Search Documents

By J. H. Holden

Operations involving the processing of coal, oxygen, and steam into synthesis gas by means of two pressure-type gasifiers have demonstrated the effect of heat loss and operating variables on carbon gasified and oxygen and coal requirements. Carbon gasified is the fraction of carbon in the coal that is converted to gas. Oxygen and coal requirement is the quantity of each that is needed to produce a unit volume (M std. c.f.) of carbon monoxide and hydrogen. Operating pressure of the gasifiers ranged from 150 to 300 p.s.i.g. and coal was fed at 200 to 500 lb./hr./cu.ft. of reaction-zone space. Oxygen-to-coal ratios were 8.5 to 10.5 std. c.f./lb. Heat loss and residence time have opposite effects on carbon gasified; increasing the heat loss decreases the carbon gasified, but increasing the residence time (by raising the operating pressure or reducing the coal-feed rate) increases the carbon gasified. The effects of these two factors are difficult to separate because they usually change simultaneously. A comparison of the results obtained from the operation of two gasifiers with different levels of heat loss, however, permitted the effect of heat loss to be separated from that of pressure and coal-feed rate. When the results were deter- mined on the basis of constant heat loss, increase of the residence time increased the carbon gasified until the reaction virtually had come to completion. For example, at 150 p.s.i.g., decreasing the coal-feed ratio from 500 lb./hr./cu.ft. to 200 lb./hr./cu.ft. substantially increased the carbon gasified. At 300 p.s.i.g., however, changing the coal-feed rate had little effect on the carbon gasified because the reaction had almost reached completion and further increase in residence time resulted only in a negligible change.

Jan 1, 1962

By O. C. Blade

Total sales of diesel fuel in the United States continue to Increase. This growth is due primarily to two causes: More conversion to diesel units by the rail-roads In recent years, and the greater use of diesel engines in trucks, busses, and tractors. Following are some figures on the distribution of the fuel computed from data issued by the Bureau of Mines.2/ [ ] Deliveries of diesel type fuel from refineries totaled 91,522,000 barrels during the first six months of 1955,3/ corresponding figure for 1954 was 91,170,000 barrels. Information on the properties of this engine fuel is very important to the petroleum industry, engine manufacturers, and consumers. To supply such information the American Petroleum Institute and the Bureau of Mines, United States Department of the Interior, under cooperative agreement, are conducting annual surveys of diesel fuel oil produced in refineries in this country.

Jan 1, 1955

By Forrest T. Moyer

INJURY experience and employment data are presented in this (chapter for metal and nonmetal mines, stone quarries, sand and gravel pits, iron-blast-furnace slag plants, and metallurgical plants (including ore-dressing and nonferrous reduction plants and refineries) in the United States. Employment and injury experience data for all mineral industries are given in volume III. The 1963 figures are preliminary and are subject to revision. METAL MINES Preliminary estimates for the metal-mining industry of a combined fatal and nonfatal injury-frequency rate of 32.34 per million man-hours in 1963 indicate only a slight change from the rate of 32.00 in 1962. Metal operations had 41 fatal and 3,110 nonfatal injuries during 1963.

Jan 1, 1964

By J. P. Morris

An experimental blast furnace in normal operation was quenched by substituting cold nitrogen for the hot blast air. More than 2,200 samples from the stack, bosh, and hearth were taken; 500 of these were selected for detailed analysis. Deductions are made as to the patterns of burden movement and gas flow; the reduction of iron oxides, including a comparison of ore and sinter; and the behavior of sulfur above the smelting zone. Metal and slag beads from the bosh were analyzed, as were samples from the hearth metal and slag. A brief description of a petrographic examination of the quenched burden is included.

Jan 1, 1963

By George S. Rice

The following paper was presented at an International Conference on Mine Safety Research held at Dortmund, Germany, September 23-28, 1935, inclusive. This conference was attended by representatives of Belgium, France, Germany, Great Britain, and the United States ands by invitation, Czechoslovakia, Poland, Spain, and Russia. The first international conference of representatives of mine-safety, research stations was held the United States Bureau of Mines Pittsburgh Experiment station in 1912 .4/

Jan 1, 1936

By G. Ahnell

Throughout portions of four (4) heavily mined Appalachian states subdivided by the Mine Safety and Health Administration (MSHA) as: District 3 -Northern West Virginia and Maryland; District'" -Southern West Virginia; District 5 -Virginia; and District 6 -Eastern Kentucky, active coal mine waste embankments associated with mechanical and/or chemical coal processing facilities of various levels of coal preparation were inventoried. For each site plant specifications, disposal techniques, embankments' characteristics, and coal source data were accumulated. Mapping at 1: 24, 000 and 1: 250,000 scale and Disposal Site Characterization forms were developed to present the findings. Associated abandoned surface and underground openings near each site were also indicated as well as locational data for each site and the areas environmental conditions - temperature, precipitation and vegetation types. A state-of-the-art review of coal preparation, waste disposal, and alternative uses of coal waste is also included.

Jan 1, 1982

By W. M. Deaton

The formation of gas hydrates in natural-gas pipe lines depends on temperature and pressure conditions in the lines as well as on the presence of condensed water. The operating pressure in a pipe line may be determined easily and usually is available from the records of operation, but the temperature seldom is known. In cooperation with the American Gas Association, the Bureau of Mines, in its investigation of gas hydrates, conducted a pipe-line-temperature survey and studied underground temperatures at depths at which pipe lines ordinarily are buried and the relationship of these temperatures to prevailing atmospheric conditions. A similar but mere limited study of this type was conducted by engineers of the Bureau of Mines a number of yours ago.4/ A summary of the earlier findings was included in a general report by the Bureau on the flew of natural gas through high-pressure transmission lines.5/ In the present study, data on temperature variations were obtained at several places widely separated geographically. This information should assist pipe-line engineers in designing and operating natural-gas pipe lines.

Jan 1, 1941

By Sterling J. Anderson

To define the technical competence and capabilities of a nonexplosive excavation concept, the Bureau of Mines conducted reduced-scale laboratory tests of a mechanical excavation tool called a rock splitter. Hydraulically actuated splitters, capable of generating both radial and axial loads on a predrilled hole, were designed and fabricated. Through paired variable testing and drifting simulation, reduced-scale splitter performance was evaluated in concrete. Testing proved that the rock splitter is capable of excavating within the highly confined drift set-ting and that it offers a distinct advantage over splitters that can generate radial loads only.

Jan 1, 1982

By George A. Morgan

Output of mineral products was estimated to be unchanged in 1983 from that of 1982 with the exception of petroleum. The country began production of crude oil from the Seme Oilfield, and all output was exported. Wd and charcoal constituted 72% of Benin's total energy consumption, and imported petroleum products and electric power accounted for the remainder. Cement was produced from imported clinker. The gross domestic product (GDP) was $1,061 million in 1982, the latest year for which information was available.2 COMMODITY REVIEW Gold.-Exploration was underway at Perma by the U.S.S.R. as part of the United Nations development program. Gold had been produced previously at Perma, where a grade of 0.289 troy ounce of gold per ton was reported, An exploitation program for the deposit was to employ about 100 people, and output was targeted to reach 1,600 troy ounces per year. Recoverable reserves were put at 96,000 troy ounces.

Jan 1, 1985

By J. Sottile, J. L. Kohler

Component failures in the electrical control circuits of mining machines account for a large percentage of the total downtime of the machine. Once a failure has occurred it is always a tedious and usually a time-consuming task to locate the failed component. Moreover, the pressure to quickly locate the cause of a delay can lead to compromises in safety. Thus an onboard diagnostic system, essential for an automated machine, would be a very useful addition to existing machines. This report details U.S. Bureau of Mines development of a generic procedure for synthesizing diagnostic systems for electrical-control-circuit failures in mining machinery. A continuous mining machine is used as the testbed to illustrate the application of the developed methodology. Substantive differences among mining machine control circuits made it impossible to achieve a generic diagnostic system, but a generic approach for the synthesis of the diagnostic system was possible. As the research progressed, it became apparent that an algorithmic approach was better than an expert- system-based implementation. A prototype system was constructed and used to evaluate the diagnostic system. Prototype implementation issues are also examined.

Jan 1, 1993

By Thomas M. Barczak

State-of-the-art longwall roof supports provide effective strata control, but failures of these support systems still occur. To identify failure mechanisms and the impact these failures have on the safety of the support system, the U.S. Bureau of Mines has been conducting research on shield mechanics in the Bureau's unique mine roof simulator, as well as field studies of in situ support loading and investigations of longwall failures, Three types of failures are discussed: (1) inadequate support capacity, (2) structural failure, and (3) instability. Hypothetical situations with proposed courses of action and case studies of actual longwall failures are described. This information is intended to assist the Mine Safety and Health Administration (MSEIA) and industry mining personnel in safety evaluations of longwall roof support systems.

Jan 1, 1989

Geophysical Abstracts 1 - 86 were issued in mimeographed form by the Bureau of Mines; Abstracts 87 - 111 were published in bulletins of the Geological Survey; Abstracts 112 - 116 were issued in mimeographed form by the Bureau of Mines as Information Circulars 7256, 7257, 7267, 7273 and 7285. 1. GRAVITATIONAL METHODS 7380. Dryden, H. L. A reexamination of the Potsdam Absolute Determination of Gravity. Jour. Research Nat. Bureau of Standards, vol. 29, No. 5, 1942, pp. 303-314.

Jan 1, 1944

By R. Emmett Hughlett

The Bureau of Mines has developed a statistical approach to the laboratory evaluation of response bias and precision in gas detectors. The techniques described employ a computerized analysis and a new method of data presentation called composite graphing. The underlying theory, its practical application to the data, and the experimental equipment and procedure are described.

Jan 1, 1982

By C. E. Wood

A special appropriation made by Congress in July 1940 provided funds for the investigation of methods for recovering manganese from low-grade [ ] domestic deposits. These funds were assigned to the United States Department of the Interior, Bureau of Mines. A committee, identified as the Technologic Committee on Manganese of the National Research Council, National Academy of Sciences, was appointed to recommend the allocation of the funds for investigation of the more promising projects.

Jan 1, 1942

By C. E. Wood

A special appropriation made by Congress in July 1940 provided funds for the investigation of methods for recovering manganese from low-grade [ ] domestic deposits. These funds were assigned to the United States Department of the Interior, Bureau of Mines. A committee, identified as the Technologic Committee on manganese of the National Research Council, National Academy of Sciences, was appointed to recommend the allocation of the funds for investigation of the more promising projects.

Jan 1, 1942

By Lee Ann Gardner

This U.S. Bureau of Mines publication presents a case study of the processes used in permitting the Nome Offshore Placer Project, a gold mining project offshore Nome, Alaska which operated from 1985 through 1990. The mining project, developed by Western Gold Exploration and Mining Company, Limited Partnership (WestGold), used the BIMA, which was at the time the largest bucketline mining vessel in the world, to dredge gold from the ocean floor. This case study reviews the permitting process from the regulators' and industry's perspectives, as well as characterizing the efficiencies and inefficiencies associated with this case. The Federal, State and local laws applicable to the Nome Offshore Placer Project are identified, agency jurisdiction and interagency relationships are explored, and the chronology of the permitting process is examined. The regulatory authorities for both environmental monitoring and post-mining monitoring are delineated. Significant milestones affecting the project and required regulatory submittals are also included. The case study of the Nome Offshore Placer Project is detailed with respect to agency involvement and coordination, approaches to permitting from both the regulators' and developer's perspective, environmental issues, and permit stipulations which were unique to the project. The advantages and disadvantages of these topics are discussed.

Jan 1, 1992

By Thomas M. Barczak

The U.S. Bureau of Mines has been conducting research to optimize the design and utilization of mine roof support systems. An objective of these efforts is to evaluate the mechanical and structural responses of various mine roof support systems under simulated load conditions in the Bureau's mine roof simulator. Underground studies are also made to evaluate the in situ behavior of support structures. The purpose of this report is to document practical applications for longwall face and gate road supports that have resulted from these studies. This report is not intended to be an all-inclusive manual on every aspect of support utilization, but it does provide a comprehensive assessment of practical considerations relating to the mechanical and structural behavior of these support systems. Forty-six recommendations are made to provide assistance to mine operators in the testing, selection, and utilization of longwall face and gate road supports. Many of these recommendations offer innovative solutions to everyday problems faced by mining personnel in the control of ground in longwall mining.

Jan 1, 1989

By G. L. Oldright

The data presented in this paper were collected at the smelter of the Consolidated Mining & Smelting Co. of Canada, Ltd., Trail (Tadanac), British Columbia. Many thanks are due to S. G. Blaylock, vice president and general manager, James Buchanan, smelter superintendent, and George Murray, assistant smelter superintendent, for their broad general policy in permitting these data to be taken and published. life are also grateful for the help given by the staff members stated in Paper XI, Report of Investigations Acknowledgment is given several excerpts from experiments by F. E. Lee, head of the research staff. INTRODUCTION The past reputation of zinc as an ingredient in lead blast furnace slags has been bad. Zinc is thought of as a cause of accretions in the shaft of the blast furnace, of hot tops, of the formation of "zinc mush" in the crucible and forehearth, of lead-rich slags, of viscous slags, and. of low capacity in smelting.

Jan 1, 1934

By James Noll

Total carbon (TC) is sometimes used to measure or characterize diesel particulate matter (DPM) in occupational settings such as underground mines. DPM samples are collected on quartz fiber filters. When using quartz fiber ?lters, adsorption of gas phase organic carbon (OC) has been reported, causing a positive bias in the particulate TC results (adsorption artifact). Most of the data on the sampling artifacts and corrections apply to environmental air sampling, where samples are collected at a much higher filter face velocity and the OC concentrations are generally much lower relative to occupational sampling. In this study, we investigated the effects of adsorption artifact on samples from occupational settings. Samples were collected with and without denuders to determine the amount of gas phase OC collected and the accuracy of certain corrections. In underground stone mines, the adsorption artifact was found to positively bias the particulate TC by greater than 20% for filter loadings below 25 µg/cm2 TC (8-h time weighted average) 262 µg/m3). The tandem ?lter correction reduced the effect of the artifact, as high as 60% of the TC value, to less than 11% for laboratory data. It also significantly reduced the effect of the artifact obtained for field samples.

Jan 1, 2008

By D. Bienstock

As part of the development of the hot-carbonate scrubbing process by the Bureau of Mines, the corrosion rates of steel in boiling solutions of potassium carbonate saturated with carbon dioxide and hydrogen sulfide were determined, and the effectiveness of various inhibitors was evaluated by Bureau researchers. The highly corrosive solution of carbonate saturated with carbon dioxide can be inhibited with a 0.2-percent concentration of either potassium chromate or sodium metavanadate. Solutions of carbonate saturated with carbon dioxide and hydrogen sulfide are mildly corrosive, 0.01 inch per year. Complete absence of corrosion is obtained with 0.2 percent sodium metavanadate or 0.15 percent vanadium pentoxide. Oxidizing inhibitors such as potassium chromate are destroyed in the alkaline sulfide mixture, N-alkyl trimethylene diamines, at a concentration of 0.1 percent, lower the corrosion rate to about 0.005. Sodium metasilicate, at a concentration of 0.6 percent, completely inhibits the corrosion but may deposit free silica in the system. Commercial cladding materials such as the epoxy coatings also prevent corrosion.

Jan 1, 1962