Search Documents

By Francis O. Otuonye

A time series and system analysis modeling technique was applied to signals from strain egages mounted on a fully grouted resin roof bolt and signals from accelerometers mounted on the bolt head and roof rock to determine the roof bolt's response to repeated blast loading. The derived model gives a comprehensive quantitative description of the modes of vibration of the roof bolt response to each blast loading. The damping ratios and natural frequencies of the modes of vibration can reveal the alteration of the process dynamics due to the deterioration of the roof rock and can be used to identify the incipience of instability in the roof bolt system.

Jan 1, 1987

By Ron Woolf, Corry Goumans

This paper describes rock slope remediation performed along America’s first Superhighway, the Pennsylvania Turnpike and in particular, the specialized drilling equipment designed and built by Pacific Blasting to complete this work. This S-month project was performed on an existing rock cut slope within the Bedford Narrows, a gap formed by the Juniata River through Evitts Mountain. These rocks are in the folded Juniata and Tuscarora Formations within the Valley and Ridge Province and strike northeast with near vertical to slightly overturned bedding.

Jan 1, 2001

By W. Birch, G. D. Rangel-Sharp, L. Bermingham

For many years, the accepted method of Measuring the Velocity of Detonation (VOD) in blast holes has been to use an electric cable of a constant resistance per metre. Thus as the wire is consumed by the explosive in the blast hole, the change in resistance is monitored and when this data is plotted against the time period of the in hole explosion, the VOD can be calculated.

Jan 1, 2011

By R Vuolio, B A. Jonsson

In the center of Helsinki - capital of Finland - extensive blasting operations were carried out during the years 1982 - 84. At the corner of the streets Mannerheimintie and Simonkatu - in the Forum block - about 125,000 cu.m. of rock were blasted to give place for a new modern shopping centre (Fig. 1). Added to this amount of rock another 10,000 cu.m. were blasted for a transport tunnel to an adjacent underground bombshelter (Fig.2) which is to be used as a parking place in peace-time. The blasting work was demanding and difficult to carry out due to old buildings surrounding the work-site as well as computers and other sensitive equipment installed in some of them.

Jan 1, 1985

By Tristan Worsey, Nathan Rouse, Daykin Schnell

The authors were retained by a proposed underground metals mine operation to evaluate the potential blast vibration amplitudes that could be generated at surface structures above the proposed mine. Literature reviews of published blasting documentation gave little information, data, or models on surface blast vibrations produced by underground mines. At the client’s request, the authors contacted a number of underground mining operations to evaluate interest in sharing blast vibration data with the authors so that the authors could develop an underground-to-surface blast vibration regression equation. The authors worked with three underground metals mining operations to collect surface blast vibration data produced by heading blasts and stope blasts. The data included blast vibration amplitude values, seismograph records, blast design geometry, charge weights, and detonator delay and sequence designs. The total amount of information was used to produce a regression equation and summary dataset that could be used by the proposed underground mining operation to evaluate blast vibration amplitudes that will be generated on the surface. This work is published and presented so that operations with proposed underground mines or proposed underground mine extensions can use these equations to predict vibration amplitudes on the surface above the mine workings before any blasting occurs.

By D Vrkljan, Z Ester

Excavating the building pit for the World Trade Center at Rijeka, it was necessary to blast over 160000 m3 of hard mass in fused condition. The building pit is located at a densely populated residential part of the main Croatian port Rijeka, close to the railway-track and traffic routes of the town. The permanent seismic monitoring points are foreseen on endangered housing and infrastructure facilities around the pit during designing and excavation of it. The seismic monitoring has been performed on 15 permanent points by occasion of over a hundred production and continuous blasting operations. The article considers the speeds of ground oscillations depending on applied maximum quantities of explosive charge according to fire degree, total quantities of explosives at the mine-field, structure of explosive charge, applied delay of mine boring and lines initiation mode and rock mass structure

Jan 1, 1999

By Paul Worsey, Gerald Rupert, Mark Kirkbride

The realignment of Highway H in the proximity of Crystal Cave (Springfield MO.) required the development of a blasting program that was both economical and efficient for construction, yet ecologically safe for the cave. Three component seismographs were strategically placed underground near prominent and sensitive cave features and the vibration levels from the construction blasting continuously monitored. Peak particle velocity (PPV) values were found to obey the square root scaling law and a peak particle velocity value of 0.3 in/sec was chosen as the safe maximum limit. This value proved adequate in preserving the integrity of the cave and its features. Scaled distances for the maximum and lower values enabled blasting personnel to select explosive charge weights per delay for given distance to the cave. Delays were determined from the dominant frequencies recorded underground.

Jan 1, 1997

By Ingvar Hansson, Bjorn A. Jonsson, Bernt Larsson

In the Kiruna Research Mine, Sweden, four large open stopes have been mined, leaving intermediate piIlars and crown pillars. At the final stage of mining mass blasting of the crown pillars above two of the stopes was carried out. The crown pillars contained some 290,000 tons of iron ore. In the mass blast a new initiation technique was used, utilizing the new non-electric system NONEL ? UNIDET. The blasting technique including vibration control is described. The mass blast resulted in high recovery, good fragmentation and low vibration levels.

Jan 1, 1986

By Thomas R. Scotese, John L. Ackerman

The Hanging Lake Tunnel Project represents a major portion of the Glenwood Canyon Project, the last piece of Interstate 70 to be constructed. The project features twin bore, large span rock tunnels and six open cut portal excavations, all excavated by drilling and blasting. This paper presents descriptions of the methods used by the Owner and Engineer to control and monitor the drilling and blasting practices in the tunnels and in the portal areas.

Jan 1, 1992

By Walt Meglasson

The Kaiser Aluminum Company Smelter, one of several in the Pacific Northwest, was built in 1942 and operated by the Olin Company during World War II and then purchased by Kaiser Aluminum after the war. At its height, the facility employed over 350 workers and was capable of producing 73,000 tons of aluminum per year. It was closed in 2000 through a combination of rising electrical and labor costs, and the inability to compete with more up-to-date foreign facilities.

Jan 1, 2008

By Jean-Francois Lagueux, Andre Pomerleau

Goldex Mine is an underground mine located near the town of Val-d’Or. Multiple innovations were required to work the mine. Due to its low grade, it was important to develop a bulk mining method to economically extract the ore. The method used is a combination between shrinkage stope and long holes stope methods. This modified method is more than adequate; however, all of the ore body must be liberated in a very short period of time. Therefore, to bring down 23.0 M tonne (25.3 M ton) of ore, large blasts up to 1.8 M tonne (2.0 M ton) are required. The situation is also complicated by the fact that the mine is located in a residential area. No less that 40 homes are built within a 1 km (0.62 mile) radius of the mine site.

Jan 1, 2011

By Philip M. E Thomas

For over sixty years man has struggled to defeat the natural swamp lands known as the Florida Everglades as demand for land to support the burgeoning population growth in the state continued almost unchecked. Over the past ten years there has been a growing awareness that this land development could wipe out a whole ecosystem in a very short time unless steps were taken to reverse the trends. In 1991, a state law called the Marjory Stoneman Douglas Everglades Protection Act was enacted giving power to the South Florida Water Management Board to condemn certain lands for conversion to manmade swamp lands, designed to filter polluting run-off water from the agricultural lands around Lake Ockeechobee.

Jan 1, 1994

By Kenneth Medearis

The accurate prediction of possible damage to historic structures subjected to blasting-related ground motions is not infrequently the dominant factor in whether or not a mining or quarrying operation is allowed to proceed. A recent scenario involving an 1802 Pennsylvania Historic House was resolved satisfactorily, primarily because of the use of modern structural dynamics analysis techniques rather than simplistic peak particle velocity guidelines. One of the associated dominating factors was the truly significant agreement of the analysis results and the values obtained from actual on-site test shot blast motion recordings.

Jan 1, 1993

A case history is presented where a variance was permitted by the court to change a 500 foot limit to 250 feet for blasting overburden at a surface coal mine in the proximity of a historic structure.

Jan 1, 1991

By Oldrich Machacek

Seismic explosives are very important tools in the search for oil and gas. Changes and new techniques in seismic exploration methods are also demanding new developments in seismic explosives. This article concentrates on three problems, characteristics of surface seismic explosives,causes of fires in application of surface seismic explosives and new developments in downhole seismic explosives.

Jan 1, 1985

By Charles Dowding, Cathrine Aimone-Martin

This article summarizes an investigation of the structural response of a brick façade home in New Mexico. The subject Ricter residence was located some 1100 to 1400 ft away from an aggregate quarry, and was subjected to a maximum peak particle velocity and air blast over pressure of 0.29 ips and 122 dB, respectively. Superstructure (corner) and mid-wall responses to blasting and human induced activities were measured. An existing exterior crack in the brick work was instrumented to measure crack width response to blasting, human induced activities, and environmentally induced changes in temperature and humidity. Crack and structure response data were correlated with ground velocity and airblast excitations. Amplification of ground motions at the upper structure were calculated and compared with values for typical wood frame structures. The natural frequency and damping characteristics of the structure were determined to compare with measured amplification values. Wall strains produced by bending and inplane tension strains were computed from upper corner structure response and compared to failure strains for drywall and brick veneer. Calculated strains were found to be far lower than those required to crack brick and environmentally induced crack response was found to be far greater than that caused by blast induced ground motion or airblast overpressures

Jan 1, 2005

By Claude Cunningham, Szendrei

The partitioning of blasting energy into “Shock” and “Heave” components is a popular concept for attempting to match explosives to particular ground conditions and blasting results. The issue is complex, as it affects both the detonation process and the immediate response of the rock skin. However, the fundamental process of energy transfer from the explosive to the rock through the blasthole wall is not well defined. Clues to the “Shock” phase of blasthole expansion are given by cratering behaviour of materials subject to high velocity penetrators. The final cavity volume defines both the energy used to achieve this and the resistance of the confining material. Attention is being given to the link between penetration of a solid target and expansion of a readymade hole, both producing the same outcome. The benefit of this work is that it leads to clearer understanding of how explosives will impact upon the blasting results and helps to explain the energy consumption in blasting.

Jan 1, 2004

By Robert C. Brown

During a research period lasting over three years, a vast number of seismograms were collected and analyzed. From this data, other than obtaining a host of new information pertaining to the effects of surface mine blast on underground mines, it was found that by mounting seismograph velocity transducers at the center of crosscuts in underground mines, seismograms can be obtained which give fairly accurate information about the maximum levels of vibration, and the associated Of stresses and strains, misfiring of blast holes, delay accuracy and delay overlap. The technique of analysis is a simple one; it involves matching of the frequency of wave or wave groups with the shot card information such as rows of holes, number of holes and the cumulative milliseconds of delays used in the blast holes. Any discrepancy that might exist between the frequency of waves and the expected cumulative millisecond delay for a given row or hole eventually will show up as a mismatch in the analysis. This simple technique enables the seismographer to be involved not only in the monitoring of blast peak vibration, but also in making recommendations as to the choice of millisecond delays, reducing the possibility of delay overlaps and reducing the hazards of blast hole cutoffs.

Jan 1, 1980

By Ginn Huh

The blasting work to construct a subway in Seoul, Korea have often caused increased neighbor’s complaints because of ground vibration. In order to prevent the damage to the structure, it was necessary to predict the level of blasting induced vibration and to determine the maximum charge weight per delay within an allowable vibration level. The effect of blasting pattern, rock strength and different explosives on the blast-induced ground vibration was studied to determine the maximum charge weight per delay within a given vibration level. The blasting vibration was measured from 10 sites along the subway line in Seoul and an empirical particle velocity equation from over 100 test data was obtained, V=K(D/W1’3 )-” , where the values for n and K are estimated to be 1.7 to 1 S and 48 to 138 respectively.

Jan 1, 2000

The common approach of designing blasts on a trial and error basis is quickly coming to an end. When utilizing the full scale blast environment, trial and error can quickly become cost prohibitive and leaves much to be desired in terms of true blast diagnostics. In these situations testing is usually only continued until a perceived improvement is achieved and when the gross undesirables in blast results are removed. This does does not preclude, however, that further improvements of up to 100% or more can not be obtained.

Jan 1, 1991