Search Documents

Weekly Capacity ? Current Schedule Rate (198.5 tonnes / hour) X Skip Time (112.7 hours) X Effectiveness (85%) = Weekly Capacity (19,015 tonnes) Capacity Conclusions - Existing hoists optimized are best option for Fraser Morgan (>20M + schedule for other). - Peak will have to be managed. - Critical to have equipment & infrastructure in best possible condition to ensure reliability.

Feb 1, 2008

By D. B. Dreisinger, A. A. Gunaratnam

A pressure oxidation (POX)-hot cure (HC)-lime boil (LB) process is used in industry to recover silver from refractory gold sulfide ores containing minerals such as pyrite and arsenopyrite. Pressure oxidation is used to oxidize minerals and liberate occluded gold particles. As such, iron goes into solution and under acidic and high temperature conditions often precipitates as basic iron sulfate (BFS). BFS consumes excess lime during neutralization prior to cyanidation. Therefore, a hot cure stage is required to re-dissolve BFS back into solution. BFS re-dissolution consumes acid and produces ferric sulfate. In the presence of silver, these conditions favor the slow formation of silver jarosite. Silver jarosite is refractory to cyanidation, and must be broken down prior to cyanidation. This is done in the lime boil to produce a cyanide-soluble silver hydroxide. A study was conducted to investigate parameters that affect the precipitates that form in each stage of the POX-HC-LB process.

Jan 1, 2017

By C. L. Belyk

There are fifteen accepted types of uranium ore deposits and at least forty subtypes readily identified around the world. Each deposit type has a unique geological model which may also have unique processing implications. Primary uranium production in the past decade has come from a handful of these deposit types: unconformity, sandstone, calcrete, intrusive, breccia complex and volcanic. Processing implications for each of the fifteen deposit types can vary widely between and within different geological models. Some key characteristics of uranium deposits that may have processing implications include: ore grade, uranium and gangue mineralogy ? including clay and carbonate species and content, hardness, porosity, uranium mineral morphology, and carbon content. Processing roadblocks may occur as a result of one or more of these characteristics for any of the fifteen deposit types. Future technological advances and innovative thinking around uranium ore processing could provide avenues for roadblock removal setting the stage for additional and economically-viable uranium production from traditional and non-traditional uranium ore deposits.

Aug 1, 2010

By Randy McMeekin, Chris Twigge-Molecey, J. Peter Blake

The business objectives of a metallurgical project determine targets and constraints, such as the range of products, production capacities, in-service dates, and capital and operating cost parameters. Permitting is usually left to the project team, as are decisions regarding site location, technology, and construction approach. Success requires an orderly methodology, represented in this book by front end loading (FEL) phases: FEL1 examines several alternative approaches; FEL2 ranks and eliminates less economically or technically attractive options; and FEL3 develops the preferred option to the point of major permit completion, with defined scope, schedule, and cost to submit for approval to proceed with implementation in FEL4. Working through FEL1, FEL2, and FEL3, the project definition improves, estimates become more accurate, and project risks are reduced. The project design basis at the end of FEL3 is the control document for project implementation in FEL4.

Jan 1, 2015

By Maria D. Mastalerz, Wei Wang, Maria E. Holuszko, Amit Kumar

In this study, the micro-FTIR analysis was used to investigate in-situ surface properties of coal and its components (macerals) and these were directly correlated to the coal hydrophobicity as measured by the contact angle before and after reagent addition to understand the suitability of the reagent for flotation. The micro-FTIR technique can provide a semi-quantitative analysis of the chemical functional groups on coal surface, exactly where the contact angle is being measured. Selected functional groups and their ratios that provide information about aromaticity, the contribution of oxygenated groups, and aliphaticity are used to evaluate the reactivity between reagents and various coal components. The observations made in relation to the susceptibility of some reagents towards certain coal components should lead the way to a smarter way of using process design in terms of reagents selection for coal flotation.

Jan 1, 2017

By N. D. Wineinger, J. Jodouin

"An Independent Electricity System Operator Industrial Accelerator Program (IESO IAP) case study was completed for a mine in Ontario, Canada by SRK Consulting, Inc. The purpose of the study was to analyze the ventilation system to determine whether and which system improvements could reduce the overall electrical power demand of the mine. Financial incentives are offered by the IESO IAP grant program to help cover the capital costs of these improvements. This study included the completion of a full mine ventilation survey as well as measurement of a full suite of electrical parameters of the surface and underground ventilation fans. After these measurements, a base ventilation model was created and established as the system baseline. Changes to the ventilation system were modeled, and their effects on the power demand were projected. The results of the study showed that several improvements were possible which may significantly improve the efficiency of the ventilation system and reduce mine electricity demand.INTRODUCTIONIn 2017, a ventilation study was conducted in accordance with the Independent Electricity System Operator Industrial Accelerator Program (IESO IAP) at a mine in Ontario, Canada. The IESO IAP is designed to assist eligible transmission-connected Canadian companies operating in Ontario to fast track capital investment in major energy conservation projects. The program will provide financial incentives to encourage investment in innovative process changes and equipment retrofits to reduce electricity consumption on the provincial system and to help companies become more competitive by positively impacting their bottom line. There are now four initiatives under the Industrial Accelerator Program:1. Retrofit2. Process & Systems, including Small Capital Projects3. High Performance New Construction4. Energy Managers – a new initiative under the Industrial Accelerator ProgramWithin the program, companies may propose energy saving changes to their current systems where applicable and appropriate. Companies may then be awarded funding to implement the proposed changes. The program allows partial financial compensation to implement certain energy saving changes that would otherwise not be considered due to high capital costs. For larger projects, such as underground mine ventilation systems, a detailed engineering study must be submitted. This study must detail each energy saving change or measure, its savings, and calculate the financial incentives using the IESO IAP Payment Structure. The payment structure for a project is an amount equal to the lowest of the following (Independent Electricity System Operator, 2015):"

Jan 1, 2019

By J. K. Armstrong, C. Feyerabend

"As mines are constantly growing and expanding, so do the challenges for emergency response teams. They have to keep up with the pace set by current and future production techniques. Although mines have now reached depths of several kilometres and their dimensions and complexity are that of an entire city, mines rescue still must be able to reach the most remote areas within the mine in a swift and safe manner. The duration of breathing apparatus and physical human capabilities are limitations. Therefore, alternative methods have to be explored to extend the time under oxygen for mine rescue teams without putting additional stress on the team members. To address this global trend, Dräger, Goldcorp and PAUS have partnered to develop a mine rescue vehicle that allows mine rescue teams to travel for an extended period of time through a contaminated atmosphere without the use of breathing apparatus, thus extending the range of their mission. By applying currently available techniques, the safe expansion of mine production can be ensured, giving mine rescue teams the ability to respond to accidents in a safer and faster way. INTRODUCTION With the reduction of easily accessible natural resources, there is a global trend toward searching for higher ore grades underground and/or continually expanding mines underground to extend their lifetime. While in some areas this trend has just begun, in other countries mines are reaching depths or horizontal dimensions that pose extreme challenges (Codelco, 2016). These challenges include safety relevant topics, such as rock stability, heat and seismicity, but also more basic issues such as distances to the working face, which can become crucial considering the cost to develop a new shaft or decline. To overcome this, there is a growing interest in collaboration among various stakeholders to drive the development and support of deeper mines and tackle the complexity of underground mining. This is evidenced by the fact that several industry and research groups and networks have formed, e.g. the I2mine project in Europe and the Ultra-Deep Mining Network by the Centre for Excellence in Mining Innovation in Canada. Due to commodity pricing and the trend toward renewable energy, metal/non-metal mining will be the driving force behind this development."

Jan 1, 2019

By A. A. Shirzadi, E. R. Wallach

"Liquid gallium has been used successfully to modify/remove the surface oxides prior to diffusion bonding similar and dissimilar nickel-base superalloys. Using this approach, bonds in nickel-base superalloys with ""virtually invisible interfaces"" were produced, and the compositions in the bond region were very close to those of the bulk alloys. Room temperature tensile and bend tests showed no preferentially failure at the bond lines. Creep tests on samples made between two different Inconel alloys also showed failure away from the joint, i.e. in the parent metal of the Inconel alloy with lower creep resistance. The high temperature lifetimes of these samples were as long as those of the unbounded Inconel, confirming that the joining approach has no adverse effect on the nickel-base superalloys being joined."

Jan 1, 2006

By K. Negishi, H. Izui, Y. Komiya

"Aluminum has the disadvantage of low strength. In order to obtain the high strength composites, crystals were refined in the composites. Grain refinement was approached at two process points, generating new grains and grain growth. It is important for refinement how to control the grain growth. Spark plasma sintering (SPS) technique and TiB2powder addition prevent grain growth. To investigate effects of strain and additives to the alloy, aluminum powder was sintered at 70 MPa and 80 MPa, changing the content of TiB2additive powder by SPS method. As the results, the crystal grain size was finer in the composite sintered at higher sintering pressure and with larger amount of additive, though over 1.0mass% TiB2addition dissuades grain refining. These grain refinements improve hardness and tensile strength of sintered aluminum alloys.INTRODUCTIONAluminum matrix composites have low density, high specific strength, and low cost. Their applications are growing continuously in the field of automotive and aerospace industries. Recent studies to improve their good mechanical and tribological properties use different ceramic materials such as Al2O3(Das, Munroe, & Bandyopadhyay, 1996; Ashwatha & Anthony Xaviorb, 2014),SiC(Hassani, Bagherpour, & Qods, 2014), B4C(Ehsan, Masoud, Touradj, Amir Hossein, & Ali, 2015),TiC(Ehsan, Ali, Masoud, Kamyar, & Touradj, 2017), and TiB2(Fei & Zhong-Hua, 2013).On the other hand, grain refinement is also an important techniques for improving the properties of aluminum alloys. Finer grains improve the mechanical properties of the alloy. For cast and wrought alloys, addition of grain refiners in molten alloys accelerates generation of nucleus and suppresses grain growth. Al-Ti-B alloy is generally added as grain refiners in the molten aluminum alloys(Easton & Stjohn, 2001). Especially, TiB2has very high melting point, low density, and excellent hardness. Therefore, TiB2was selected as additions into aluminum alloys. Liquids reaction leads to high cost, oxidation, discoloration of molten alloy, and clustering of additive powder as compared with solid reaction such as sintering. However, sintering of aluminum alloy powder with ceramic powders is difficult for oxide layer surface. Recently, we take attention to spark plasma sintering (SPS) as advanced sintering process. SPS process can easily sinter a high quality specimen at a lower sintering temperature and in a shorter time than conventional sintering processes. By SPS process, we have sintered titanium powders that are as difficult to be sintered by any other processes as aluminum powders, and improved mechanical properties by adding hard ceramic powders TiC and TiB(Kamegawa, Izui, Komiya, Kobayashi, & Arimoto, 2015; Sampei, Izui, Komiya, Shigimura, & Suzuki, 2015). Furthermore, it is important to consider not only pure aluminum but alloys for solid-solution or precipitation strengthening. Actually, pure Al does not have enough strength compared with the alloys. Al-Cu alloy and Al-Mg alloy demonstrate adequate strength for industrial and commercial sectors. Al-Mg alloy retains good formability, and has high resistance to corrosion. It is therefore used for many applications. We must consider alloying processes. The most cost effective process is blended elemental technology where alloying elements are added to base powder as elemental or master alloy powder (Smugeresky & Dawson, 1981; Yasue, Radjai, Miwa, & Sakaguchi, 2003; Bolzoni, Esteban, Ruiz-Navas, & Gordo, 2012)."

Jan 1, 2018

By A. W. Jacob

THE shatter cut, or burn cut as it is often called, is one in which the centre of the round is almost reamed out by drilling holes so close together that the blasting of a few holes shatters the rock embraced by all of them. The idea of shattering the centre of a face by shooting holes drilled parallel to one another is not new. Some miners have used this method for years past, when drilling quartz or a face near timber. But, they followed the age-old practice of first blasting the cut, then the square-up. It was not thought possible to shoot both together. In the case of machine men, the two largest contributors to silicosis are dust from drilling and dust from blasting. It follows, then, that material reduction of exposure to either constitutes an important step in lessening the incidence o silicosis. It was? the hope of being able to do away with the necessity of the men having to return early to a face, through dust concentrations of 60,000 to 80,000 particles per cubic centimeter, that aroused interest "in the shatter cut at McIntyre. Efforts to this end were successful. Now, with this kind of cut, all holes of a round are shot simultaneously.

Jan 1, 1942

By J. W. Scott, G. G. R. Falkenberg

"The Syncrude project is an integrated complex designed to mine, extract and upgrade bitumen from the Athabasca tar sands to produce 129,000 barrels per day of synthetic crude oil. This paper provides a brief general description of the location, history and geology of the tar sands and the overall organization and structure of the project. The major emphasis and the bulk of the detail presented deals with the extraction plant; a material handling and mineral processing installation designed to treat 312,000 tons per day of tar sand feed.History of the Tar SandsThe Athabasca tar sand deposit was recorded in 1788 by Peter Pond, however the first serious geological mapping and exploration did not begin until 1915. Little interest was taken in the deposits until the Second World War, when the governments of Canada and Alberta conducted an extensive exploration program. In addition a number of pilot plants were sponsored during the 1940 -1950 decade. The hot water separation process was successfully demonstrated on the pilot plant scale during 1948 -49, and was established commercially in 1967 in the G.C.O.S. plant. The Syncrude plant, due to come on stream in April 1978, also employs the hot water separation process."

Jan 1, 1978

By Forrest A. Kerr

Northern British Columbia is a term which probably conveys to various individuals quite different meanings. To the average person it signifies an area of indefinite size and indefinite position which may start at Prince Rupert, Stewart, or somewhere else, and end at Alaska or .the Yukon. Many people, in their conception, fail to encompass in their mind's eye that vast tract of land lying ~o the east of the panhandle of Alaska. Few realize that the area north of an east-west line through Stewart represents more than one-third of the Province and is, of course, the part most appropriately designated as northern British Columbia. This section, more especially the northernmost 100,000 square miles, from political, geographic, and economic viewpoints stands isolated perhaps more than any other part of British Columbia. Unlike the rest of the Province, it has no coast line, being cut off from the Pacific ocean by a narrow strip of Alaska. It is bounded on the north by the Yukon, and on the east by Alberta. In the south this northernmost 100,000 square miles is limited by a divide of rugged mountainous country separating the drainage basins of the Stikine and Liard rivers from those to the south.

Jan 1, 1929

By O. G. Olvera, D. G. Dixon, E. Asselin, L. S. Quiroz

Dissolution rates of chalcopyrite (CuFeS2) were calculated using electrochemical impedance spectroscopy (EIS). The calculated dissolution rate decreased by a factor of 3.2 after the electrode was passivated. The results presented in this work indicate that the reduction of Fe3+ was the rate-controlling step for fresh CuFeS2 electrodes while the transport of cations within the passive film limited the dissolution rate for the passivated electrode. The transfer of cations at the electrode/electrolyte and passive film/electrolyte interfaces did not affect the dissolution rates of the fresh and passivated CuFeS2 electrodes, respectively. The catalytic effect of pyrite (FeS2) on the dissolution of CuFeS2 continued after the passivating treatment. The contact of fresh and passivated CuFeS2 electrodes with different FeS2 particles resulted in increased dissolution rates, due to an increase in the reduction rate of Fe3+.

Jan 1, 2014

By Yasuo Iizuka

We have had studied CO oxidation on unsupported Au powder (mean particle size, ca.100nm) manufactured by evaporating ultra high purity gold metal (>99.99%) in inert gas and reported that it showed some activity after oxidizing pretreatment in O2 at 423 K?453 K. However, recent XPS analysis of the Au powder revealed that it contains much amount of impurity metals such as Ag and In at levels which far exceed those expected from the impurity level of raw gold metal in the bulk. Several samples of Au powder containing different amount of impurity metals were prepared to examine whether the activity depends upon the existence of surface impurity or not. Activity measurements were performed at 273 K after undergoing the powder under various pretreatment conditions. Although the activity of Au powder varied to some extent according to the pretreatment condition, it is strongly correlated to the surface concentration of Ag. Such dependence was not found for In, indicating that the activity of unsupported Au powder is mainly due to the existence of Ag in the surface layer. The activity attributable to ?particle size effect? was not recognized for Au powder with a mean particle size larger than 80 nm.

Oct 1, 2003

By E. Gervais

"In today's marketplace, heavy competition between materials is the norm. This is particularly true f or the base metals, which are being increasingly challenged by new or improved materials in all traditional applications. Current usage of base metals results from a combination of a metal's intrinsic properties, and technology. The future of the base metal industry rests with innovative, high-quality product development, its ability to take advantage of the results of worldwide, massive material R&D investments, and with the dynamism and effectiveness of its market development programs.The ZA casting alloys program is an illustration of the zinc industry’s efforts to protect and expand its market position in the casting field through state-of -the-art technological developments. The market potential f or these advanced engineering alloys is substantial, and their impact on traditional zinc die casting alloy consumption is particuarly important. The ZA alloys, in offering increased performance through zinc castings produced at low cost and by a wide range of moulding processes, have unlocked a multitude of new end-use applications.Following a review of the development of ZA alloys, of their key properties and of their performance characteristics, the numerous challenges that the alloys present to the zinc industry and to the R&D community are discussed.IntroductionZinc is anodic to steel and has a low, uniform rat e of corrosion; it has a low melting point, can be cast with precision , and is readily finished. In addition to its use in protecting steel and in the production of a wide range of castings, zinc is employed : (1) to produce brass, high-strength aluminum alloys and magnesium die casting alloys, (2) in the wrought state for coinage and in building products, particularly as roofing materials , and (3) as an oxide, in the rubber industry, in ceramics, glass, cosmetics, pharmaceutical products and as the starting materials for many chemicals.Zinc die castings are produced with accuracy at high speed, at low cost, are easily finished and have excel1ent mechnical properties . Car fuel economy, changes in automobile styling, competition from other materials, increased sophistication of design and miniaturization have all led to a dramatic change in the volume of zinc consumed for die-casting applications. This has been particularly notable in the United States. Throughout the 19505 and the I960s, casting was the fastest growing major use of zinc; it was firmly established, accounting for 35% of the total zinc consumption(1), By 1983, the volume of zinc being purchased for casting applications had dropped to less than 20% of all zinc consumed in the United States. In the western world(2), consumption for zinc casting application s is currently at about 15%; being nearly equal to the zinc consumed by the brass industry. Coating applications dominate with a consumption of more than 40% of the total market."

Jan 1, 1987

By J. G. Kelly

"IntroductionOver the past twenty-five years of improvements to scooptrams In the Ontario Division of Inco Ltd., records indicate that on average, an 8 yard capacity machine at 80% availability will load, haul and dump about 100TPH from an average stoping area. This, essentially, means that Inco mines are limited to 2000 TPD as an approximate maximum production cap per minute. Some of the improvements made to scooptrams over this period have been:• dry disc and oil immersed brakes on larger loaders;• to replace air over hydraulic systems;• modulated shift transmissions;• greater breakout and tramming capacities by using larger engines and buckets;• operators' compartments have been enlarged and better seats,• joystick controls and air-conditioned cabs have been utilized'• major cost savings have been realized through tire maintenance improvements; and• major savings, safety improvements and increased ore recovery by using remote controls.After reciting the improvements listed above, and the list is by no means exhaustive, it is quite obvious that scooptrams are a mature product and that major design or performance improvements will not occur in the futre. Any futher improvements will be incremental in nature. Loading, hauling, and dumping with scooptrams is a batch process and as such is limited in its total output.Continuous Load/Crush/Convey Systems:In order to improve productivity, a radical new system was required. The target was 2000 tons per shift. In 1984, to meet the goal, Inco acquired the rights to a contiunous loader from Canadian Mine Services. Inco made modifications to the original prototype machine, such as: (I) conversion from rail mounted to crawlers for increased mobility; (2) a hydraulic cooling system was added; (3) flight bars were changed from cast to forged; (4) motor horsepower increased to 200 hp from 150 hp. Emerging from these modifications came a machine known as the CL-looo Oscilloader (Fig. 1).The CL-looo Oscilloader is an electric hydraulic 35-ton machine which is crawler mounted and has a drawbar pull of 30 tons. It has an adjustable frequency, oscillating lip which simulates the digging action of a manual .shovel. This action agitates and lifts the muckpile enough to allow it to settle by gravity onto the chain and flight conveyor table which then removes the ore to the tail end for discharge into either a crusher, a conveyor, a truck, or a combination of these.Late in 1985, six oscilloaders were fabricated and put into Inco mines for field trials. At Creighton Mine some early field trials were conducted with a rail mounted continuous loader loading directly into 140 cu.ft. Granby cars. Much of the field testing was in VRM drawpoints with the Oscilloader loading into 20-ton trucks or into Teletrams . At Levack Mine, by puttmg the truck on remote control, it was possible to have the operator run the Oscilloader and load his own truck (Fig. 2). At McCreedy West Mine, Copper Cliff North Mine, and Copper Cliff South Mine, the Oscilloaders discharged directly into 26-ton trucks."

Jan 1, 1988

"This document establishes standards and guidelines for scientific and technical disclosure by Issuers listed on the TSX Venture Exchange on their mineral properties. It incorporates and expands upon the minimum standards prescribed by Securities Laws and applies to all oral statements and written disclosure made by an Issuer or on behalf of an Issuer involving mineral properties.1. Introduction1.1 General(a) This Appendix establishes standards and guidelines for scientific and technical disclosure by Issuers on mineral properties. These standards and guidelines should be applied prudently and with common sense by those Issuers in conjmction with the applicable requirements of section 1.2.(b) This Appendix incorporates and expands upon the minimum standards prescribed by Securities Laws and applies to all oral statements and -written disclosure made by an Issuer or on behalf of an Issuer involving mineral properties.(c) This Appendix is not intended to be exhaustive or all-encompassing and greater detail may be appropriate and required in certain situations. Issuers are encouraged to contact Exchange technical staff where they are not certain about the requirement for disclosure on mineral properties."

Jan 1, 2003

"These guidelines set out information on timely disclosure of news releases which are intended to provide, existing shareholders and potential investors, factual information on which a reasoned investment decision can be made.Consider the problems and concerns raised by the following hypothetical news releases:Natural Resource Company""The Company has recently optioned a large and exciting gold property near the ""XXX"" gold discovery area. In describing the property, the Company's independent consultant has said: ""The favourable location of, and some of the results of prior work done on the property give the Company a worthwhile mineral exploration opportunity .... "". The Company proposes to expeditiously conduct a sizeable exploration program on the property as soon as the appropriate financing has been arranged.""Non-Resource Company""Based on discussions with several European countries, the Company anticipates that it will have orders to ship over 200,000 crates of widgets to those European countries over the next two years. These orders, which considerably exceed the Company's forecasts for the first year, represent a projected profit to the Company in excess of $1,000,000 over the next five year period.""GuidelinesTimely disclosure news releases are intended to provide, to both existing shareholders and potential investors, factual information on which a reasoned investment decision can be made. National Instrument 43-101 Standards of Disclosure for Mineral Projects provides requirements for disclosure of a scientific or technical nature for a mineral resource company.The examples do not provide sufficient detail and are misleading because material information is omitted. The following guidelines should be observed when preparing a news release:"

Jan 1, 2003

By M. D. Johnson, R. K. Bezys

"The majority of Ontario's limestone and dolostone production comes from a few Paleozoic carbonate units. In eastern and central Ontario, Ordovician rock units, which are the main sources for production, include the Oxford, Gull River, Bobcaygeon, Verulam, and Lindsay Formations. They are predominantly utilized for aggregate and cement manufacturing, with the Bobcaygeon Formation being used as a source of building stone. Along the Niagara Escarpment, the Silurian Lockport, Amabel, and Guelph Formations are sources for the limestone industry. The largest tonnage of rock extracted by the industry comes from these Silurian units, especially the Lockport and Amabel Formations. These units are used primarily for aggregate, although they are also a source for lime. In southwestern Ontario, the Silurian Bertie Formation and Devonian strata, represented by the Bois Blanc Formation, Onondaga Formation, Detroit River Group, and Dundee Formation, contribute to Ontario's production of lime, cement production and crushed stone. The Detroit River Group (Lucas and Amherstburg Formations) is the main source of the lime and cement produced in the province.Northern areas, which may become significant sources for the industry, include Manitoulin Island, the Lake Timiskaming area, and the James Bay Lowland. IntroductionThe Engineering and Terrain Geology Section of the Ontario Geological Survey has undertaken a geological inventory of all active and abandoned limestone and dolostone quarries in Ontario. This geological study, combined with a commercial study of active quarries carried out by the consulting firm of Derry, Michener, Booth and Wahl, will provide an up-to-date report on the industry in the province and will be published by the Aggregate Resources Section of the Ministry of Natural Resources. This report will follow the format and style of D.F. Hewitt's Ontario Department of Mines Industrial Mineral Reports and Circulars (Hewitt, 1960, I964a, 1964b, 1964c; Hewitt and Vos, 1972). Examinations of the quarries were carried out by geologists in the Paleozoic I Mesozoic Geology Subsection of the Engineering and Terrain Geology Section, and include, in addition to the authors, R,R. Wolf, V.A . Mazur, and D.K. Armstrong in the summer of 1986."

Jan 1, 1988

By M. D. Johnson, R. K. Bezys

"The majority of Ontario's limestone and dolostone production comes from a few Paleozoic carbonate units. In eastern and central Ontario, Ordovician rock units, which are the main sources for production, include the Oxford, Gull River, Bobcaygeon, Verulam, and Lindsay Formations. They are predominantly utilized for aggregate and cement manufacturing, with the Bobcaygeon Formation being used as a source of building stone. Along the Niagara Escarpment, the Silurian Lockport, A mabel, and Guelph Formations are sources for the limestone industry. The largest tonnage of rock extracted by the industry comes f rom these Silurian units, especially the Lockport and Amabel Formations. These units are used primarily for aggregate, although they are also a source for lime. In southwestern Ontario, the Silurian Bertie Formation and Devonian strata, represented by the Bois Blanc Formation, Onondaga Formation, Detroit River Group, and Dundee Formation, contribute to Ontario's production of lime, cement production and crushed stone. The Detroit River Group (Lucas and Amherstburg Formations) is the main source of the lime and cement produced in the province.Northern areas, which may become significant sources for the industry, include Manitoulin Island, the Lake Timiskaming area, and the James Bay Lowland. IntroductionThe Engineering and Terrain Geology Section of the Ontario Geological Survey has undertaken a geological inventory of all active and abandoned limestone and dolostone quarries in Ontario. This geological study, combined with a commercial study of active quarries carried out by the consulting firm of Derry, Michener, Booth and Wahl, will provide an up-to-date report on the industry in the province and will be published by the Aggregate Resources Section of the Ministry of Natural Resources. This report will follow the format and style of D.F. Hewitt's Ontario Department of Mines Industrial Mineral Reports and Circulars (Hewitt, 1960, I964a, 1964b, 1964c; Hewitt and Vos, 1972). Examinations of the quarries were carried out by geologists in the Paleozoic I Mesozoic Geology Subsection of the Engineering and Terrain Geology Section, and include, in addition to the authors, R,R. Wolf, V.A . Mazur, and D.K. Armstrong in the summer of 1986."

Jan 1, 1988