Search Documents

An effective electrowinning process in hydrometallurgical industry requires fluoride levels in the base metal solution to be less than 10 mg/l. Selective removal of the fluoride ions from base solution is thus desired, if fluoride was added to control calcium and magnesium in the circuit. Consequently, adsorption of fluoride onto activated alumina was studied in a batch and a column set-up. The effects of base metal solution pH, temperature, initial concentration and flow rate on activated alumina performance were investigated in either a batch or column configuration. A two-level factorial experimental design was implemented in studying column dynamics. Results demonstrate that activated alumina is an effective adsorbent for selective removal of fluoride from base solution. In the batch operation, fluoride was removed to values below the maximum allowable concentration (10 mg/[l]) when pH was = 8. In the column adsorption step at 55°C and 600mg/[l] initial concentration, up to 16 bed volumes were processed before breakthrough level was reached. Desorption step using 1% sodium hydroxide solution achieved an elution of 8 bed volumes. The activated alumina (AA) had a capacity of 8.65 gF/[l]AA at the 10mgF/[l] fluoride breakthrough level during the column adsorption test. Keywords: Fluoride; activated alumina; adsorption; recovery; regeneration.

Jan 1, 2009

By K. Schwerdtfeger

Data are presented on the effect of iron oxide on the electrical conductivity of CaO-SiO2-FeO-Fe2O3melts, and on limiting current and impedance in direct current or alternating current charge transfer at iron electrodes. The strong influence of iron oxide content can be utilized for in situ determination of total iron oxide content and Fe3+/Fe2+ratio. The possible probe designs are presented and the principles and procedures of the measurements are explained. Keywords: in situ probe for iron oxide determination in steelmaking slags, electrical conductivity of CaO-SiO2-FeO-Fe2O3slags, direct current over voltage and alternating current impedance at iron/slag electrodes.

Jan 1, 2004

By J. C. Taylor

The Rhodax inertial cone grinder, designed by France?s FCB Group Fives, is the result of three years, theoretical and mechanical research in the field of compression grinding by the research staff of FCB?s CRM minerals research centre. A number of potential uses have been assessed and will be discussed in the paper. The crusher is an inertial grinder that works on the pressurized bed fragmentation principle. The fragmentation force is caused by the rotation of unbalanced masses rather than by an eccentric mass, as is the case in a conventional crusher. This makes it possible to achieve very high reduction ratios. By controlling the speed of rotation of the unbalanced masses, the grinding force can be modified, thus changing the product size distribution. The paper describes the machine layout, operating principles, control parameters and will briefly describe the results obtained on reef, waste and ROM reject pebbles. Some comparisons are made with conventional crushing.

Jan 1, 1998

By F. Agterberg

In his 1978 monograph ‘Lognormal-de Wijsian Geostatistics for Ore Evaluation’, Professor Danie Krige emphasized the scale-independence of gold and uranium determinations in the Witwatersrand goldfields. It was later established in nonlinear process theory that the original model of de Wijs used by Krige was the earliest example of a multifractal generated by a multiplicative cascade process. Its end product is an assemblage of chemical element concentration values for blocks that are both lognormally distributed and spatially correlated. Variants of de Wijsian geostatistics had already been used by Professor Georges Matheron to explain Krige’s original formula for the relationship between the block variances as well as permanence of frequency distributions for element concentration in blocks of different sizes. Further extensions of this basic approach are concerned with modelling the three-parameter lognormal distribution, the ‘sampling error’, as well as the ‘nugget effect’ and ‘range’ in variogram modelling. This paper is mainly a review of recent multifractal theory, which throws new light on the original findings by Professor Krige on self-similarity of gold and uranium patterns at different scales for blocks of ore by (a) generalizing the original model of de Wijs to account for random cuts; (b) using an accelerated dispersion model to explain the appearance of a third parameter in the lognormal distribution of Witwatersrand gold determinations; and (c) considering that Krige’s sampling error is caused by shape differences between single ore sections and reef areas.

Jan 1, 2015

By Henk van der Bijl, Sean Rogers, Eugene Sidorski, Alan Carpenter

The electrode column is the heart of the submerged arc furnace. Superior electrode performance provides improved furnace performance. This paper describes the main features of the electrode column that delivers superior performance in furnaces worldwide, developed by Pyromet. Pyromet?s electrode comprises the compact slipping device, lower electrode assembly, upper and lower mantles, self-adjusting electrode seal, paste heaters, and Pyromet?s patented innovative electrode breakage detection and length determination system. Pyromet?s slipping device features compact interlocking clamping rings, incorporating fail-safe spring-loaded design. The interlocked clamping rings distribute the clamping force over a larger area of the electrode casing, preventing damage. The slipping device assembly features a low maintenance modular design that allows rapid slipping cycle times, back slipping, and compatibility with Pyromet?s electrode breakage detection and length determination system. Pyromet?s lower electrode assembly consists of the contact shoes, pressure bellows, pressure ring and heat shields. The contact shoes and pressure ring are designed for long, trouble free operation whilst the pressure bellow configuration equalise contact pressure and current distribution. Furthermore, the contact shoes incorporate a self cleaning feature, ensuring optimum electrical contact. The segmented design offers easy maintenance. Pyromet?s clients experience less down time due to longer component life. Pyromet?s remote adjusted electrode seal assembly reduces the rope seal working temperature, increasing rope life. The self compensating rope seal clamping force ensures an effective seal as the rope wears. Pyromet?s electrode breakage detection and length determination system detects electrode breaks utilising Pyromet?s electrode holder and data processing system. The length measurement system controls electrode length, eliminating the occurrence of short electrodes. The length measurement system furthermore eliminates the need for manual electrode length measurement, reducing associated production losses during furnace burn downs.

Jan 1, 2007

The April General Meeting of the Institute was held in Kelvin House, Johannesburg, on 16th April, 1969, at 4.30 p.m. Mr R. C. J. Goode (president) was in the Chair. There were also present nineteen Members, including Messrs R. J. Adamson, F. P. Bath, J. K. E. Douglas, A. R. C. Fowler, P. Lambooy, D. G. Maxwell and J. A. Nixon, (Council Members), Messrs E. L. Atkinson, I. R. Chaston, J. L. Edwards, J. S. Hall, S. A. Hancox, A. F. Lee, W. K. B. Loftus, H. S. Simpson, A. N. Shand, R. A. Wilson, H. J. Wright and J. E. Van Leeuwen. Nine Associate Members, including Messrs O. Davel, G. Douglas, P. R. Garcia, D. J. Murphy, D. Rankin, G. Schwartz, H. N. Singer, S. Thompson and D. A. Viljoen. One Graduate Mr D. Bosley. Ten Visitors, including Messrs S. Adler, C. E. Alvey, B. J. Botha, K. Chant, L. W. Davis, R. N. Guest, R. V. Keet, E. G. Keown, M. D. Lourie and S. McMurray. Secretary Mr D. C. Visser. Total present: Fourty-one. MINUTES The President requested that confirmation of the minutes of the previous meeting be held over as they would only be appearing in the Journal of the following month. Agreed. MEMBERSHIP The President: "I have much pleasure in announcing that the names of the under-mentioned candidates, having been published in accordance with By-law 5.2.2, Council has elected them to membership of the Institute in the following grades: Members: Kenneth Sinc1air Rae, Ian Robert Malcolm Chaston. Associate Members: Norman Isaac Thomas, Ian Connell Robinson. Graduates: Simon Richard Jeremy Perkins, Bleddyn Reginald Lear, David Williams. Affiliate: Richard Robert Will. Students: Angus David McElwee, Clive Renard Archer, Peter Andrew Locke. MEMBER TRANSFERRED TO A HIGHER GRADE From Graduate to Associate Member: Patrick James Burns. I welcome the newly elected members to the Institute and congratulate the member who has been transferred to a higher grade." (Applause). GENERAL BUSINESS The President reminded members that a buffet supper at a cost of 55c would be available after the meeting. PAPER FOR PRESENTATION The President noted with pleasure that a strong contingent from De Beers and the Finsch Mine were present. He expressed gratitude to Mr Loftus for coming

By N. Hanief

This research involves the investigation of phase transformations in the platinum-chromium coated system. Single-layer 0.1 µm platinum coatings were deposited via electron beam deposition on 99.98 percent pure chromium substrates. Specimens were subjected to systematic heat treatment in a vacuum furnace at 900°C for up to 20 hours. Phase formation and the changes in surface morphology were investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM).Both CrPt and Cr3Pt phases are formed during heat treatment for different times at 900°C. Significant changes in the morphology of this coated system were detected after heat treatment at 900°C for 20 hours.

Jan 1, 2012

By Van Sint JanM., M. Prudencio

ABSTRACT We report the results of a model-testing program to evaluate the strength characteristics of non-persistent joints. We describe the conditions under which new tensile cracks generate and propagate to connect existing joints so that the rock mass becomes fractured into several blocks, leading to a low strength. The strength of some models was equal to that along a single joint through the full sample length. In models with two joint sets, failure took place along a composite plane, partly sliding along a discontinuous joint and shearing through the intervening intact block of rock, or else by rotation and sliding of the blocks. This last failure mode could also lead to very low model strength. ZUSAMMENFASSUNG Dieser Bericht beschreibt die Ergebnisse von Versuchen mit Modellfelsmassen um den Einfluâ von unterbrochenen Rissen in ihrer Widerstandsfähigkeit zu untersuchen. Es werden die Umstände beschrieben unter denen neue Zugrisse entstehen, sich verbreiten, sich mit bestehenden Rissen verbinden und die Felsmasse in mehrere Felsblöcke zerlegen und zu einer kleinen Widerstandsfestigkeit führen. Der Widerstand einiger Versuchskörper entsprach der Festigkeit eines Risses der die ganze Länge des Versuchskörpers überquert.Versuchkörper mit zwei Rißfamilien versagten unter einer zusammegesetzten Ebene, zum Teil mit Verschiebungen nach unterbrochenen Rißebenen die sich durch Schnittversagen intakter Felsblöcke verbinden, und zum Teil durch Drehungen und Verschiebungen einzelner Felsblöcke. Die letzte Versagunsart kann zu einer stark verminderten Widerstansfähigkeit führen. RÉSUMÉ Nous présentons les résultats de quelques essais fait sur des modèles évaluant les caractéristiques de résistance des fractures discontinues. Nous décrivons les conditions sous lesquelles des nouvelles fissures de traction peuvent s’engendrer et se propager pour faire la connection avec des fractures existantes, de façon que le rocher se fracture en plusieurs blocs, menant à une résistance réduite. La résistance de quelques modèles fut égale a celle d’une fracture traversant toute la longueur du modèle. Pour les modèles ayant deux ensembles de fractures, la rupture a eu lieu sur une surface mixte, causée d’une part, par le glissement sur une fracture discontinue et d’autre part, par la rupture à travers le pont de matériel intact; ou bien par rotation et glissement des blocs. Cette dernière façon de rupture peut aussi aboutir à une très faible résistance des modèles.

Jan 1, 2003

By B. Solar Menéndez, M. B. Díaz Aguado, I. Á. Fernández, C. González Nicieza

The analysis of subsidence due to the opening of an underground void (mining, water exploitation or civil works hole) is a problem usually hard to solve. First of all, it requires a predictive model, in order to define both the displacement magnitude and area affected by subsidence. Such model should be validated with measurements of the actual movements sustained on the surface, in order to adjust it properly and enable influence of future behaviour in a reliable way. Two different kinds of problems might arise. On one side, it is necessary to control and measure surface movements in a very exhaustive way during a long period of time, beginning before underground works take place and finishing years after they are over. Furthermore, three factors bring in errors, some times of magnitudes higher than the displacement magnitudes measured. These include: the fact that reliable and long-term information cannot always be achieved; the precision of measuring devices; and the design of the topographical network itself. In addition, the predictive models more widely used only apply to certain excavation geometries, mainly to horizontal holes. In light of this background, the Group of Rock Engineering, of the University of Oviedo Mining Department, has developed a working methodology and a specific software tool, Subsidence 3D, to estimate ground displacements and strains. The program will allow for predictive models to be defined and also allows the treatment of data related with topographical marks and its comparative analysis with calculated results. The software has been programmed using Visual C++. Graphical outputs however are generated using AutoCAD 2000. This paper mainly refers to a practical situation, an underground coalmine, remarking the main difficulties arisen during the study of the available information and proposing how to solve them. A predictive model in subsidence 3D was established and validated. The actual behaviour of the ground was that in the model.

Jan 1, 2003

By J. -C. Trickett

The high-resolution three-dimensional (3-D) seismic reflection data acquired for Impala Platinum between 1998 and 2002 in the western Bushveld Igneous Complex form an integral part of Impala?s mine planning and development programme. These data are of sufficiently high quality to provide unprecedented 3-D models of the geological structure of the Merensky Reef and UG2 Chromitite Reef, from which the mine deduces the size, geometry and distribution of mineable blocks. Conversely, the seismic data details zones of un-mineable ground caused by structural disturbances in the form of potholes, fault zones and pegmatoid intrusions. Furthermore, variations in dip and strike are well imaged, allowing the mine planners to optimize the mine design and layout. Current interpretation work is focused on enhancing the accuracy of these geological models even further through the analysis of ?seismic trace attributes.? Preliminary testing on the Impala Platinum 3-D seismic volume has shown that attribute analysis has the potential to illuminate a number of geological reef disturbances that are otherwise ?invisible? in the original seismic time volume. Potential areas of improvement include inter alia: ?Improved definition of major fault zones ?Improved definition of zones of reef depression (?slumping?) ?Identification of reef terracing and/or reverse dip. Keywords: 3-D reflection seismics; Impala Platinum Ltd; seismic attribute analysis; seismic micro technology (SMT); rock solid attributes; dip-azimuth; instantaneous phase and similarity.

Jan 1, 2005

In ilmenite smelting, the FeO content of the feed material (nominally FeO.TiO2) is decreased by reduction with carbon. In a parallel reaction, a significant amount of the TiO2 is reduced toTi2O3. One of the striking features of these reactions is a consistent relationship between the extents of FeO and TiO2 reduction; this relationship is independent of furnace size. It was recently proposed that this relationship follows from the solidification behaviour of the slag, where the final slag composition corresponds to the minimum melting point (?eutectic groove?) in the FeO-TiO2-Ti2O3 phase system; the hypothesis is that solidification equilibrium with the freeze lining stabilizes the slag composition. If this is the case, the system of slag and freeze lining must be capable of correcting two types of disturbances: thermal and compositional. Thermal disturbances result from incorrect power input, for the feed rates of ilmenite and reductant. For example, excessive power input will tend to overheat the slag, causing the freeze lining to melt partially, establishing a new steady-state heat loss from the furnace. Compositional disturbances result from an incorrect reductant input for the given power and ilmenite input. In this work, the dynamic response of the slag and freeze lining to different inputs (flow rates of ilmenite and reductant, and power input) is modelled. The model is based on solidification equilibria, and quantified heat loss through the freeze lining. The conclusion is that the solidification equilibrium cannot constrain the composition to the eutectic groove for typical operating conditions. Keywords: ilmenite smelting, freeze lining, solidification, high-titanium slag

Jan 1, 2004

By A. Chryssoulis, D. Venter, R. Dunne

An often-overlooked parameter of flotation processing is the impact of surface chemistry. Flotation processing, being a heterogenous process is largely reliant upon the chemistry occurring at the interfaces between solid-liquid phases. Development of analytical techniques such as Auger electron spectroscopy, X-Ray photoelectron spectroscopy (XPS) and low energy electron diffractions (LEEDS) has allowed for a dynamic view characterizing surface composition and structures. The advent of ‘static’ systems, capable of measuring ultra-thin layers on surfaces at low concentrations, was the next step in surface analytical developments. In general, it is the low concentrations and fragmentation patterns which limit the analysis of certain chemical species at plant concentration ranges. At present, analysis of inorganic and organic surface modifiers by time of flight mass spectrometers with a variety of ionization techniques has become a common analytical method to measure chemical species on the outermost surface of mineral particles. By studying the relationship between surface analysis results with metallurgical outcomes, the implications of the presence of surface species can be determined. The presence of flotation activators or depressants can be established using Laser Ionization Mass Spectrometry (LIMS) and Resonant Ionization Mass Spectrometry (RIMS) which are highly versatile surface sensitive analytical techniques. A case study applied to sphalerite flotation in the Neves Corvo Cu-Pb-Zn concentrator and the implication inorganic surface modifiers have is presented. By determining the relative concentrations of Cu, Pb, oxidation products, Ca and other surface species in floated and rejected mineral particles, rationale for improving recovery and selectivity is elucidated. Keywords: Cu-Pb-Zn Flotation, Process Mineralogy, Surface Chemistry, Flotation kinetics

Jan 1, 2020

By A. V. Z. Brink

Rock engineering risk is defined in this paper as a function of the potential ground motion; the vulnerability of the workplace; exposure of people; and a general term – quality of information. The paper describes the development of prototype software that is a combination between an expert system approach for determining overall risk assessment, a risk control recommendation and a basic GIS (Graphic Information System) approach for graphically overlying input parameters and the output risk. The expert system uses a Bayesian probabilistic approach to combine various workplace-related information, a quantified seismological environment and the exposure of underground staff to provide an overall RE risk rating. The risk assessment is dynamic in that it is recalculated each time that any of the input parameters change, for example each time a seismic event is recorded in the area of interest. The code was tested on a data set from Savuka Gold. As risk assessment is not an absolute prediction of a specific outcome, it is therefore not possible to relate to individual case studies and the reliability of this method would only be determined after an extensive period of use with appropiate back-analysis. Le risque dans le génie minier est défini dans cette étude comme une fonction du mouvement potentiel de terrain ; la vulnérabilité du lieu de travail ; l’exposition des personnes ; et un terme général – la qualité de l’information. L’étude présente décrit le développement d’un logiciel prototype qui est une combinaison entre une démarche de système expert pour déterminer une évaluation générale du risque, une recommandation pour le contrôle du risque, et une démarche de SIG (Système d’Information Géographique) pour superposer graphiquement les paramètres d’entrée et le risque de sortie. Le système expert utilise une méthode de probabilité bayésienne pour combiner des informations variées sur le lieu de travail, des données quantifiées sur l’environnement sismique, et l’exposition du personnel travaillant sous terre, pour finalement produire un classement général de risque minier (RE). L’évaluation du risque est dynamique en ce sens qu’elle est recalculée à chaque fois qu’un des paramètres d’entrée change, par exemple à chaque fois qu’un évènement sismique est enregistré dans la région. Le code fut testé sur un ensemble de données obtenues de Savuka Gold. Comme l’évaluation du risque ne constitue pas une prédiction absolue d’un résultat spécifique, elle est par conséquent difficile à rattacher à des cas individuels et la validité de cette méthode ne pourrait être déterminée qu’après une longue période d’utilisation avec analyse rétrospective appropriée. Das Gesteinstechnikrisiko wird in dieser Arbeit als Funktion einer möglichen Bodenbewegung definiert; die Anfaälligkeit des Arbeitsplatzes; das Ausgesetztsein der Belegschaft; und ein genreller Begriff - Qualität der Informationen. Das Papier beschreibt die Entwicklung einer Prototyp-Software, die eine Kombination zwischen einem Expertensystemzugang für die Bestimmung der gesamten Risikobeurteilung ist, eine Empfehlung zur Risikokontrolle und eines fundamentalen GIS (graphisches Informationssystem) Zuganges für graphisch darüberliegende Eingangsparameter und das Outputrisiko. Das Expertensystem verwendet eine bayesische Wahrscheinlichkeitsannäherung, um verschiedene mit dem Arbeitsplatz in Verbindung stehende Informationen, ein quantitativ bestimmtes seismologisches Umfeld und das Ausgesetztsein des Untertag-Personals zu kombinieren, um eine gesamte RE-Risikobewertung zur Verfügung zu stellen. Die Risikobeurteilung ist insoferne dynamisch,daß sie stets nachkalkuliert wird wenn sich irgendeiner der Eingangsparameter ändert, z.B. jedesmal wenn ein seismischer Fall im Interessensbereich aufgezeichnet wird. Der Code wurde auf einem Datenbestand von Savuka Gold geprüft. Da die Risikobeurteilung nicht eine absolute Vorhersage eines spezifischen Resultates ist, es ist folglich nicht möglich, sich auf einzelne Fallstudien zu beziehen und die Zuverlässigkeit dieser Methode könnte nur nach einer umfangreichen Benutzungsdauer mit geeigneter Postanalyse bestimmt werden.

Jan 1, 2003

By L. Mpolokeng, J. P. Labuschagne, H. Yilmaz

"An investigation into pillar cutting was carried out at a platinum mine on the western limb of the Bushveld Complex. The focus was on crush pillar design and implementation in order to ultimately improve the compliance percentage for pillar cutting. The major findings from the investigation suggest that the pillar cutting problem lies with the implementation of the design rather than the design itself. Observations of the practical issues underground that prevent good pillar cutting were made. After these issues had been identified, recommendations to rectify these problems and a few other issues identified during the investigation were provided. The recommendations are aimed at improving the pillar cutting compliance and reducing the likelihood of pillar bursts or pillar runs, which will ultimately create a safer mining environment. Paper written on project work carried out in partial fulfilment of BSc. Eng. (Mining Engineering)"

Jan 1, 2015

By A. Kazemi, M. A. Ahmadi

Pressure tunnels are constructed nurously in related with powerhouse. In some cases, according to high internal water pressure, rock mass around tunnel can seldom suffer this pressure. So installation of concrete lining which interacts with rock mass and suffers parts of this pressure and transfers the rest of the pressure to the rock. In this paper hydromechanical interaction between rock and lining is investigated. With using empirical and numerical methods concrete lining for Symareh waterway is designed. Initial support of 10 cm reinforced shotcret with wire mesh and rock bolts pattern of 2.5*2.5 m with length of 4 m is suggested. By using FLAC package final lining with paying attention to axial force and momentum in reinforced concrete was designed. Reinforced concrete with 60 cm thickness and two rows of bars, 18 mm diameter and 20 cm spacing are designed. Also for preventing cracks in concrete which caused by the change of temperature and shrinkage, bars with 10 mm diameter and 25 cm spacing, and also bars with 8 mm diameter and 10 cm as minimum shear bars are suggested. Plusieurs galeries en pression se construisent en liaison avec les centrales électriques. Dans certaines galeries, suite à une haute pression interne de l'eau, le massif rocheux autour de la galerie ne peut pas supporter cette pression. L'installation d'une couche de béton a l'intérieur de la galerie donc réagit avec les roches et support d'une partie de cette pression et transfère le reste de la pression aux roches. Dans ce papier, l'interaction hydromécanique entre la roche et la couche en béton a été étudiée. En se basant sur les méthodes empiriques et numériques le système de support de galerie de passage d'eau de Saymareh a été conçu. Un soutènement initial d'une épaisseur de 10 cm de béton étant renforcé par un grill métallique et une maille de boulon (2.5 * 2.5 m) d'une longueur de 4 m a été proposé. En utilisant le logiciel de FlAC, la couche finale en béton selon les forces dans le béton a été conçue. Le béton renforcé d'une épaisseur de 60 cm et deux ranges d'armateurs (18 mm de diamètre) avec un intervalle de 20 cm a été conçu. De plus; pour éviter des fissures dans le béton suite au changement de la température et de l'extraction, des armateurs de 10 mm de diamètre et de 25 cm d'intervalle pour augmenter la résistance au sciesiement du béton ont été proposes Unter Druck stehende Tunnels werden hauptsaechlich im Zusammenhang mit Kraftwerken gebaut. In einigen Faellen, wo der Wasserdruck zu hoch ist, Kann selten die Felsenmasse diesen hoehen Druck allein aufnehwen. Deshalb werden sie mit Betonauskleidung versehen, die wegen guter Wechelwirkung mit der Felsenmasse einen Hauptanteil des Druckes aufnehmen Kann, wobei der Rest an die Felsenmesse weitergeleitet wird. In dieser Arbeit wird die hydromechanische Wechelwirkung zwischen der Gesteinmasse und der Auskleidung untersucht. Mit Hilfe empirischen und numerischen Verfahren sowie Kombination der beiden wurde eine Betonauskleidung fuer die Symareh Wasser Kannal koustruiert. Als erstes wurde ein 10Cm dicker armierter Beton mit einem Mashengitter von 2.5*2.5 sowie den gleichen Felsbolzenabstaenden und einer Laenge von 4 m vorgeschlagen. Mit Hilfe des FLAC Programms wurde die Hauptauskleidung unter Beruecksichtigung von Axialkraeften und Momenten im Stahlbeton koustruiert. Der 60 Cm dicke Stahlbeton wurde mit zwei Reihen von Stangen, 8 mm im Durchmesser und in Abstaenden von 20 Cm koustruiert. Ferner im Sinne der Vorbeugung gegen Rissen im Beton, die durch Temperatur aendeungen und Schrumpfungen bedingt sind, wurden Stangen mit 10 mm Durchmesser und 2.5 Cm Abstaenden zur Erhoehung vor Scherfestigkeit des Betons vorgeschlagen.

Jan 1, 2003

By J. M. Benson

Titanium is an exciting structural material that can offer significant strength-to-weight advantages over currently used alloys. However, its Achilles? heel is its costly, energy-intensive production process that effectively eliminates it from competing with aluminium and high-strength steels, apart from critical applications where titanium forms only a small component of the total cost. Current attempts are being made to reduce the cost of titanium products and these recognize the importance of minimizing the costs over the total production chain. Powder metallurgy (PM) technologies play a crucial role within this, as the output of the existing and potential primary metal production methods is in the form of sponge or powder. By using PM, costly remelting and forming operations can then be avoided, except in the manufacture of large components. Metal injection moulding (MIM) is an effective process for producing complex net-shape components in large volumes from metal powders. Nevertheless, the commercial use of titanium powders in this process is still in its infancy. The only major supplier of feedstock utilizes a polyacetal-based binder. This gives good green strength but requires a catalytic nitric acid process to remove most of the binder prior to thermal treatment. As this involves additional and expensive equipment and is a potentially hazardous process, there is interest in finding an alternative binder system that can be debound either purely thermally or that involves a less hazardous, more environmentally friendly solvent. This paper describes the use of capillary rheometry to characterize the influence of temperature and shear rates on the flow behaviour of potential binder systems for titanium MIM feedstock. Keywords Titanium, metal injection moulding, capillary rheology, feedstocks, powder loading.

Jan 1, 2011

By J A. H Campbell

AK6 is a Cretaceous aged kimberlite located in the north-east of Botswana, close to Debswana's Drapa and Letlhakane Mines. It was discovered by Debswana in 1969, but was considered unattractive from an economic perspective. In 2003, Debot Prospecting Pty Ltd ('Debot') re-assessed the area and with the advent of new prospecting technology, particularly large diameter drilling ('LDD') and more detailed ground geophysical surveys found AK6 to be of interest. In 2005, the Boteti joint venture was formed between Debot and African Diamonds plc ('AFD'), which covered a number of Prospecting Licenses, including that which contained AK6.

Jan 1, 2010

By R. Degel

Keywords: Pyrometallurgy, DC furnaces, electric smelter, FeCr, FeNi, FeMn, Si metal, ferro-alloys, platinum production, circular furnace, energy recovery system In 1906, the first submerged-arc furnace was supplied by SMS Siemag. Since then, the division has become established in various industries such as ferro-alloys and non-ferrous metals, and in numerous other special applications. During the evolution of this technology, more efficient units with longer lifetimes were developed. Today, especially the potential of DC-based smelters, raises worldwide attention, with some projects having already started to implement this kind of technology. This paper evaluates SMS Siemag?s general viewpoint regarding the potential application of DC smelter technology and possible options for the ferro-alloy and non-ferrous industry. SMS Siemag is currently executing a FeCr project in Kazakhstan, where four of the world?s largest closed-type DC smelting furnaces, with a power input of 72 MW, will be installed. These furnaces include the latest technological features of modern DC smelters, which are described in this paper. SMS Siemag has started a long-term research and development project allowing a direct comparison of AC versus DC technology on a large scale, using a recently installed 1 MVA test furnace at the IME at the University of Aachen, in Germany. For open-type ferro-alloy and Si-metal furnaces, SMS Siemag has developed an energy recovery system, which is presented in this paper.

Jan 1, 2011

With the passing of Dr William Bleloch on 20th June 1991, we lost not only a colleague and a good friend but a man who made a very significant contribution to the industrial development of South Africa. He can rightly be called the father of the ekctrochemical and electro-metallurgical industries in this country, since his ideas and dedicated work were directly responsible for the development of these large industries as we know them today.

Jan 1, 1991

By M. Grodner

Ground Penetrating Radar (GPR) is an electromagnetic geophysical reflection technique that maps reflections associated with a change in electric properties of the target medium. It can thus be used to map the geometry of geological features and fractures as these can have different electromagnetic properties to intact rock. GPR was used successfully to determine the position and nature of the fractures in the tunnel sidewall, in the area of the simulated rockburst experiment. By comparing the radar scans acquired before with those acquired after the blast, it was possible to determine which fractures were reactivated by the blast and where new fractures were developed. It was found that the mining-induced fractures that formed during the development of the tunnel were re-activated by the simulated rockburst, as indicated by their increased reflectance on the radar scans. In addition, several new tunnel sidewall parallel fractures developed in the area of the blastholes. GPR thus clearly shows how and where the fracture pattern changed as a result of the blast and contributed to the understanding of the mechanisms of damage associated with the blast, and perhaps rockbursts in general.

Jan 1, 2001