Search Documents

In order to determine the optimal process parameters of agitation leaching and provide industrial process design parameters, experiments were carried out on leaching behaviors of copper oxide ore with high mud content. Condition tests show that the main factors affect the leaching efficiency as follows: Temperature, Initial acid concentration, leaching time and particle size. As the temperature increases, the copper leaching rate was increased. At 60 ?, the initial acid concentration 80g / L, leaching time 2h, liquid-solid ratio 2:1 and grinding fineness65%-0.074mm, the optimal copper extraction was 83.15%, the acid consumption was 187.91kg / t. ore. Keywords: agitation leaching, copper oxide ore, mud

Sep 1, 2012

By V. Hudecek

Problems of sudden outbursts of rock and gas present in deep mine mining ones of the most complicated interrogation. It is searching for the methods of prediction and prognosis that can be most useful for the government of these phenomena. Till now the pressure and the desorption of gas in bore holes was consider to be the decisive criteria. By the work of authors with using of statistical date was verify that for considerable reliability of forecast and prevent outbursts is necessity investigate characteristics of workplace and other indicators. These indicators were analyzing and assemblage into mathematical dependences which represent active and passive force asserting with in the process of rush. It was validated by using the equations which are presented in the manuscript that the accuracy of pre-diction of the phenomena is higher and methods of preventions are better also.

Jan 1, 2014

Flinders Power, formerly NRG Flinders, is considering the possible use of low rank coal from Lake Phillipson, South Australia (SA) in its power stations at Port Augusta, SA. Typically, this coal contains about 35% moisture and 10% ash. Unfortunately, it also contains high levels of sodium (1% Na) and chloride (0.95% Cl) with a Na2O level in ash of 18.9%. Such levels cause serious problems during coal combustion, making the use of as-mined coal impractical for power generation. This paper describes the development of an aqueous leaching technique to remove 90% of the sodium and chloride and to yield a product with a Na2 O level in ash of less than 3%. Small-scale agitation leaching tests with good quality tap water at ambient temperatures showed that the coal needed to be crushed to minus 5.6 mm to obtain maximum removal of water-soluble sodium and chloride in 30 min. Leaching kinetics, but not the ultimate removal of salt, were enhanced by the use of higher temperatures (up to 150°C), but this was deemed uneconomic. Varying the pulp density between 20% and 50% had little effect on extractions and there was no benefit in multiple stage water washing. The best results by water leaching were 69%~74% extraction for sodium and 95%~97% for chloride, meaning that the sodium removal was well below the target level. From SEM examinations of the leached product it was concluded that the remaining sodium was organically bound to the carbon atoms in the coal. Further tests using aqueous solutions containing cation exchange additives such as calcium chloride (CaCl2) or ammonium chloride (NH4Cl) or sulphuric acid (H2SO4) showed that significantly enhanced sodium extractions were possible and target specifications were met. Two options, namely a single-stage and a two-stage leach, were then investigated. In a single-stage leach with additive, minus 5.6 mm coal was leached at 33%~50% solids for 30 min at ambient temperature and then filtered and washed with fresh water. This gave a sodium removal level of about 81% and a Na2O level in ash of about 5%. These levels do not quite meet tar-get specifications. In a two-stage leach, the coal was first leached with water alone without an additive as in the single stage leach, and the washed residue re-leached under similar conditions for about 5 min with an additive (CaCl2), and then filtered and washed. This gave a cumulative sodium removal of 96% and a Na2O level in ash of 1.4%~2.4%. These levels are well within target specifications.

Jan 1, 2014

By A. S. Choudhary

Most of the coal reserves in India are of drift origin and have very poor washability characteristics and a high level of near gravity materials. At least 30 new coal wash plants are expected to be set up in the next 5years.In such a scenario, adequate sampling followed by sink float test work for washability analysis becomes very critical for designing these new plants. For coal sampling purpose, stipulations of different standards are sometimes formidable and on the border of ?impracticality?; sometimes are self contradictory in terms of gross sample weight vis-a-vis minimum number of particles required in each size fraction and in each relative density fraction and also the minimum mass in the latter. Validation of the generated data is another important aspect of washability analysis. These issues can easily be addressed by using straight forward mathematical relationships, well known RR plots and by using simple MS Excel tool, etc.

Sep 1, 2012

By P. Raghavan1

Reverse froth flotation experiments were carried out in the laboratory using two different types of kaolins for the separation and removal of coloring titanoferrous impurities from cryo-filtered clay after subjecting to high shear pre-treatment. This high shear pre-treatment consists of high shear agitation of a high solids clay slurry with the dispersant (high shear dispersion, HSD) followed by high shear agitation with the collector (high shear conditioning, HSC). After this pretreatment, the slurry is diluted and reverse flotation is carried out. One sample is from, Gujarat, India (Mamuara clay, ?MC?) while the 2nd sample is from Amberg, Germany (AKW clay, ?AC?). While MC consisted of 89% particles below 2µm and analyzed 1.06% of TiO2 and 0.29% Fe2O3 and measured a brightness of 83.4 %ISO, the corresponding values for AC are 67% below 2µm, 0.3% of TiO2? 0.49% Fe2O3 and 83.4 %ISO. The flotation performance is found to be greatly influenced by the conditions of high shear treatment. Important variables are HSD intensity (rpm), HSD time, HSC intensity (rpm), HSC time, HSD/HSC time ratio, ?HSD+HSC? total time etc. Higher shear intensities favor both the impurity liberation and collection. For both clays, it could be shown that impurity removal increases as total pretreatment time (?HSD +HSC? total time) increases up to a certain limit. For MC, the HSD time was only half or less than that of HSC time, while for AC, HSD time is at least twice (or more) than HSC time which is just an opposite manifestation. This is believed to be due to the striking differences between these two clays. Most importantly, the shear frequency is found more influential than the shear rate for the overall flotation performance for both clays. Interestingly, at high shear frequencies, i.e., when a stirrer with more number of teeth on the rotor is used, the ?HSD+HSC? total time is greatly reduced. Again, increased shear frequency helps to reduce flotation time and significantly improves flotation performance. At optimum conditions, product titania reduced to 0.35% for MC whereas the same reduced to 0.13% for AC. The product of flotation of MC measured 85%ISO brightness while that of AC measured84.6%ISO thus enhancing the value of the final product. It could also be established that the high shear pre-treatment shows better flotation performance than that due to collector dosage. Keywords: high shear dispersion, high shear conditioning, titanoferrous impurities, shear rate, shear frequency, brightness, clay recovery, Mamuara clay, AKW clay

Sep 1, 2012

By Matti Kongas, Kari Saloheimo, Antti Remes

"The paper studies the control performance of the flotation process as a function of the measurement accuracy and sampling frequency of an on-stream XRF analyzer, using a simple dynamic model. An additional aim is to assess how the economical result of a mineral flotation process depends on the quality of process control based on the on-line elemental assays.An on-stream XRF analyzer measures the concentrations of slurry lines in a continuous cycle from several process points. The control performance depends on the analytical accuracy and sampling frequency of the concentration measurement. With a long cycle time, the state of the process changes before a new measurement becomes available. With short measurement times the statistical variance of the counted X-ray pulses increases, increasing the random error in the analysis. In addition, the measurement accuracy depends on the concentration of the component to be measured from the slurry.To quantify the effect of analysis error and frequency to process control, a simple dynamic process model is created in the Matlab environment. Data from a copper flotation circuit is used as a test case. The process model comprises a first order reaction equation and the grade-recovery -relationship estimated from process data. The control was modeled using the control strategies implemented into a rule based advanced control system.The economical performance of the control was studied by calculating the overall net smelter return at various analyzer parameter combinations. The economical performance of the process declines strongly when the sampling cycle is increased. In studied case the sample measurement time did not have a significant effect on the results. The economical performance of the simulated process corresponds to an almost uncontrolled process when sampling cycles longer than 40 min are applied."

Jan 1, 2003

By Mohammad Noaparast, Hamed Haghi

"In this research work, it was attempted to reduce the iron contents (Fe2O3) in relatively low grade silica sample which was obtained from Shenin silica mine, using magnetic separation. The prepared sample contained 93.75%SiO2, 0.44%Fe2O3, 2.78%Al2O3, and 0.08%TiO2 and the Fe2O3 had to be reduced to less than 0.08%. Mineralogical studies and XRD analysis indicated the presence of Hematite, Pyrite, and Goethite as the major iron impurity phases. Mineralogical studies of polished and thin sections demonstrated that the degree of freedom of silica is more than 80% in -300+212 ?m size fraction. After primary stages including crushing, milling, scrubbing and de-sliming, various methods such as low intensity magnetic separation (LIMS), high gradient magnetic separation (WHGMS) and dry high intensity magnetic separation (DHIMS) were applied to find out that which process would be appropriate for the elimination of iron impurities from this sample. Different experiments were carried out on the product of wet rod mill and scrubber. However the magnetic field intensity of WHGMS was increased down to 2Tesla, and there was not any acceptable result in reduction of Fe2O3 content lower than 0.08%. Thereafter the product of wet rod mill and scrubber were dried and reported to DHIMS. In these experiments, maximum magnetic field intensity was 1.4Tesla. In this case very significant results were achieved, and Fe2O3 content of final product were reduced to less than 0.05% which meets glass manufacturing standards."

Jan 1, 2014

By Katja Ohenoja

Polymer dispersants, also known as grinding aids, are widely used to reduce the viscosity of mineral particle suspensions and to improve energy efficiency during fine grinding. In this study, the effect of polymer dispersant with different molecular structure on the suspension properties in the wet stirred media milling of limestone was studied. The stability of suspension was studied by combining rheological and zeta potential measurements. The PDI value of polymers corresponds to the width of the molecular weight distribution so that low PDI corresponds to narrow MW distribution and high PDI to the wide one. In this study, two traditionally fractionated polymer dispersants with high PDI (over 2) and one novel polymer dispersant with low PDI (1.2) has been tested. It was noticed that dispersants worked as electrosteric stabilizators and prevented the agglomeration of ground limestone particles. The uses of dispersants could increase solids concentration used in the grinding experiments and at the same time lower the particle size and specific energy consumption. The obtained particle sizes were about 1 µm regardless of which dispersant was used or the amount of it. The novel dispersant with low PDI reduced viscosity most when compared with the traditionally fractionated polymer dispersants. Results indicated that even higher solids concentrations can be used at the same amount of dispersant when the novel low PDI polymer dispersant is used. Alternatively, lower dosage of novel low PDI dispersant can be used compared to traditionally fractionated dispersants.

Sep 1, 2012

By F. S. Niu

With the feature of finely-dissemination particle and complex mineral composition, oolitic hematite is considered to be the ore dressing difficult problem in the world. Series research on refractory oolitic hematite in Zhangjiakou Area are introduced as following: ore properties?technology mineralogy and mineral processing technology. The survey shows: with the fine grinding of the hematite to a fineness of -0.076mm 95%, obtaining iron concentrates grading 62.74% Fe at the recovery of 46.80% by high intensity magnetic separation- reverse flotation flowsheet; under the three stages intensity magnetic separation,four stages grinding and four stages gravity separation, getting the iron concentrates grading 61.09% Fe at the recovery of 45% using high intensity magnetic separation- gravity separation flowsheet; with roasting temperature of 800°C, time for 75~90min and ore-coal ratio of 11, gaining the iron concentrates assaying 62.74% Fe at the recovery of 87% by roasting- magnetic separation flowsheet. At present, this research is still doing for the target of raising the concentration recovery on the base of high grade concentrate. It is in the hope of fully utilizing the existing hematite resources in Zhangjiakou

Jan 1, 2014

By S. V. Petrov

Oxidised ores possess a significant share among raw materials which are treated by traditional plant technology. As usual, the chemical composition of these ores is rather simple. They can be treated by standard cyanidation. In this case, the resulting wastes have an alkaline reaction. Their toxicity (in case of ROM ores treatment) is mainly due to the presence cyanides and thicyanades. The tails are dexotified before disposal. However, chemical reagents used cannot provide a complete removal of toxic matters. In this case, this disposal poses a real problem because these tails contain a significant amount of CN and SCN and their behavior during a long disposal should be studied. A sample with a simple composition taken from cyanidation tails was studied. The sample presents itself the quartz low-grade sulfide gold-bearing ore. Sulfide sulfur content is 0.15 per cent,and heavy metals content is 0.023 per cent. Method of testing is described further. The samples were tested under moderate and subarctic climates based on the difference in temperature, moisture and the degree of oxygen saturation of air. The pH of water extract, which was prepared using distilled water, was also determined besides measuring the concentration of cyanides and thiocyanates. This demonstrates the stability of sulfide-bearing minerals in the disposed tails. The tests time was 820 days. It was found that the alkalinity of the samples tends to lower under oxygen-containing conditions in proportion to temperature increasing. Under conditions without oxygen, the pH lowering is minimal. Mineralogical and chemical properties of the ore material give positive alkaline balance during testing. The solid sample contains enough alkaline agents to compensate dangerous to the environment reactions of sulfides oxidation.pH value maintaining under alkaline conditions witnesses to the possibility of a safe disposal of this tails type. The largest amount of cyanide is removed under acid-containing conditions at positive temperatures. The higher the temperature is, the more intensive destruction is. At the moment, of finishing the tests at 20ºC temperature, the residual concentration of CN- was 0.06-0.10 mg/L, at 4ºC, the residual concentration of CN- was 0.2-0.3 mg/L and at -18ºC was 0.4-0.6 mg/L. Under conditions with the lack of oxygen, cyanides can be removed within the first 200 days. Then, this process fully stops. A stabilized cyanides concentration is 3.0-4.0 mg/L. The presence of sulfides increases the content of cyanides at the initial stage of testing. Then, the concentration of SCN at the temperatures above 0ºC decreases rapidly under oxygen-containing conditions. At the rise of temperature, a narrowing of peak at the curve and an increase of the destruction process are observed. At the end of testing, the concentration of thiocyanates in the moisture of wastes was 0.2-0.3 mg/L at the temperature of 20ºC and 0.5-0.6 mg/L at the temperature of 4ºC, respectively. The concentration of thiocyanates contained in a frozen sample and media which have the lack of oxygen stabilizes at a certain level owing to sulfides and does not practically change further. It was found that detoxification of oxidized cyanidation tailings with a simple composition which were disposed as filtration cakes can be possible. In this case, the concentration of cyanide in the moisture of disposed wastes can have a close value or equal to actual concentration during cyanidation. In order to meet the requirements of high ecological safety standards and successful detoxification process of toxic compounds in the tails under the action of natural factors, the conditions of air aeration with oxygen for the whole volume of tails are required. Keywords: cyanides, thiocyanates, storage, detoxification, flotation cakes

Sep 1, 2012

By E. Guerrini, M. Maccagni, J. Nielsen

"Lead is the most important material able to meet the current demand for energy storage. The lead acid battery is reliable, efficient and inexpensive. Continuous developments in battery construction are providing improvements in all aspects of the batteries’ performance. The lead acid battery is both the main lead product and the main raw material for lead production. More than half of the lead produced is from secondary smelters where batteries are the most important feed material. The environmental pressure on lead production has been increasing for many years, and continues to become stronger and stronger. The lead production processes and technologies themselves will require updating to meet the new regulations. Although they are very strict now, they will become even more so and current technologies may not be sufficient. Because recyclability is a strong point for the lead acid battery, the secondary smelters need to reduce the environmental impact as much as possible. In recent years, the secondary smelters underwent impressive changes in this direction, but some more improvements are possible. Electrochemistry can offer a step change improvement in making secondary lead production more environmentally friendly. Engitec has developed an electrochemical process base on a very high current density (high productivity) cell using an inexpensive electrolyte and at a relatively low cost. In this paper, the latest update on the technology is provided. INTRODUCTION The lead acid battery is considered the “walking dead” by some new technologies trying to replace it. It has played and will continue to play a very important role in our lives because it is inexpensive, fully recyclable and the existing lead and the mine reserves guaranty enough material for the extended future. According to the life cycle, the lead acid battery is the cheapest and the most effective system to store energy. Lead is practically a close loop where lead battery production consumes more than 80 % of the produced lead but contemporarily it is the most important raw material for the production of metallic lead. In fact, nowadays, the secondary production has overcome primary production and this trend is expected to continue. Primary lead is the make-up material for the existing battery production and the source of lead for the construction of the new ones."

Jan 1, 2018

By G. Deschênes

In the last 4 years, the high price of silver attracted more interest for improving its extraction. Metallic silver and silver minerals require a high concentration of cyanide and show slow leaching rates and poor extraction. This investigation determined the effects of dissolved oxygen, lead nitrate and a pretreatment on silver leaching from slurry containing quartz mixed with metallic silver and high purity acanthite. Stephanite, pyrargyrite and polybasite were also used in the study. The silver minerals were characterized by chemical assay, X-ray diffraction analysis (XRD), image analysis (MP-SEM-IPS) and electron microprobe analysis (EMPA). Increased dissolved oxygen of the slurry produced the fastest silver leaching kinetics. The leaching of silver from high purity acanthite was determined under various conditions and compared to a new process called ?CANMET Enhanced Leaching Process (CELP). For a slurry containing acanthite, a 23% improvement (from 76% to 99%) in silver extraction was obtained with the CELP. In presence of pyrargyrite and polybasite, silver extraction increased from 75% to 90% and 86% to 99% respectively using the CELP. No improvement was obtained for the slurry with stephanite (99% extraction in 72 hours). However, the sliver leaching rate was much faster with the CELP. XPS analysis of individual silver mineral particles showed that CELP leached surfaces were considerably more oxidized relative to the conventional cyanidation leached surfaces. Leaching of two gold/silver ores indicated that the efficiency of the CELP increased with the refractoriness of the sample. Gold extractions were comparable for the two technologies while silver extraction improved up to 5% (70g/t) for the CELP. The final leach solutions contained lower concentrations of copper, which consequently reduces the effluent treatment costs.

Jan 1, 2014

By Z. Y. Lan

Bioleaching of marmatite with various mixed cultures of microorganisms was investigated. The experiments were carried out in shaking flasks with iron-free nutrient and the pulp density of 10% wt/vol at the temperature of 30?. The results show that zinc is preferentially leached before iron. The leaching rate of zinc with the mixed culture of Acidithiobacillus ferrooxidans, Acidithiobacillus thiooxidans and Leptospirillum ferrooxidans is 62% in 18 days. The leaching rate of zinc with the mixed culture of Acidithiobacillus ferrooxidans and Acidithiobacillus thiooxidans is nearly the same as that with the mixed culture of Acidithiobacillus ferrooxidans and Leptospirillum ferrooxidans (45% versus 50%). SEM and EDX analysis of the leaching residues indicate that a solid product layer composed of iron sulfide, elemental sulfur and jarosite accumulates in the mineral surface and becomes a barrier to the dissolution of marmatite. The bioleaching of marmatite follows the shrinking core product layer model. When the product layer increases and becomes insoluble, the leaching rate is controlled by the diffusion through the product layer and slows down. When the product layer decreases or becomes a porous layer, the leaching rate is controlled by chemical reaction and enhanced dramatically.

Jan 1, 2014

By B. Orberger, J. M. Milazzo, S. B. Blancher, J. Lützenkirchen, J. L. Dubos

"Industrial dusts are commonly agglomerated using empirical recipes with binders such as bentonite, while Sludges are agglomerated into mixes. Those materials contaminate the products, are expensive and generate significant amounts of slag. Achieving cold dust agglomeration with little or no binder requires understanding the controlling parameters in order to predict and optimize the process behavior. This in turn necessitates comprehensive dust characterization to base predictions on measurable characteristics. In the present work we collected 13 Mn-rich dusts over all the process chain: feed fines, smelting, and refining dusts, as well as ferromanganese alloy dust. This is the first systematic study of dusts along the Mn-processing chain for chemical, physical and mineralogical parameters. X-Ray Diffraction, Qemscan® and laser granulometry analyses show that the mineralogy, Particle Size Distribution (PSD) and morphology evolves from complex heterogenous to simple, homogenous along the process chain: The mineralogy of the primary ore dusts shows various hydroxides, oxides, carbonates, tectosilicates and phyllosilicates. The furnace dusts contain oxides, tectosilicates and carbonates with volatiles, while the refining dusts present only oxides and metal. Finally, the Metal dust is nearly pure metal. Particle morphologies and PSD vary from jagged, irregular particles with broad PSD (>1 mm to <0.3 µm) to smooth and spherical with narrow PSD (100 µm to <0.3 µm). The Metal dust is an exception with angular particles. The Cationic Exchange Capacities (CECs) of all samples range from 0 to 22 meq/100g. Specific surface areas (SSAs) range from <0.1 to 27m²/g, and seem to decrease with from ore feed to Metal dust. This may be due to the disappearance of hydrated and/or sheet-bearing minerals, since a smaller grain size usually implies an increased SSA. The zeta potential varies strongly over the range of the samples tested. However, beside the Gabon ore which has an Isoelectric Point (IEP) ~ 4.1, the other IEP ranges between 2 and 2.5."

Jan 1, 2018

By Sushanta Majumder

The physico-chemical characteristics of raw materials used for the production of iron ore pellets have a strong influence on the productivity of pelletization operations and on the quality of pellets. Since iron ores from different sources are used for making iron ore pellets and since the quality of the ores varies with time, there is a need to optimize and control pellet plant operations on a regular basis to achieve optimum productivity while maintaining pellet quality within the desirable specifications. In order to achieve this objective, a model-based on-line optimization system was implemented on two industrial scale induration furnaces. The optimization system consists of a rigorous mathematical model of the induration process, a model for the permeability of the bed of pellets, a statistical model for the quality of iron ore pellets and an optimization module based on sequential quadratic programming. The rigorous model is tested on-line using the wind-box temperature available real-time. The process was optimized to enhance induration furnace productivity for the given constraints on pellet quality parameters such as the cold compressive strength (CCS) and Tumble Index (TI), and other equipment design parameters. Process variables such as induration machine speed, cold air flow rate and hood temperature profile were used as the optimization variables. The on-line optimization system was successfully implemented in two industrial induration furnaces and lead to enhanced productivity. Details of the on-line optimization system and results of process optimization will be presented.

Sep 1, 2012

By A. A. Rogozhin, E. G. Likhnikevich, S. I. Anufrieva, A. V. Kurkov

"Russia is among the nations holding the world's largest lithium ore reserves. Lithium is of key importance for the global economy. Therefore, it is important to review the current state of technology research aimed at finding the most effective solutions for the recovery of lithium from promising reserves in Russia. In Russia, a number of process solutions for the flotation of spodumene into salable concentrate (5% Li2O) have been implemented at the earlier existing complex low-grade ore concentration project. By applying these solutions, a sample of high-grade spodumene ore (4.7% Li2O) of the Greenbushes deposit was processed into a spodumene concentrate (7.5% Li2O) at a high recovery (~93%) of lithium. In Australia and Canada, new processes have been developed for the recovery of high-grade spodumene concentrates from high-grade ores using dense medium separation and flotation. For the recovery of mica lithium concentrates from low-grade ore, a flotation process was developed in Russia using the cationic collector ANP-2 and Oxifos-B as an additional collector. Low-grade ore containing 0.14% of lithium oxide was processed into a 2.7% Li2O concentrate. New hydrometallurgical lithium concentrate and ore processes are developed to avoid high-temperature (>1000 °C) roasting. The Sileach process (Australia) includes leaching of lithium ore with sulfuric acid in the presence of a halogen-containing component at a temperature of 95-115 °C. In the Russian process, lithium is recovered into an alkaline solution from low-grade spodumene ore in a pressure alkaline leaching environment (250 °C, NaOH concentration > 300 g/l). The developed concentration and hydrometallurgical methods will allow to design on their basis efficient processes for recovering salable products for hi-tech industries from lithium ores.INTRODUCTION Lithium has many unique and important properties. It is the least dense hard metal. Its alloys have some of the highest strength-to-weight ratios. Lithium has the lowest melting point of all known solid elements and is used as a highly-effective heat transfer medium. The high demand for lithium is due primarily to its unique electrochemical potential and low thermal expansion coefficient. It is used in the production of glass and ceramics, in petrochemicals, metals, medical and other industries. Since the late 20th century, the electronics industry has been the largest consumer of lithium. In recent years, lithium has attracted much attention also as an important component of ultra-lightweight electronic devices. It is also the preferred metal for electric batteries used in mobile electronic devices, vehicles, household power generators, making it an important resource for the development of environmentally friendly technology. Leading automotive brands have ambitious plans for the production of electric cars — Tesla Motors, VW, Toyota, GM, BYD Auto. It is expected that the production of electric vehicles alone will triple the demand for lithium by 2025. A sharp increase in the production of lithium is expected. Lithium has all the prerequisites to become a strategic resource of the 21st century. (Deutsche Bank, 2016; Bradley et al, 2017)"

Jan 1, 2018

By Zhou Junwu, Han Long, Song Zhenguo, Sun Chuanyao

The deposit genesis, the ore property, and the mineral characteristics, which has a close relationship with the beneficiablity, could be regarded as the “Genetic Properties”, actually are the determining factors for beneficiation process development. However, in conventional concentrator’s process development and engineering, there have been lack of systematic research and test on those genetic properties, also lack of well-established collecting, statistics and analysis system for those huge amount of data such as the historical mineral processing technique research, process mineralogy study, practical operating and engineering data. Obviously it is far less than enough for profound integration combining modern IT together with traditional mineral processing technology, as a result there are a number of disadvantages in mineral processing R&D and engineering, such as long term, high cost, low efficiency as well as repetitive testwork not making full advantage of previous experiences. Aiming to make utmost of those Genetic Properties and overcome above disadvantages in mineral processing R&D and engineering, the concept of “Genetic Mineral Processing Engineering (GMPE)” is put forwarded, and the strategical study has been conducted on this regard, with the main focus on following aspects: a) Testing and extraction of the “Genetic Properties”; b) Establishment of data base and data warehouse of GMPE; c) Intelligent decision making system for beneficiation process; d) Verification testwork; e) Virtual concentrator. The technical route proposed is to firstly conduct research and test on those Genetic Properties mentioned above, based on that the specific data base will be set up and applied for intelligent process recommendation and simulation with a few verification testwork conducted in the meantime, finally achieve a fast, high efficiency and precise determination of technology and process for ore beneficiation. The systematic study on the three-in-one GMPE would make an innovative breakthrough in conventional mineral process testwork research and engineering methodology, and provide technical support for the concentrator’s design and upgrading.

Jan 1, 2018

By H. M. Gao

According to the difficulty of dolomite removal from collophanite,normal-reverse floatation process has been adopted in floatation with the use of highly selective collector G-4 and depressant S721. Good indexes of flotation have been obtained with the run-of-mine ore containing 17.96 % P2O5 and 2.31 % MgO being upgraded to a concentrate containing more than 30% P2O5 and less than 1% MgO. The reagent interaction mechanism in low grade collophanite flotation has been stu-died by FTIR analysis and theoretical calculation. The results indicate that the interaction between collector G-4 and collophanite is the result of chemical adsorption in combination with physical ad-sorption with chemical adsorption playing the major role. Depressant S721 adsorbs on dolomite surface to form a water film and effectively depresses the flotation of dolomite and reduces the MgO content in the concentrate.

Jan 1, 2014

By Ajay K. Jha1

Drilling and Blasting are two important unit operations in the production cycle of a mine and a strong link exists between these two and other unit operations/subsystems like loading, transportation, and crushing. Under the present concept of ? Mine to Mill?, it is important to optimize the drilling and blasting operations by applying scientific approach to drilling and blasting using sophisticated instruments and new technologies, which depends heavily on Information technology (IT) to meet this imperative. Development of innovative models and software has lead to blast optimization process. Till date, the blast results are evaluated in terms of available empirical approaches like powder factor, which are too simple to exclude some key parameters or lack in providing reliability because of non-availability of user friendly IT enabled techniques. Although with the help of developed approaches, formulation of user-friendly software to assist the site engineers in effective post blast assessment has started but there is a dearth of holistic approach to design an optimum blast considering the techno-economic feasibility of the subsystems and the geo-mining conditions to achieve blast optimization. The science of IT enablement in drilling and blasting is capable to build innovative models for achieving blast performances which will be doped with productivity, economy and safety with due regard to environment. The present paper discusses the use of existing IT enablement in various mines of India citing the Indian scenario and the future requirements for achieving the techno-economics in overall mining operations.

Sep 1, 2012

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, A. Abazarpoor

"The morphology of pellet feed is known to influence several properties of iron ore pellets, including drop number, compression strength and reduction properties. The effect of grinding method on the particle size, specific surface area and particle shape of an iron ore concentrate has been studied. Grinding methods considered were ball mill and high pressure grinding rolls (HPGR). 5 different samples (Blaine= 1800, 1900, 2000, 2100 and 2200 cm2g-1) were used to compare the size, shape and specific surface of particles for each grinding methods. Particle size was meticulously examined by sieve analysis, laser sizing and image analysis. In samples ground by ball mill, it has been observed that the fraction of particles <10µm increases from 39% to 46% as the Blaine number increases from 1800 to 2200 cm2g-1. For HPGR samples, corresponding figures are 41% and 49% respectively. It is evident that for samples ground by HPGR, the fraction of fine particles is higher than that of those ground in the ball mill. To measure the specific surface area of particles, Blaine and BET were used. A higher real surface area was observed from HPGR treatment in comparison to ball mill grinding, provided by a higher porosity, cracks, roughness and new surfaces. Shape factor of particles was determined using three descriptors: circularity, roughness, and aspect ratio. It was also observed that particles produced by HPGR were more elongated, less circular, and rougher than those processed by the ball mill. 1. INTRODUCTION Particle size and shape are important parameters that can significantly affect mineral processing plants and pelletizing plant performances (Brozek and Surowiak, 2007). It has also been proposed that green pellet quality is directly related to the amount of fine particles in a pelletizing plant (Dwarapudi et al., 2008; Umadevi et al., 2008; Gul et al, 2014; Van der Meer, 2015). Particle size distribution and specific surface area (SSA) are also key factors that can control the quality of green and fired pellets. Processing circuits generally reduce the fines fraction to lower than the required specific surface area (SSA). It is therefore necessary to regrind concentrates to produce suitable pellet feed for further treatment in the balling and firing steps [1, 2]. Two main methods are used for re-grinding of concentrate; high pressure grinding rolls (HPGR) and ball mill. Given the different forces used to reduce size in these methods, it is expected the shape of particles will be different (Pourghahramani and Forssberg, 2005)."

Jan 1, 2018