Search Documents

By John B. Gayle

The Bureau of Mines has designed and constructed an experimental coke oven, using a commercial oven as a model where practicable. Because the rate of carbonization is important in determining the quality of the coke produced and may affect the "mount of pressure developed during carbonization, particular attention was given to those elements of the design that govern the heat transfer to the charge. The new oven deviates in design from most existing test ovens in that the charge is full width (17 inches), the heating walls ore constructed of 4-1/2-inch silica brick, and zoned, heat-input arrangements compensate for heat losses at the ends, top, and bottom of the charge. This report describes the oven, which was designed by H. S. Auvil and installed under his direction, at the Southern Experiment Station, Tuscaloosa, Ala., while he was supervising, engineer, Coke Section. It gives the results of a limited number of carbonizing tests. These results indicate that the main objective in designing and building this oven, that off duplicating commerical, slot-oven carbonizing conditions, has been accomplished; if coke-discharge conditions simulate commercial-oven conditions, the cokes from the experimental oven arc very similar to oven coke, in soma tests being fully as close is duplicate tests from a Angle batch of coke.

Jan 1, 1952

By Ferdinand Roehlich

An evaluation of the use of manually activated, installed,. dry chemical fire protection systems on underground metal and nonmetal mine vehicles is described. In addition, an assessment of the possible health risks posed by the dry chemical extinguishing agents used in such systems is provided. Work involved installation of fire protection hardware on an operating piece of underground metal/nonmetal mine equipment and, via actual fire tests, a determination of the effectiveness of the hardware in extinguishing on-vehicle fires. Two fire protection systems were installed on a Caterpillar 988 front-end loader in St. Joe Mineral's Fletcher mine, near Viburnum, Mo. Both a fully pressurized Safety First CM-20 and a nonpressurized cartridge actuated Ansul A-101 were installed for comparative purposes. Both systems operated satisfactorily during an 8-month endurance trial period which preceded the actual fire tests. Each system was able to extinguish an 18" x 4" class B test fire placed in the engine area of the machine. The health hazards analysis of dry chemical powder consisted of a detailed search of published literature relating to these multipurpose agents. This data was verified via a controlled laboratory analysis of two monoammonium phosphate based powders (Safety First Unikem and Ansul Forey) and an analysis of air samples collected at various locations on the test vehicle during the fire tests. Although the powder was found to be nontoxic, two potentially dangerous thermal decomposition products were identified--ammonia and phosphoric acid. However, later analysis indicated that an operator would not be exposed to dangerous concentrations of either compound if he were to remain outside of the powder cloud. A "Selection and Use Manual for Manually Activated, Fixed Fire Suppression Systems on Underground Metal and Nonmetal Mining Equipment" was prepared both as an, appendix to the report and for distribution under separate cover.

Jan 1, 1977

By J. J. Forbes

Ventilation is the most important safety factor in the production of coal because on it depends the safety, health, and efficiency of those who work underground. Without adequate and efficient means of supplying fresh air to the working faces, mining could not have advanced as it has. The extent of the workings, the increase in mechanization, and the increasing use of electricity are largely responsible for changes in methods of ventialtion. Ventilation in the early, days of coal mining was accomplished by means of a natural draft, created principally by a difference in the weights of columns of air between the intake and return openings: Later the furnace was introduced for the purpose of increasing the quantity of air in circulation. Mines continued to become larger, their output increased, men were employed in greater numbers, and more fresh coal surfaces were exposed. Coal beds near the surface, and practically free from explosive gas became exhausted, and deeper beds that liberated methane were opened as development advanced. Mechanical ventilation became necessary and was first accomplished by disc-type steam driven fans she old-.fashioned steam driven disc fan has generally been supplanted by the powerful electrically operated centrifugal fans in use at modern coal mines. In order to be secure against gas explosions and provide ample fresh air for persons employed in large coal mines, air must be conducted through the mine to all working places and to all other unsealed parts of the mince in sufficient quantities to dilute and render harmless all dangerous and noxious gases.

Jan 1, 1929

By William J. Douglas

This document describes the development of a conventional mining equipment data base, and an approach for conducting industrial engineering studies of arbitrary mining systems employing network techniques. Data was acquired through underground time studies. Each member of a four-man field team was assigned to a specific machine during each shift for which observations were conducted. Using digital wrist watches and networks describing the man-machine interactions, all events occurring luring the course of each shift were recorded on cassette tapes. The tapes were transcribed, coded, keypunched, and validated using computerized editing techniques. The resulting data files were processed to provide statistics relating to activity durations and event frequencies. The results were used to evaluate operator, machine, and system performance for each section which was observed. Equipment, reliability, and maintainability analyses were conducted using the industrial engineering data files in conjunction with historical information collected at the mine site.

Jan 1, 1976

This report is the first in a "final" series of publications on the Juneau Mining District (JMD). This volume summarizes the results of Bureau of Mines (Bureau) investigations in the JMD during the period 1984-1988. Volume 2 consists of a detailed description of Bureau investigations of mineral de-posits, prospects, and occurrences. Volume 3 is a report on industrial minerals within the district. This study has identified and examined more than 300 mines, prospects, and occurrences containing gold, silver, copper, zinc, lead, nickel, cobalt, tungsten, molybdenum, chromium, and PGM. More than 20 of these were discovered during this study. An additional 20 prospects not mentioned in the literature were rediscovered during the JMD study.

Jan 1, 2012

By James Westfield

A brief résumé follows of some of the most recent activities of the Division of Coal-Mine Inspection that have had a favorable effect. on health, safety, and injuries at coal mines: 1. There were approximately 8,510 active coal mines in the United States during 1955. In all, 82,389 regular Federal inspections of coal mines have been made since Public Law 49 became effective in May 1941; 9,823 of these inspections were made during 1955. 2. The Bureau of Mines introduced the revised Coal-Mine Accident-Prevention Course for Supervisors in the coal-mining industry on March 1, 1948. Since that date, 19,455 supervisors and those aspiring to official positions have completed such training conducted by personnel of the Division of Coal-Mine Inspection.

Jan 1, 1956

By John C. Machisak

THIS INFORMATION CIRCULAR covers the calendar year 1055 and contains statistical data on employment and injuries pertinent to metal and nonmetal mining and to their mills and processing plants that are voluntarily reported annually to the Federal Bureau of Mmes. This report, unlike previous publications, lists not only production and development workers but also office employees associated with mining and milling or processing. The last publication m the series, Information Circular 7798, Injury Experience in the Metal and Nonmetal Industries, 1954, also contains unpublished injury and employment statistics for 1943 through 1953. The Bureau is authorized to request data on injuries and employment from operators in the metal- and nonmetal-mining industries. The information voluntarily submitted by these operators contributes immeasurably to the promotion of safety in the mineral mining industries as it discloses the hazards to which metal and nonmetal workers are continually exposed during mineral extractive operations.

Jan 1, 1959

By Xavier B. Starnes

"SUMMARYThe J. D. Price property is in Crittenden County, Ky., about 5-1/2 miles west of Marion. The Levias-Crittenden Springs fault system traverses the property. Mines on 3 miles of the same fault system immediately northeast have produced about 250,000 tons of fluorspar ore. The Keystone property, adjacent on the northeast, has produced about 150,000 tons of ore. 3/About 1934, lessees, sank a shaft upon the Price property to a depth of 111.5 feet and crosscut from the bottom of the shaft to the principal fault. No ore was found. Later, in 1942-43, they explored the same fault by core-drilling, but this project also was unsuccessful in finding ore.The author visited the property in September 1944, and subsequently the Bureau further explored the property by core-drilling three holes. No ore was found.ACKNOWLEGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. This ex¬ploratory project was under the general supervision of E. D. Gardner, regional engineer of the Central Region, and 0. M. Bishop, district engineer, Bureau of Mines. The mining branch is under the direction of L. B. Moon. The work on the project was under the direct supervision of Xavier B. Starnes, mining engineer."

Jun 1, 1947

By John A. Ruppert

1. It has been proposed that the addition of enough limestone to an open -hearth s lag to give a CaO-3P2O5 ratio of approximately 2-followed by SiO2 firing in an oxidizing atmosphere under the proper conditions of time and temperature will result in a clinker having a magnetic phase containing a preponderance of Mn, Fe, Al, and Mg as oxides and a nonmagnetic phase consisting for the most part of a phosphorus-containing dicalcium silicate. It has been postulated further that the metal oxide phase can be recovered by fine grinding and magnetic separation. These broad principles have been substantiated by numerous clinkering operations made in an electrically fired studio-type kiln, a batch rotary kiln, and a continuous rotary kiln and by magnetic separations made in a Davis -tube separator and a laboratory-size Jeffrey-Steffensen three -roll continuous separator. 2. Quenching the clinker after firing seems to improve its grindability. Microscopic examination of the ground clinker indicates .that the oxide phase grinds down at a somewhat faster rate than the silicate phase. 3. Very fine grinding is necessary to approach liberation, of the oxide phase from the silicate phase. Grinding to ininus-325-mesh, followed by magnetic separation, gave only a rougher concentrate, which had to be reground before final separation. 4. Although the manganese content of the final concentrate was higher, there was some evidence that manganese recovery was lower from a clinker made from a flush s lag than one made from a mixture of tap and flush slags. A possible explanation is that a clinker made from a mixture of slags has a higher iron content and hence is more magnetic and more easily separated.

Jan 1, 1952

By Charles E. Glass

The purpose of this report is to demonstrate the flexibility of rte sensing techniques for providing data with which to implement mined-lands reclamation in an efficient and cost-effective manner. An operational program is presented for using satellite remote sensing data, collateral data, and automated image analysis to provide: 1) an inventory of coal and copper mines and mine waste in Arizona, 2) techniques for periodic monitoring of mining areas using multitemporal classification and image prediction techniques, and 3) delineation of high priority areas for future reclamation and current land-use planning of Arizona mining areas based on environmental hazards indices computed using classified scenes and collateral data.

Jan 1, 1980

By E. M. Frost

"A new apparatus has been devised for quickly and precisely analyzing natural gas for its helium content. The following outstanding advantages make it far superior to any equipment now available for the purpose.3/4/5/6/1. It enables more rapid determinations to be made.2. It has far greater sensitivity than previous apparatus. 3. It is portable.Fifty or more samples may be analyzed in an 8-hour day with the new apparatus and procedure. A maximum of about 10 samples per day could be analyzed with previous apparatus. In the apparatus described, the volume of pure helium obtained from a sample is determined by measuring the pressures created by that pure helium when it is expanded into a constant calibrated volume. In older methods the pure helium separated from a sample is pumped into a burette and measured at atmospheric pressure. The new apparatus and Procedure used with it reduce the average time for an analysis from about 40 minutes to less than 10 minutes,Samples containing a few thousandths of a percent helium may be analyzed as readily as samples containing 1 percent or more, This was not possible with former apparatus. Duplicate samples containing a few thousandths of a percent helium have been analyzed, results checking to one ten-thousandth of a percent. Attempts to measure a corresponding volume of helium in a burette at atmospheric pressure become futile. The ability to determine very small quantities of helium has become of great importance recently in gas- and oil-field engineering studies such Os the utilization of helium as a tracer gas in following the movement of gases through underground structures.A complete apparatus was recently carried more than a thousand miles in a passenger automobile. It arrived without breakage, was .set up and ready to make an analysis in a few hours. .Former apparatus was not portable. The portability of the present apparatus permits taking the apparatus to the field for more efficient prosecution of field engineering problems. The only services required in the field are electricity, tap water, and a source of liquid air or liquid nitrogen.The principle involved is based upon the fact that large volumes of all the constituents usually found in natural gas, except helium, are adsorbed quantitatively on cocoanut charcoal that has been cooled to the temperatures of liquid air. A volume of sample is measured and transferred to a tube of cocoanut charcoal maintained at the temperature of liquid air. After adsorption of all the constituents other than helium, the charcoal tube is connected to a sensitive pressure-measuring device, and the Percentage helium originally in the sample is calculated from two pressure readings and the volume of the original sample."

Jun 1, 1946

By A. T. Coumbe

The first survey 3/ covering sales of liquefied petroleum gases was made in 1930 by the Bureau of Mines, which at the time was under the United States Department of Commerce. This original canvass covered national totals for 1922 through 1929, and most of the supply came from natural gasoline plants. The 1930 report showed approximate totals for butane and propane and for butane-propane mixtures and pentane grouped together. No attempt was made to breakdown the national sales by various uses until 1931, when the quantities for domestic or household consumption, gas manufacturing, and industrial requirements, including miscellaneous uses were indicated. As the market for these liquid petroleum gases expanded and as new uses came into importance, their respective quantities were shown separately in the annual survey. Sales for internal-combustion engine fuel and for raw material for chemical plants were first taken out of the industrial total in 1936. During World War II liquefied petroleum gases became important as feed stock diverted to synthetic rubber plants, and consequently the survey was broadened to cover this particular demand, beginning in 1944. Pentane was dropped from the survey after 1943, as, being liquid at atmospheric pressure, it is not considered as one of the liquefied petroleum gases and furthermore, the quantity reported made up less than 1 percent of the total sales. Thirteen producing companies reported to the Bureau in the first survey made in 1930, and in the 1952 canvass about 130 producers--petroleum refiners and natural gasoline companies--and about 1,300 dealers cooperated by filing schedules showing a breakdown of their sales. Their 1952 deliveries of approximately 4.5 billion gallons of liquefied petroleum gases were equivalent to about 3.4 billion gallons of gasoline or 3.1 billion gallons of distillate fuel oil.

Jan 1, 1954

By Michael W. Redifer

A Fortran IV computer program was developed to calculate the composition at equilibrium of products from a set of high-temperature gas combustion reactions. The program was used to develop high-temperature equilibrium concentration profiles for various constituents as a function of temperature and oxygen concentration. The computer program was specifically applied to reactions pertaining to the corrosion of superheater tubes in pulverized coal-fired boilers; however, it is useful for any multicomponent, multireaction scheme in which equilibrium constant data can be obtained and is comprised of gaseous reactants along with finely dispersed solids or liquids. General applicability of the computer program, including its limitations, are discussed along with detailed instructions for using the program.

Jan 1, 1973

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

APPENDIX E REFUGE CHAMBER LEAKAGE ANALYSIS Variables p 0 = pressure outside of chamber (psi) p = pressure inside of chamber (psi) i q = leakage flow rate (cfm) Q= total leakage (cu ft. ) V = chamber volume (cu. ft. ) t= time (minutes) p= nominal atmospheric reference pressure (14.7 psi) A= chamber leakage coefficient (cfm/psi)

Jan 1, 1976

By T. T. Read, F. C. Houghten

"The bad effects upon the health and output of miners that result when the ventilating current in a mine lacks sufficient cooling power have been described by Harrington and Sayers in a previous report (1)*** The normal temperature of the human body is about 98.5°F. and whenever work is done by the muscles, indeed even when sitting still, the normal bodily processes generate heat which must be given off, otherwise the body will become overheated and a number of bad effects will be produced. If it were possible to so enclose a man that he could continue to breathe and no heat could escape from his body he would die within a short time. In a series of experiments made at the Pittsburgh Station of the Bureau of McConnell and Houghton (2) found that a dry-bulb and a wet-bulb temperature of 112.5°F could he borne for only 35 minutes, even when the subject was at rest. A wet-bulb temperature of 100.4°F (dry-bulb 157°F) could only be tolerated for 45°F minute. Under such conditions the bodily temperature rises as much as 45°F above normal and the pulse is accelerated. Very uncomfortable sensations are felt when the pulse rate exceeds 135. The human body, like any other internal combustion engine, must be cooled in order to function properly.Under ordinary circumstances the air surroundings people is enough coder than themselves to permit this heat generated within the boiy to be river off with¬out difficulty. At higher temperatures, or when the rate of work, with its corresponding generation of heat is high, the body can not throw off heat fast enough, so it begins to sweat and the evaporation of the sweat cools the body. But the results of the experiments cited above indicate that in still air, even with the body at rent, it can not adjust its temperature when the air is above 90° wet- bulb. J. S. Haldane (4) says ""at a wet-bulb temperature of 60°F the actual amount of work done by the miner begins to fall off; as the wet bulb temperature rinse farther the work Bona gradually diminishes to the vanishing point. Then the temperatures indicated by the wet-bulb exceeds 85°F hard work in a mine seems hardly or the commercial working of a mine the wet-bulb thermometer should not in generaI, be allowed to rise above 80°F, unless perhaps where there it a good current."

Dec 1, 1923

By R. T. Sorensen

Research and testing in a small scale equivalent of a commercial flota-tion plant was completed on four low-grade, iron-bearing materials from the western Mesabi range. Closed circuit-flotation of calcium-activated silica with fatty acid collector developed data for comparison with the batch process and highlighted problems not evident from previous bench testing. The four ore samples contained from 27 to 39 percent Fe and were equally represented by nonmagnetic taconite and semitaconite type materials. Iron concentrates containing 6.0 percent, or less, SiO2 were made 5, all four samples. Of the two material types, the semitaconite was the ore amenable to treatment, yielding iron recoveries of about 90 percent as cc pared with 70 to 80 percent for the other. Pilot plant tests showed that concentrate grade made in batch tests could be duplicated in the closed circuit and demonstrated that the amount of recoverable middling iron varied considerably between ore samples. The continuous tests also showed that water temperature strongly influenced results in the treatment of one ore but apparently was of indifferent consequence in another. Progress in thickening and filtration of flotation concentrates was made through introduction of tapioca flour to serve the dual role of iron mineral depressant and flocculant.

Jan 1, 1966

By K. K. Kelley

The first bulletin (245)3 in this series, which appeared in 1932, summarized the entropy values then available for the elements and inorganic compounds, results being listed for some 150 substances. In the interim advances in the realms of spectroscopy applicable to the determination of thermodynamic properties and in the development of methods of calculation therefrom have added many highly accurate values. Moreover, through the efforts of Prof. W. M. Latimer (286) and his coworkers, satisfactory entropy values are now available for all but a few of the common inorganic ions in aqueous solution. At the same time rapid progress has continued in the study of low-temperature heat capacities in several laboratories, In addition, compilation and correlation of data pertaining to vapor pressures (247), thermodynamic properties of carbonates (258), thermodynamic properties of sulfur and its inorganic compounds (250), and the thermodynamic properties of metal carbides and nitrides (251), which were published as members of this series, have yielded many values. As a result, over 500 usable entropy values for inorganic substances may now be tabulated. This bulletin originally was planned as a second revision of the first member of this series, the first revision (249) having appeared in 1936; however, because of requests for the explanatory section of the first bulletin from those teaching thermodynamics, it was decided to com¬bine the information in the first bulletin and its revision with the data that have appeared since 1935 and to repeat the explanatory material in somewhat more detail. The purpose of this bulletin is therefore to give the available values of the entropies at 298.1° K. of the elements and inorganic compounds, together with enough explanation of the methods employed in calculating entropies to make the results comprehensible.

Jan 1, 1941

By Eugene Frey

"INTRODUCTION The Blue Bell fluorite deposits were examined in August and November 1944 by an engineer 3/ of the Bureau of Mines, and an underground project was set up. The Bureau of Mines began development of fluorite here February 10, 1945, and completed its survey on June 21, 1946.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepared the final report. The Metallurgical Branch, C. C. Ralston, chief, analyzes samples and perform beneficiaticn tests. The exploratory project was under the direction of Paul T. Allsman, chief, Salt Lake City Division, Mining Branch. Acknow¬ledgment is due R. Thurston of the Federal Geological Survey for mapping the topography of the area, and to F. H. Gunnell and W. A. Young of the divisional office for detailed mapping of the surface and underground development and interpretation of the results.The chemical analyses included in this report was performed under the direction of H. E. Peterson, analytical chemist; the petrographic studies on the ore were written by LaMar Evans, petrographer; and the beneficiaticn section was written by C. H. Schack, metallurgist, under the direction of S. R. Zimmerley, chief, Salt Lake City Division, Metallurgical Branch."

Jul 1, 1947

This summary of State laws on explosives was compiled primarily to ascertain what subjects relating to their control have been acted upon by each State legislature and, in general, how they have been treated. It does not include any legislation passed after 1942, or any proclamations, regulations, or administrative orders. It does not purport or attempt to be authoritative. If any problem arises involving interpretation of the statutes of any particular State, the original source must be consulted for the exact words used by the legislature. This summary, however, will be useful in determining whether relevant statutes exist, and in locating them quickly with a minimum of effort. It will be of value also in comparing statutes in one State with similar statutes in other States to determine what construction has been placed upon them by the courts of these jurisdictions or to contrast the varying provisions of many States upon a similar subject. To make these comparisons easier, the statutory provisions for each State have been grouped under several major topics in outline form. Although this sometimes has resulted in disruption of the continuity of individual acts, the increased general clarity and availability of comparable sections have more than justified the procedure followed.

Jan 1, 1943

By K. B. Bengtson

This task report provides the process technology, preliminary design, capital and operating costs for a 25 TPD pilot plant to produce cell-grade alumina using a clay/hydrochloric acid extraction - HCI gas induced crystallization process. The report consists of six volumes: I - Process Technology and Costs; II and III - Equipment Lists, Specifications and Quotations; IV and V - General Specifications; VI - Drawings. The process was selected by the Bureau of Mines as the more promising method to produce cell-grade alumina from clay based on the results of the two previous task reports under this contract: Task I - Comparison of Six Processes (alunite, anorthosite-lime sinter, clay/sulfurous acid, clay/nitric acid, clay/hydrochloric acid evaporative and gas-induced crystallization) and Task 2 - Comparison of Two Processes (clay/nitric acid and clay/hydrochloric acid - gas induced (crystallization). The pilot plant process utilizes a unique dual crystallization process to produce aluminum-chloride-hexahydrate crystals having sufficient purity when decomposed to meet stringent alumina product specifications. The size of the 25 TPD pilot plant has been selected to permit scale-up to commercial size plants of equipment, technical and economic parameters. The capital cost estimate for the pilot plant, exclusive of fee and escalation, for a southeastern U.S. location is $52,311,000 expressed in 1979 dollars. The total time required to construct the pilot plant including engineering and procurement is 32 months. The operating cost to produce the estimated 9,000 tons of alumina required for testing in Hall cells is $40,91[0],190 expressed in 1979 dollars.

Jan 1, 1979