Search Documents

By C. W. Sheng

In this paper conventional construction procedure is briefly described for the installation of stone columns in soft ground in China. A viewpoint concerning the mechanism of ground improvement by use of stone columns is presented for discussion. Based on the information obtained from field measurement and observation three important problems relating to the construction and design of stone columns are discussed. Finally, a case history is given to show that short stone columns floating within the weak soil layers may in some instance be used to improve the weak strata of great thickness.

Jan 1, 2010

By Timothy C. Siegel

Drilled displacement piles (also known as augered cast-in-place displacement piles or augured, pressure grouted displacement piles) are installed by the displacement of soil and subsequent placement of fluid cement grout within the evacuated volume. Depending on the soil grain-size characteristics, soil behavior, in situ soil density, pile spacing, and pile diameter, the installation process can result in measurable densification and an increase in lateral stress. This paper examines the conditions prior to and following the installation of drilled displacement piles at sandy sites using the cone penetration test. The data support that the installation of drilled displacement piles results in a substantial increase in tip resistance.

Jan 1, 2007

By Kyle M. Rollins

To improve our understanding of lateral resistance of pile groups, a series of lateral load tests were performed on a full-scale pile group using both static and dynamic loads. The pile group consisted of nine 0.6 m-diameter steel pipe piles driven into clay. During the static tests, the load was cycled fifteen times to evaluate the drop in lateral resistance that would occur due to repeated loading and the formation of a gap. The peak load typically decreased by about 15% from the initial cycle to the last cycle. The load carried by each pile was also measured and there was a significant drop in resistance for the piles in the trailing row relative to the leading row. The dynamic force was applied using the Statnamic loading system which produced a lateral force of 3500 kN (787 kips) in about 0.1 seconds. In two cases, dynamic loads were applied following application of 15 static load cycles. In these cases, the dynamic lateral resistance was about the same as the static resistance, likely due to gaps around the pile. In three other cases, the dynamic force was applied prior to the cyclic loading. In these cases, the dynamic resistance was 30 to 60% higher than the static resistance. Simplified analyses suggest that the difference in resistance could be attributed to damping produced by the soil surrounding the piles during the virgin loading.

Jan 1, 2002

By Christian Hoyme, Jochen Maurer

Most of the current foundation projects are suffering from disconnected information silos. In the first silo there is the planning of the project with corresponding data, presented by paper or digital drawings. Here will Building Information Modeling (BIM) be one of the trends for the future. We will see more and more projects leaving the “old way” of 2D drawings and moving into 3D planning including metadata of the foundations. But even with a perfect BIM model of a jobsite, we are not at final end of digitalization. While execution of the project at the jobsite, a second data silo is evolving. Data collected directly from construction equipment and manual measurements is currently undervalued in most projects. Paper is passed to the equipment operator and major data from measurements on site are noted on paper and digitized afterwards. Automatically collected data is not be used to create site progress reports or similar report. So, the real “data” just flows around without connection to any other data already existing in projects. And then the third silo arises: The documentation of the project. Data collected on paper es reentered to create some basic documentation of the work handed over to the client. Spreadsheet software is still the “tool-to-be-used” to create at least some documentation. Finally, the documentation is not connected to the data created while planning and not connected to the automatically collected data from the jobsite. A connected jobsite in the foundation industry must link these information silos and have to create a full data-workflow from the design through the execution to the as-built documentation. INTRODUCTION Building information modelling (BIM) is currently the most popular term of construction business in Germany and probably all over the world. But as often there are many different definitions out there and everyone has his own definition or at least understanding what BIM is about. But for sure it is the most relevant for the construction industry in the near future. Most popular is the digital twin for the upper structure of a building. In most cases the BIM models just shows the building itself, but there is more to be implemented. For example: projects where a special foundation is needed, BIM should include also the foundation elements with meta data. There are several advantages. Not only the clash detection of anchors, but also the possibilities to check the interaction with neighbor constructions, power lines and so on are a use case. For sure most of the special foundation elements are not relevant for the whole lifecycle of a building. But during construction and later the demolition the information about the hidden elements is important and gives a benefit to all stakeholders. In the future there will be not the question: “What is already in the ground?”. The risk for following construction projects on the same ground will be minimized.

Jan 1, 2019

By K. Rama Sarma

Piles are frequently subjected to lateral forces and moments in addition to vertical forces and hence the piles have to be designed for both lateral loads as well as vertical loads. In the design of such pile foundations, two criterias must be satisfied. First an adequate factor of safety against ultimate failure and second, as acceptable deflection at working loads. In this study the work has been carriedout to study the lateral deflection pattern of the pile. The solutions to the problem primarily depend on soil modulus. Equations for computing the values of slope, deflection and coefficients for many types of soil conditions have been developed for static loading for long piles. As analysis part is not available for the above methods for the values of depth coefficients in the tables. It is required to go for linear interpolation which is not valid and highly unreliable. In this present method, coefficients can be obtained for any value of depth coefficient (z) with simple calculation. The present method is very concise and allows one to ana­lyse any type of pile with varying depth coefficient (z) even without the availability of any practical data regarding applied lateral load (P1) and moment (M1).

Jan 1, 1996

By David Pierce

The Port of Seattle, one of the largest on the west coast of North America, made a strong statement regarding their support for reusing existing structures when a decision was made to rehabilitate Pier 69, on Seattle's downtown waterfront, for their new headquarters. Because of its age and location, the pier provided an unusual challenge to the Port and its consultants. The Port hired Peratrovich, Nottingham, and Drage Inc. to design the seismic strengthening of the pier itself. To remedy the lack of seismic resistance in the 70-year-old pier, PN&D designed a new steel-pipe-pile supported concrete apron next to it. The structure relied on a development by PN&D, the "spin-fin pile", to achieve the tension capacities required of the batter piles. The construction of this apron was completed in October of 1991. Another team of consultants performed the superstructure renovation design, which is now under construction.

Jan 1, 1992

By Cem Akgüner

The displacements of axially loaded single piles are analyzed with an approach based on elasticity. Young?s modulus and Poisson?s ratio of the soil encompassing a pile are the unknowns required as input to obtain predictions based on the elastic method. Attention is directed towards Young?s modulus because the range and variability of Poisson?s ratio is not significant in displacement calculations. A database of axial pile load tests established for the California Department of Transportation (Caltrans) is investigated. All of the tested piles were driven into the ground. Measurements of displacements and loads were made only at the top of the pile. First the magnitude of displacements is determined up to loads that are half of the failure load measured from pile load tests. Various correlations for Young?s modulus are then employed to determine how accurately each predicts the actual measured displacement. The chosen correlations utilize the routinely available parameters of laboratory triaxial undrained shear strength for cohesive soils and standard penetration test blowcount for cohesionless soils.

Jan 1, 2008

By X. Y. Hou

The design practice of several circular underground projects with large diameter is summarized. By taking the advantages of load-bearing of circular structure, a rational annular tensile bar support system and a new design method are proposed. Calculation for a car park shows that remarkable results are brought in by this design technique.

Jan 1, 2010

By Dinesh Hinduja, Pérez: Miguel

"Large structures are generally exposed to dynamic and structural loading. They require usually either foundation connected to hard rock through sockets or driven foundations, which encounter boulders as well.In this regards drilling hard-rock sockets or boulder offshore or onshore can be a challenging job especially when deep foundations are mandatory. To overcome the challenge, specialized equipment like a Pile Top Drilling rig (PBAs) can be used, which have to be correctly set-up and operated in order to get its maximum drilling performance. High performance drilling with PBAs requires maximizing key elements of its operation. The configuration and management of the drill string components are important. The key elements are constant weight on bit which is done by adjusting ballast and managing thrust force; and selection of cutters and proper flowing discharge.The methodology is based on the experience from over 40 years of building and operating PBAs for different project applications. These applications include drilling offshore and onshore for:?Superstructures and buildings?Drilling platforms, barges and jack-ups?Harbours, jetties, dry docks and dolphins?Bridges, piers and causeways?Marine sewerage diffusers?Offshore wind farms?Dam rehabilitationMHWirth documented methodologies demonstrate that by using PBAs properly it is possible to improves performance of underwater drilling for hard-rock sockets and boulders which ultimately reduces project-cost.Background. There is a significant percentage of total project cost in structural foundations. Equipment capabilities and technics to drill shaft with rock-sockets and embedded boulders onshore and offshore are highly developed due to the dramatic equipment advancement and experience in the last 40 years. Formerly, driven piles accounted for the majority of foundations either onshore or offshore, following the experience of previous practice in the market. Nowadays, deep drilled foundations can be constructed to carry the load through the overburden down to the sound load carrying rock or soil.Scope and objectives. The overall objectives of this study are:?Synthesis information on current practices to drill shaft with rock-socket and/or embedded boulders onshore and offshore with Pile Top Drill Rigs?Identify the principal challenges evolving with practice?Provide suggestions for improvements in the construction of drilled shafts through proper operation of Pile Top Drill Rigs?Convey information through case studies and experiences"

Jan 1, 2015

By Sherif Elfass, Gary Norris

Bi-directional load testing of drilled shafts has been widely adopted as a means to evaluate their load carrying capacity. However, in order to reach failure, most of these tests are carried out on sacrificial shafts using expensive sacrificial elements such as hydraulic jacks. A proposed low-cost bi-directional testing technique is discussed. It mechanically loads the end bearing soil below a drilled shaft, against its side shear resistance. The technique was originally established as an alternative to post-grouting to reliably account for the forfeited end bearing resistance. However, since it loads the shaft in a manner similar to conventional bi-directional tests, it can be used to not only load test sacrificial shafts, but production shafts as well. Furthermore, unlike conventional bi-directional load tests, the load is applied through surface jacks. These jacks, along with other load test components, are movable and can be reused to load test all the shafts of the project thus presenting an economic benefit. The concept of this technique has received favorable feedback from a few consulted departments of transportation, and while promising, has not been field tested to date. A U.S. patent was issued for the tip loading module and the loading technique described.

Sep 8, 2021

By W. H. Craig

Techniques have been developed for installing model piles into beds of soil under high sustained acceleration levels aboard a centrifuge. These piles have been subjected to static and/or cyclic lateral loading in order to assess their performance and provide a data base for assessment of various design techniques for laterally-loaded single piles. From measured bending moment profiles the so-called 'p-y' curves have been deduced using fifth order splines for curve fitting, followed by subsequent differentiation and integration. The results show some divergence from the predictions of the semi-empirical designs, but these latter are generally found to be acceptable.

Jan 1, 2010

By Mark Brooks, Brian Freeland, Eric Eisinger

Colorado Parks and Wildlife (CPW) operates more dam and reservoir facilities in the State of Colorado than any other single entity and is in the process of completing rehabilitation upgrades to improve operational safety and modernization as required by the Office of the State Engineer. Many of these dam facilities have been operating 50 to 100 years in remote locations presenting challenges related to routine operations, maintenance, and completion of dam safety related repairs. Historically CPW has utilized design-bid-build procurement of construction services to complete these projects which presented additional challenges related to local contracting capabilities and undesirable contract disputes and claims. CPW recently pivoted to a CM/GC procurement process to contract for construction services for dam rehabilitation improvements where the remoteness, seasonal high-altitude limitations, complex topography, availability of local construction resources, stakeholder involvement, and other factors having an increased potential to negatively impact construction success and completion timeliness. The CM/GC delivery method has proven to be beneficial to the success of these projects by early construction contractor involvement as part of a collaborative Integrated Project Team to promote enhanced constructability solutions, innovations to improve quality and cost efficiency, risk identification and mitigation, and schedule and budget adherence. CPW has completed three projects using the CM/GC project delivery approach and select case histories (particularly the most recently completed Alberta Park Dam Rehabilitation in partnership with SEMA Construction) will be presented to demonstrate how this project delivery method overcame project site challenges and constraints to complete complex safety critical rehabilitation projects. The project scope on these projects included improving the capacity and function of service spillways, outletworks, and embankment stability and seepage features, and other dam safety infrastructure.

Oct 7, 2024

By Dan A. Brown

The foundations at the Huey P. Long Bridge in New Orleans presented special challenges for construction due to the requirements for very deep drilled shafts in the Mississippi River beneath the existing bridge structure. Drilled shafts were constructed to depths of approximately 200ft in alluvial soils using a rotator system with full-length segmental casing, and base grouted to improve axial resistance. This paper describes the design and construction of the work platform to provide access to the restricted-access site beneath the existing bridge, the approach used to construct the drilled shafts, and the results of a load test program to verify the axial resistance.

Jan 1, 2010

By Peter J. Jancich

This paper describes the installation of high capacity Augered Pressure Grouted piles which support structural loading from a four level parking garage in west-central DuPage County, Illinois. The subject site is characterized by a variable glacial geology which presented, to the designer, a number of problems with respect to analysis and prediction of pile capacities, and, to the contractor, the very real difficulties associated with estimating the costs of, and installing foundation units in highly variable subsurface conditions. 2. General Site and Subsurface Conditions 2.1 Site Conditions - The subject site is part of an overall 300 acre property. Topographically, the overall site is saddle shaped with higher elevations along north and south boundaries and a subdued, east-west trending swale centrally located. Elevation relief is on the order of 25-30 feet (7.6-9.2m).

Jan 1, 1991

By Madhira R. Madhav

In an alluvial deposit consisting of layers of sandy silt with clay and kankar nodules, driven cast in situ piles are provided. The piles end on a stiff bearing stratum To verify the available design capacities, compression, pull-out and lateral load tests are conducted in situ. The elastic continuum approach is used to estimate the equivalent modulus of deformation of the deposit. A comparison is made of the values from the three types of tests.

Jan 1, 1996

By Michael Arnold, Robert Bachus, Michael Bracher, Jamey Rosen, Robert Roff

"For a high hazard USACE facility, the Center Hill Dam in Tennessee, several disparate streams of data were compiled into a single geospatial and relational enterprise data management system to store, analyze, visualize and distribute the data collected during installation of a deep cutoff wall. These data streams included historical drawings and pre-construction plans and grouting records; geological data from boreholes; attributes of barrier wall elements; element verticality data analyzed from multiple measurement methods; and concrete field and laboratory analytical data. A previously developed data management system developed by the authors, WallTracker, was extensively modified to also include manually collected and real-time measurements from several types of dam monitoring instruments. The system now uses enterprise database technologies with Geographical Information Systems capabilities to manage and relate these data streams into a common platform and allows access to the raw and interpreted data via web and desktop-based interactive tools, including interactive map and cross-sectional viewers and other graphical and tabular reporting tools. One of the primary benefits of this system is the neartransparent interaction that is possible with the Nashville District of USACE on the project. These techniques can now be effectively incorporated into systems that address the unique construction and data management tracking requirements for dams, dikes, and levees.IntroductionThe Center Hill Dam rehabilitation, as with other deep foundation installations, requires the contractor to collect a substantial amount of information over the course of the project, both for internal quality control of construction progress and methods, and for demonstrating compliance with owner specifications. This paper discusses techniques used at Center Hill Dam for consolidating, visualizing and analyzing construction and instrumentation data using relational database and Geographic Information Systems (GIS) technology, collectively referred to as an Information Management System (IMS).The remainder of this paper presents the needs and objectives of the IMS, the components and data flows involved, the capabilities and user interfaces of the systems, and the benefits for the end users."

Jan 1, 2017

"Premissas BásicasCaracterísticas do concreto centrifugado(Spun concrete characteristics)Aplicação em obras de engenharia de fundações(Application engineering works foundations)Logística de fabricação e transporte(Manufacturing logistics and transportation)Emendas x uso de aplicação(Amendments x use application)Geologia brasileira, da região costeira a presença de grandes bolsões de argila mole(Brazilian geology, coastal region the presence of large pockets of soft clay)Influencia do sistema de cravação(Influence of driving system)Transferência da Energia Aplicada(Applied Energy Transfer)Estacas longas(long piles)Controles executivos (diagrama de golpes, nega, repique elástico, ensaios de carregamentodinâmico, provas de carga).(Executive Controls (blows diagram, sets, elastic rebound, dynamic load tests, load tests).)ECD – aplicação da metodologia do DIETECD - application of the methodology DIETBrazil has a highly variable geology all along its coast that directly influence the choose of foundation type, being too employed the use of reinforced spun concrete piles initially ranged in diameter from 60 to 80 cm. Over the past 10 years with the advent of investment in marine works projects began to demand a new range of piles with diameters greater than 100 cm and in the absence of amendments.On land is also very remarkable the presence of regions with large layers of soft clay, in prime areas that have been explored. A classic example is the Barra da Tijuca in Rio de Janeiro that has suffered from the housing boom growing toward these regions. In these regions it has been very common driven lengths of about 40.0 meters, which basically go through thick layers of soft material or unconsolidated and they will find strength in depth with residual soil layers or even the bedrock.The spun concrete has great qualities for application in deep cuttings resulting from the production process, which gives a redistribution of fresh concrete mass collaborating with the particle size distribution effective loss of water that is thrown to the center stake being subsequently discarded. Consequently this contributes to a reduction in the factor a/c that is directly connected to increase strength.The fact that there is a sort of concrete helps to reduce voids in the mixture, which increases the durability characteristics. This condition made it possible to employ the spin technique on poles, which are directly linked to aggressive media in large urban centers.Another very attractive feature is that the centrifuge process can work with concrete with the lowest percentage of mortar and more gravel. This concrete mix directly contributes to increasing the specific modulus of elasticity, thus allowing a greater capacity to absorb the energy of the blows transferred with less deformation.Despite the great potential of land application of prefabricated spun concrete stakes there are only three factories and its limitation is the cost of transporting manufactured for the various regions, since all transportation is done by road.For its transportation is carried out exclusively by trucks, this limits the size of cuttings being produced commonly in length from 11.0 to 12.0 meters in length and smaller compositions. For use in long piles of works is resorted to amendments in the form of metal rings, concreted near the ends of the stakes, with the transfer through steel bars in CA-50 welded to the ring. Usually run in steel ASTM A-36. Later in the work these rings are welded with coated electrode.In the case of maritime stakes are very used to drowned splicing technique, which basically consists during the spin process leave one end with the armor of the apparent stake and work together two elements and make specific, with superior resistance to the prefabricated stake.This study in addition to briefly introduce the process of manufacturing, design and logistics presents a detailed study of applicat"

Jan 1, 2015

By Florian König

It is well known that the bearing capacity and stiffness of displacement piles may increase significantly with time, a phenomenon usually referred to as set-up. In cohesive soils the set-up is commonly explained by consolidation processes in which the dissipation of the excess pore pressures around the pile leads to an increase in effective radial stresses. Recent case histories show that set-up may also occur in sand over a period which exceeds by far the consolidation process. Therefore, other effects apart from the dissipation of excess pore pressures must contribute to this long-term set-up effect. This paper presents the results of a series of multiple pile load tests on prefabricated concrete piles which capture the effect of pile set-up empirically. The main characteristics of the set-up trend are shown with respect to soil type, pile dimensions and distribution over the pile length. Possible reasons for pile set-up like consolidation and stress relaxation after the end of driving are examined using a finite element model which simulates the pile installation process.

Jan 1, 2006

By R. L. Wei

The disturbing influences of pile driving on the surrounding soil mass, including the induced vibration, pore pressure and displacement of soil, were observed during the construction of pile foundations. It is shown that the effects of pile driving in saturated soft clay are tremendous and ought to be concerned attentively.

Jan 1, 2010

By Mohammad T. Izadi

Piles are, often, used for transferring load from the super structure through soft consolidating strata onto relatively stiff uncompressible soils. Downward movement of the soft soil strata develops negative skin friction and dragload around the pile shaft, with time. Traditionally the induced dragload is considered in determining the pile bearing capacity. On the other hand, field measurements on instrumented piles show that negative skin friction is reduced by the magnitude of applied live load. A method for calculating the pile bearing capacity, driven through soft consolidating strata is presented. In this method, two allowable load-bearing capacities are calculated for each pile, live load plus dead load and dead load. The proposed method, substantially, increases the allowable load bearing capacity of piles compared to calculated values by the traditional methods.

Jan 1, 2001