Search Documents

By P. I. Prescott

Ground calcium carbonate (GCC) is used in the paper, plastics, paint, rubber, caulks, and sealants industries. The favorable properties of GCC include high whiteness and brightness, low hardness, and outstanding rheology in water systems. The quality of calcitic GCC ores, which include chalk, limestone, and marble, is dependent on calcite purity and the nature and quantity of ancillary minerals. Wet and dry grinding is used in the manufacture of GCC. Ore processed by optical sorting, flotation, and/or particle size classification has higher brightness and lower abrasion. GCC markets are a function of the product's properties, purity, and cost.

Jan 1, 1995

By C. A. Moseley, M. B. Kahle

The Gulf Coast Region has been the center of extensive lignite exploration and development activity in the past 10 years. Currently, 27.2 Mt (30 million st) of lignite are mined annually, the majority of which is uncovered by large walking draglines. Projections indicate that production could reach 125 Mt (138 million st) by 1990. As mining moves to deeper depths, removal of overburden becomes the decisive factor in mine planning and cost. The geology of a region plays a key role in the selection of an overburden removal system. While alternate stripping methods must be analyzed to determine the most economical and operationally sound method, so far bucketwheel excavator systems seem to be the best method for removing large volumes of soft, unconsolidated material that is found at projected mining depths in the Gulf Coast region. Geology of Gulf Coast Lignites Extent Distribution of the principal tertiary lignite-bearing deposits in the Gulf Coast Lignite province extend from the Texas-Mexico border to the Alabama-Georgia state line (Fig. 1). The lignite-bearing strata includes portions of eight states: Texas, Louisiana, Arkansas, Missouri, Kentucky, Tennessee, Mississippi, and Alabama. Lignites occur primarily in the Wilcox, Claiborne, and Jackson groups in the Gulf Coast. The uppermost strata of the Midway group in Mississippi and Alabama also contain significant lignite resources. Reserves Commercial lignite seams in the Gulf Coast Lignite province range from 0.6-3 m (2-10 ft) in thickness. The estimated lignite resources throughout the Gulf Coast in seams greater than 0.9 m (3 ft) in thickness and up to 61 m (200 ft) in depth currently are estimated at 32 Gt (35 billion st). Table 1 shows these resources by state. Quality Lignite quality can vary within individual mining areas and seams. However, trends in quality occur because of the depositional environment, age, and west-to-east geographical location. Better quality lignites occur in the Wilcox group in Texas and Louisiana. Poorer quality lignites occur in the northern regions of the Wilcox group and those of the geologically younger Claiborne and Jackson groups. Environmental Conditions Gulf Coast province environmental conditions are ideal for successful mine reclamation. The lignite occurs in flat to moderately rolling terrain, a topography easily reproduced from the spoil dumps or spoil rows developed during the mining operation. High to moderate rainfall facilitates rapid revegetation. Evidence from current mine reclamation programs and ongoing test plot studies indicate that mined lands can be reclaimed to reach premining productivities. Sometimes productivities are even greater than that of premining conditions. Existing Mining Methods Present Mines & Production There are seven active mines in the Gulf Coast province, all located in Texas (Fig. 2). Lignite

Jan 8, 1983

By B. C. Paul, R. Q. Honaker, M. Huang

Froth flotation is now, the most commonly used method for cleaning fine-coal fractions in coal-preparation plants. Past research and industrial practice have demonstrated that froth flotation achieves excellent separation efficiencies for fine coals having only a small fraction of middling particles. However, the efficiency of froth flotation decreases sharply as the concentration of middling particles increases. This is due to the flotation of high-ash particles that have a small amount of hydrophobic coal present at the surface. Because gravity-based processes are much more efficient for the treatment of middlings, the application of centrifugal washing for fine-coal cleaning was studied with an emphasis on the primary cleaning of fine-circuit feed. Results are shown of a parametric study that used a semibatch Falcon centrifugal concentrator. The results of the study revealed that separation performance is a function of particle size, bowl geometry, feed solids content and feed rate.

Jan 1, 1996

By Milka Madahana, John Ekoru

Particulate matter is one of the leading pollutants in the mines and in the communities in the areas near or surrounding the mines. The availability of large Clinical and environmental data sets obtained from the mines has brought about the need to use better approaches to analyze the collected data. Prediction and control of particulate matter concentration in the mining environment is essential in minimizing air pollution and protecting the respiratory health of mine workers. The main objective of this research work is to analyze datasets obtained from a mining area using machine learning techniques which will then be followed by the real-time estimation of dust particulate in the mines. Datasets collected over 8 years in an hourly sampling rate from an open cast mine is cleaned and analyzed for trends and patterns. Artificial Neural Networks (ANNs), Support Vector Machines and decision trees techniques are applied to analyze and predict the particulate concentrate. The estimation of particulate concentration using Artificial Intelligence will significantly contribute toward the development of quantitative tools to be used in correlating of cause and effect of dust concentration in mines. The results obtained in this work will form a sub-unit of a respiratory health monitoring system for mine workers. The system is essential in the collection, analysis, and tracking of mine workers’ respiratory health, thus it forms part of an early intervention system for mine workers. From the existing theory, we expect the Artificial Neural Network will perform much better than previously used classical models.

Jun 25, 2023

By R. Hogg, T. F. Dumm

A simple shape description scheme has been developed which has the specific aim of distinguishing between angular and more rounded particles. The procedure involves fitting a general polygon (usually about 20 sided) to the particle profile. Geometric shape descriptors have been defined based on variations in the angles between adjacent sides and their radial displacement from the particle centroid. A two-parameter shape description, incorporating an angular variabli1ity and an elongation index, has been shown to be clearly consistent with visual observations. A single-parameter angularity index has been shown to be very sensitive to small differences in particle roundness and seems to provide a better description of angularity than other approaches such as signature and fractal analyses. The scheme has been applied to three sets of fine quartz particles produced by different grinding procedures. The results indicate that the technique is capable of distinguishing between angular and re1atively rounded particles and can quantify their specific shape features.

Jan 1, 1991

By R. J. Puchala, B. M. Hawrylewicz

High voltage electrical discharge in water causes instantaneous release of accumulated energy into water. The experiment described in this paper regards the utilization of the electric discharge phenomenon in rock splitting. The pressure in the shock waves created by the discharge inside a small volume of water enclosed in solid rock causes stresses which can result in breakage of rock. Holes drilled in tested samples were notched in order to weaken the tensile strength of the rock and achieve a uniformly directed split. The influence of the notches was theoretically analysed and compared with experimental data. Results of the tests have been statistically elaborated in order to correlate the newly-created surface to the energy supplied.

Jan 1, 1986

During development mining, ventilation capacity may decrease and the ventilation requirements may depart from initially planned values depending on the mining rate, increases in the methane emission rate, and changes in ventilation airway leakages. Insufficient ventilation air quantities and the occurrences of high methane liberation rates can overwhelm the existing quantity of ventilation air and result in elevated levels of methane gas during development mining. This condition can both limit the development of that section and increase the risk for an ignition that may lead to an explosion. Thus, the prediction of ventilation air requirements prior to mining can enhance worker safety by reducing the likelihood that explosive methane-air mixtures form. This study presents an approach for prediction of methane inflow rates using coalbed methane reservoir modeling. For this purpose, a two-phase coalbed reservoir model of a three-entry type roadway is developed. In the model, grids are dynamically controlled to simulate development of entries. Examples are given for methane inflow and ventilation air requirements as a function of mining rate, development section length, mining height, and the existence of degasification boreholes. This technology can be used to limit the methane concentrations occurring as a result of the influences of various coalbed and operational parameters.

Jan 1, 2008

By Roderick G. Eggert, John E. Tilton

During much of the 1970s and 1980s, world metal consumption grew more slowly than during the 19505 and 1960s. The slowdown contributed to surplus capacity and low real prices because actual consumption was consistently less than expected as new mining and mineral processing capacity came on stream. Over the last year or so, however, world metal consumption has picked up noticeably, raising the question, Has metal demand returned to the long-run growth rates more typical of the 1950s and 1960s than of the 1970s and 1980s? This paper examines this possibility and, more generally, assesses the factors that will shape demand for the major metals over the longer term. TRENDS IN METAL CONSUMPTION The extent to which metal consumption has recaptured the brisk growth rates typical of the 1950s, 1960s, and early 1970s is shown in Figure 1. This figure traces the consumption of crude steel, primary aluminum, refined copper, refined lead, and refined zinc between 1960 and 1987 for the western world, consisting of the OECD countries (including the United States), and the developing countries. Consumption increased in 1987 for all five metals, and preliminary data for the first six months of 1988 suggest even more substantial increases, at least for the United States (U.S. Bureau of Mines, 1988). However, Figure 1 also shows that the recent increases in consumption are not untypical of similar surges during earlier periods of economic expansion and thus may reflect only cyclical or temporary factors. In short, the available data are unable to provide a clear indication of whether recent increases in metal consumption reflect the beginning of a new era of faster growth or simply a cyclical and temporary upturn associated with the expansionary phase of the business cycle. Consequently, to pursue this issue, we are forced to examine the underlying forces that will shape metal demand trends over the next decade. The approach we have taken involves two steps. The first examines the prospects for overall economic growth. The expectation is, the faster the economy expands, the faster the production of metal-containing goods grows.2

Jan 1, 1989

By A. L. Boerner

Off-highway tire costs represent a significant portion of the total mining costs in openpit, truck-shovel operations. To extend the lives of tires, the site-specific factors influencing tire life should be investigated Valuable data can be obtained by combining historical operational data captured by a mine dispatch system with detailed tire and maintenance histories. Assuming that failure counts satisfy a Poisson distribution, F-tests can be applied to determine significant deviations from desired or target counts. The methodology developed in this paper can be used to identify the haul routes and loading and dumping zones that have significantly higher incidences of tire failure. Corrective action can then be targeted at these zones by modifying the shovel or truck operator practices; changing the haul route maintenance and clean up practices; or altering the bench, ramp or waste dump design parameters. An example is given of the correlation of tire separation and tire impact failures with haul routes for a fleet of nine Caterpillar 793C trucks in operation at the Chuquicamata Mine in northern Chile. A high incidence of impact failures was observed for the ex pit ore crusher and for tires installed in the left outer rear position on the trucks. The latter was postulated to be due to a preference for drivers to execute right-hand turns prior to dumping. Recommendations were made to revise crusher and dump cleanup practices and investigate the feasibility of super-elevating the surface of dumping zones to reduce ground pressure on the left rear tires.

Jan 1, 2002

By T. B. Linde

The Morenci In-pit Crusher and Conveyor System has been designed with safe production and cost savings in mind. Large open pit mines around the world have been installing semi-mobile crushers and linking them with a pit conveyor system to lower unit cost. At Morenci two 60/89 in. gyratory crushers are incorporated into the semi-mobile crushing plants. The ore is reduced to -8 in. and transported out of the mine on a 60 in. steel cable belt. This paper includes an overview of the Morenci In-pit Crusher and Conveyor System from the drawing board to open pit installation and finally a discussion on operating and repair considerations.

Jan 1, 1990

By D. Malhotra, R. M. Hoover

The effect of a surfactant, designated Syntex, on the wetting and spreading of hydrocarbon oil on molybdenite surfaces (faces) has been investigated experimentally through measurements of zeta potentials and factorially designed flotation tests. These studies indicate that Syntex has a positive effect in increasing molybdenite recovery in the rougher flotation circuit at the Climax mill. The analysis of experimental data using DLVO theory shows that the controlling factor in determining the magnitude of the repulsive energy barrier preventing oil from wetting and spreading on the molybdenite faces is the MoS2 zeta potential and the vapor oil droplet size. The role of Syntex in this case seems to be related to the decrease and stabilization of MoS2 zeta potential by Syntex adsorption and also to the emulsifying action of Syntex on vapor oil to provide a more favorable oil particle size.

Jan 1, 1976

By Meng Wang

"In this study, multiple methods that include geological surveying, laboratory studies, and numerical modeling have been used to study the deformation characteristics of a “deep inclined rock roadway with weak planes” (DIRRWP). Failure of the DIRRWP was found to be triggered initially by the shearing of the rock near the weak plane. The movement of the failed rock resulted in reduced confinement of the deeper rocks, and causing the failure of the supporting units and the severe deformation of the surrounding rocks. Hence, it is concluded that DIRRWP stability is affected predominantly by rocks near the weak plane. Corresponding control strategies for DIRRWP deformation were proposed: (1) greater support intensity is necessary to maintain the stability of the whole DIRRWP; (2) additional support is needed for rocks near the weak plane to reduce the potential of failure; (3) to increase the bearing capacity of the floor strata, as the floor needs to be supported; and (4) a supplementary support technique should be considered for cases of large deformation. The case study presented here indicates that the proposed control strategies can significantly reduce the potential of failure in rocks near the weak plane, thus preventing severe deformation of the DIRRWP.INTRODUCTIONAs shallow seams are mined out, the cover depths in most Chinese coalmines have become increasingly greater. Deep cover in a coalmine is considered to occur when the cover depth exceeds 800 m (Sun, Chen, and Miao, 2018). The loading and failure behavior of rocks in a deep cover setting are quite different from those in a shallow cover setting owing to the increase in in-situ stress, temperature, and hyperosmosis (Lobanova, 2008; Zhang et al., 2013). For instance, experience shows that bulking and dilating deformation in deep roadways is much greater than that which occurs in shallow roadways (Hou and Yang, 2018; Zhang et al., 2016). In addition, anisotropic behavior and thickness deviation of coal measure rocks, combined with the appearance of weak planes (e.g., faults, joints, and coal cleats) in coal and/or rocks, can significantly affect the stability of an underground roadway (Ghazvinian et al., 2013; Sun, Chen, and Miao, 2018). The presence of weak planes can significantly complicate displacement and stress transmission in nearby rocks. Additionally, tensile, compressive, and/or shearing failure in rocks near weak planes can be easily caused by high in-situ stresses in deep roadways; such failures may lead to further severe deformation of the surrounding rocks, resulting in roof falls and rib spalling (Kamata and Mashimo 2001; Wu, Ohnishi, and Nishiyama, 2004). A typical failure of the so-called “deep inclined rock roadway with weak planes” (DIRRWP) is shown in Figure 1. Severe deformation can be found near the weak plane. In this study, a plane or thin layer of rock/coal parting that can significantly reduce the strength of the surrounding rocks—and thus affect roadway stability—is defined as the weak plane."

Jan 1, 2019

By E. C. Grunsky

Spatial auto- and crosscorrelation assessment of variables can be carried out using quadratic function estimates. From the function estimates, multivariate relationships of the variables can be determined in the form of spatial factors. The calculation of the spatial factors requires computation of the corresponding amplitude vectors from the eigenvalue solution. This vector reflects the relative amplitudes by which the variables follow the spatial factors. Instability of some of the eigenvalue solutions requires that caution be used in interpreting the resulting factor pat- terns. A measure of the predictive power of the spatial factors can be determined from the auto- correlation coefficients and squared multiple correlation co-efficients which indicate which of the variables are significant in any given factor. The use of unconditional simulations provides a basis by which geological variables of varying spatial ranges can be modelled using the spatial factor technique. Simulations were generated for a variety of ranges and variables were created that form single or multiple combinations of the spatial patterns. The success of the spatial factor technique depends on the amount of associated noise, and the size of the neighbourhood relative to the spatial range of the variable. The predictive power of the components is dependent on these two factors. Problems with collinearity of variables can result in unrealistic eigenvalues and result in the failure of the method. Application of this method to spatial data in mineral exploration can assist in outlining spatially continuous zones of alteration associated with mineralization.

Jan 1, 1989

By D. W. Hendrickson

Cleveland-Cliffs views the mining process as ex- tending from mine planning to cargo loading including auxiliary systems such as materials handling and plant utilities. Process automation is recognized as an area that can provide significant improvement opportunities with less capital requirement than major flowsheet modifications. This article discusses the development and results of a strategy to allow and promote implementation of process-automation improvements at individual mines based on their economic priorities, taking advantage of common systems and concepts for use at multiple mines where practical. Specific process-control upgrade projects at Hibbing Taconite Co. and the Empire Mine are reviewed.

Jan 1, 1998

By B. Jensen, B. K. Abraham, G. J. Tuck, A. D. S. Gillies

A dust concentration meter has been developed with Australian coal industry support for the measurement of total airborne dust concentrations capable of causing explosions in underground coal mines. The instrument, The University of Queensland Dust Meter (UQDM), measures the effective dielectric constant of a mixture of coal dust and air that is drawn between the plates of a capacitor, the capacitance of which is measured by a ratio-transformer bridge and synchronous detector system. This technique measures small changes in capacitance to approximately 1 part in 106. The unique design of the capacitor sensor permits a precise volume of coal dust and air mixture to be sampled. This arrangement overcomes difficulties inherent in optical dust measurement. The meter is portable, battery powered, incorporates data logging and has intrinsic safety approval. The operation of the meter is discussed. The system is designed to monitor dust concentrations along a coal mining face and provide concentration profiles leading to the development of suppression strategies. If data from underground tests are available, the meter's potential to contribute to establishing safe working conditions underground will be discussed. Other areas of potential application of the measurement technique are also examined.

Jan 1, 1993

By M. J. Hrebar

A study was conducted to evaluate the applicability of large wheel loaders (Caterpillar 994 Class) for use as primary loading equipment in open pit iron-ore operations. Field visits were made to taconite and gold mines that used large wheel loaders. Information was gathered on loader selection rationale; operation and maintenance experience; and production, availability and costs. Brief time studies were conducted to indicate machine performance and utilization. This paper summarizes the field data that was collected including an economic comparison of wheel loaders and cable shovels in an iron-ore application.

Jan 1, 1997

By X. P. Zheng, H. K. Lin

During slow-cooling crystallization of iron-making blast furnace slags, most rare earth elements recrystallize in an artificial "mineral" identified as calcium cerite. Scandium (Sc) and europium (Eu), however, concentrate in a sheetlike "mineral." In this investigation, the mineralogy of this sheetlike "mineral" was studied. It was identified as being in the mica group and was called a rare earth-bearing barium fluorophlogopite. One of the objectives of this study was the recovery of this "mineral." The study indicated that it can be effectively recovered from the slag by flotation using dodecylammonium acetate or a combination of dodecyl-ammonium acetate and sodium oleate as collectors.

Jan 1, 1998

By James Sheridan

Risk can generally be defined as the possibility or chance of a loss corresponding to uncertainty. Analysis is the process for examining the components and relationships of a complex system in order to determine the impacts of its variables. Risk analysis is therefore a course of action taken to analyze multiple variables of a system that is subject to speculative outcome. When risk analysis is applied to mine development, it becomes the means for assessing and measuring those parameters that contribute to economic viability. Mining can be a risky business. It is composed of an assortment of factors that contribute to its financial outcome. Of these factors, the most consequential output is the net present value (NPV). Applying risk analysis in mine development can identify those factors having the most significant impacts and applying limits to those impacts. Mathematical computer modeling using Monte Carlo techniques is available and can be customized to suit specific mine development ventures. Essentially, those parameters that are not fixed values can have input variability. Rationally deduced engineering estimates should be the basis for determining the initial values applied as inputs in the models. Risk analysis therefore provides the user a means to identify, rationalize and assess the risks in mine development in an informed, calculated, and unbiased format for making economic decisions.

Jan 1, 2002

By P. Venkatasubramanian

The aerospace and nuclear industries have been applying systematic techniques for assessing the safety of complex technical systems for many years. These techniques such as fault tree analysis, failure mode, and effect analysis, etc., and more recently "expert systems," were developed to formally evaluate systems safety and to determine how hazards can he reduced. The application of formal methods such as expert systems has the potential for further reduction in both frequency and the consequences of mine accidents. This paper presents a general expert system model of diagnostic reasoning and describes its use as an inference method for analysis and problem identification for accidents due to the presence of an open cycle diesel-powered mine cars in underground coal mines.

Jan 1, 1987

By E. P. Gustafson

Demand by precious metals explorationists for cost effective means to target subsurface geologic structures worthy of evaluation by means of drilling has led to the use of the predictor-correlator technique. To locate polarizable targets, the predictor-a localized inhomogeneity in electrical properties-is placed at various locations in the computer-simulated subsurface region, and correlated with the potential distribution observed in the field. The correlation coefficient obtained is assigned to the subsurface location. IP targets are extracted by calculating a second correlation section based on higher-frequency illumination and subtracting it from the first. The locations of correlation difference correspond to the locations of polarizable mineralization.

Jan 1, 1989