Search Documents

Viscosity measurement was carried out over a narrow range of silica content around the fayalite composition. A wide range of temperature and oxygen potential was covered where the slag was completely liquid. In order to keep the slag composition and the Fe3+/Fe2+ratio constant, theCO2/CO ratio was kept constant as the temperature was varied. Increasing the Fe3+content has little effect on viscosity for slags with a silica mole fraction of 0.31. At higher silica contents, increasing the Fe3+content brings about a small decrease in the viscosity.

Jan 1, 2004

By C. S. Kucukkargoz, A. Bhalla

"The solid-state reduction of ilmenite concentrate with graphite was studied under argon atmosphere at temperatures between 1050°C and 1350°C. The rate of reduction increased with increasing temperature and decreasing particle size, with the maximum extent of reduction found to be 80% at 1350oC with a particle size in the range of -106 +90 µm. The activation energy for the reduction reaction was calculated to be 257 kJ/mole. The trivalent iron oxide was reduced first to divalent iron oxide and then to metallic iron. An annular ring of a partially reduced oxide phase containing metallic nuclei was formed around the core of ilmenite, which grew in size as the original ilmenite core shrank with progressive reduction. The reduction of titanium dioxide also took place during this stage, which produced the Magneli oxides in the form of TinO2n-1. The metallic phase had very high Fe and low Ti contents throughout the reduction, whereas the partially reduced oxide phase adjacent to the metallic phase was high in Ti and depleted in Fe. The metallic phase globules formed during this stage were small and are considered suitable only for leaching and not for other concentration processes. The core of the particle generally retained the composition of the original ilmenite. The purpose of this work was to remove iron and increase the titanium oxide content of the ilmenite to produce a high-titanium containing charge for subsequent smelting.IntroductionThe titanium-bearing minerals ilmenite (FeTiO3) and rutile (TiO2) are the primary natural raw materials used in industry to produce titanium metal and titanium-based products. The common titanium-bearing minerals are ilmenite, rutile, anatase, brookite, leucoxene, arizonite, and perovskite. Although the formula of ilmenite is commonly expressed as FeTiO3, the mineral can accommodate Mn and Mg, which are chemically bound in the form of (Fe,Mn,Mg)TiO3. Ilmenite concentrate can also contain Fe2O3 and Al2O3 in addition to the physically separable oxides such as SiO2 and CaO. The crystal structure of ilmenite is an ordered derivative of the corundum structure with a trigonal-rhombohedral symmetry. Fe2+ and Ti4+ ions occupy the octahedral sites, leaving the tetrahedral sites unoccupied. In each FeTiO3 unit, there are three O2- ions creating three octahedral sites, two of which are occupied by Fe2+ and Ti4+ (Wilson et al., 2005)."

Jan 1, 2017

By P J. Grobler

The current commodity boom is depleting the ore bodies at a rate not seen in the past. As the existing ore bodies get depleted, only the more inferior bodies are left for exploitation. This places an emphasis on beneficiation to upgrade the lower grade ore to high-grade feedstock for downstream processes. This paper discusses the role of dense medium separation in this quest for high-grade feedstock for the future. It covers the production and utilization of ferrosilicon and gives a future perspective of the technology. It concludes about the way ahead and the challenges facing the processing fraternity and mining industry.

Jan 1, 2006

By A.M. Edwards

1. Book reviews Platinum in South Africa, compiled by A.M. Edwards and M.H. Silk. Randburg, Council for Mineral Technology (Private Bag X3015, Randburg, 2125 South Africa), 1987. 55 pp. U$30. Reviewer: R.D. Wintle Scientific and technological developments in extractive metalurgy-G.K. Wiliams Memorial Volume. Parkvile (Australia), The Australasian Institute of Mining and Metalurgy, 1986. $A12 (incl. surface postage). Reviewer: T.Y. OweD Ion exchange and sorption processes in hydrometa/urgy, edited by M. Streat and D. Naden. Chichester, John Wiley & Sons, 1987. 229 pp. Reviewer: B.R. Green Role of Government in mineral resources development, edited by Michael J. J ones. London, The Institution of Mining and Metalurgy, 1985. 180 pp. £40. Reviewer: K.E. Ducat 2. Recent publications Annual report 1987. International Tin Research Institute, Kingston Lane, Oxbridge, Middlesex UB8 3PJ, England, 1988.Tin and its uses no. 156. Address as above. 3. Mintek reports Application Report no. 5 The production of and alusite and other refractory minerals. 1988. 16 pp. . Application Report no. 6 The development up to commercial application of a process for the recovery of lead, copper, zinc, and silver from the Black Mountain deposit. 1988. 14 pp.

Jan 1, 1988

Book review HOEK, E., and BRAY, J. Rockslope engineering. London, The Institution of Mining and Metallurgy, 1974. £5. NIM reports Report no. 1625 The determination of uranium and thorium by the use of delayed neutrons. Report no. 1626 Formation constants of zinc chlorocomplexes in perchlorate medium. Report no. 1629 The thermodynamics of the formation of complexes of silver with some substituted pyridines. Report no. 1630 An electrochemical investigation of the dissolution of copper, nickel, and copper-nickel alloys in ammonium carbonate solutions. Report no. 1640 A semi-automatic titrimeter for cyanide analyses. Report no. 1644 Prospects for the recovery of minerals from the sea. 1974 A.S. & T.S. National Award Professor D. C. Midgley, President of the Associated Scientific and Technical Societies of South Africa, today announced the winner of the 1974 A.S. & T.S. National Award. 1974 G.W. en T.V. Nasionale Toekenning Professor D. C. Midgley, President van die Geassosieerde Wetenskaplike en Tegniese Verenigings van Suid- Afrika het vandag die wenner van die 1974 G.W. & T.V. Nasionale Toekenning aangekondig.

Jan 9, 1974

By E. Matinde

Human beings have been dependent on metals and alloys for livelihoods since time immemorial. In fact, there is irrefutable evidence that successful ancient civilizations achieved supremacy over their environments through the mastery of metals and alloys (Miller, 1995; Mtetwa, 2022). Over time, metals and alloys have evolved to become ubiquitous engineering materials indispensable to mankind, with applications in industrial and residential infrastructure, agriculture, energy generation and storage, transportation and communication systems, and manufacturing, among others (Elshkaki et al., 2018; Watari et al., 2021). Population growth, technological developments, and increase in urbanization and industrialization are all intricately linked to the intensity of use of metals and alloys. With up to 5 billion people estimated to live in urban areas by 2030 (Armstrong, 2009), the demand for metals and alloys will inevitably increase in order to satisfy the increased demand for infrastructure, machinery, and other human needs (Elshkaki et al., 2018; Watari et al., 2021). According to LePan (2022), urbanization and growth of mega-cities will increase the demand for metals and alloys, such as nickel, steel, aluminium, and copper by 116%, 50%, 57%, and 26%, respectively, between 2019 and 2035. Naturally, the production of metals and alloys from natural ores, secondary resources, and/or a combination of both, to meet this increased demand will invariably lead to the increase in generation of deleterious emissions in the form of wastes. In fact, mining and metallurgical wastes currently constitute the world’s largest anthropogenic streams by mass, often containing a high concentration of elements and compounds that can cause potential damage to natural ecosystems and humans (Hudson-Edwards et al., 2011; Lottermoser, 2011; Matinde et al., 2018; Seetharaman et al., 2022). Obviously, society’s heavy reliance on new mineral resources to drive the emerging energy transition entails that the legacy of these waste streams will continue unabated for the near-foreseeable future. The scarcity of high-grade mineral reserves, coupled with deliberate efforts to solve the anthropogenic circularity conundrum, therefore introduces a high level of urgency in the metal extraction industry to develop nascent and more eco-friendly processes and technologies. Integrating circular economy principles based on intentional configurations of circular industrial ecosystems in order to maintain the value of materials and resources in the economy for as long as possible is widely accepted as a practical approach to mitigating the negative externalities imposed by

Sep 1, 2024

By M. Ndabeni, J. H. van Vreden, M. Le Roux, Q. P. Campbell

It is not uncommon for gold slurry ponds or screen oversize dumps to contain several different types of carbon-rich contaminants. These contaminants act as robbers of dissolved gold which has a detrimental effect during the downstream carbon-in-leach (CIL) or carbon-in-pulp (CIP) processes. With a renewed interest in the reprocessing of contaminated gold waste ponds and dumps, preconcentration of the feed to either the CIL or CIP process becomes important to maximise profits from these resources. An added advantage in removing these resources, which were once thought of as being uneconomical, is the availability of land that can further be rehabilitated for community development projects. For gravity separation, an example of suitable technology is the Reflux Classifier (RC), which can be used for the separation of materials of different densities and can be used as a pre-concentration step. In this project, a laboratory-scale Reflux Classifier was used to pre-concentrate a gold-bearing sample obtained from a waste dump situated to the east of Johannesburg, South Africa. The material had an average gold grade of 1.9 g/ton and a carbon content of 10%. This material was first fed to a semi-batch Reflux Classifier that was used to fractionate it into several different density intervals by varying the fluidisation water feed rate, followed by continuous runs at fixed water flow rates. The results showed that a cumulative gold recovery of 60%, carbon recovery of 85%, and mass pull of 41% was possible for a fluidisation water feed rate of 15 L/min, while a rate of 20 L/min resulted in a gold recovery, carbon recovery and mass pull of 83%, 92% and 79% respectively, which translated into a concentrate gold grade above the set target of 3 g/ton. Continuous operation at 20 L/min yielded an underflow stream with 84% gold recovery at a grade of 5.4 g/ton. Keywords: Reflux Classification, gold recovery

Jan 1, 2020

By V. W. Lumadi, S. Nyasha

The mining industry has yet to fully accept and embrace the strategic role of technology and innovation in successful business planning and execution. In this study, we empirically determine the factors that influence acceptance of technology solutions in the mining industry in South Africa, assess critical success factors influencing adoption of advanced technology in the South African mining industry, and explore challenges faced by the mining industry in South Africa in adopting advanced technology in its operations. Thematic content analysis is employed in the data analysis. Results show that critical success factors to the adoption of mining technology include learning culture, knowledge sharing, high labour costs, and behaviour of other firms in the industry; commonly identified challenges include inadequate engagement with external stakeholders, uncertainties, the cyclical nature of the sector, and high risk related to the adoption of unproven technology and performance systems focused on volumetric production. The study encourages mining companies to implement usage of technology. This can be properly done through regular engagement with the Minerals Council South Africa.

Apr 14, 2024

By A. Becker, R. Tait, S. L. George, A. Carlisle

Surface treatments like laser shock peening (LSP) induce residual stresses penetrating up to 1 mm deep, surpassing traditional methods, thus significantly increasing the potential impact on materials prevalent in the automotive and aerospace sectors. Through extensive fatigue testing and fractography investigations, it was determined that LSP resulted in a fatigue life increase of over five times for aluminium alloy AA7075-T6 and titanium Ti-6Al-4V. Increased fatigue life was also noted in AISI316 stainless steel, which showed increases in fatigue life of 1.7x. While fatigue life in all cases improved, the efficacy of LSP was shown to be material dependent.

Jul 23, 2025

By R. Uwaoma, A. Goosen, R. Matjie, K. Mphahlele, J. Bunt

Coal properties that are associated with wear and damage of grinding equipment during pulverization prior to combustion were investigated. A South African Highveld feed coal and its beneficiated fractions were crushed to <1 >0.25 mm particles for the grindability tests. These particles were milled and screened into <75 μm and >75 μm fractions, which were analysed by different techniques to establish a correlation with the conventional Hardgrove Grindability Index (HGI). The <1.5 g.cm-3 float fraction, which contained 93 vol.% (mineral matter free) total -macerals,9% kaolinite, and had the lowest HGI (57) (hardest to grind) was pulverized for 15, 30, 60, and 120 minutes for particle size distribution analysis. This analysis indicated that the content of <75 μm particles increases with increased grinding time. The >1.9 g.cm-3 sink fraction, with the highest HGI (76), 44% kaolinite, and 20 vol.% total macerals, was ground easily to generate the highest proportion of <75 μm particles. Based on higher correlation coefficients (R2 = 0.77–0.91), the ash yield, mineral matter, petrographic composition, and fixed-carbon have significant effects on the HGI. Conversely, the inherent moisture and total sulphur (R2 = 0.48–0.62) have only minor effects on the HGI. Results from this investigation could be implemented in the preparation of a suitable pulverized fuel with little equipment wear, as well as utilizing mineralogical and petrographic compositions. Finally, the effect of microlithotypes and maceral types in South African feed coals on the HGI should be investigated in further pulverization and grindability studies.

Jul 5, 2023

By T. Phiri, Antoine Floribert Mulaba-Bafubiandi

Microwave energy has been recently used in minerals processing to speed up the leaching process or to improve the liberation of targeted minerals (Al-Harahshed and Kingman, (2003); Bradshaw et al., (2001)). Applied to the roasting of sulphide minerals, microwaves allow the ?tunning? of calcine types and products quality in addition to the energy savings as opposed to the conventional roasting (Mulaba, 2006). As more than 85% of world zinc is produced through the ?roast-leach-electrowin? route, an attempt was made to optimize cost, energy and product quality for metal extraction process route. The use of microwaves was the alternative process route selected for the optimisation. Pyrite concentrate (0.17% Zn, 0.09% Cu, 35.71% Fe, 43.76% S) and sphalerite concentrate containing 43.81% Zn, 0.37% Cu, 3.86% Fe and 44.39% S were microwave roasted in a multimode cavity of 2.45 GHz with varying power levels and for different durations. The produced calcines were characterized using AAS, XRF, XRD and Mossbauer spectroscopy while the determination of residual Sulphur was used as products quality control tool to ascertain the degree of roasting achieved on the feed. The leachability of the produced calcines in HCl, HNO3, H2SO4 and HNO3 + HCl has been studied in terms of the best leaching yield, process kinetics economics and environmental aspect. With 800 W power for 30 minutes, ZnO and Fe2O3 were formed corresponding to a 70% sulfur removed from sphalerite and 80% from pyrite concentrates respectively. While the roasting of the above concentrates appeared to be a first degree processes, it was noticed that the microwave assisted roasting of sphalerite and pyrite concentrates yielded lower sample surface temperature for a shorter time (i.e.less than 30 minutes) microwave exposition. Longer time (more than 30 minutes) microwave exposure showed a linear increase in temperature in function of power level used. While optimum roasting conditions were found at 800W, 30 minutes, a 10% increase of sulfur removal was noticed while pyrite concentrate was microwave roasted. Sulfuric acid was seen to give higher leaching yield than nitric acid. Zinc dissolution was hindered by the presence of franklinite.

Jan 1, 2007

Contribution by G. Narsimhan It was with much pleasure that I went through D.F. Malan&apos;s excellent paper. The following explanatory and critical note has been the result of my deep study of the paper. Although by qualifications and experience I have been a chemical engineer, involved over four decades with problems in the modeling and simulation of transport-limited (heat and mass) chemical reactions in multi-phase systems, I have of and on interested myself in challenging problems in extractive metallurgy. This is the first time I have veered of to continuum mechanics, at the age of 71! Author&apos;s reply. I thank Professor Narsimhan for his extensive contribution to the paper. It provided me with the stimulus to derive an extended model. However, there are some inaccuracies in his arguments that need further discussion. Professor Narsimhan&apos;s main concern is that there is not a good enough fit between the derived viscoelastic Kelvin model and the experimental data supplied by Güler1 (see Figure l1 on page 218 of my paper). I will therefore explain the choice of a viscoelastic model in more detail and also make specific comments on the arguments given in his contribution.

Jan 1, 1996

By R. Lechuti-Tlhalerwa

"Geometallurgy aims to improve mining project value by predicting the impact that ore and waste characteristics will have on mining and metallurgical processes. This requires integration of rich spatial models of orebody characteristics with validated process response models. These models have, until recently, been constrained by the spatial coverage and representativity of relevant data and the ability to validate predictions made.The revolution in the diversity and volume of data and computational power that is now becoming available for integrated geoscientific modelling of orebodies, and stochastic simulation of mining and mineral processes is accelerating. By embracing emergent integrated data analysis and simulation techniques, geoscientists and engineers can lead a transformation in the way the mining value chain, from orebody to recovery, can be conceived, evaluated, and operated by using the geometallurgical paradigm.This paper describes a methodology that is applied to an existing diamond operation. Analysis of spatial and process data is used to build an integrated geometallurgical value chain model (IGVCM). This IGVCM is used to generate geometallurgical options and evaluate their potential outcomes. The model facilitates the use of flexible, highly configurable, and potentially automated intelligent approaches to evaluate mining and mineral process configuration, and results in more robust design outcomes. The approach described here, and its successful implementation has potential to deliver step-changes in value. IntroductionGeometallurgy aims to identify treatability risks – and opportunities – that arise from the interaction of orebody characteristics with mining and treatment. Improved understanding of the rock/process relationships allows project planners and production teams to predict performance, identify potential shortfalls, and thus enable the proactive creation and evaluation of strategies to mitigate these risks. These advanced insights also create opportunities for continually improving operational performance through dynamically adapting and improving the process response to the changing properties of the ore (Figure 1)."

Apr 1, 2019

By Dave Deglon, Andrévan der Westhuizen

Objectives ?Survey typical Met Accounting streams at the Zincor refinery ?Determine Precision in Metal Conc?s Measurements for Monthly Met Balance ?Determine the Components of Variance in these Met Acc Values (Sampling, Preparation, Analyses) ??Common plant practice? should be mirrored even though not always in perfect agreement with ?laid down procedures? or ?good practice? ?Mass Measurement and Inventory Measurement was considered in less detail ?not reported here

Jan 1, 2005

By O. S. L. Bruinsma, M. J. Matsela, D. J. van der Westhuizen

The free ligand (FL) model is an intuitive model to calculate the equilibrium concentrations in solvent extraction (SX) based on the distribution coefficient (Kd) at infinite dilution and the fraction of free ligand available for extraction. In this work, the FL model is validated to account for co-extraction of Ni and for designing the extraction and scrubbing sections of Co/Ni separation in a base metal refinery. Cyanex 272 is employed as a selective Co extractant in the process to yield high purity Ni. To enhance the loading capacity of the extractant, 50 mol% of NaOH is pre-loaded into it. Experimental and FL modelling results show that four equilibrium stages are required to purify the 99% Ni feed to a 99.97% Ni raffinate. The 53.59% co-extract with 26.76% free ligand is purified with a reflux scrub of 30 g Co/L in one equilibrium stage to 99.01%, Co in the scrubbed extract. The FL model as well as the Co/Ni/Na-analysis of the aqueous phase confirm that in the scrubbing section, Ni in the extract is mainly replaced by Co. Finally, in the one stage stripper the Co concentration in the scrubbed extract is increased from 5.6 g Co/L in the extract to 30.5 g Co/L that is partially used as reflux scrub liquor.

Dec 11, 2024

By M. Reuter, C. Schuffeneger, T. Seppälä, L. Holappa

Reaction kinetics of solid-state reduction of chromite pellets (laboratory made and industrial) and lumpy ore was investigated by the thermogravimetric analysis (TGA) technique. Carbon monoxide was used as the reducing agent, with the presence of graphite in proximity to chromite. The experiments were carried out at both rising temperature and constant temperature in the range of 1450 - 1550°C. Scanning electron microscopy was employed to observe and analyse the structure and composition changes of the chromite samples. For the lab-made chromite pellets, the effects of particle size and bentonite addition on the reduction behaviour were studied. The pellet with smaller particle size gave a higher reduction rate. Bentonite addition had slightly negative effect on the reduction rate. When reducing industrial pellets, temperature and CO flow rate had positive influence on the reduction rate. Reduction of lumpy ore took place slower than reduction of a pellet. In all samples, chromite reduction proceeded longer in the outer part of the sample than in the centre part. The porosity of the chromite samples was determined before and after the experiments. The porosity of lumpy chromite increased significantly during the reduction. However, the porosity of lab-made chromite pellet decreases due to sintering effect. The reaction mechanism is discussed on the basis of experimental results and earlier investigations.

Jan 1, 2004

2nd CONGRESS OF THE INTERNATIONAL SOCIETY FOR ROCK MECHANICS The 2nd Congress of the International Society for Rock Mechanics will be held in Belgrade, 21-26 September, 1970. The Congress will include: working sessions, study tours, receptions, excursions introduced in the working sessions and post-congress excursions and special programme for accompanying persons. Anyone interested in rock mechanics and its applicarion may take part in the 2nd Congress. Official languages of the Congress are: English, French and German. Simultaneous translation service will be provided during the Congress. All the correspondence concerning the 2nd Congress of the International Society for Rock Mechanics should be addressed to: Sekretarijat 2. kongresa Medjunarodnog drustva za mehaniku stena Institut za vodoprivredu "Jaroslav Cerni" Bulevar vojvode Misica 43, Postanski fah 530 Beograd - Jugoslavija NINTH INTERNATIONAL SYMPOSIUM TECHNIQUES FOR DECISION MAKING IN THE MINERAL INDUSTRY The Symposium which is to be held in Montreal during the week of June 14-19, 1970, follows the Computer Symposium held in Salt Lake City this year. The purpose of the Symposium is to define the role of decision making techniques within the mineral industry and to stimulate the development of specific applications. The subject of the Symposium-mathematics, operations research and computers as applied to the mineral industry-allows a complete picture of the mineral industry in its public policy, corporate, financial and technological environment to emerge. This is another of the series of symposia on this and related subjects started in the early 1960&apos;s at the University of Arizona. Sponsorship has included a number of Universities and the Society of Mining Engineers of the American Institute of Mining. This 1970 symposium is the first to be held outside of America, and is being sponsored by the Canadian Institute of Mining, McGill University and Ecole Polytechnique. A number of delegates from South Africa have participated in these symposia and several have already arranged to attend this symposium in Montreal. Enquiries should be directed to: Secretariat, The 9th International Symposium, Department of Mining Engineering, Ecole Polytechnique, P.O. Box 50l, Snowden, Montreal 248, Quebec, Canada. 24th INTERNATIONAL GEOLOGICAL CONGRESS This Congress is to be held in Montreal, Canada, from August 21 to 30, 1972. A very detailed and extensive programme has been proposed, and includes a number of excursions. Copies of the first circular are obtainable from: The Organizing Committee, 24th International Geological Congress, 601 Booth Street, Ottawa 4, Ontario, CANADA. SYMPOSIUM ON THE RECOVERY OF PYRITE The proceedings of the Symposium on the Recovery of Pyrite, held in Johannesburg on 12th to 13th June 1969 are now available. Copies may be ordered from the Secretary, S.A.I.M.M., P.O. Box 61019, Marshalltown, Transvaal at a cost of R10.00. Papers and addresses presented at the Symposium were: Opening Address by Mr J. K. E. Douglas (President). &apos;The world sulphur position,&apos; by W. C. J. van Rensburg (Member). &apos;The South African sulphur position,&apos; by D. L. Taylor (Member). &apos;The recovery of pyrite at Government Gold Mining Areas Limited,&apos; by R. J. Westwood (Member), G. S. Stander (Affiliate) and H. R. Carlisle (Member). &apos;Recovery of pyrite concentrates from colliery-waste discards-A preliminary assessment,&apos; by W. A. Gilbert (Visitor) and E. A. Nugent (Member). &apos;The role of pyrite in upgrading the uranium content of Witwatersrand conglomerate ores by means of the heavy-medium separation process,&apos; by D. J. Tutt (Associate Member). &apos;Pyrite recovery by jigs at Durban Roodepoort Deep Limited,&apos; by E. J. Dominy (Affiliate), F. Diamond (Affiliate) and A. D. Graham (Affiliate). &apos;The storage of pyrite concentrates,&apos; by Joan C. Campkin (Visitor) and P. J. Lloyd (Member). &apos;The flotation plants of the Anglo- Transvaal Group,&apos; by L. A. Bushell (Member). &apos;Pyrite flotation with amines and cyanidation of the products,&apos; by E. H. D. Carman (Member). &apos;Gold recovery by cyanidation from mill products obtained after pyrite flotation,&apos; by P. G. Mrkusic (Graduate), M. Sciarone (Visitor) and H. E. Simonsen (Visitor). &apos;The influence of sulphydral and cationic flotation reagents on cyanidation of native gold,&apos; by K. G. Ashurst (Visitor) and W. P. Finkelstein (Member). &apos;Laboratory tests on the flotation of pyrite from Witwatersrand gold ores by cationic collector,&apos; by J. Levin (Member), and M. L. Veitch (Visitor). Closing Address, by Dr R. E. Robinson (Director, National Institute for Metallurgy).

Bateman Engineering managed the establishment of a second diamond treatment plant at the Letseng Mine in the Mokhotlong District of northern Lesotho, about 100 km from the town of Buthe Buthe. Letseng Diamonds Proprietary Limited, is owned 70 % by Gem Diamonds and 30 % by the Government of the Kingdom of Lesotho. The second plant, which commenced construction in late 2006, doubled Letseng Mines&apos; hard rock processing capacity from 2.6 million t/yr to 5.2 million t/yr, making it the worlds&apos; seventh largest diamond mine by throughput. Bateman Engineering provided the engineering design, procurement and construction management of the new plant.

Jan 1, 2010

By R. Abela

In over ninety per cent of mineral sand plants, the most commonly used equipment is the spiral concentrator. The tonnage treated over typical spiral plants can range from as low as 200 ton per hour up to 6 000 tons per hour. Due to the limited capacity of each spiral, plants consist of multiple spirals assembled into banks. The mixture of minerals present in the sand feed requires several spiral stages to achieve the desired mineral recovery. Due to the complexity of the spiral circuits, there are always some design and operating problems that present themselves in plants. These range from slurry distribution, spirals operating at incorrect design parameters and feed variations. The material being treated is difficult to maintain in suspension due to its high density, resulting in segregation and preferential flow in pipelines, distributors and sumps. The objective of this paper is to highlight common problems associated with spiral installations to designers and operators of plants. Practical solutions are recommended in order to prevent and minimize these mistakes in the design. These solutions may be used to improve performance on operating plants.

Jan 1, 2003

By D. Nag, J. Fernando

Hazelwood Power Mine is one of the largest open pit brown coal mines in Australia. The removal of overburden is the first step in coal winning operation. The primary aim of construction of overburden dump is to provide an effective stable working surface for stacker. The paper discusses site investigation techniques used to determine dump soil properties, stability analysis method using GALENA and GWEDGEM, results of stability analysis. The paper concludes with recommendation for a safe dumping strategy for level 2 stacker dumping.

Jan 1, 2003