Search Documents

Permit visual inspection of underground cavities dam the surface. Approach A closed circuit TV camera and a 35mm still camera are lowered down a borehole, and remotely operated. How It Works A platform holding the cameras, and other equipment is lowered on a graduated cable until the depth of interest is reached. Then a quartz lamp and the TV camera are turned on. The television picture is monitored at the surface and recorded on video tape. Areas of special interest are photographed with a 35mm still camera. These photographs contain more detail than TV images because photographic film is capable of higher resolution than a TV transmission.

Jan 1, 1979

By B. K. Cantrell, K. L. Rubow

"Quantifying exposure to diesel exhaust aerosol in an underground coal mine depends on the ability to measure this component of respirable mine aerosol separately from coal dust. Such measurement is complicated by the carbonaceous nature of both the diesel and coal dust particulate that make up the respirable aerosol. Hence, special sampling and analytical techniques must be used to distinguish between these two aerosol components.As part of a continuing study of diesel exhaust aerosol characteristics, the U.S. Bureau of Mines has applied size selective sampling together with gravimetric analysis to separate and measure respirable diesel exhaust and coal dust aerosol concentrations in diesel-equipped underground coal mines. This technique is based on the premise that the diesel portion of the aerosol is predominantly submicrometer and the mineral dust portion is mostly greater than 1 µm in size. In the study, chemical mass balance (CMB) modeling, based on the distribution of chemical elements in aerosol and aerosol source material samples, is used to referee the analysis of diesel exhaust and mineral dust aerosol concentrations from the size selective sampling results.Based on the results of the study, the Bureau, in cooperation with the University of Minnesota and the U.S. Mine Safety and Health Administration (MSHA), have developed a prototype personal diesel exhaust aerosol sampler for underground coal mines. The sampler has three stages: a preclassifier stage to select for respirable aerosol, an inertial impaction stage with an aerodynamic diameter(d) size cut at 0.8 µm to separate diesel aerosol from mineral dust and collect the mineral dust, and a final filtration stage to collect the diesel fraction of the sample. The sampler has been evaluated in both laboratory and field experiments conducted by the Bureau, MSHA, and the Generic Minerals Technology Center for Respirable Dust (GMTC-RD)."

Mar 1, 1992

To recover metals as sulfide concentrates from contaminated waste streams using hydrogen sulfide (H2S) generated by the bacterial digestion of waste organic materials. Approach The goal of this research is to develop a treatment method for metal mine effluents that will rival the cost and convenience of conventional lime treatment, and that will provide better effluent water quality, result in less expensive sludge disposal, and allow for the selective recovery of metals.

Jan 1, 1993

By P. W. Jeran, M. C. Irani, D. H. Lawhead

The methane emissions from an advancing coal mine section were continuously monitored for 120 days. During this time, the section advanced 2,000 feet into virgin Pittsburgh coalbed producing 54,565 tons of coal with a total methane emission of 91 million ft3. Analysis of the data gathered showed that daily methane emissions did not correlate with overburden thickness and daily coal production. A good correlation was found between the daily methane emission and the average length of rib exposed to virgin coal.

Jan 1, 1976

By Wesley T. Holmes II, Lloyd H. Banning

Electric - smelting studies were made on titaniferous materials obtained from the Klukwan and Snettisham , Alaska ; Choteau , Mont .; and Iron Mountain , Wyo . , deposits with the objective of determining the feasibility of producing pig iron and an enriched titania slag in one test series and pig iron alone in another test series . In addition , related studies were conducted to determine the amenability of Choteau crude ore to wet -magnetic separation and to determine the quality of steel that could be produced from the titaniferous pig iron . The continuous smelting tests were made in a three - phase , submerged - arc , electric furnace , and the laboratory steelmaking tests were made in a singlephase electric - arc furnace . A continuous , belt - type , wet - magnetic separator was used in conjunction with a ball mill and a spiral classifier in recovering titaniferous magnetite from the crude Choteau ore . Pig irons containing less than 0.05 percent phosphorus or sulfur were readily produced from the titaniferous materials ; iron recoveries ranged from 92 to 98 percent . The Choteau ore was ground to minus 65 - mesh to produce a concentrate containing 60 percent or more iron . The steel produced from the titaniferous pig iron was a high - quality product .

Jan 1, 1964

By Edward A. Barrett, Lynn L. Rethi

From 1987 through 1996, 13 fatalities occurred at underground operations in the U.S. stone mining industry. A review of the underground limestone mine industry data for this 10 year period indicated a high fatality concentration in one area: ground failures.

By Thomas C. Denton

The Old Reliable copper mine was first examined by Harlow D. Phelps , an engineer of the Bureau of Mines , in October and November 1942 , in compliance with a request from the War Production Board , which furnished copies of assay maps of the 100- and 200-foot levels and requested that they be check-sampled . The author and R. li. Grantham and W. D. Hughes , engineers of the Bureau , made a second and more detailed examination later , after a number of manways had been opened that were inaccessible when the first examination was made .

Feb 1, 1947

By W. E. Lamont, R. E. Perry, I. L. Feld

The Bureau of Mines conducted research to determine the conditions required to sinter a pyrrhotite calcine into a product suitable for iron blast furnace feed . The calcine , a fine - grained iron oxide produced by roasting sulfide flotation concentrate , analyzed about 60 percent iron and 1 percent sulfur . Sintering of the calcine without prior pelletization was not successful whereas firing of preformed calcine charges yielded acceptable sinter products . Batch tests were made to study the effect of the following variables on the sinter quality : Size of green pellets in the charge , quantity and type of internal carbonaceous fuel used , depth of sinter bed , moisture content of the charge , flux additions , and binder additions . The batch and continuous sinter tests showed that minus 1 / 4 - inch pellets prepared from a mixture of the calcine , coke , dolomite , and water gave sinter cakes analyzing 57 to 61 percent iron and 0.05 to 0.02 percent sulfur .

Dec 1, 1963

By Paul T. Allsman

Iron-ore deposits in southwestern Utah, as the major source of iron ore for western steel plants, were investigated by the Bureau of Mines in 1942-45 in cooperation with property owners and operators and with the assistance of the United States Geological Survey with a view to determining and extending the known reserves. The factual data resulting from that project were presented in a previous report and in a report on the geophysical surveys now in course of publication. The present report has been prepared in response to expressed public interest in the ore reserves of Iron County. Mining began in the district in 1871} but. did not become important until 41 1923. From 1923 to 1946, inclusive) production totaled 10,139,500 long tons. In 1945 the district yielded 1,931,749 long tons containing 52.84 percent iron; in 1946 the corresponding figures were 1,317,671 and 53.75. The deposits lie .in a narrow, 23-mile long belt extending northeasterly from Washington 'County into Iron County along a line of mountains, chief of which are Iron Mountain, Granite Mountain, 'and Three Peaks in Iron. County. The deposits are hematite-magnetite bodies, chiefly in limestone near its contact with the monzonite of the mountain masses, but with a few important veinlike bodies in the monzonite or at the contact. They range in size from small pods to several millions of tons, and in depth from surface or near-surface to a known maximum of 1,300 feet:

Jan 1, 1948

By D. G. Foot

The Bureau of Mines devised a direct flotation method for recovering potash from carnallite (KC1?MgC12?6H20) ore characterized by a high content of water-insoluble impurities. The method includes (1) a decomposition leach of the carnallite, (2) flocculation-depression of the insoluble slimes, (3) potash rougher, cleaner, and recleaner flotation, and (4) final product leaching. The technique eliminates the necessity for removing the water-insoluble slimes by mechanical or flotation de-sliming. Laboratory results demonstrated that the direct flotation procedure, when compared with conventional techniques, yielded equivalent or improved flotation results with equal or less reagent consumption. Locked-cycle testing of the direct flotation method recovered 87.8 pct of the potassium in the flotation feed in a final product containing 60.6 pct K20. A flowsheet incorporating the carnallite leaching-potash flotation procedure is presented.

Jan 1, 1982

By Jeffrey Johnson, Thomas Brady, Radford Langston, Mary MacLaughlin, Hendrik Kirsten

The magnitudes and directions of in situ stresses affect the stability of mine openings, as well as the type and amount of ground support needed to maintain a safe working environment for miners. Using hollow inclusion stress cells, researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health obtained two in situ stress measurements from the face of two footwall lateral drifts at the Stillwater Mine near Nye, MT. The first measurement, obtained in 1997, was collected under the valley beneath the Stillwater River. The second measurement was obtained in 2002 under the main frontal massif of the Bear tooth Mountains in the western sector of the mine. Although few data are available, the major principal stress under the valley has been recorded as nearly horizontal in a north-south direction perpendicular to the ore body, while beneath the mountains, stress runs east-west parallel to the ore body. This paper documents the measurements, describes the in situ stress state, and discusses a finite-difference analysis of the biaxial test.

By J. M. Stuve

The present Bureau of Mines investigation measured low-temperature heat capacities of NiBr2 (8 to 302 K) and NiS04 (9 to 70 K) by adiabatic calorimetry. The standard entropies (S°, 298.15 K) of NiBr2 and NiS04 were calculated as 29.26 ± 0.06 cal/deg mole and 24.21 0.04 cal/deg mole, respectively. (1 cal = 4.1840 joules.) Heat-of-solution measurements of anhydrous NiBr2 were used to determine its enthalpy of formation (?Hf°, 298.15 K) as -50.64 ± 0.31 kcal/mole. High-temperature enthalpies of NiBr2 and NiS04 were measured by drop calorimetry to 1,150 K and 1,002 K, respectively. Enthalpies, heat capacities, and related formation functions are tabulated to 1,200 K.

Jan 1, 1978

By M. K. Larson, J. K. Whyatt, R. B. Langston, J. C. Johnson, H. Kirsten, T. M. Brady

An experiment is described in which hollow inclusion cells (HICells) were used to measure stress in a jointed rock mass during drift development at the Stillwater Mine, Nye, MT, USA. Two HICells were installed in the footwall approximately two drift widths ahead of the face. One HICell was over cored and then immediately tested in a biaxial chamber. The other HICell was left in place and monitored as the drift was excavated in three advances, each one-half the width of the drift. Strains were recorded hourly by a datalogger. Results show that there was little stress change during the first and second drift advances, but that a large stress change occurred after the third advance. The measurements also showed that the in situ principal stress directions lined up with regional geologic structures. Stress changes during face advance were likely caused by deformation along localized joint sets and inelastic deformation near the face.

By J. R. Hauger, P. A. Romans, W. J. Niebuhr

With suitable instrumentation and techniques it is possible to determine the presence of tantalum in columbium to 20 ppm . This paper discusses the selection of X- ray spectrographic instrumentation and describes a technique for accomplishing the low level determination of tantalum . An ion- exchange method of separating tantalum from columbium is also described .

Jan 1, 1964

To develop a system which will effectively detect and extinguish fires in underground fueling areas while also providing a warning for nearby miners. Approach A system involving optical fire sensors. automatically-released dry chemical and aqueous film-forming fluid (AFFF) fire suppressants, and automatic alarms was designed from off-the-shelf, state-of-the-art components, and was in-mine tested at two mines in the two typical underground fueling area situations: fuel transfer areas and fuel storage areas. How It Works As mines become more mechanized, the number of fire hazards increases since fueling areas are more abundant. Fire hazards are especially serious in deep mines, since escape time is longer. To help solve this growing problem, the Bureau of Mines, in cooperation with the Mine Safety and Health Administration (MSHA) and the National Fire Protection Association (NFPA), has developed and in-mine tested a cost-effective fueling area fire protection system. The system was designed to be rugged enough for reliable, long-term use, yet to utilize state-of-the-art, off-the-shelf components to maintain cost-effectiveness. The system consists of cross-zoned, ultraviolet flame sensors used for quick response to fire, and a dual-agent fire suppression subsystem. A dry chemical is used for fast fire -knockdown," and AFFF (or "light water") is used for long-term, fire-securing capability. The basic components of the system are shown in the schematic illustration.

Jan 1, 1982

By Henry M. Harris, Hal J. Kelly

Electrical dewatering tests are described in which the laboratory cells were designed for continuous operation using an endless metal belt as the anode . The test slurries were dilute , containing from 2.5 to 14.4 percent solids (specific gravity of 1.02 to 1.10 ) that were all minus 8 microns in size . Recovery of the solids of low water content was the practical objective of the investigation . Process variables evaluated and reported are : The effect of feed rate , amount of electrolyte , samples from different sources , and the use of two cells in series . These variables are evaluated on the basis of yield of clay per kilowatt - hour , recovery , and the amount of solids in the deposited clay . Recovery , yield , and solid content of the belt anode product are interdependent , and changes that will improve one of these characteristics often are accomplished at the expense of the others . Tests in which recoveries range from 50 to 60 percent usually result in yields of 8 to 9 kilograms (kg ) of dry clay per kilowatt- hour (kwhr ) . Under these conditions , the solid content of the deposited clay approximates 50 percent . One test sample , composed of kaolinite , showed very high yield , 13 to 16 kg per kwhr ; high recovery , 53 to 58 percent ; and 52 to 54 percent solids in the cake .

Jan 1, 1964

By J. M. Stuve

Heat of solution measurements of high-purity neodymium metal and neodymium trichloride (NdCls) in 4.360 molal hydrochloric acid (HCI) were used to determine the standard heat of formation (6EPr) of NdCls? From solution data obtained, the heat of formation of NdCls (c) was computed as -248,970 ±260 cal/mole at 298.150 K.

Jan 1, 1965

By A. L. Johns, M. V. Healey

This paper presents one of a series of digests of foreign mining legis- lation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of tie laws of Ecuador has been prepared from the best available information in Washington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State..

May 1, 1930

Roof falls continue to be the greatest single safety hazard faced by underground coal miners. During 1996-99, 44 coal miners lost their lives in rock falls, and nearly 2,400 were injured. In addition, nearly 6,000 noninjury roof collapses were reported. Roof supports are installed to protect the miners, but support system failures contributed to most of these incidents. Reducing the terrible toll taken by ground falls continues to be a major goal of research by the National Institute for Occupational Safety and Health (NIOSH). The purpose of these proceedings is to provide the mining community with a comprehensive survey of coal mine roof supports. Drawing on many years of research undertaken by the NIOSH Pittsburgh and Spokane Research Laboratories, this volume describes what types of support are available, how they work, and when they should be used. The major subjects covered include roof bolts, standing roof supports, cable supports, and longwall shields. Some special topics are also addressed, including an analysis of roof fall accident statistics, techniques for better skin control, material handling considerations, and longwall mining through recovery rooms. This proceedings volume also contains information on several important new technologies, which are described here for the first time: •Guidelines for selecting roof bolt length, pattern, and capacity that were derived from statistical analysis of the roof fall experience at 37 underground mines; •A new design method for longwall tailgate supports; and •A technique for measuring loads developed within cable bolts. The papers in these proceedings were presented at open industry briefings conducted by NIOSH on New Technology for Coal Mine Roof Support. The briefings were held in Norton, VA, Charleston, WV, Evansville, IN, Tuscaloosa, AL, Price, UT, Glenwood Springs, CO, and Washington, PA. The papers were also presented at the Mine Safety and Health Administration (MSHA) Preventative Roof-Rib Outreach Program (PROP) Seminar, which was held at the National Mine Health and Safety Academy near Beckley, WV.

Jan 10, 2000

Provide reasonably priced, reliable fire protection for large walking draglines. Approach Fire hazards on large draglines were analyzed, then appropriate automatic fire sensing and suppression systems developed and in-mine tested. How It Works Five fire hazard areas identified for special attention are: electrical control room, high voltage transformer enclosures, circuit breaker rooms, collector ring/roller path area, and the automatic lubrication rooms. Automatic fire sensing and suppression systems were separately designed for each area. The design of each system was tailored to the hazards and equipment protected. Spot thermal sensing and Halon 1301 suppression were specified for the electrical

Jan 1, 1981