to exploration companies and prospectors, to encourage and assist exploration, and to provide information and general assistance to producing and developing properties to facilitate resource development and extraction. This is accomplished through the offices of the mineral resource coordinators and resident geologists. In northwestern Ontario, these field offices are located at Thunder Bay, Kenora, Red Lake and Sioux Lookout.To accomplish their objectives, the Ontario Geological Survey and the regional field offices carry out regular, ongoing geoscience and other mineral resource programs, under their base funding."

Jan 1, 1982

By A. Bois-Brochu, G. Morin, G. Marin, M. C. Parr, J. Carignan

The presence of an alpha case on titanium parts produced by investment casting is problematic and has to be eliminated. The traditional techniques for the evaluation of its thickness are metallographic measurements and micro-hardness profiles. To obtain a better understanding of how the alpha case is formed with the underlying objective of limiting its depth, the present study proposes to characterize the microstructure and the chemical composition of the alpha case. Electron microprobe analyzer (EMPA) linescans were used to quantify the oxygen and substitutional elements that come from the mould and promote the alpha case formation. The chemical profiles were correlated with metallographic and microhardness measurements. For microstructure, optical microscopy (etched and polarized light analysis) was used. For phase analysis, samples were mechanically polished step by step and analysed using X-ray diffraction and optical microscopy. Furthermore, surface analysis techniques such as XPS and Auger Microscopy were evaluated but results were found to be inconclusive because the formation of the oxide layer was faster than its ablation and the matrix could thus not be analysed. The alpha case was observed on a Ti-6Al-4V step block casting.

Jan 1, 2014

By Gabriel Voicu, Marc Bardoux, Ross Stevenson, Nuno Machado, Jean Lafrance

"Abstract - Paleoproterozoic gold is found in two different volcano-sedimentary sequences and intrusive bodies separated by 600 km within the Guiana Shield. The 2148 Ma St-Élie granite intruded volcanic-arc sequences of the Paramaca Group, whereas the 2096 Ma Omai stock penetrated backarc/ island-arc sequences of the Barama-Mazaruni Group. Positive ?Nd values suggest that both suites lack Archean crustal contaminants, which is consistent with an origin in an oceanic arc setting.The St-Élie deposit is characterized by quartz-dominant vein systems with minor metallic minerals, represented chiefly by pyrrhotite and pyrite. Biotite, calcite, and chlorite are the main gangue minerals. The alteration haloes at St-Élie feature a strong potassic zone, which is absent at Omai. The ore-controlling structures are ductile and the vein emplacement is related mainly to contemporaneous, high-angle ductile shear zones. The St-Élie deposit formed at temperatures >350°C. The stable isotopes values are compatible with a magmatic or metamorphic source.The Omai deposit is characterized by quartz-dominant vein systems with minor metallic minerals, represented mainly by pyrite. Ankerite, scheelite, albite, and chlorite are common gangue minerals. The vein emplacement is syn- to post-deformation and it is related mainly to brittle shear zones with low-angle, stockwork networks and breccia zones. The Omai deposit formed in a temperature range between 250°C and 170°C, much lower than the St-Élie deposit. The stable isotope values are compatible with mixing between deep-seated fluids of metamorphic or magmatic origin with surface- derived fluids.These differences between St-Élie and Omai are interpreted in terms of their depth of formation. Alteration patterns, structural elements, and paragenetic assemblages indicate that the gold at St-Élie was most probably emplaced at a mesozonal depth, whereas the Omai setting yields evidence for epizonal conditions."

Jan 1, 1999

By A. A. Ruitenberg, S. C. Johnson, L. R. Fyffe

"Several types of stratiform and epigenetic gold deposits have been found in New Brunswick, It is the purpose of this paper to describe and classify the epigenetic deposits and demonstrate their relationship to tectonic evolution. The stratiform deposits are mostly volcanogenic massive sulphide deposits that are described elsewhere (Davies et al., 1985).The auriferous epigenetic deposits include quartz-carbonate veins and stockworks, polymetallic veins, contact metasomatic, porphyry copper and volcanic breccia (epithermal) deposits. These epigenetic deposits are concentrated in major fault zones that define or are close to the boundaries of tectonostratigraphic terranes or terranes and cover sequences. The host rocks of the deposits were subjected to extensive crustal thickening resulting from thrusting and/or high angle reverse faulting.The gold deposits north of the Avalon Terrane occur indilatent structures related to mainly dextral wrench faulting that postdated the episode of crustal thickening. The deposits along the southern margin of the Avalon Terrane occur in structures related to late phase thrusting."

Jan 1, 1990

By Bradford P. Simser

Increasingly sophisticated rock mechanic tools are becoming more and more available for today?s ground control specialist. However many problems are still beyond our ability to explicitly calculate or measure. There is often a gap between the ?art? and the ?science? of rock mechanics. This paper focuses more on the ?art?, giving relatively simple examples of underground observations and micro-seismic records to help explain ground control issues. Ground support techniques such as in cycle shotcrete with high pressure water scaling, mesh and bolting, pumpable resin bolts/cablebolting, and yielding bolts with load spreading straps are discussed. The use of primary/secondary type blasthole sequences in moderate to high stress situations is also discussed with several examples of the micro-seismic response to the stoping. Relatively erratic geology with high material strength contrasts is currently being mined with blasthole methods at Nickel Rim South. Although the mine is still in its? ?early? days, over 1 million tonnes has been extracted and some empirical experience is highlighted with potential longer term issues also being discussed.

Oct 1, 2010

By S. Hon, C. Searcy, R. DasGupta, B. Fleet, A. Davidse, A. Pringle

"The mining industry is facing serious long- and short-term challenges relating to uncertain commodity prices, environmental pressures, and margin compression due to rising energy costs. Energy issues, formerly treated as an operating cost, are changing as executives search for longer term solutions to deal with uncertain fossil fuel prices and greenhouse gas emissions. Consequently, mining executives are increasingly willing to consider introducing a proportion of renewable energy (RE) systems into the mine energy mix. This paper examines how RE can be successfully integrated at mine sites, as well as some of the benefits and barriers to their wider adoption.RÉSUMÉ L’industrie minière fait face à de sérieux défis, à long et à court terme, en raison de l’incertitude des prix des matières premières, des pressions environnementales et des compressions de la marge bénéficiaire dues à la hausse des coûts de l’énergie. Les questions énergétiques, auparavant considérées comme un coût d’exploitation, changent alors que les cadres cherchent des solutions à plus long terme afin de prendre des mesures pour contrer les prix incertains des combustibles fossiles et les émissions des gaz à effet de serre. C’est pourquoi les cadres miniers sont de plus en plus disposés à considérer l’introduction d’une proportion de systèmes d’énergie renouvelable dans l’équation énergétique de la mine. Le présent article traite de la manière dont les énergies renouvelables peuvent être introduites avec succès aux sites miniers ainsi que quelques-uns des avantages et des barrières à leur application à une plus grande échelle."

Jan 1, 2015

By L. E. Gutiérrez

A new filtration model based on porous media transport theory is presented. It predicts capacity and final moisture content in the filtered cake as a function of design and operational variables at the plant. FilterSim® is the computer code where this new model is programmed. Application of FilterSim® to ten-month operation of an industrial copper concentrate filtration plant is shown on a daily basis and using a single set of internal parameters for the whole period. Average error is less than 5%, both in capacity and moisture estimation. FilterSim® abilities to optimize industrial filtration plants as well as to estimate future budgets are illustrated with several real examples.

Jan 1, 2007

By A. Dave Mackintosh

The Current demand for potash has pushed world prices to record levels and allowed Saskatchewan producers to operate at maximum capacity. Several years of strong demand has resulted in a permitting rush not seen since the 1960?s. Even though Saskatchewan has a huge potash resource, mining and processing constraints will limit the areas of economic development. Introduction In 1969 M. E. Holter prepared a report ?The Middle Devonian Prairie Evaporite of Saskatchewan?, published by the then Dept. of Mineral Resources. Holter?s report has remained the bible of geologists working in potash ever since. It is astounding that a report written before there was really much potash mining history in the province, is as valid today as when it was first published. This paper re-iterates much of Holter?s report and adds a little mining experience to essentially confirm the importance of his work.

May 1, 2008

By D. J. MacKinnon

"The Canadian Copper Company, formed in 1885, began mining the nickel-copper ores of Sudbury in 1887 and producing nickel-copper matte from its smelter in 1888(1). Although it was quickly appreciated that the separation of nickel and copper (i.e. refining) was critical to the production of a marketable nickel product, refined nickel was not produced in Canada until about 1918. From the beginning of the industry, there was considerable political agitation to refine nickel in the Province of Ontario(2). The companies, however, claimed that the existing processes, viz. the sodium sulphide ""tops and bottoms"" process operated by the Orford Copper Company of New Jersey, U.S.A.(1,3,4) and the carbonyl process(5,6) developed by the Mond Company at Clydach, Wales, were too costly to operate in Canada. Nickel was first refined in Ontario about 1918 when the International Nickel Company opened a nickel refinery at Port Colborne, Ontario(6). Initially, however, the refinery at Port Colborne employed the Orford sodium sulphide process, and the first electrorefined nickel in Canada was produced in 1920 by the British America Nickel Corporation whose mine and smelter were located in Sudbury, Ontario, but whose electrorefinery was located at Deschenes, Quebec, near Ottawa, Ontario. The purpose of this article is to outline the early history of nickel electrorefining and to trace the significant developments which led to the first successful commercial electrolytic nickel refinery in Canada. The development of an electrolytic process for refining nickel is due largely to the efforts of four individuals, viz. Carl Hoepfner, Hans A. Frasch, D.H. Browne and ultimately N.V. Hybinette, and the contribution of each is discussed separately below."

Jan 1, 1999

By David Nicholls

?Overview of New Afton ?Reserves and Resources ?Geology and Mineralization ?Exploration ?Capital Project Development to Date ?Mine Development ?Processing ?Construction ?LOM ?Health, Safety, Environment and Social Responsibility Overview of New Afton ?Fully owned by New Gold Inc ?Large gold-copper porphyry deposit, amenable to block cave mining, production commencing in 2012 -1 million ounce gold reserve -1 billion pound copper reserve -Estimated 13 year mine life ?Low operating cost ?Estimated capital expenditure requirements -Spend to date ?US$200million -Remaining to be spent ?US$400milllion ?Robust economics ?Excellent location and infrastructure ?Significant cash flow contributor for the Company

May 1, 2010

By G. R. C. Pacheco, D. M. Fonseca, R. Neuböck, G. E. Gonçalves, W. Moulin-Silva

Degradation by sulfur gases is an important lining wear mechanism in the copper industry. SO2/SO3 gases infiltrate into the pores of the basic refractory bricks, combine with their raw materials through expansive reactions and significantly modify the bricks’ structure. This study presents a comparison of the corrosion resistance against sulfur attack of different magnesia-based refractories using a simple, low-cost and quantitative method. Recipes containing sintered MgO grains showed lower resistance to corrosion by sulfur oxides compared to basic grades containing fused grains. Chromium corundum grades were used as a reference and showed very good resistance to this corrosion mechanism under the test conditions. The novel test provided relevant results that agree with what is commonly observed during operation and in previous post-mortem studies. This tool could be very useful in selecting refractory grades for the copper industry and predicting their performance. INTRODUCTION Oxidation of matte sulfides during copper production leads to the formation of sulfur oxides, which infiltrate into the pores of the refractory lining and react with the basic oxides below 1000°C to form magnesium and calcium sulfates. This reaction is accompanied by an expressive volume increase, consequent densification of the refractory microstructure and weakening of the brick bond (Malfliet et al., 2013). Thus, corrosion by SO2/SO3 is an important wear mechanism in the non-ferrous industry and the resistance to this compound should be considered when defining refractories for this application. Previous studies on this matter include expensive and complex testing methods involving pressurized SO2 gas cylinders in order to investigate the corrosion resistance of MgO-containing materials by sulfur oxides (Gerle & Podwórny et al., 2016; Fotoyi & Eric, 2011; Fotoyi, 2009; Podwórny & Piotrowski et al., 2008). The current study was based on a test developed by Pacheco & Fonseca (2018) to assess alkali infiltration and aims to provide an evaluation method of the corrosion resistance of refractories by SO2/SO3 in a simple and quantitative manner. This novel test is useful to compare the corrosion resistance of different refractory recipes and properly select the grades that should be employed in the non-ferrous industry. A case study is provided to illustrate the damage caused by sulfur oxides in refractory linings.

Jan 1, 2019

By Brian Hall

For some years, the mining industry has been consistently delivering returns below the market average. One of the causes is a disconnect between what is perceived to drive value creation by many industry analysts and senior corporate executives, and what actually drives the intrinsic value of mining operations. The perverse effect is that strategies that should increase value are perceived to have the potential to drive share prices down, and vice versa. This paper challenges common perceptions of what drives a mining company?s value. Anecdotal evidence suggests that the key drivers of value in the market, and hence in many boardrooms, are such things as increasing the reserves and production rate, and reducing unit operating cost. However, while the quoted reserves may satisfy ore reserves reporting code requirements to be economic, this does not imply that they are optimal. Often, a proportion of the quoted reserve reduces the potential value of the operation. Metal price increases, increased production rates, and operating cost reductions are all seen as conditions or actions that can improve value, and lead to cutoff grade reductions, thereby increasing ore reserves. However, modern cutoff theory and studies conducted by the author and his colleagues show clearly that, while breakeven cutoff grades will fall in these circumstances, optimum cutoffs may be much less volatile, and may even increase. Results from case studies indicate that value is maximised by right-sizing, not maximising, the production capacities, and by optimising the cutoff strategy. Values of many existing underground mining operations can be increased significantly by a substantial cutoff grade increase. Also, an increase in downside risk, and hence reduced returns, can occur using typical life-of-mine planning strategies if prices received are lower than predicted. Since this is often the case, low industry returns may be a direct result of typical strategic mine planning processes. Relatively simple cost-effective techniques are available to provide senior decision makers with information needed to assess the tradeoffs between their many conflicting corporate goals, and the balance between risk and reward. Often this information is not being generated at all. If it is, decisions affecting the value of the company are occurring by default at relatively low levels within the hierarchy, with senior executives apparently unaware of them or their potential impact. The paper concludes that without a re-evaluation of the way mining projects are valued, to demand proven value optimisation from mining plans by boards and mining analysts, the industry will continue to deliver below average returns.

May 1, 2003

By J. Y. Liu

In Comparison to the application of HPGR (high-pressure grinding rolls) in the cement industry and in iron ore processing, the introduction of this energy-efficient comminution technology to processing of nonferrous base-metal ores has progressed slowly as yet. In the field of minerals industry, challenges lies not only in the large variety of the feed material with respect to particle size, density, hardness, moisture and mineralogy of the material but also in complexity of the processing flowsheet, which need to be addressed from case to case based on result of HPGR comminution test work. Whereas conventional comminution test with HPGR in lab-scale or pilot scale needs quite a large amount of feed material, a compressive stressing test of particle-bed in piston-die device provides an effective way to study interparticle breakage behavior of ore material with much less feed. In the present study the effects of interparticle breakage on comminution of a copper ore has been investigated by compressive stressing of particle bed in a piston-die device. The feeds to the particle-bed stressing tests were four narrow size fractions in the size range of 0.3~3.35 mm and a broad size fraction of 0/3.35 mm. The pressures applied were in the range between 30 and 180 MPa. The results showed that the specific energy consumption increases linearly with the pressure; the product fineness increases also with the pressure, but the magnitude of this increase declines as the pressure goes up. Under the same stressing intensity, the product size distribution curve becomes steeper as the particle size decreases, so there is no self-similarity between product size distributions of different feed sizes. The suitability of a material-characterization model for interparticle breakage was verified for this ore. In addition, the effect of interparticle breakage on comminution of this ore with respect to its influence on the downstream flotation were analyzed in terms of size-metal distribution and mineral liberation.

Jan 1, 2016

By Michael DeLallo

Clean Coal Technology (CCT) ?Technologies designed to enhance both the efficiency and the environmental acceptability of coal extraction, preparation and use?. These technologies reduce emissions, reduce wastes, and increase the amount of energy gained form each ton of coal extracted and converted into energy. ?? Carbon Capture and Sequestration are an integral part of CCT either as constructed or on a future retrofit basis.

May 1, 2008

By Karl J. C. Harries

"2.1. INTRODUCTIONNo agreement can be perfect in the sense that it contemplates and provides for all eventualities. Mineral acquisition agreements are usually negotiated and drafted at a time when an orebody is no more than a gleam in a geologist’s eye, so it is hardly possible to provide for development and operation in other than the most general terms. However, an agreement that stops short of contemplating the possibility of an orebody and production is ill-advised. Accordingly, it is important to provide procedures to make decisions that will let the project proceed, even in the face of a fallingout between parties. Whether the parties are shareholders in a corporation or venturers in a contractual common undertaking like a joint venture, differences of opinion and disputes will occur. Unfortunately, more and more are ending up before the courts. Besides greed and the growing tendency in society to fight rather than talk, there are other factors that contribute to the increase of litigation. In some jurisdictions, agreements have tended to become complicated, often defying interpretation, even by a lawyer, and explorationists want their budgets to go into the ground as constructive work rather than into a lawyer’s pocket. All this has led to a growing tendency for corporations to take the attitude that the chances of finding a mine are, at best, marginal and there are lots of earlier agreements in the files to draw from, so why not prepare their own agreements? As discussed in the preceding chapter, this can be folly. All these factors can quickly have parties facing each other in court while a project sits idle. Added to this is the problem that, in some jurisdictions, lawyers may take cases on a contingency-fee basis, sometimes promoting the pursuit of a nebulous claim.When an orebody is discovered, someone will always want some, or more, for himself. There is a breed of “prospectors” who prospect for legal actions, on the somewhat sound grounds that a major corporation will buy off nuisance litigation, rather than incurring the cost and effort of attacking even a poorly founded claim in the courts. They may even find a winner. Besides, it is far more comfortable and relaxing to prospect for problems and legal niceties than to prospect for an orebody.1 In short, it is appropriate to consider briefly some of the factors relating to lawsuits and judgments. Although many of the comments are made in the context of the common law and the Canadian legal system, most of the concepts and suggestions are applicable to any legal system."

Jan 1, 2003

By G. R. Sadowski

"Large subhorizontal joints have been found in the foundation excavations in basalt and granite of Brazilian Dams. Some spread for hundreds of square meters showed slickensides—polished surfaces plus striations—and laminations interpreted as related to shear displacement, what substantially reduced their shear strength and imposed special reinforcement measures against the potential sliding of overlying concrete structures. The geological characteristics of these discontinuities have raised speculations related to their origin, be it related to mechanisms of bulging, cambering or to some tectonic or primary geological event.Several geologists and engineers from the northern hemisphere including Terzaghi already showed to be concerned with their role in granite foundations while in the southern regions Brazilian authors have found similar occurrences but also affecting individual lava flows of continental flood basalts in the foundations of major dams of the Parana Basin, which they designated under the particular name of “fault-joints”. This double-standard designation is self-explanatory of the difficulties involving their origin and related geomechanical properties: faults or just shear joints?Recently, similar features were encountered in the foundations of large dam constructions in anorogenic granites inserted in the realm of the Brazilian Amazon, where some of these discontinuities exhibit features common to tectonic thrusting combined with deep tropical weathering.The evidence of preshearing along the surfaces of such fractures, also associated to products of deep weathering, reduces their geomechanical strength substantially, suggesting values of ultimate phi spanning 12 to 28°. The detection of these descontinuities during initial investigation phases continues to be a major complex task in geological risk evaluations surveys. Trenching associated to some geophysical exploration techniques, although considered to be very basic exploration techniques are still the suggested methods for their forecast and previous determination."

Jan 1, 2015