Search Documents

By M. A. Rodrigues da Silva Enríquez

One of the rare consensual points among different resource-based economic analytical approaches refers to the strategic role of rent from mineral extraction, as a decisive tool to ensure that the temporary wealth generated in the present can turn into permanent income in the future. For this reason, evaluation, distribution and use of mining rent plays a central role in the sustainable development of mining cities. Brazilian legislation provides for this at the municipal level by means of participation in the financial results of mineral extraction accomplished in these municipalities, with the Financial Compensation for Mineral Exploration (CFEM). CFEM is a type of ad valorem royalty, which charges taxes of up to 3% of the net revenue of mineral production. However, legislation does not establish how these resources should be used. Therefore, there is wide variation in the use of CFEM income among Brazilian mining cities. A study from a sample of the 15 largest mining cities in eight Brazilian states made possible identification of two main patterns with regards to the use of CFEM which were labeled "sustained use" and " the pitfall of the single treasury." In that regard, this article discusses the pressuring factors that contribute to these patterns, as well as the institutional arrangements which may be more favorable to inducing more sustained use of CFEM.

Jan 1, 2011

By L. Vandamme, J. H. Curran

A fully three-dimensional hydraulic fracture propagation model, based on the Displacement Discontinuity Technique, is briefly described. Using this model, it is shown that the geometry of a propagating fracture is dependent on several factors, among which the fluid pressure distribution within the fracture plays an important role. The containment of hydraulic fractures is found to be dependent on stress and toughness barriers in the formation. Containment is also observed to be more effective with a decrease of the viscosity, pressure or flow rate of the injected fluid. The three-dimensional layout of the fracture is shown to have a definite influence on the width and pressure distributions within the fracture. The examples considered indicate the need for fully three-dimensional models, as complements to the commonly used two-dimensional and pseudo-three-dimensional models.

Jan 1, 1986

By Chun K. Ip, Simon T. Johnson, Robert J. Fowell

Laboratory conducted cutting tests at traverse speeds up to 1 m/s have been undertaken with high pressure water jets assisting the cutting action of drag tools. Four sandstones and one limestone have been investigated, which represents a wide range of compressive strength. Variables investigated include water jet pressure, nozzle diameter, depth of cut, traverse speed, jet position, and tool bluntness. The test programme has allowed a model to be developed which describes the action of water jet assistance for three conditions dependent on the ability of the jet to penetrate the rock: where no significant penetration occurs, where penetration is greater than 50% of the tool depth, and an optimum condition around 30% of tool depth.

Jan 1, 1986

By Jonathon M. Hanson, John F. Schatz

A combined theoretical and laboratory test program is described with the purpose of providing a useful model of the multiple radial fracturing process. A non-quantitative conceptual model is developed as the basis for detailed mathematical modeling and test planning. The model includes borehole pressurization, flaw rupture, and gas- driven fracture propagation phases. The laboratory tests are carried out in blocks of scaled rock simulant loaded to a true three-dimension stress state and with miniature propellant/explosive charges in a wellbore as the fracturing energy source. The conceptual model, fracture initiation modeling, and laboratory test setup have been completed and are described. The remaining work is ongoing

Jan 1, 1986

By V. Rastogi

Surfactant-based bactericides are able to control acid formation in sulfidic materials such as pyrite and sulfidic ores, thereby helping to abate acid rock drainage. Bactericides are used in the following two ways: as periodic or continuous spray treatments for the prevention of acidification of material actively handled and moved and in controlled-release form for reclamation. Site-specific bactericide treatments are designed for active sites and reclamation. Results from two active coal refuse sites show that acid production can be reduced by 88% or more. Results from reclaimed sites show that bactericide treatment can be more effective than the addition of alkaline materials such as limestone and can reduce acid production from 3,500 to <30 ppm. The controlled-release-pellets treatment outlasts the life of the pellets, as shown by a study of a site now 10 years old A single treatment sets up a change in site microbiology to replace acid-producing Thiobacillus ferrooxidans bacteria with heterotrophic bacteria and creates a stable site without the need for further treatments. A secondary beneficial effect of bactericides is on revegetation, and biomass from treated areas is almost 10 times that from areas not treated with bactericide. Depending on the application, bactericide treatment can be cost effective upfront and certainly long-term, compared to the perpetual water treatment that could be required, even after productive use of the site is completed

Jan 1, 1997

By S. K. Kawatra

With the increasing importance being placed upon modernizing the coal industry as a result of recent developments in the international energy balance, computer control has been and is being instituted in many coal cleaning plants. Control techniques that are well established in many base metal industries have been adapted to coal washing. Essential to any control scheme is an accurate measure of the parameter which is to be controlled. A sensor is required that will provide information both quickly and precisely. In fine coal circuits, the critical parameter that must be measured and controlled is the per- cent ash contained in the clean coal product and tailings. Measuring the ash content of these slurry lines on a continuous basis enables the operating conditions in the circuit to be adjusted so as to obtain optimum separation efficiencies at all times. An on-line ash monitor has been developed and tested at Michigan Technological University which is capable of making percent ash and percent solids determinations instantaneously. Two radioisotopes are employed in this system to generate signals that can be related to the density and the ash content of the slurry. Such data provide a means to execute a short term control strategy.

Jan 1, 1982

By V. Gangrade, J. Addis, S. Vanderslice

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are conducting research to improve the ventilation of large-opening underground stone mines. The mine ventilation in these mines are characterized by: (1) challenges related to keeping airflow velocities high enough to effectively remove or dilute airborne contaminants, (2) low pressure losses needed to move large air volumes of air, and (3) costly stoppings needed to direct ventilation airflows. Each of two field studies was dedicated to specific focus areas. The first focus area was the characterization of underground mine ventilation airflow. The primary means of airflow control in stone mines is through the use of freestanding booster fans. The primary goal of this study was to identify the effectiveness of various fan types and optimize their placement. Both traverse and grid-based airflow readings were taken at various distances from the fans, ranging from 70 ft to 425 ft away from the fan. The air readings were taken using a vane-anemometer and a handheld hotwire anemometer. The data was used to develop precise computational fluid dynamics models. The second focus area was to determine diesel particulate matter (DPM) concentrations in the mine. For large-opening underground stone mines, controlling DPM exposures dictates the design of the ventilation system. Therefore, researchers carried out the DPM sampling campaign to identify potential areas of concern within the mine. The samples collected during the campaign were analyzed using NIOSH Method 5040. The sampling was done using the Mine Safety and Health Administration’s (MSHA) compliance sampling methodology.

Feb 1, 2023

By M. J. McPherson, P. Mousset-Jones, J. Banik, F. Calizaya

Friction factors or coefficients of friction used to estimate the resistances of mine airways are, in the main, estimated from empirical measurements made in other airways considered to be of a similar geometry and type of lining. A somewhat more analytical approach, although still based on empiricism, is to estimate the ratio of the average height of the asperities to the hydraulic mean diameter of the airway (e/D ratio) and then to employ the Moody Chart or one of the equations that have long been established to represent the [coefficient of friction v Reynolds number curves] on that chart. Unfortunately, the Moody Chart and corresponding equations are based on pipes of uniformly distributed (sand grain) roughness whereas the asperities that exist on the surfaces of mine openings are frequently highly irregular both in their size and distribution. This is considered to be a major cause of discrepancies that have been found between coefficients of friction by the Moody Chart and those actually measured in mine airways. The work described in this paper examines an alternative method of estimating coefficients of friction for rough natural surfaces with uneven sizes and distribution of surface asperities. The technique utilizes the relatively recent developments in fractal analysis. A fractal dimension is determined from the topography of the surface. This has been correlated to coefficient of friction for a scale model of a mine airway. Further work is being carried out in actual mine airways. However, at this time, it appears promising that the fractal method may allow coefficient of friction to be predicted for given types of strata and method of roadway drivage.

Jan 1, 1993

By W. L. Fourney, D. C. Holloway, J. W. Dally

Introduction Improvements in the process of rock excavation by blasting involves better control of one or more phases of the fracture process immediately after detonating the ex- plosive charge. Total control of the process involves individual control of (1) The number of fracture planes. (2) The crack initiation sites. (3) The direction of crack propagation (usually radial). (4) The stress field driving the fracture front. Fracture plane control is usually accomplished today by using the smooth wall blasting method; however, investigations by the authors (1) indicate several areas where this method could be improved. These improvements include: a) generation of stress concentration factors at the location of the initiation sites; b) protection of the remaining region of the borehole wall to inhibit initiation of any cracks not associated with the fracture plane and fragmentation pattern; c) limit peak detonation pressures to avoid borehole crushing and maintain by stemming residual gas pressure in the bore- hole during the crack propagation period. This paper describes experiments con- ducted with a charge holding device fabricated from thin-wall steel tubing which was partially slit at fracture locations. The tube lined the bore-hole in laboratory tests to simulate smooth wall blasting. Results showed close control could be achieved relative to both the number and the location of the fracture initiation sites.

Jan 1, 1977

By Hugo E. Camargo, Amanda S. Azman, Brian Kim

Repeated noise exposure and occupational hearing loss are common health problems across industries and especially within the mining industry. Large mechanized processes, blasting, grinding, drilling, and work that is often in close quarters put many miners at an increased risk of noise overexposure. In stone, sand, and gravel mining, noise is generated from a variety of sources, depending on the type of ore being mined as well as the final consumer product provided by that mine. Depending on the source of noise generation, different strategies to reduce and avoid that noise should be implemented. The National Institute for Occupational Safety and Health (NIOSH) has evaluated the noise profile at three operational surface stone, sand, and gravel mines. A-weighted sound level meter data as well as phase array beamforming data were collected throughout the mines in areas with high noise exposure or high personnel foot or vehicle traffic. Sound level meter data collected on a grid pattern was used to develop sound profiles of the working areas. These sound contour maps as well as phase array beamforming plots were provided to the mines as well as guidance to modify work areas or personnel traffic to reduce noise exposure.

Jan 6, 2022

By T. Wisdom, D. Romo, G. Seale, R. Jansen

Thickening remains relatively misunderstood since it is typically near the end of the process and not directly involved in metal recovery. When operating well, thickeners are ignored and left to run independently, the ‘out of sight, out of mind’ phenomena. However, when operating poorly, there is a lack of basic understanding and remedial actions to solve issues are reactionary rather than proactively addressing shortcomings. This series of papers breaks down in sequential order the stepped phases required to gain an appreciation and thorough understanding of the science behind thickeners, and key thickener components, and basic troubleshooting skills. This second paper starts with identifying the different approaches to thickener test work including static and dynamic settling tests followed by high-rate versus paste thickening. Complimentary to test work, the mechanisms surrounding coagulation and flocculation are presented and explained. The basic mechanisms for coagulation and flocculation are discussed to support the different test work approaches and provide the reader with the basic background.

Mar 2, 2022

By Richard K. Thorpe, Francois E. Heuze

The concept of a reusable underground nuclear test facility, named HEDEF, has been under study for some time. This rock chamber would have to be engineered to sustain the repeated mechanical and thermal shocks of internal explosions. In this paper, we summarize preconceptual studies performed in support of HEDEF, including -simple dynamic calculations for internally loaded tunnels, -outline of proof-of-concept tests of proposed reinforcement, - and initial dynamic testing of reinforcement components in an underground high explosive (HE) test.

Jan 1, 1986

By A. Festa

Secondary crushing often gets good press for its increases in energy efficiency and SAG milling rates but for a project considering this option the proposed benefits soon get overshadowed by implementation concerns. Reverse engineering from the published case studies is risky unless the reader understands the drivers impacting stability and operability of the circuit. This paper discusses the features of secondary crushing for Greenfield and Brownfield SAG mill grinding circuits. It is the author?s view that secondary crushing rarely adds value to a Greenfield project and restricts future expansion. Its application is best retro fitted to Brownfield operations where the benefit gained for capital expended is excellent. Two case studies are presented to reaffirm these statements. The first case study shows that the implementation of partial and total secondary crushing increases SAG mill power efficiency and it offers substantial incremental increases in milling throughput with staged capital investments for the crushing and grinding circuits respectively. The paper provides a critical analysis of process conditions for secondary-crushed grinding circuits, with particular emphasis on Brownfield circuit retrofits. Furthermore, the second case study quantifies the economic impact of secondary crushing on circuit design for plant start up and it illustrates the limit imposed on plant expansion.

Feb 23, 2014

By Thomas F. Pedersen, J. Jay McNee, Alan J. Martin

Field sampling was conducted in Lake Junin, Peru in order to assess the post-depositional reactivity of the highly contaminated lake sediments. High resolution profiles of dissolved Fe, Mn, SO42- and H2S across the sediment-water interface illustrate that the organic-rich sediments in the main basin become anoxic within several millimetres of the sediment-water interface. These permanently submerged deposits in the main basin serve as a diffusive sink for dissolved Zn and Cu. Conversely, the periodically unsaturated deposits in shallow areas are characterized by the remobilization of Zn and Cu in the deep acidic (pH < 4) pore waters, resulting in the release of these metals to the overlying water column.

Jan 1, 2000

By Alena Conrads, Markus König, Markus Scheffer, Markus Thewes, Hannah Mattern

"INTRODUCTION In recent years, the development of tunnel boring machines has revolutionized the tunneling industry. The general structure of a tunnel boring machine (TBM) can be described as a multi-component system. To achieve high performance rates, machine elements have to perform reliably. Performance losses and interruptions of the construction process should be prevented or at least, reduced to a minimum. In order to achieve high advancing rates, cutting tools must be in good condition at any time. Furthermore, failure of individual tools might result in increased and faster wear of remaining structural components. For this reason, maintaining and replacing cutting tools is crucial to prevent project delays due to insufficient boring performance. Precise prognoses concerning the prevailing geology are infeasible and thus, efficient scheduling of maintenance actions is challenging. The intention of this work is to analyze different approaches of TBM maintenance in soft ground. Different strategies are analyzed by the use of a simulation approach. Cutting tool condition is regarded as performance limiting factor. The maximum operation time of the cutting tools is determined using the “Soil Abrasivity Index”. A case study serves to show the effects of different maintenance strategies on total project duration. SCHEDULING OF MAINTENANCE ACTIONS Scheduling maintenance actions of single and multi-component systems concerns numerous fields of industrial production. Concentrating on mechanized tunneling in soft ground, cutting tool maintenance represents the most common reason for intermission of advance (Köppl 2014). In literature, time-based and condition-based maintaining techniques are widely discussed. The following section outlines the principles of time- and condition-based policies. Furthermore, examples for their applications in recent research are given. Time-Based Maintenance In general, the time-based maintenance approach assumes that the failure behavior of the system components is predictable. Maintenance actions are scheduled according to predefined intervals (e.g., hours, days, weeks). A detailed analysis of preventive repair times or interval forms the basis for maintenance decisions. For this approach, an adequate quantity and quality of data is fundamental. Numerous studies deal with the analysis of time-based maintenance for production equipment. In fields of mechanized tunneling, unplanned machine downtimes restrict the applicability of time-based maintenance approaches. Thus, this paper mainly focuses on condition-based maintenance."

Jan 1, 2016

By Y. S. Kim, A. Bailey

A feasibility seismic refraction and reflection field survey was conducted at the U. S. Borax Company open-pit mine, Boron, California by the writers during the weekend of March 13 and 14, 1976. This field survey was carried out as a preliminary investigation primarily for the purpose of evaluating and establishing the ability of such geophysical techniques to locate and outline the subsurface openings of the old room-and-pillar mining under the present open-pit. The value of such knowledge about the old underground workings is directly related to the safe and economical operation of the open-pit mine for the company. Although mine maps of the old underground workings are available at the mine, the extent of roof and wall cavings and the present condition of the old underground openings are unknown. Owen and Suhler (2) are the first investigators who used electromagnetic methods, Pulse-Echo System, and electric resistivity measurement to solve the problem without success. A few years later, Herzig and Owen (1) attempted to solve the problem with application of earth resistivity measurement method with unfavorable results. The U. S. Borax Company carried out an extensive study for slope failure problems of the open-pit with application of dipmeter measurements. However, the slope stability study was not correlated to the old underground openings lying under the present open-pit (3).

Jan 1, 1977

By J. Alvarez, S. Helle, U. Kelm, M. Pincheira

The principal geological and mineralogical characteristics of Chilean porphyry copper deposits are described. Elevated contents of fine grained ore and gangue material may cause copper losses and pose problems or render useless the flotation process. Examples of chalcopyrite and bornite size distributions are given. The state of the art of mineralogical and mineral chemical characterization in Chile is evaluated permitting analyses to lm and nm level by lacking the regular use of direct surface analysis.

Jan 1, 1998

By Donald E. Ranta

Many portions of the mining industry are under intense pressure to reduce costs while commodity prices languish. In response, global Internet-based marketplaces to deliver business-to-business (B2B) e-commerce solutions are being established to reduce costs and improve efficiencies across the mining industry supply chain as well as with customers. Over time these marketplaces will likely evolve to create an integrated supply chain solution, layer in value-added services, and develop mining community portals with industry content. Significant opportunities to help reduce costs and create value are available in mining e-procurement as well as in on-line product sales. The supply chain for the industry is highly fragmented and many mining companies have numerous inefficiencies in procurement. An e-procurement marketplace (or "exchange") can immediately address these inefficiencies and offer numerous benefits to buyers and suppliers. These benefits include improved sourcing options, inventory cost reduction, transaction cost reduction, access to value-added services, lower customer and supplier acquisition costs, improved reach, and improved information flows.

Jan 1, 2001

By A. Konya

"INTRODUCTION Underground Mining and Construction projects face several challenges unique to the underground environment compared to the surface environment. The goals of an effective blasting program are the development of a blast pattern that minimizes cost, maximizes face advance, and provides the desired fragmentation and face profile. In addition to these , mines must consider the very real operational problems that occur such as drill deviation, ground vibration, and deadpressing or sympathetic detonation of explosives. These operation problems lead to increased costs and decreased production in the mine, hurting the bottom line. Combined with these problems, underground blasts can be difficult to monitor and evaluate due to tight spaces, dust during the blast obscuring video, and the need to evacuate the immediate area with no clear line of sight to observe performance. This creates an environment which most mines know that blasting can be improved in their underground operations, yet most are hesitant to change due to fears of the shot freezing, misfires occurring, and questions about how to achieve a proper design. The explosive companies and shot service providers also offer limited assistance or knowledge in the underground blasting realm, unlike with surface blasting, leaving many underground operations in the dark. It is for these reasons that most underground operations are operating decades behind the current technologies and incurring significant costs, both real and hidden, from there blasting operations. This paper discusses philosophical changes to designs that need to be made for effective design and modifications of underground blast patterns to prevent deadpressing and precompression of modern explosive products (Konya, Konya, & Worsey, Modern Blasting Method Selection, 2017). While numerous different methods of underground heading development exist, there are two types that are used in a majority of mines around the world, these are the burn cut and the V-cut. The burn cut is a parallel cut that has holes that go straight into the face and are primarily used in smaller opening (due to ability to pull deep rounds with smaller room widths) and metal mines (helps in ore dilution and greater fragmentation). The V-Cut is a cut that uses angled drilling towards the center of the face (in the traditional method) and is primarily used in underground aggregate operations due to its cheap cost but larger fragmentation sizes and greater throw of the muckpile. This paper will discuss these two forms of cuts specifically with the understanding that modifications to these can be applied to other parallel and angled underground heading techniques. BURN CUT The burn cut is one of the older forms of underground blasting, where a part of the blast (burn) of a shot is heavily loaded with additional empty (relief) holes with the goal of smashing (aka burn) and pushing/blowing all the material in the burn out to provide relief for subsequent blastholes. The relief holes in the burn cut provide a parallel relief for the holes that are firing to break too creating a second plane of relief, however these are extremely small and can cause many problems if a design is improper."

Jan 1, 2018

By Anthony D. Hammond

Geographic Information Systems (GIS) are powerful analytical and data display tools for mining industry management, capable of linking spatial features with tabular data and integrating communications across departmental boundaries. This GIS application concentrates in four technical areas of underground mining: ownership and mineral claims; exploration management; production; and mine safety. GIS provides land and exploration managers with the ability to consolidate and archive claim data and to georeference property maps defined in local coordinates into world coordinate systems. It facilitates optimal siting and querying of service installations and refuge chambers relative to production centers. GIS&apos;s proximity analysis identifies areas of potential safety concern and points to and maps the shortest routes to emergency exits, facilitating the prompt evacuation of mine personnel.

Jan 1, 2002