Search Documents

?NWCC has the highest number of Aboriginal students of any post secondary institution in BC and the region served includes 25 bands ? Chair of the Board of Governors is Irene Seguin (Hagwiloo K?am Saxwhl Giis) from Gitwinksihlkw ? FN council ? 39 First Nations Members * focus is to develop policy recommendations to increase student success rates

May 1, 2009

Up to thirty years ago, coal preparation in western Canada, except at four plants, had not included actual coal washing. The exceptions were at Nanaimo and Royston, B.C., where tub washers and wet tables were in use; at Hosmer, B.C., using. Robinson cones; and at Leitch Collieries, Passburg, Alta., using a feldspar jig. The two last named collieries had a short life and were not operating in 1920. The industry was divided, as at the present day, into two sections, steam (bituminous) coal and domestic (largely sub-bituminous) coal, the first generally supplying industrial needs and the second householcl and other heating requirements. The two sections overlap to some small degree today as prepared sizes, chiefly stoker, and briquettes, from steam coal are shipped for house-hold use, and domestic slacks are used in certain industrial plants. The .domestic operator, for reasons shown later, was not primarily concerned with actual coal washing as a phase of coal preparation, and bent his efforts to improvement of screening and loading plants, with hand-picking of coarse sizes. The bituminous operator, on the other hand, felt it necessary by 1920 to consider coal washing. When the mines were comparatively young, coal quality could be controlled to a considerable degree by selective mining, by leaving behind some of the seam or by-passing districts in a mine where the coal was of inferior quality to that in other districts. This obviously had its limitations, and so the next step was coal washing.

Jan 1, 1952

By Robert D. Brown

"All ten Canadian provinces have now tabled their 1981 /82 budgets . Only the provinces of Ontario, Quebec and British Columbia made more than minor modifications to their tax structures, with both Ontario and Quebec imposing major tax increases. In the past year, the federal budget was also released in the spring. Not so this year: we have that to look forward to in the fall!This month, Tax Notes presents a brief summary of the more significant tax changes introduced at the provinciallevels in the last months.Summary of provincial tax rate changesThe tax changes in this year's provincial budgets were both up and down- but there were far more tax increases than tax cuts.At the corporate tax level, two provinces, New Brunswick and British Columbia, increased their general corporate income tax rate; the former by two percentage points and the latter by one percentage point. Quebec, rather unexpectedly, sharply cut its corporate tax rate on business income, but increased some of its other business taxes at the same time. British Columbia reduced its corporate tax rate on small business income by two percentage points and Saskatchewan by one percentage point."

Jan 1, 1981

By J. Peck, M. J. Scobie, M. D. Pollitt

"IntroductionOne aspect of current research in the Canadian Centre for Automation and Robotics in Mining (CCARM) involves the automatic identification of different rock types based on particular drill performance parameter responses. In this paper, the four drill performance parameters of torque, pulldown pressure, rotary speed and penetration rate, were measured from an instrumented rotary blasthole drill during field investigations undertaken at the Fording River Mine, Elkford, British Columbia. The variations in these parameters were subsequently correlated with the corresponding rock types using the results from gamma, neutron and core logs in the same or adjacent boreholes. Work to date has sought to understand the relationships between drilling performance parameter variation and rock properties. Using the results of these studies, the present research is aimed at developing techniques whereby classical statistical pattern recognition methods are applied to drill data to permit the discrimination of different rock units. A monitoring system incorporating such a capability would greatly enhance the quality and amount of geological information on a per borehole basis while drilling. This data in tum could be used economically and directly towards explosive loading, geological exploration and reserve estimation. Background and PhilosophyThis work is an extension of equipment monitoring studies at the Fording River Mine. At this site over a two-year period, 5180 m of data was acquired on an instrumented Bucyrus-Erie 60R drill during routine production blasthole drilling. Throughout these studies, a 311mm diameter S8M Security tungsten-carbide tricone bit was used. The mine, located in southeast British Columbia, is a large-scale, open pit coal operation. The means of excavation revolves around a drill-blast-muck cycle and employs a standard shovel-truck system of transport. Four main rock types are present: sandstone, siltstone, mudstone and coal, with average compressive strengths ranging from 10 MPa to 150MPa respectively (peck 1989). However, based on the field studies, very few differences in terms of strength and compositional properties were seen between the sandstones and siltstones at the site. Therefore, they are referred to as sandstone/siltstone in all further discussions."

Jan 1, 1991

By Dalton. J. L., H. P. Dibbs

An account is given of investigations into the application of two neutron methods to the on-line analysis of slurries. One deals with the application of the neutron moisture gauge principle to the determination of the water content of iron oxide slurries, and the other with the application of gamma radiation from thermal-neutron-capture to the determination of the composition of aqueous slurries of iron oxide, copper oxide, zinc oxide and sulphur. Linear relationships were found between the composition of the slurry and the neutron count-rate in the first study, and between the slurry composition and the prompt-gamma-ray count-rate in the second study. A mathematical relationship has also been developed which relates changes in the prompt-gamma-ray counts from hydrogen to changes in slurry composition.

Jan 1, 1973

By J. W. Smith, J. G. Eacott, D. H. Napier

"Three hydrometallurgicat processes (Noranda chloride leach, B. C. Research biological leach and Sherritt-Cominco activated oxygen leach) and the Noranda pyrometallurgical process have served as the basis for design projects in the final year of the chemical engineering program at the University of Toronto. Each member of a team of five or six students devotes about 200 hours to the project and the final report is expected to include an economic analysis.None of the processes has been developed to full- scale plant, nor, in the case of the B.C. Research and Noranda processes, were pilot plant data available. Nevertheless, the designs developed provide a useful basis for a preliminary estimate of capital and operating costs and for a preliminary assessment of project feasibility.This paper discusses the approach used in the design projects with respect to engineering and economic aspects, and outlines the educational features and benefits of such a program as well as some of the problem areas that arise.IntroductionAs part of the undergraduate degree course in chemical engineering at the University of Toronto, students devote some 200 hours to a design project in their final year. Hydrometallurgical processes, not yet proven at the commercial scale, have been selected for study. The students are required to develop laboratory and / or pilot scale results into a conceptual plant design, using sound engineering principles. Capital and operating costs are then determined and a preliminary feasibility study and economic analysis are carried out."

Jan 1, 1986

By M. I. Kalashnikova, Y. M. Shneerson, E. E. Zhmarin, Y. V. Degtiarev, E. M. Vigdorchik

Separation of a magnetic fraction from nickel concentrate following matte flotation, and its treatment in a separate circuit enable reduces precious metals losses. The magnetic fraction is treated in two stages of oxidative leaching: atmospheric and pressure leaching. A study of the atmospheric stage, using mathematical modelling, is described in this paper. The mathematical model and experimental data were used to carry out industrial process calculations. The model enabled extrapolation of the results of batch laboratory test to industrial-scale continuous processing and the selection of optimal process conditions and large-scale equipment. In December 2004, commercial oxidative leaching tests were performed on the magnetic fraction at the Severonickel Plant (Monchegorsk, Russia). A comparative analysis of the mathematical modelling results and the actual process parameters is presented.

Jan 1, 2005

By Rae Simpson

"This paper provides insight into the elements of computerized maintenance systems and identifies some of the factors which influence their effectiveness. The paper describes what to expect in terms of benefits and problems, the nature of effective computerized maintenance systems, some of the systems available and a process for selecting a system for your organization.The paper will be of interest to mining company executives and maintenance or computer personnel who are involved with, or contemplating, the introduction of computerized maintenance systems.IntroductionIn the drive to improve profits in an increasingly competitive world, mining companies are now using some of the most sophisticated equipment available. The introduction of large and complex equipment such as drag lines, haul trucks, and high-capacity milling equipment has resulted in order-of magnitude improvements in productivity. However, this productivity is now, more than ever, dependent on the continued operation of the equipment. A prolonged breakdown of a critical component can have a significant effect on companies' bottom-line results. As more technologically sophisticated equipment is introduced, maintenance costs become an increasingly important factor for mining companies.Fortunately, sound modern management principles are being used more often in maintenance departments. Progressive maintenance managers are turning to computers to help manage the myriad of details associated with running a maintenance organization.Some maintenance departments in larger mining operations would find it difficult, if not impossible, to operate at current productivity levels without their computer systems. Unfortunately, some other companies gain very little from their computerized systems and would probably be better off without them.How can you be sure that computerized maintenance will improve the maintenance picture for your company? What benefits can you expect to achieve? How do you go about selecting a maintenance system for your organization? These are some of the questions facing industry managers and executives today. In the following sections, we will provide some guidelines and insights to help address these challenges."

Jan 1, 1988

By Richard Dawson

Presentation Outline? Northeast BC Coal Fields Overview and History ?New mines and projects in development ?Design Issues for steeply dipping footwall slopes ?Design issues for angle-of-repose waste rock dumps

May 1, 2006

By J. W. Hohn

The precipitation of Fe(III) to form ferrihydrite in the presence of arsenic is the United States EPA's Best Demonstrated Available Technology for treating arsenic-containing hydrometallurgical solutions and waste streams. This technology has been widely adopted throughout the world and developments have been well reviewed. The adsorption and long-term stability of ferrihydrite can be improved by co-precipitating Fe(III) and Al(III) together to form an aluminum-modified ferrihydrite. Arsenate adsorption into ferrihydrite and modified ferrihydrite as a function of pH, Fe/As or (Al+Fe)/As mole ratio, and the initial As(V) concentration is presented and compared. The results of long-term aging of both adsorbents at 70°C for over a year are also summarized.

Jan 1, 2006

By Bennett McLaughlin, Gille Brousseau, John F. Cook

"La Mine Bousquet commenced operations in October 1979. Mining has been by underground methods from two main zones which dip steeply to the south , Sub-level stoping methods with following fill are used.The orebody and immediate country rocks are sericitic and highly schistose. The intensity of schistosity varies significantly and poor ground conditions prevail, especially within the orebody,Initially few mining problems were encountered but in May 1981, significant damage occurred. A system of stabilizing pillars was introduced with improved support systems. Predevelopment in ore and pre-drilling of blastholes were reduced with extra footwall development.Damage has continued to occur on a regular basis particularly during the spring thaw. Generally, the adverse conditions have been successfully overcome.IntroductionMost of the mining problems that have been experienced at Bousquet have been caused by poor ground conditions . This pa per describes these conditions, considers the cause and describes the ways in which the conditions have been dealt with . Despite the problems, Bousquet is a successful operation which in 1983 produced 95,000 ozs of gold from 514,000 tons of ore."

Jan 1, 1985

By George W. Bain

Summary During the last three years the discovery of gold in the belt of volcanic and sedimentary rocks extending eastward from the Porcupine and Kirkland Lake gold-fields has caused a great deal of excitement in mining circles. The area is heavily drift covered, and every aid to the location of veins is eagerly grasped. A knowledge of the physiographic history of the area is of the utmost importance in the application of many of these aids. Evidence is presented to show that glacial erosion has lowered the general elevation very little below the pre-glacial level, and that many glacial erratics have been carried less than three miles southward. Probably a knowledge of the general geology of a: region was never more necessary to the understanding of the distribution and continuation in depth of the mineral veins than in this area. Four distinct granites occur in the region, and gold-bearing veins are genetically associated with only one of these. Two types of quartz-feldspar porphyries have been found, only one of which has any bearing on the locus of the mineral veins. Many other examples of this complexity of associations might be cited, but everyone goes to show that in most cases the economic importance of the deposits can be realized only after the regional geology is understood. A series of sandstone, limestone and shale intruded by granite lies unconformably below the Keewatin lavas. The latter are intruded by a gneissoid granite and are overlain unconformably by the thick series of Timiskaming greywackes and silts. These are intruded by carbonated syenites and syenite porphyries which have since been rendered somewhat schistose.

Jan 1, 1927

By Derek J. Barratt

This paper compares a number of operating conventional and semi-autogenous grinding circuits and analyzes them in regard to operating and capital costs, specifically as applied to porphyry copper ores.

Jan 1, 1979

By A. I. A. Salama, M. W. Mikhail, R. J. Mikula

"The Coal Research Laboratory (CRL) of CANMET along with other research organizations in coal-producing countries envisage major benefits from computer applications in coal preparation, Some of these benefits are greater system flexibility, improved coal preparation plant performance efficiency and efficient utilization of manpower, all of which result in economic benefits. Computers can be applied for both on-line and off-line purposes; this paper focuses on the on-line applications from the process control point of view.A critical discussion of the different analog and digital process control systems is presented. Recent developments in Great Britain, West Germany, Poland and Australia on automation and instrumentation using on-line measurements of coal ash and moisture contents are identified.The CRL research and development strategy aimed at achieving on-line computer control of an automated coal preparation plant is presented.IntroductionIn the past twenty years an enormous progress in the area of computer technology has been noticed. Computer applications in industrial processes offer greater system flexibility, improved plant performance efficiency and efficient utilization of manpower. Significant computer control development in mineral processing has already been achieved. Although progress has been made in the area of computer applications in coal preparation, more effort is needed to utilize the full potential.The computer applications in coal preparation can be viewed as off-line and on-line. Considerable progress has been reported in the area of off-line computer applications, especially in the areas of modelling, performance evaluation/prediction and statistical analysis. However, only modest progress in on-line applications has been reported(1-7). This paper will focus on: online instrumentation and process control applications, different analog and/or digital control systems, on-line automation and instrumentation in other countries and CRL strategy toward pilot plant automation."

Jan 1, 1985

By Navid Bahrani

Overview ? Case history of footwall slab failure ? Procedure used to build a finite element model ?? Pre- and post- mining topography ?? Slab geometry ?? Excavation stages ?? Input parameters ? Finite element modelling results ?? Unloading-induced displacements (magnitudes & directions) ?? Calibration of overall model using measured prism displacements ?? Shear stresses and displacements along the base of slab ?? Factors of safety at different stages ?? Effectiveness of rock bolts ?? Staged or unstaged model? ? Conclusion

May 1, 2008

By John H. Fowler

"Barytes is one of the major components of drilling fluids used in oil and gas well-drilling. This mineral's close association with the petroleum industry bestows it with a commodity status not enjoyed by many other industrial minerals. Approximately 85% of world barytes production is used as a weighting agent in oil and gas well drilling while the remaining 15% is consumed mainly in the manufacture of barium chemicals, glass and as a pigment, filler or extender.Barytes mining began in Nova Scotia around 1865 and has continued until the present. Currently there are three barytes producers in the province one exporting pharmaceutical-grade barium sulphate and the other two supplying drilling mud-grade barytes to the offshore. Several barytes exploration and development programs are underway with excellent possibilities that Nova Scotia deposits will supply a significantly larger share of the drilling mud-grade barytes used in east coast drilling programs.Currently there is renewed interest in barytes activities in Nova Scotia because of its use as a weighting agent in drilling flu ids used in offshore oil and gas drilling programs.This paper reviews the use of barytes by the well drilling industry; outlines the history of barytes mining in the province, progressing to present-day exploration, development and production activities underway in Nova Scotia; and concludes with the market potential for Nova Scotia barytes."

Jan 1, 1986

By Gerald Sanders

Presentation Topics ? We?re Going to the Moon Again? ? What is Lunar Mining ? In-Situ Resource Utilization? ? What Are The Challenges to Lunar Mining? ? What is NASA Currently Doing?

May 1, 2009

By D. Lessard, S. Nantel

"Surface crown pillars are important Canadian,mining structures. Mines operating in the Canadian Shield usually have several, forming a first line of protection from surface elements.Detailed technical information from twenty-four Canadian hard rock mines show that the deposits dip steeply and are generally either single or multiple veins. Considerable overburden usually cap the deposits. The rock mass is often altered and intersected by important discontinuities.The designs for these types of pillars lack basic data and are based on experience rather than a scientific approach. Regardless of the competence of the rock mass, the surface crown-pillar thickness to width ratios (an unscientific design tool used by the industry) are usually less than five. Rock bolting is, in almost every case, used as a support measure. However, there are many openings neither backfilled nor monitored.The characteristics of openings with surface crown pillars are also examined."

Jan 1, 1988

By P. K. Chatterjee

"The operations of a large-scale open-cut mine are simulated to produce a user-oriented interactive digital model. SIMULA is chosen as the programming language and a sophisticated data base system is designed to consider the complex information network of large mines. The main features of the program are the mine planning and mine evaluation modules. These modules are responsible for the computation of truck-shovel performance and other equipment details in a mine. Stochastic methods are employed to generate event times. The use of a Data Base Management System and the data base provide an efficient method of information storage and retrieval. Truck allocation techniques have been examined in detail and comparisons between random dispatching and conventional methods are made. The model is intended for mine operators and engineers and the program is well structured and very readable. It is hoped that these features will make the model readily acceptable.IntroductionThe Department of Mining and Metallurgical Engineering at the University of Queensland has been conducting research into computer simulation methods in mining since 1972. The research has been mainly applied to actual operations, with both open-cut and underground mining being equally emphasized. The results of the research to date have not only strengthened the methodology of the approach to complex mining problems, but have also increased confidence in the use of modelling and computer simulation technique s in mining.The model described in this paper translates a complex LHD situation into a user-oriented interactive digital model using SIMULA. The present methods of evaluating truck dispatching and trolley assist are tedious and laborious. This model provide s the engineer with readily acceptable means of rapidly assessing the relative merits of these techniques in a large-scale open-pit operation. Poor utilization figures in many current operations (for example, 40% for trucks, 70% for shovels) are of serious concern to mine officials and computer-controlled dynamic truck dispatching systems have been considered by some of these mines to improve equipment utilization ."

Jan 1, 1981

By J. Kochhar, Robert G. Cooper

"The Cape Breton Development Corporation is a federal Crown corporation which was formed in 1968. Initially, the Corporation had two divisions - the Industrial Development Division, whose purpose was to stimulate Cape Breton Island's economy, and the Coal Division with a mandate to phase out the operating coal mines. However, that strategy changed in the early 1970s with the Middle East oil crisis. As a result of that crisis, Nova Scotia Power Corporation adopted an ""off oil"" policy. Today, approximately 700/0 of Nova Scotia power needs are met by generation of electricity from coal. Therefore, since the early 1970s, emphasis has been on the rehabilitation of the Cape Breton coal mining business with the opening of three new mines.Today, Devco is solely a coal mining company which employs 3300 people.Physical DescriptionThe mines operate in the Sydney coal field which is located on the eastern tip of Cape Breton. The Corporation leases the deposit from the province of Nova Scotia and its leases cover all coal from the outcrop to the 4000 ft depth. The seams outcrop along the shoreline and dip beneath the ocean floor at dips varying between 5% and 100%.There are eleven seams, of which three - the Harbour, Phalen, and Hub - have been extensively mined."

Jan 1, 1990