Search Documents

By Fred D. Wright

Some new equipment for drilling vertical holes, cleaning blast holes, hauling explosives, and conditioning Diesel exhaust gas has been developed. at the Bureau's Experimental Oil-Shale mine near Rifle, Colo, The equipment has application, not only in oil-shale mining, but in many of the country's underground mines in which room-and-pillar methods of mining are employed. This report presents the Bureau's experience in testing the following equipment in the Experimental Oil-Shale mine: 1. A four-drill benching jumbo for drilling 23-foot vertical blast holes 2. A jet borehole blower for efficient cleaning of deep, vertical blast holes. 3. An explosives truck equipped with two compartments to provide safe conveyance for dynamite and detonators. 4. A mobile, electric substation to provide switching equipment, low-voltage and overload protection, and transformer facilities to remote locations in the mine. 5. A chemical conditioner for scrubbing the exhaust gases from Diesel-powered equipment used in underground operations. 6. Other units of equipment which have been tested at the Experimental mine.

Jan 1, 1951

By Joseph J. Wallace

The 1952 Annual Report of the West Virginia Department of Mines lists seven beds that are being mined in Mingo County, of which the Cedar Grove is the most important. The Cedar Grove, Alma, and Coalburg contain the largest remaining known reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, are estimated at 3,007 million short tons as of January 1, 1953. Of this total, 2,396 million short tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1954

By Paul W. Jeran

This Bureau of Mines report has been prepared to provide a means whereby mineworkers without specific geologic training can recognize and record the existence of potentially hazardous geologic features encountered in coal mines. Each geologic feature described in this report has been implicated in roof failure. Through the recording of the observations of mineworkers, based on this report, a geologic map of mine workings and the associated ground control problems can be compiled. From such maps, the trends of changes and features can be determined and projected ahead of mining. The face crew can be alerted to a potential problem and what to look for as the face is advanced.

Jan 1, 1983

By N. E. Hanna

An important goal in the development of coal mining explosives has been to improve their safety characteristics through suitable formulation. In the United States no systematic effort to establish factors influencing the incendivity to firedamp and to coal dust of explosives through research was made until the last decade. In consequence, American permissible explosives underwent only very slight modifications and many remained substantially the same as in the early years. As part of a long range program for increasing the safety of permissible explosives, the Bureau of Mines undertook to determine how the amounts and particle sizes of the principal constituents of these explosives affect their incendivity. It was found that an increase in the relative amount of sodium chloride and a decrease in its particle size significantly decreased the incendivity of our permissible explosives to firedamp (7-9).6 This is in agreement with findings reported by Dolan (4) for compositions of nitroglycerin and salt. One important result of the work at the Bruceton station has been the recent introduction of salt-formulated permissibles by several explosives manufacturers. This paper describes a statistically designed experiment for studying the effects of the particle size of ammonium nitrate and the type of carbonaceous materials used on the incendivity of permissible explosives. Interest in these particular effects goes back as far as the first formulations of coal mine explosives, around 1910 in the United States and even earlier in Great Britain and other countries. Although it is well established that fine

Jan 1, 1961

By CHARLES L. WRIGHT

Previous work.-The general plan of work outlined for the Government fuel-testing plant erected at the Louisiana Purchase Exposition, at St. Louis, Mo., in 1904, included investigations relative to the briquetting of coals found in the United States. These investigations embraced the possibility of making satisfactory commercial fuels from lignite or low-grade coals which do not stand shipment well; of benefiting culm or slack coals that are wasted or sold at unremunerative prices; and of improving the furnace efficiency or ability to withstand transportation of good coals. This work was begun in 1904 and was continued in 1905, 1906, and 1907 as an essential part of investigations looking to the determination of methods for reducing waste and increasing efficiency in the utilization of the fuel resources in the United States. The initial briquetting tests at St. Louis, which included examination into the behavior of different coals or mixtures of coals in the briquetting press, experimental study of the merits of various substances used as binders, and consideration of the physical properties and resistance to weather and abrasion of the briquets, have been described.a They demonstrated that satisfactory briquets could be made from most coals, and that by briquetting the commercial value of many low-grade coals and lignites could be raised enough to more than cover the cost of manufacture. Norfolk plant.-The briquetting plant of the Geological Survey was moved from St. Louis, Mo., to Norfolk, Va., in 1907, along with the steam boiler and producer-gas equipment of the fuel-testing plant, as the closing out of the affairs of the Louisiana Purchase Exposition and the consequent removal of the buildings from Forest Park made a change of location necessary. Norfolk was selected largely with a view to the testing of coals for naval purposes, and because of facilities in the way of buildings and materials offered by the Jamestown Exposition Company. The work at Norfolk was chiefly devoted to making steaming and briquet tests of coals which reach the Atlantic seaboard at Norfolk and Newport News and are used by the navy and merchant marine. Two briquet machines were installed at the Norfolk plant, one being the English machine used in briquetting tests by the Geological Survey at St. Louis in 1905 and 1906, and the other an American machine. The briquets made at this plant were tested on locomotives of several railroads entering Norfolk and on the United States torpedo boat Buldle in comparison with the run-of-mine coal used in making them. Some of the tests were conducted by the railroads on their own locomotives, but those on the Biddle and on the locomotive of the Seaboard Air Line Railway were carried on by W. T. Ray and Henry Kreisinger, of the United States Geological Survey. Personnel.-Charles T. Malcolmson continued in general charge of the briquetting section after the removal to Norfolk until January 1, 1908. Walter J. Chapman continued in charge of operation of the briquet machines and of the observations reported under the heading "Details of manufacture." Charles L. Wright supervised the installation of the English briquet machine and later in the year continued the physical tests of briquets and the analyses in the chemical laboratory of the section until January 1, 1908, on which date he was placed in general charge of the work of the section. G. E. Ryder and Ralph Galt also continued with the staff, but the former was obliged to resign soon after the plant was in operation on account of ill health; the latter continued with the section as computer until the close of work on December 1, 1908.

Jan 1, 1911

By Richard G. Geyer

One aspect of a program to improve the chances of survival following coal mine disasters is the development of a communications sys tem which will allow surviving miners to make their circumstances known to rescue teams. At present, it appears that an electromagnetic system may be most practical. The development and design of an effective electromagnetic communications link for signalling between mine workings and the surface requires knowledge of pertinent physical properties of the rocks overlying the mine workings and the characteristics of the ambient noise against which a communications signal must be recognized. Knowledge of the overburden electrical transmission properties is useful not only for determining a practical operating transmitter frequency at a given mine, but also for ensuring the best possible electromagnetic coupling for routine or emergency communication purposes. Field studies of the electrical transmission properties of the overburden of coal mines in Colorado, Illinois, and Pennsylvania generally show that a relatively uniform and unimodal electrical conductivity distribution exists provided that the region has not been subject to considerable structural or metamorphic deformation such as that observed in the Gary District of West Virginia. Measurement s of ambient surf ace electromagnetic noise levels at several mines in Colorado, Illinois, and West Virginia were taken and analyzed and are presented in the form of amplitude histogram plots both as a function of frequency and time of day. These amplitude histograms may be used in conjunction with overburden resistivity data in implementing an uplink communications beacon system which will yield a specified signal- to-noise ratio at the surf ace. Numerous C .W. field transmission tests were made in various coal mining environments with use made of either a buried vertical-axis transmitting loop or a short insulated grounded current line. These transmission tests were made from 20 Hz to 20,000 Hz in frequency and at several geographic surface receiving sites. The results of these field measurements show, in general, good agreement with theoretically calculated results. Since the produced surf ace magnetic field from a buried vertical-axis loop source or the produced surface horizontal electric field from a buried horizontal current line show better agreement with theoretical results, they could be used for beacon location system. One criterion would be in detecting the equatorial and polar null lines of the horizontal electric field component which is normal to the direction of emplacement of a buried transmitting line current source. A second criterion would be in the surface mapping of the maximum in the vertical magnetic field directly over a vertical-axis loop transmitter and the associated null is the vertical magnetic field at a horizontal offset distance which is about 1.4 times the depth of burial of the transmitter. Finally, a third criterion would lie in the surface mapping of the null in the horizontal magnetic field directly over the vertical-axis beacon and the associated maximum in the horizontal magnetic field at an offset distance from the transmitter axis of half the depth of burial of the loop transmitter. In mapping the vertical magnetic field over a buried vertical-axis loop transmitter, the size effect of the transmitter loop must be taken Into account when the separation distances between the transmitter and receiving sensor are less than ten times the effective radius of the source loop; increasing the size of the transmitting source relative to the source-receiver separation distance shifts the null in the vertical magnetic field to greater offsets. In mapping either the vertical or horizontal magnetic field over a buried vertical-axis loop transmitter, care should be exercised in ascertaining that measured nulls and maxima are along radials through the axis of the buried source loop. For the main part, coupling experiments show that ambient electromagnetic noise in coal mining districts is less of a problem above 1000 Hertz. But secondary and perhaps undesirable maxima and null phenomena (as well as penetration problems) would occur in many coal mine provinces in the behavior of the surface horizontal magnetic field (over a buried vertical-axis loop transmitter) if transmission frequencies as high as 10 kHertz were used.

Jan 1, 1974

By E. P. Youngman

Before the World War the use of zirconium and its compounds was largely experimental and confined almost wholly to Germany and Austria . Occasionally small lots of zirconium ore had been produced in the United States ( 1,000 pounds in 1869 , 26 tons in 1883 , and 3,000 pounds in 1903 ) and used (with monazite ) in the manufacture of various lighting devices , especially incandescent gas mantles ; but it was not until 1906 that the discovery of the natural zirconium oxide in large quantities near Sao Paulo , Brazil , first gave promise that a zirconium industry eventually might be developed . Edward Rietz , who worked the Brazilian deposits , interested German chemists in extending the use of zirconium , and by 1911 trade journals were listing German firms as manufacturers of compounds or products derived therefrom . For a time zirconia was one of the various oxides used in the Nernst lamp . It was used also for crucibles and hearths as refractory material ; in the manufacture of chemical utensils ; in enamels ; in the place of bismuth subnitrate for defining Röntgenray pictures of the stomach ; as a pigment ; in medicine ; and in a number of other ways . The Germans were credited also with producing a remarkable zirconium steel , which , it was claimed , was much superior to other alloy steels . During the World War the United States Government investigated the possibilities of zirconium , as well as those of other steel -hardening elements , and a large automobile manufacturer actually purchased a substantial quantity of ore with the purpose of employing zirconium in automobile steels . Immediately after the armistice the Government ceased its investigations ; but despite the difficulties experienced by various investigators in reaching concordant results , interest in the use of zirconium as a steel -hardening agent , as well as in other uses of the element and its compounds , continued . In 1918 the Foote Mineral Co. , which had been interested in zirconium for several years , was exploiting the deposit in Brazil formerly worked by the Germans and was supplying zirconia in the form of ore , brick , and cement for refractory and other purposes . About the same time the Electro Metallurgical Co. , which before the entrance of the United States into the war was experimenting with zirconium alloys , supplied in tonnage quantities the demand for these alloys . In 1919 it was reported that American manufacturers , after several years of research, were producing in commercial quantities pure zirconium oxide , which was finding a place in the manufacture of small refractory articles , scorifying dishes , crucibles , tubes , and one- piece furnace linings . In 1920 the lowering of the price of zirconium metal powder ( because of improved metallurgical methods ) promised the production of the metal on a semicommercial scale . In 1924 the Titanium Alloy Manufacturing Co. introduced a new opacifying agent , " Opax , " made from zircon . A year or two later some of the large pottery manufacturers became interested in the use of zirconium oxide as an opacifying agent , the increased production of titanium pigments having resulted in the production of zirconium as a by-product at a price that could compete with tin oxide . In 1928 it was reported that the industrial use of zirconium oxide was increasing steadily in the manufacture of brick , crucibles , and other refractory products , such as high- temperature cements . However , the reluctance of producers to install additional and more suitable

Jun 1, 1931

By R. H. King

A very simple cold-bend test was devised and tested for evaluating thermoplastic jackets used on mine-power-feeder cables. A test sample is bent into a semi-circle whose radius is equal to the minimum bend radius recommended by IPCEA and then cooled to the, desired test temperature (-35°C). While at temperature, the sample is straightened by pulling the cable ends with a winch arrangement. The results show that of the jackets tested, those which cannot withstand the test literally burst when the sample is straightened.

Jan 1, 1978

By John C. Edwards

Several experimental programs were conducted at the Pittsburgh Research Center to investigate the level of mine fire detection and alarm capability possible using state-of-the-art technology. These programs involved comparison of the response and alarm time of optical and ionization type smoke sensors to smoldering and flaming coal combustion in a smoke chamber. Coal combustion experiments conducted in the smoke chamber demonstrated that a CO concentration of 5 ppm above ambient corresponded to an optical density of 0.022m1. For the four smoke sensors for which a continuous analog signal was available, a smoke sensor alarm was defined as the average background signal plus ten times the peak-to-peak noise. This alarm criterion resulted in the association of the alarm for three of the four sensors with a smoke optical density of 0.022m-1. and 0.033m-1 for the fourth smoke sensor. The smoke sensors used in the smoke chamber studies were incorporated into large scale diesel fuel fire experiments conducted under normal ventilation conditions in the Safety Research Coal Mine (SRCM) at the Pittsburgh Research Center. These experiments showed that a diffusion mode smoke sensor alarmed earlier than a diffusion mode CO sensor; and, based upon the measurement of the optical transmission at the location of a pump mode ionization type smoke sensor that a pump mode ionization smoke sensor alarmed at an average smoke optical density of 0.021m" for the twelve experiments conducted. A series of 30 and 330 kW diesel fuel fire intensity experiments were conducted under zero airflow conditions in the SRCM. It was determined that :(I) thermal sensors are inadequate at 30 m from a 300 kW fire;(2) a diffusion mode ionization smoke sensor can be more effective for mine fire detection than a diffusion mode CO sensor;(3) recommendations can be made for sensor spacing in a mine entry based upon the measured CO buoyancy induced spread rates along the mine roof and the time for a developing coal fire to ignite a conveyor belt.

By R. H. Schutz

TO ASSIST users in the selection of reliable and satisfactory respiratory protective devices, the Bureau of Mines bas established five schedules of minimum performance requirements for the approval of respirators. The current revisions of these schedules include 130 for self-contained breathing apparatus, 141F for gas masks, 19B and the amendments to 19B for supplied- air respirators, 21B for dust, fume, and .mist respirators, and 23B for chemical cartridge respirators. Copies of these schedules may be obtained from the Bureau of Mines, Publications Distribution Section, 4800 Forbes Avenue, Pitts- burgh, Pa., 15213. Approval tests on respirators are performed only at the request of the manufacturer of the respirator and at his expense. If the deice meets the approval requirements, a certificate of approval is granted on the complete respirator. This certificate states that as long as the respirator is manufactured as originally approved, or in accordance with any changes covered by an extension of the original approval, the manufacturer may advertise and sell his respirator as being approved by the Bureau of Mines. Many industries and regulatory agencies require that respirators approved by the Bureau of Mines he used where respiratory protection is needed. The Bureau of Mines, however, has no regulatory power over the use of the respirators that it approves. It acts as an impartial testing agency to insure the availability of suitable and safe respirators.

Jan 1, 1966

By D. F. Hambley

This report documents the work carried out by Engineers International, Inc. and its subcontructor, W. G. Pariseau, in order to develop a design manual for ore passes for open pit mines. The work included an extensive information search, novel analyses in rock flow theory, cost and time estimation for shaft and raise construction methods, and development of design criteria for the are pass proper, dump point, and draw point.

Jan 1, 1983

By R. Havens

During the course of the investigation of possible domestic sources of manganese, engineers of the Bureau of Mines examined and sampled two manganese mineral deposits in northeastern Utah. The Daggett Chief claims are situated in the northern part of Daggett County,5 miles southwest of Manila, Utah, and approximately 57 miles from Green-River, Wyo. Owners of the property are J.E. Harris Of Salt Lake City, Utah, Nels Palleson of Manila, Utah, and J. P. Larson. The manganese occurs in a vein 6 to 8 feet wide in a shale and sandstone formation. Two distinct occurrences Of manganese are present Within the vein, and samples of each were subjected to testing. Lot A, representing .probably the major portion of the Manganese; was composed of nodules and veinlets of manganese oxides in a semicompact; gray, shaly formation. Lot B represented a 15-inch vein of dense iron-manganese ore. .Most of the laboratory work at Salt Lake City, Utah, was done on these two samples; but preliminary testing also was carried out on a small sample, physically similar to lot A, submitted by the owners.

Jan 1, 1949

By G. R. Hopkins

According to reports received by the Bureau of Mines, Department of Commerce, as of January 1, 1929 there were 413 completed refineries in the United States, with a total daily crude-oil capacity of 3,509,540 barrels. In addition, 14 refineries, with a potential capacity of 99,000 barrels, were being constructed. Of the completed refineries, 341, with a capacity of 3,325,890 barrels, or 95 per cent of the total capacity, were in operation; and 72, with a capacity of 183,650 barrels, or 5 per cent of the total, were shut down. The improved condition of the refining industry in 1928 was indicated in several ways; namely, in an increase in the total capacity of the completed plants, in the opening up of a few plants which were shut down during 1927, in a decrease in the number of plants dismantled, and in an increase in the number of plants under construction. The majority of the refiners have followed a steady expansion program commensurate in most cases with the increase in demand for petroleum products. Obsolete equipment has been dismantled and modern equipment has been installed, with the net result that the total capacity of the completed refineries in the United States has shown a steady increase since January 1, 1918, the date of the first Bureau of Mines survey. Between January 1, 1928, and January 1, 1929, the number of completed plants fell from 423 to 413, but their total capacity increase 259,160 barrels, or 8 per cent. This compares with an increase in runs to stills of domestic and foreign crude petroleum of 10 per cent, and of domestic crude alone of 7 per cent.

Jan 1, 1929

By M. G. Zabetakis

Benzene and toluene are the first two members of an important homologous series whose general formula is CnH2n-6. The members of this series differ in composition from benzene by some integral multiple of CH2; they can all be prepared in the laboratory by the Wurtz-Fittig, Friedel-Crafts and Grignard syntheses. Because 'of the industrial importance of these-hydrocarbons, the limits of flammability of eight members of the series have been determined at 100° C.-(A temperature of 1000 C. was chosen because the determination of the upper limit of flammability of p-cymene requires an apparatus temperature. of at least 90° C. As elevated temperature data are available for other combustibles at 100° C. but not at 90° C., all data were taken at 100° C. in order to obtain comparable results.) Minimum ignition temperatures of these combustibles have been determined at laboratory-pressures.

Jan 1, 1951

By J. H. Wiggins

In 1919 the United States was threatened with a shortage of gaso- line. In spite of this well-known fact, a detailed field investigation has shown that in one stage only of handling crude oil the volume of gasoline that evaporates is equal to one-thirtieth of the country's yearly gasoline production. This loss occurs during the few days that the oil is stored on the leases before being taken by the pipe line, and in 1919, in the Mid-Continent field alone, it amounted to 122,100,000 gallons. Large as it is, it is only a part of the loss on the lease. Investigation has further shown that the gasoline in crude oil evaporates from one-half to six-tenths as rapidly as the same gaso- line after being distilled and stored, all evaporative conditions being the same. Many wastes in the oil fields are called "necessary." By this is meant that the cost of preventing the waste is greater than the gain through saving. Evaporation losses have fallen heretofore in this category, but now they must be considered unnecessary. In other words, it is no longer economical for any handler of crude oil to permit losses through evaporation. In accordance with its purpose of seeking to conserve mineral resources, the Bureau of Mines investigated the loss of gasoline by evaporation in the storage and handling of petroleum. Inasmuch as most producers had not decided that their losses justified cor- rective measures and no evidence was available on the comparative losses in various stages of handling the oil, the investigation was limited to determining by experiment and observation the nature and magnitude of evaporation losses, where the greatest losses are, and the factor controlling evaporation.

Jan 1, 1922

By A. C. Richardson

During the past two and a half years the U. S. Bureau of Mines and the University of Alabama, with the cooperation of the different coal operators, have been making an extensive study of coal preparation in the State of Alabama. Considerable time has been devoted to the study of the washing characteristics of the Mary Lee bed and the various methods used in preparing from it a low-ash coal suitable for the manufacture of metallurgical coke. One of the phases of this problem is the utilization of middlings products from the washing plants. This paper gives the results of treating jig middlings on a coal-washing table at the Bureau of Mines laboratory at Tuscaloosa, Ala. The sample used was secured from the Sayreton washery Of the Republic Steel Corporation, Sayreton, Ala.

Jan 1, 1931

By Edwin S. Secor

The Federal Bureau of Mines conducted a field survey of 153 bituminous coal strip and auger mines to estimate coal recovery from surface mines in the Eastern United States. Recovery was calculated from field data by measuring coal losses resulting from mining coal and leaving barriers. Mean total recovery for strip mining in States east of the Mississippi River was 83.0 percent and ranged from 72.3 percent for Tennessee to 91.3 percent for Maryland. Mining losses and barrier losses were 10.1 and 7.7 percent, with standard deviations of 4.8 and 10.4 percent, respectively, indicating that barrier losses, although less than mining losses, were more variable. Mean total coal recovery varied only slightly for the two regions studied; 82.7 percent for Appalachia and 84.3 for the Midwest. Total recovery grouped by mining method--contour, area, and mountaintop removal--was 79.8,84.7, and 85.3 percent, respectively. Mean auger recovery was 35.9 percent; of the total average loss of 64.1 percent, over one-half resulted from design limitations while the remainder was attributed to operating losses. The wide recovery range at individual mines indicates the variability of the eastern surface coal mining industry. Because of this, care should be exercised in applying the results of this report to reserve estimates other than those of a general nature.

Jan 1, 1977

By R. B. Anderson

SULFUR poisoning of iron catalysts in the Fischer-Tropsch synthesis was investigated at the Bureau of Mines, because synthesis gas produced from coal contains sulfur compounds. Tests of two typical iron catalysts with synthesis gas containing known concentrations of H2S were made to determine catalyst life as a function of sulfur concentration to ascertain the type of gas purification required. Fixed beds of activated steel turnings and a fused iron oxide catalyst were investigated in sulfur poisoning tests at 21.4 atmospheres with IH2+100 gas containing 6.9, 23, or 69 mg S as H2S per cubic meter (0.3, 1.0, and 3.0 gr per 100 cu. ft.). In tests of reduced catalysts at constant temperatures, more than 80 percent of the activity was lost when 0.5 mg S/g Fe was introduced. Poisoning of nitrided or carbided fused iron oxide catalysts to a given extent required more than twice as much sulfur than for the corresponding reduced catalyst. When the synthesis temperature was increased to compensate for loss in activity, tests of the fused iron oxide catalysts at constant productivity could be continued for 19 to 98 days. The tests were terminated by clogging of the reactor, presumably caused by carbon deposition. One objective of the present work was to determine if synthesis gas, purified by the Bureau of Mines' hot-potassium carbonate process for removing H2S, OOS, and CO2, is suitable for synthesis on iron catalysts. The sulfur content of the gas purified by tills process is in the range of concentrations used in the present work. In constant-productivity tests of nitrided fused iron oxide catalysts with synthesis gas containing 6.9 mg S/m3, catalyst lives are nearly long enough for serious consideration of tills mode of operation. However, factors relating to selectivity and stability of the catalyst indicate that this type of operation is impractical for a commercial process. On this basis additional gas purification, such as iron oxide boxes following a hot potassium carbonate scrubber, is desirable.

Jan 1, 1965

By Paul T. Allsman

The vanadiferous deposits of the Sublette Ridge and Salt River Range, 2 miles east of Raymond, Idaho, in western Lincoln County, Wyo., were examined August 24 to August 30, 1942, by an engineer of the Bureau of Mines, who was shown these properties by W. W. Rubey of the Geological Survey, Washington, D. C. The Sublette Ridge deposits are owned by the former U. S. Phosphate Co. H. F. Chaney, Portland, Oreg., is the representative for the company. The following report covers the history of the district, outlines the physical features and communications, mentions the property, and notes the ownership. The deposits and ore are described, and work performed by the Bureau of Mines is explained in detail. Ore-dressing tests and methods are explained.

Jan 1, 1949

By Bruce D. Sartwell

A program was written which utilizes a remote teletype input to a time- sharing computer to plot charged particle or X-ray energy spectra which are stored in the memory of multichannel analyzers. The program, written in FORTRAN V, accepts the data printed out by the pulse height analyzer on paper tape and then, after reading these data tapes into the computer, plots on the teletype the desired energy spectra on a scale automatically adjusted for the maximum number occurring in the data. The program is flexible enough so that the researcher can subsequently expand or contract the vertical (intensity) or horizontal (energy) scales. With a slight modification, the program will accept data printouts from scalers or analog to digital converters. The program also includes a feature for integrating the energy peaks obtained by pulse height analysis.

Jan 1, 1970