Search Documents

By C. Q. Cupps

n view of increased interest in secondary recovery of oil in the Cut Bank field, Montana, a review has been made of unpublished data obtained during a 1943-44 study of reservoir oil characteristics in this field. Considerable uncertainty was attached to interpretations of subsurface oil sample analyses from six Cut Bank zone wells, one Lander sand well, and one Moulton sand well, because of adverse sampling conditions and wide range in the data. Much of this uncertainty has been removed by this review which has shown two of the Cut Bank zone samples and the Moulton sand sample to be representative of the reservoir oils. Estimates of original reservoir oil characteristics derived from differential-liberation analyses of these samples show that the oil in the Cut Bank zone was initially saturated at the gas-oil contact pres-sure, 750 psia, and the oil in the Moulton sand was undersaturated with a saturation pressure of only 380 psia. The rest of the samples were indicated to be nonrepresentative of the reservoir oils because of a disproportional vaporization of heavier components of the solution gas. The vaporization of these components is believed to be a cumulative effect of contact of the oil with bypassing, light-gravity gas which had been liberated at higher pressures from solution in oil farther back in the formation, or which had come from the gas cap, rather than from the singular effect of gas evolution caused by excessively low bottom-hole pressures. Change of oil composition caused by the latter was found to conform closely to that occurring during a differential liberation of gas in the laboratory.

Jan 1, 1967

By Foster Fraas

Review of the literature on solid solutions discloses that the relation between composition and magnetic susceptibility is not linear . Recalculation using a transformation of composition values to parameter v values provides for a linear relation with the magnetic susceptibility to the 1/2 power . Application to minerals is illustrated by the olivine and enstentite series .

Jan 1, 1964

By Manuel Gomez

Coking time was investigated as a function of coal properties, carbonization parameters, and the interactions between these variables. The results indicate that coal properties and carbonization conditions interact to influence the coking time, and these interactions may be determined quantitatively. Prediction equations were developed and used to simulate the effects of bulk density, flue temperature, and oven width on coking times for coals having a wide range of properties. The data presented provide additional information on the carbonization process to permit the coke oven operator to maintain closer control of coke production and coke uniformity.

Jan 1, 1968

By R. L. Grant

During the last decade or more , experimental research on commercial detonators used for initiating the detonation of dynamite and other high explosives has led to important improvements . Developments , especially in the United States , have been directed toward improvement in the construction of detonators to make them safer to manufacture and use . More suitable and safer initiating charges also have been found . Although for many years mercury fulminate was unrivaled as the initiating charge for dynamite , during the last decade it has been replaced to a large extent by less sensitive , more efficient, and cheaper combinations of ignition , priming , and base charges . Commercial detonators were once of relatively simple construction and almost universally identical . Today they are technically complex, with special nodifications for particular uses ; they have developed along different lines n various countries and even among the several manufacturers within any one country .

Apr 1, 1943

By F. Matanzo

This guide considers only nine of the many wire rope terminations used in the mining industry so use of the information presented for terminations not specifically addressed can be done, but with some risk. The nine terminations considered are: Flemish Loop with Steel Sleeve & Thimble, Flemish Loop with Steel Sleeve, Wedge Socket, Swaged Socket, Turn Back Loop with Aluminum Sleeve & Thimble, Thimble Splice with Four Tucks, V-Bolt Clip with Thimble, Zinc Poured Socket, and Epoxy Resin Poured Socket. The guide uses pull test data, axial fatigue test data, and data on sensitivity to poor workmanship, to rank the nine terminations with respect to these performance measures. A selection procedure is suggested and illustrated with an example. Failure data is used to identify the common modes of failure of each termination and so help the inspector direct his attention to the likely location for a failure and describe what he should be looking for. The data on which this guide is based is included so that as new data becomes available, the ranking order can be adjusted accordingly.

Jan 1, 1978

By Piyush K. Dutta

This report describes the design, development and manufacture of a prototype quiet hard rock stoper drill and results of its field tests. It is shown that the stoper drill noise level can be reduced from 118 dBA to below 100 dBA by using this design. The design concept of this drill is based on a valveless independent rotation system, use of an integral muffler and pivot mount. The drill was manufactured in a standard commercial drill manufacturing setup and organization. The design and production technology proved that commercially viable quiet drills can be made available for mine use.

Jan 1, 1985

By Marvin W. Wilson

The Federal Bureau of Mines has conducted laboratory experiments simulating underground gasification of coal to study the feasibility and mechanism of the process and determine the chemical and physical characteristics of a coal-bed during gasification. Laboratory and small-scale field experiments also were made to investigate the properties of coal and other factors affecting the electrolinking-carbonization method of preparing a path through a coalbed before gasification. Laboratory experiments simulating underground gasification of coal: Experiments with a laboratory retort indicated that bituminous-coal deposits could be gasified in place to produce a combustible gas.

Jan 1, 1960

By J. R. Nettle

A method has been developed in the laboratory for successfully electro-refining titanium metal. Refining is accomplished in e fused-salt electrolyte using offgrade metal as the anode and collecting the purified metal at the cathode. The characteristics and requirements of the various alkali chlorides tested as electrolytes are discussed in relation to relative ease of purification and serviceability. The various types of cells designed and tested for electrorefining are illustrated and their method of operation discussed. The individual advantage of each cell and the purpose for which it was designed are reviewed. The magnitude of the cathode current density was found to depend largely upon the quantity of soluble titanium chloride in the electrolyte. The physical condition of the anode also greatly affected the cathode current density.

Jan 1, 1957

By W. I. Garms

This paper, describing the milling practices at the Hayden concentrator of the Nevada Consolidated Copper Co. is the first of a Series being prepared by the Bureau of Mines on milling methods and costs in various districts of the United States. The Hayden concentrator is located at Hayden, Gila County, Ariz., 20 miles from the mine at Ray, Pinal County, Ariz., and approximately 1-1/2 miles north of the junction of the Gila and San Pedro Rivers. During the fourth quarter of 1928 the concentrator treated daily by flotation an average of 10,336 tons of ore containing 1.25 per cent of copper. The average recovery during this period amounted to 87.84 per cent of the total copper. The concentrates contained 19.88 per cent of copper.

Jan 1, 1930

By Thomas M. Barczak

The effect of load rate on the load-carrying capabilities of wood cribs is investigated in this Bureau of Mines study. The modulus of deformation (stiffness) of wood crib blocks has been shown to increase with increases in rates of load application, causing larger load reactions for increases in convergence rates. Since wood cribs are tested in the laboratory at convergence rates that are orders of magnitude faster than typically would occur underground, wood cribs tested in the laboratory will react larger loads than the same cribs would react underground for the same displacement. Tests conducted in the Bureau's mine roof simulator on green wood crib blocks indicate that the increase in stiffness for increasing load rates diminishes at displacement rates beyond 0.1 in/min, making crib load nearly independent of load rate for rates faster than 0.1 in/min. Seasoned wood specimens were not as con-sistent in load-rate dependency. Some possible explanations of observed load-rate behavior on wood crib specimens are also postulated in this paper.

Jan 1, 1988

By John E. Hamak

The U.S. Bureau of Mines estimates the identified helium resources of the United States at 630 Bcf as of December 31, 1990. This includes 295 Bcf of demonstrated reserves, 87 Bcf of demonstrated marginal reserves, and 42 Bcf of demonstrated subeconomic resources. The identified resources include 161 Bcf of helium in inferred and marginal reserves and 45 Bcf in inferred subeconomic resources. The identified helium resources contained on Federal lands are approximately 170 Bcf, including 32 Bcf in underground storage in the Cliffside Gasfield near Amarillo, TX. In addition to the identified helium resources, undiscovered helium resources in the United States are estimated at a most likely volume of 103 Bcf, with a maximum volume of 259 Bcf and a minimum volume of 41 Bcf. Also reported are 43 Bcf of helium in nonconventional and low-helium-content natural gases. Current extraction of helium in the United States occurs mostly from natural gases produced from the Hugoton gas area in Kansas, Oklahoma, and Texas, and the Riley Ridge area in southwest Wyoming. Helium extracted from natural gas in the United States in 1990 was 2.5 Bef. If current trends continue, some shortfalls in helium supply may occur in about 5 to 10 years.

Jan 1, 1993

By R. Blickensderfer

An impact wear testing machine was devised by the Bureau of Mines that simulates the repeated impact conditions encountered in large milling and grinding operations where breakage and spalling are problems. The apparatus provides data on materials that may help in the design of alloys with improved resistance to deformation, spalling, and breakage. The test blocks are 2 in thick by 6 in by 8 in. Impacts are produced by dropping 3-in-diam balls weighing 4 lb from a height of 10 ft. Tests were run until breakage occurred or to a total of 100,000 impacts. Four types of failures of the test block were observed: (1) cold flow of the bulk material by plastic deformation, (2) flaking of the surface in the impact region, (3) spalling of the block to form a crater in the region of impact, and (4) breakage of the test block into two or more major pieces. The effects of composition, heat treatment, microstructure, and hardness on types of failure are discussed.

Jan 1, 1983

By D. E. Redmon

The Federal Bureau of Mines has studied the locations and general features of 90 pegmatites found in north-central New Mexico. The dominant valuable product of the pegmatites is muscovite, both sheet and scrap. However, the Harding pegmatite in Taos County is mined only for beryl. Many attempts have been made to recover scrap mica on a large scale by mechanical beneficiation of pegmatite, but the operations heretofore have been short-lived. The Globe mine and the Apache mine, both near Petaca in Rio Arriba County, have been the most important sources of sheet mica in New Mexico. Recognition of the growing need for some of the minerals derived from pegmatites led the Bureau of Mines to investigate the occurrences of pegmatite.

Jan 1, 1961

By Gregory J. Chekan

The U.S. Bureau of Mines is investigating longwall panel and gate road layouts to increase coal recovery and reduce multiple-seam interactive problems. This report presents design practices for longwall mining multiple seams to provide mine planners and operators with practical guidelines for designing productive longwall mines. Key aspects of mine design that control longwall interactions are examined, including sequencing of seams, design of gate road pillars, and orientation of gate roads and longwall panels. Theories that describe stress transfer between multiple scams and the mechanics of interaction are addressed in relation to geology. Common longwall designs were further investigated using a boundary element model, MULSIM/NL. The model provided insight into relative stress transfer and distribution that occurs between longwall operations in multiple seams. Findings from the model show that (1) a longwall panel should be mined from the gob to the solid coal of an overlying mine, because the stress concentrations are lower; the approach angle should be kept under 30°; and (2) when mining in descending order, superpositioning gate roads usually produces the worst stress condition. To prevent this, the overlying isolated gate roads should be positioned from the centerline toward the headgate side of the underlying panel.

Jan 1, 1993

By Donna L. Anderson

This information circular documents the status of a laser-based guidance system to track and control the tramming maneuvers of a continuous mining machine. The work is part of a multiple project effort at the U.S. Bureau of Mines to develop technology for computer-assisted mining systems. The system includes stationary offboard laser-scanning sensors that report the angular coordinates of retroreflective targets on the mining machine. A microcomputer system processes the angular coordinates, determines position and heading, handles requests for data, and controls tram maneuvers of a continuous mining machine. This report describes the hardware for the sensor and computer systems and the software algorithms for continuous miner position and heading determination, closed-loop tramming, and data request handling. Improvements made to the system since previous documentation include the rewriting of the software on a stand-alone real-time microcomputer system, the implementation of real-time programming techniques, the use of a new version of the laser sensor, and the design and development of explosion-proof enclosures for the lasers and corresponding power supply.

Jan 1, 1991

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items is confidential. It presents analytical data for 3,924 samples, representing the products of 116 companies. The samples were collected during June, July, and August, 1954. As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers, The data were obtain& by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation, A list of the National Motor-Gasoline Survey reports published during the past 10 years is given on page 5.

Jan 1, 1955

By Forrest T. Moyer

Need for lightweight building materials was created in the latter part of the nineteenth century by a radical change in building design in which dead load or structural weight was transferred from thick, heavy, load- bearing walls of former construction practice to a load-carrying framework of beams and columns with thin walls. This new design was brought about by the introduction of structural steel followed by reinforced concrete and structural concrete as materials for the erection of the load-supporting frame. The new materials and method of construction made possible the erection of skyscrapers and the building of bridges with long spans, and made feasible additions of one or more floors to existing buildings. As size and design of the load-bearing framework are controlled chiefly by dead load, the natural result was a. search for and use of light- weight materials in partitions, floors, and exterior walls. However, these thin walls created problems of heat and sound. insulation, so that building materials which possessed good heat- and sound-insulating properties in addition to light weight were objects of extensive research. One group of materials developed to fill this need comprised lightweight concretes, of which some were obtained by the use of lightweight aggregates. Although the advantages of lightweight.materials were evident from the first skyscrapers, there was a transition.stage.between the old bearing- wall and modern skeleton-frame types of building, with the heavy and massive construction of the former superimposed upon the latter. Hence, it was not until the period between 1910 and 1930 that the new lightweight concretes were recognized and used more extensively in the erection of large, nonresidential buildings. From this type of construction, light- weight-aggregate concretes entered-fields of residential and small non- residential building; in which they were found desirable for production of prefabricated, large-size; masonry units. Although the weight of each unit was reduced sufficiently to enable one man to handle it easily, properties of the new concretes other than light weight were the principal factors in the ready acceptance of these new materials in residential building. Manufacture of precast units includes complete lines of masonry and back-up blocks, bricks; floor beams, columns and partition, roof, and floor tiles and slabs. Recent improvements in casting machinery, development of the vibration-pressure machine, and a more thorough study and knowledge of the requirements and properties of the concrete mix have all contributed materially to the rapid expansion in use of lightweight aggregates in this industry.

Jan 1, 1942

By Robert R. Stein

Occupational noise caused by the rock drills used in mining was investigated by the U.S. Bureau of Mines. Using a large reverberation chamber and an automated drill test fixture (ADTF), the sound power levels of mining drills were measured to determine if there are types of drills that are advantageous from a noise production standpoint. Test results show that while there are not large variations among types of drills, there are still some choices that could produce a positive effect on overall noise exposure. It is also shown that lower noise exposures are possible using larger drills because of higher production rates and better operator positioning.

Jan 1, 2010

By F. M. Boler

The U.S. Bureau of Mines conducts research at the Galena Mine, Wallace, ID, with the aim of mitigating the effects of rock bursting. Destress blasting is commonly used as a stress control technique at the mine. A digital seismic array and an array of borehole pressure cells (BPC's) had been installed near the site of a stope undergoing mining and periodic de stressing. The instrumentation was being monitored at the time of a destress blast of the 46-99 stope. No significant seismic events occurred coincident with the destress. However, the destress was followed by a 2 ½ -week period of increased seismic activity, including two damaging events on February 7, 1990, at 034500 (hour, minute, and second) and 122020 Pacific standard time. BPC measurements indicated coseismic ground pressure changes on the order of 200 to 300 kPa associated with the damaging events. Fault plane solutions and dislocation models established that stress changes induced by the event at 034500 may have been significant in promoting the occurrence of the event at 122020. Theoretical investigations suggest that applying knowledge of the existing stress field, an understanding of rock burst mechanics, and fracture mechanics principles can improve destress effectiveness.

Jan 1, 2010

This report covers the work performed by the Advanced Products Division of FMC Corporation under Bureau of Hines Contract J0155166, Design Evaluation for Development of an Advanced Bolter Module. FMC has evaluated the existing ISMS bolter designs, and the corrections and improvements in progress, including the effect of the three-chain magazine presently being fabricated, and recommends that a complete bolter module featuring a new magazine, safety post and lower stabilizer or similar device be designed, fabricated, and tested, A 29 week program is proposed which includes a four week demonstration. This module would eliminate those reliability problems not presently being solved and would provide a reliable bolter module for a production oriented miner/ bolter.

Jan 1, 1975