Search Documents

By K. L. Williams

The Bureau of Mines laboratory tested the response of a commercially available real-time aerosol monitor (GCA RAM-1) to various dusts. Monitor measurements were recorded, averaged, and compared with simultaneous gravimtric measurements of each test dust. Tests usually lasted several hours. The test dusts of various particle size distributions used included coal, limestone, and a commercially available test dust. For each particular dust, the monitor response was linear and correlated well with mass concentration over the range of about 0.5 to 10 mg/m3. The monitor can estimate a 2.0-/m3 respirable coal dust concentration within as little as 26 pct with 95 pct confidence. The monitor must, however, be calibrated with the dust to be measured because the instrument response is affected by the type of dust particle. The average monitor response to same mass concentration of coal dust was approximately twice the average monitor response to the same mass concentration of limestone dust.

Jan 1, 1984

By L. A. Haas

S02 reduction with CO was studied in an integral flow reactor at a nominal flow of 0.5 liter per minute. Reactant gas contained 3 percent SO2, 6 percent CO, and the balance He. SO2 conversion was determined for three different types of catalysts. The first consisted of 16 commercial catalysts used for various chemical syntheses. Only the commercial catalysts which contained transition metals in alumina removed more than 30 percent 80a at temperatures below 510° C. Two other types of catalysts were prepared in the laboratory either by pelletizing equal amounts of powdered alumina and transition metal oxides or by impregnating commercial alumina tablets with transition metal ions. Regardless of preparation techniques, Cr and Fe in alumina were the two best catalysts. The observed results suggest that an intermediate (SCO) is formed by the interaction of surface metal sulfides and carbonyls. Alumina then catalyzes the interaction of SCO with S02 to form the end products (sulfur and carbon dioxide). Over 80 percent S02 was removed at 460° C with 2 grams alumina impregnated with 2.5 percent iron.

Jan 1, 1972

By L. H. Adami

This paper reports the results of solution calorimetry conducted to obtain the heats of formation of crystalline FeS04?6.952H20 and FeS04?1.008H20, from. which values were derived for the stoichiometric compounds FeS04?H20 and FeS04?H20. Also included are derived values of the free energies of formation and dehydration. This work was undertaken primarily to fill a need for data for pure, easily obtainable ferrous compounds that are suitable for use as calorimetric intermediates, The ferrous sulfate hydrates meet the essential requirements for this use.

Jan 1, 1963

To improve efficiency in producing clarified water from mineral and metallurgical processing streams containing suspended particles. Approach Particles suspended in mineral and metallurgical processing streams are filtered out by granular magnesium oxide (MgO) used as the medium in deep bed filters. How It Works MgO is substituted for the silica sand or garnet sand currently used in conventional deep bed filters. These filters presently consist of a 24- to-48-inch-deep layer of either silica sand or mixed media, consisting of a stratified combination of anthracite coal, silica sand, and garnet sand. As waste water containing fine solids is percolated through the granular bed, the suspended particles become attached to the filter grains. When MgO replaces sand as a filter medium, the overall filter capacity is generally increased 50 to 80 percent, and no equipment modifications are necessary for filter operation. MgO is unique because it has a positive surface charge in water while most suspended materials are negative. The attraction of these negatively charged suspended particles to MgO enhances filtering performance. As is necessary for all good media, MgO is insoluble and nontoxic.

Jan 1, 1983

By Robert C. Ellman

The Bureau of Mines investigated the factors that cause agglomeration of lignite by freezing during winter shipment and sought methods to avoid it. Tests showed that lignite may be freezeproofed by removal of the relatively small quantity of moisture involved in forming the frost crystals which cement particles together, or by controlling the crystal characteristics. Adding dried lignite fines proved to be an effective and superior freezeproofing method. Commercial adoption of this method has been successful.

Jan 1, 1965

By C. H. Gorski

Evaluation of raw materials for mineral wool is one phase of the Bureau of Mines broad program for the more effective utilization: of our mineral resources. The experimental work and test-evaluation results on several raw materials as useful components for the production of mineral wool are presented in this report. Samples from all sections of the United States, including copper slag from Tacoma, Wash., pebble phosphate slime from Florida, and granites from Massachusetts and Minnesota, have been blown into mineral wool successfully in the laboratory tests. Maximum conservation of the Nation's mineral and manpower resources requires maximum utility of those resources. Al though the domestic reserves of oil, gas, and coal are tremendous, judicious use of these fuels through the use of proper insulation will insure the highest thermal efficiency. The effectiveness of mineral wool as a heat-insulating material has assumed an increasingly important role in the national economy, and it has become a fuel saver in countless applications. The most immediate concern to many is the use of mineral wool in the home, which promotes uniform temperature and minimizes drafts by reducing heat transfer through the walls, ceiling, and floors. There are, however, many industrial and commercial uses that require large volumes of mineral wool each year.

Jan 1, 1951

By C. W. Sill

[In the original Norris and Fay method for determining selenium, selenious acid is reduced by an excess of standard thicsulfate in accordance with the following reaction: H2Se03 + 4Na2S203 + 4HC1 = Na2SeS406 + Na2S406 + 4NaC1 + X20. (1) The excess thiosutfate is then back-titrated with standard iodine solution. The disadvantages of ouch a method are obvious. On an unknown sample, the quantity of thiosutfate required would be difficult to determine; a definite excess is required, but large back titrations would be undesirable. Inasmuch as thiosulfate is decomposed by acid, considerable error may be introduced in this method, the amount depending on the acidity, temperature, concentration of excess thiosulfate, duration of contact between thiosulfate and acid, and other factors, In a critical study of the Norris and Fay method, Coleman and McCrosky3/ show that the method is accurate to less than .1 part per thousand if the excess of this sulfate Is not greater than 5 ml. of 0.1 N solution (in 1.0 ml. of 0.x4 N sulfuric acid) whether the titration is made at 0° or 20°C. A greater excess produced unsatisfactory values at either temperature. Coleman and McCrosky regulated the excess thiosulfate by adding 5-ml. portions of thiosulfate solution followed by the addition of 1 to 3 drops of 2.5 percent potassium iodide in the presence of starch. If a starch-iodine blue color formed locally around the drops of potassium Iodide, the reduction of selenious acid was not complete. On stirring the solution, the local blue color fades and another 5-ml. portion of thiosulfate is added. When addition of potassium iodide fails to produce a local blue color, reduction of selenious acid is complete, and the excess thiosulfate is then back-titrated with standard Iodine solution. The number of equivalents involved in the reduction of selenious acid by either thiosulfate or iodide is the same, and therefore no correction need be made for the potassium iodide. This procedure is much better than the original Norris-Fay titration, but acidity and time would stilt be rather critical factors subject to variation with individual technique. Also, the method still requires the lose of two standard solutions, a rather undesirable factor from the standpoint of routine application.]

Jan 1, 1954

By William W. Adams

The stone-quarrying industry of the United States, including such related operations as rock crushing, rock dressing, and the manufacture of cement and lime, reported a larger volume of employment in 1934 than in 1933. Reports from the operating companies to the United States Bureau of Mines showed an increase in the number of men employed, number of man-days of employment, and total number of man-hours of labor performed during the year. Moreover, the average worker had a longer period of employment during 1934, the gain amounting to 11 percent over 1933. The increase in employment was accompanied by no increase in accidents for the industry as a whole; in fact, the accident rate for 1934 was a fraction lower than the rate for 1933. In some branches of the industry the frequency of accidents increased, but these increases were more than offset by reductions in rates for other branches. Reports for 1934 were received from 1,403 active plants. The working force averaged 64,331 men for 204 days per man, and the total period of employment for all of the men was 95,258,880 man-hours. Each employee averaged 1,481 hours of work during the year. The total number of hours of labor represented a gain of more than 8 percent, and the average working time per employee showed a gain of 62 hours per man.

Jan 1, 1936

By Benjamin W. Haynes

Analytical procedures are described for the quantitative determination of 16 elements (As, Ba, Be, Cd, Co, Cr, Cu, Fe, Mn, Mo, Ni, Pb, Sb, Se, TI, and Zn) and 7 ionic species (NH4, C032-, CI-, F-, NO3-, P043-, SO42-), identification of major and minor mineral components, and measurement of physical properties associated with manganese nodules and nodule processing reject waste materials. Compound identification methods discussed include X-ray diffraction, infrared spectroscopy, scanning and transmission electron microscopy, selective area electron diffraction, and optical and reflected light microscopy. Methods for elemental analysis include atomic absorption spectrophotometry, inductively coupled plasma emission spectroscopy, neutron activation analysis, fluorescent X-ray spectrography, and ion chromatography. Thermal gravimetric analysis, ultraviolet-visible spectrophotometry, ion specific electrodes, and standard wet chemical procedures are briefly discussed. Physical properties determined in manganese nodule materials include grain size distribution, specific gravity, triaxial shear, permeability, maximum density, Atterberg limits, and slurry density. The results of a round-robin analysis of an ammonia process waste material and manganese nodule standards demonstrate the applicability of the discussed methods. Tests discussed for the evaluation of the waste materials for disposal options include the Environmental Protection Agency (EPA) EP toxicity test, the ASTM shake extraction test, and the U.S. Army Corps of Engineers EPA seawater elutriant test.

Jan 1, 1983

By Arnold B. Hubbard

This report describes a method of concentrating the insoluble organic material (kerogen) in a rich Colorado oil shale without any apparent alteration of its original chemical form. The method involved treating finely pulverized shale with dilute acetic acid at room temperature to remove the carbonates, which act as a cementing agent for the shale, and cause the shale particles to partly disintegrate into the organic and inorganic components. The acid-treated shale then was centrifuged in different liquid mediums ranging from 1.4 to 1.15 gravity to effect a mechanical separation. From a Colorado oil shale containing 48.0 percent ash, kerogen concentrates containing 43.3 to 8.7 percent ash were obtained. The carbon:hydrogen ratios of the kerogen in the original shale and the different concentrates were essentially the same. The oil:kerogen ratios calculated from Fischer assays of the above samples were essentially the same, regardless of the organic or inorganic contents. This was also true of the assay water:kerogen ratios of the same samples. These data indicate that no significant change occurred in the kerogen during the concentration process.

Jan 1, 1952

By B. Dimitriades

Exploration of the photochemical reactivity of diesel-exhaust hydro-carbons is described. A smog chamber was built, and reactivities of diesel exhaust, gasoline exhaust, and propylene were measured at two chamber temperatures. Experimental data indicated the problems caused by instability of diesel-exhaust hydrocarbons. With reservations due to these problems, the results are interpreted to reflect comparable reactivities for diesel and gasoline exhaust.

Jan 1, 1971

By H. R. Shell

Of three known compounds in the ternary system K20 - PbO - SiO2, one having the composition K2Pb4Si8021 crystallizes into a structure with asbestiform properties. This compound, whose silicon-oxygen ratio is between that of the layer silicates (for example, mica) and the double-chain amphiboles, crystallizes in the tetragonal system. It malts, apparently congruently, at 779° C. The fiberized product prepared from crystals is fluffy and closely resembles natural asbestos in appearance, but is more brittle and has less strength. However, potassium-lead silicate may be separated into fibers with a uniform diameter of 200-300 A.U., and the fibers show with the electron microscope the s criteria that have been interpreted as indicating a hollow tube structure in chrysotile asbestos. Since very few inorganic crystalline compounds have such a structure, the material has unusual scientific interest. Microcrystalline potassium-lead silicate was rapidly and completely formed when powdered glass of the same composition was heated to 650° - 700° C, but macrocrystals grew only slowly from the viscous massive glass. Maximum growth rate was 0.12mm. per hour at 700° C.

Jan 1, 1957

By Mark Sanders

The report describes three experiments that were conducted to determine the effects of size and weight of the miner's battery pack on performance in the low seam coal environment. Three separate experiments were carried out in a simulated low seam coal mine. The first experiment tested the sensitivity of task measures (i.e., subjects performed locomotion) shoveling, cart pushing, and timbering tasks) to detect variations in the size and weight of the battery pack. The results of the first experiment demonstrated that only the locomotion tasks were sensitive to size and weight variations. The second experiment, therefore, focused on the locomotion tasks and tested the effects of varying size and weight on task completion time. The third experiment was designed to compare the present battery pack to a radically different configuration of power cells. The most important findings were that changes in weight affected locomotion times but changes in size and configuration had small and inconsistent effects. Opinion data of subjects indicated a strong preference for a battery nark belt concept.

Jan 1, 1980

By D. S. Burgess

A commercially available Halon 1301 extinguisher has been evaluated as part of an explosion-suppression system for use in coal mines. Studies were made both of the dispersion pattern of the Halon 1301 at an initial pressure of 280 psig, and of the efficacy of this suppressant against 9.5 percent methane-air flames. These flames were quenched successfully only when the suppressant was applied before the fireball diameter exceeded 18 inches.

Jan 1, 1971

By P. R. Jones

A computer program was written for the design of a shell and tube heat exchanger on a price optimum basis for the following conditions: (1) Triangular pitch; (2) single or multiple pass; (3) heating or cooling; (4) no change in phase; and (5) inside pumping costs immaterial. Price optimum design was obtained for four standard tube sizes and standard pitch. The inside pressure drop was fixed and outside pressure drop was computed for the optimum baffle spacing and when the baffle spacing equaled the shell diameter. Standard shells whose areas equaled or exceeded the required area were also listed. The program was made adaptable to various fluids and to various tube sizes and pitch by reading in many of the required data such as physical properties of the fluids, tube data, and standard shell data in tabular form.

Jan 1, 1968

By Lowell Stroud

A windowed-cell phase equilibrium apparatus was used to obtain equilibrium vapor- liquid data for a helium-bearing natural gas (Hogback) at temperatures from -100 to -250° F and pressures to 500 psia. Anomalous phase behavior resulting in the formation of two stable liquid phases occurred at tmperatures below -200° F and pressures above 200 psia. A review of the published literature on the occurrence of multiple-liquid phases included in the report indicates that the experimental results with Hogback gas are the first substantiated evidence of a vapor-liquid-liquid equilibria in a helium-containing natural gas.

Jan 1, 1963

By W. D. Mcmillan

During the fall of 1943 the Bureau of Mines put down four churn-drill holes totaling 435 feet of bore at the McGregor zinc lead mine near Potosi, Washington County, Mo., after the property had been examined by John Soule, an engineer of the Bureau, in the fall of 1942. A small production of lead and barite ore had been maintained at this property for many Years from shallow deposits in residual clays. A few shafts had penetrated the underlying dolomites and exposed a network of narrow fractures containing galena, sphalerite, barite, and marcasite. The drilling by the Bureau tested conditions at depths ranging from 80 to 130 feet. This report sets forth the data resulting from the work.

Jan 1, 1948

By Frank D. Lamb, Lloyg H. Baning

"The crushed-stone industry has long been troubled with the problem of producing a more or less cubical product for use as concrete aggregate. Its seriousness varies widely for each producer, depending upon the character of the rock employed for raw material and the ultimate use of the crushed stone. For many construction uses, such as the macadam or bituminous-concrete- type road, flat pieces are not objectionable and may even be preferable to more cubical rock. However, most specifications for concrete require that the stone must be reasonably free from flat and elongated pieces.The rigid specifications set by many contractors have resulted in the rejection of coarse aggregate that, except for the presence of an excessive amount of flat and elongated pieces, would be entirely acceptable. In many instances, if an efficient, economical method of removing flat and elongated pieces were available, local producers could meet the requirements of the contractor and thus eliminate the necessity for importing more cubical material.A brief investigation of the problem of removal of flat and elongated pieces from crushed aggregate, carried out at the Eastern Experiment Station of the Bureau of Mines, indicated that it is mechanically possible to remove flat pieces from crushed rock.TEST EQUIPMENTA number of mechanical devices are used by the coal industry for separating slate from coal; these depend upon the difference in shape of the crushed slate as compared with the coal. Such devices as shutter screens, spiral separators, and the Norman picker would be suitable for removing flat pieces from crushed rock in the same manner as they are used by the coal industry. None of these devices was immediately available for testing purposes, so an attempt was made to construct a simple device that could be used in commercial operations."

Sep 1, 1944

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining I research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and, the results are described in this report.

Jan 1, 1983

By R. V. Higgins

In a recent report3/ the authors presented a rapid method of calculating, by means of a desk calculator, the future performance of oil reservoirs in which the motivating agent was gas. The accuracy of the method was tested by data obtained from an electronic computer. Because of the accuracy obtained for the limited number of calculations performed, considerable interest has been expressed in the electronic computer program used to obtain the comparative data by an analytical solution. Accordingly, the computer procedures for the analytical solution are presented in this report. In an earlier report, 4/ a reservoir appraisal procedure was published in which an iterative method was used. Many requests were received for the computer program used to obtain the values given in that paper. That program, with some modifications, also is presented in this report. The modifications are given because of the progress that his been made in computers, and because much of the program for the analytical solution is usable for the iterative procedure.

Jan 1, 1960