Search Documents

By V. F. Swanson

A mathematical model for free and hindered settling of minerals was developed. This paper describes how to apply the model in designing systems, such as fluidized bed, elutriation, mixing pumping systems, involving solids and fluids.

Jan 1, 2000

By Sidney L. Hansen

This report was written because of concerns of the possible error involved when stopping leakage is incorrectly assumed to be turbulent. It is common practice to use turbulent flow to characterize each airway branch for computer models of mine ventilation circuits. This report addresses computer methods to accurately model air-leakage paths. A graphical method is described for deriving the equations of leakage through stoppings. The significance of modeling leakage according to the proper flow regime (turbulent or laminar) is demonstrated by the following method. A hypothetical mine was developed to represent present-day conditions. The stoppings of the mine were chosen to leak according to laminar flow properties. The mine was represented by constructing two base models. One base model used turbulent leakage equations for each stopping, while allowing the corresponding resistances to vary. The other base model used the correct laminar leakage equations and held corresponding resistances constant. The mine circuit was then expanded to demonstrate future development. The expanded portion was designed with stoppings that were identical to those in the base mine. The mine in the future state was represented by two projection models. Each projection model was an extended version of its associated base model; one used turbulent leakage equations and one used laminar leakage equations for stoppings. The laminar projection was theoretically correct and is used as a basis for comparison of differences in airflow quantities. Rather than modeling every leakage path for stoppings, a more practical approach is also discussed. A good level of accuracy is maintained by combining leakage paths if the proper flow equations are used. This method was used on the hypothetical mine projection and the flows were very similar to the theoretical values.

Jan 1, 1989

By Tom Plouf, Deepak Malhotra

INTRODUCTION The U. S. mining industry experienced a severe recession in the early 1980's. This resulted in the realization that the domestic mining industry had to compete on a global basis and only the strong or the low-cost producers would survive. The economic viability of a mining company not only depended on maximizing mineral recovery but also on its ability to do so at minimum cost. Companies had to become more productive not only by cutting costs, but also by developing and/or evaluating new technologies in existing or new plants. Several innovative concepts, including in-pit crushing and conveying, fine crushing, improved classification equipment, flotation, column flotation, pressure filtration, etc., have been developed in recent years. This paper addresses the impact of new flotation concepts and equipment on mill design. MILL DESIGN PHILOSOPHY Modern mill design, especially for large capacity plants, has its foundation in minimizing capital and operating costs. Capital costs can be minimized by minimizing the various components of the capital cost: infrastructure, equipment, instrumentation, structural, initial spare parts costs, etc. All these costs are minimized by simplifying the mill design and/or process flowsheet. The simplified process flowsheet, where applicable, consists of a single stage primary crusher followed by a semiautogeneous - ball mill grinding circuit to produce feed for a flotation circuit. Multiple flotation circuits have been eliminated in most cases. These concepts minimize the cost and encourage the use of large capacity equipment while maintaining optimum metallurgical recovery. The philosophy of mill modernization/modification is generally driven by the desire to increase the mill capacity within the limits of the existing mill building. This need is facilitated by using large size flotation equipment and eliminating multiple parallel flotation circuits in order to minimize capital and operating costs. Conventional flotation machine development has paralleled this mill design philosophy. FLOTATION CELL DESIGN Since froth flotation has been the most widely used separation process for over half a century, one would expect that it would be possible to design and select flotation machines for specific applications based on scientific principles. But this has not been the case. Best judgment, experience and personal prejudice have played a key role in equipment selection. These factors, along with the difficulty of evaluating new concepts in commercial plants, has slowed progress in implementation and commercialization of innovative ideas and/or equipment. Conventional Flotation There have been no major technological advances in conventional flotation cell design in recent years. A recent flotation cell survey indicates that 'larger flotation cells are still the order of the day.”(1) A comprehensive review of design of flotation machines indicate that they have been mechanically redesigned and are generally simpler and easier to maintain and less expensive to manufacture. (2,3) The approximate chronological development of conventional cells from the 25 cubic foot cells to the 3000 cubic foot cells, which were recently installed at the Copperton concentrator of Utah Copper, is given in Table 1. Larger flotation cells are the obvious choice for new plants or plants looking for expansion because of the following reasons: • They have lower capital cost per unit volume • Installation costs are generally lower because fewer units require less space • Maintenance costs are lower because of fewer mechanisms • Power requirements (HP/ton dry feed) are generally lower • with increased flotation cell size as illustrated in Table 2 [Table 1. Conventional Flotation Cell Size Development Year Individual Cubic Cell Size, Feet 1925 25 1935 50 1960 100 1965 300 1970 500 1975 1,000 1980 1,500 1985 3,000]

Jan 1, 1989

By T. Hudaverdi

Airblast, the focus of the paper, is defined as blast induced atmospheric pressure waves. High overpressure levels may cause breaks of windowpanes, and plaster cracks. Additionally many mines come across psychological responses of residential areas. In this paper the monitoring of air blast is explained and evaluation procedures are defined. The allowable limits of the air blast are presented. The scaled distance approach developed for the prediction of airblast is explained. For the very rapidly growing cities, like Istanbul, the required raw materials for the construction industry are supplied from quarries in the vicinity or from inside of the city. With further growth of the population density, many quarries approach suburban areas and it will be more important to minimize the adverse effect of the blasting operations in the near future. In this paper the airblast levels that monitored in Cendere Region Quarries near Istanbul are presented. The suggestions put forward to control airblast levels.

Jan 1, 2006

By Kirk Conway, Richard L. Unger

The U. S. Bureau of Mines conducted a research project to analyze the design of underground mining equipment with respect to ease of maintenance and maintainer safety. The work included a review of maintainability design literature, an analysis of maintenance related accident data, field reviews of equipment designs, and interviews with mine maintenance personnel and equipment manufacturers. Based on the findings, a set of maintainability design recommendations have been prepared. The final recommendations document includes maintainability engineering information for equipment designers, as well as a buyers' guide to aid purchasers of mining machinery in evaluating the maintainability of equipment.

Jan 1, 1992

By J. Derwin King, Harrison R. Cooper

Applications of nuclear magnetic resonance (NMR) offer possibilities for on-line sensing of the concentrations of several elements in flowing sample streams. In addition to hydrogen, these elements, generally of low-order atomic number, include aluminum, phosphorus, fluorine, sodium, boron, and lithium contained in minerals having commercial importance. Many such elements have been difficult or impossible to successfully measure on-line using the more familiar X-ray fluorescence and neutron activation analysis techniques. The availability of practical on-stream analysis methods is essential to applying advanced controls to processes incorporating these elements. On-stream NMR instrumentation has been demonstrated in the past for several process applications including, as an example, coal flow and analysis; and the technology has recently been extended to the measurement of phosphorous BPL in Florida beneficiation plants. The technique involves simultaneous sensing of proton (hydrogen) and 31P intensities to provide data for continuous calculation of BPL in the phosphate through calibration to volume fractions of water and solids. Initial operating results are described using the PhospholyzerTM on-stream phosphorous analyzer designed for plant application.

Jan 1, 1990

By Jasinder S. Jaspal

The United States has very large coal reserves in seams that are less than 1065 mm (42 in.) thick. These reserves are often not mined because of the difficulty of working in low heights and, in most cases, the seams are beyond the technical or economical limits. It is estimated that the remaining reserves in 355 to 710 mm (14 to 28 in.) thick seams that are not faulted or intruded, dip less than 15° and under a cover of 610 m (2000 ft) or less are nearly 910 Gt (1 trillion st). This is a very large percentage of coal reserves in the United States (Unrug, 1985; DuCarme et al., 1990). The US Bureau of Mines is attempting to develop new techniques for mining 150 to 1065 mm (6 to 42 in.) thick coal seams. Research has focused on existing thin seam mining techniques, testing of small- and full-scale physical models of the Bureau's slot mining concept and computer modeling of the full-scale process. In 1986, only 21 % of the total US coal production came from -1065 mm (-42 in.) thick seams. Of that, 355 to 710 mm (14 to 28 in.) thick seams share of production was minimal, probably 5% or less (Mayercheck et al., 1990). This shows that the thin seams, particularly the seams 355 to 710 mm (14 to 28 in.) thick, have not been mined to the extent of the available reserves. Thin seam coal, generally, is of premium quality. As thicker seams are depleted, the mining of thin seams could become more important. Thus, there is a need to develop technology to mine these seams (J. Farinelli et al., 1987). A successfully applied technology could change reserve categorization. In the Appalachian Plateau there are 417 Gt (460 billion st) in 355 to 1065 mm (14 to 42 in.) seams. This represents nearly 9.2% of the US remaining reserves (Unrug, 1985). At depths of 152 m (500 ft) or less, the Appalachian Plateau has about 214 Gt (236 billion st) of reserves in 355 to 1065 mm (14 to 42 in.) thick seams. Other mining areas also have substantial coal reserves in this seam thickness category. Those, however, are not as attractive for mining as the Appalachian Plateau. In the past, most of the reserves of the Appalachian Plateau region were partially worked by contour and highwall auger mining. It is estimated that these mining systems had left some 40,230 km (25,000 miles) (Readers Digest, 1987) of unreclaimed highwalls. The Bureau recognized this situation. In FY1987, the agency initiated a research project to develop anew technology for mining thin seams of the Appalachian Plateau.

Jan 1, 1992

By R. L. Grayson

In 1995, the United States Congress abolished the Bureau of Mines in the US Department of Interior. But Congress preserved the safety and health research functions being performed at the Pittsburgh and Spokane Research Centers. These functions were transitionally housed in the US Department of Energy before permanently merging with the National Institute for Occupational Safety and Health (NIOSH), Department of Health and Human Services, in October 1996. Since the rnerger of the former Bureau of Mines with NIOSH, there has been an active evaluation of ongoing research activities, significant interaction with stakeholders, and the development of a process leading to "data-informed" priority setting. This paper reviews the current surveillance information concerning the level of injury and disease from mining work and discusses how research priorities are evolving to improve the contribution of research to the prevention of injury and disease.

Jan 1, 2000

By L. G. Stolarczyk

In-mine Continuous Wave (CH) Radio Imaging method (RIM) instrumentation has the capability of measuring EM wave propagation constants in layered formations. The RIM method is based upon the fact that seams of coal, trona, potash, quartzite, gilsonite and oil bearing sands form natural waveguides for low loss transmission of electromagnetic (EM) waves. The waveguide forms whenever the seam is bounded by more conducting claystone, mudstone, shale or in the case of oil/gas traps, by a floor of saline water. Disturbances caused by faults, shear zones, paleochannels, sills and dikes significantly alter the propagation constant. The analytical values of the EM wave propagation constants depend on the physical and electrical parameters of the seam. The values are presented in this paper in a graphical form to assist in the interpretation of RIM tomographic images. This paper compares in-mine geologic mapping obtained during mining to tomographic images of the geologic disturbance zones in a Central Utah coal mine.

Jan 1, 1989

By Hardy J. Smith

The rock mass parameters which need be evaluated to estimate the rippability of rock are briefly outlined and their significance is discussed. Several methods used for estimating rippability are compared, and the advantages of taking into account a wide spectrum of rock mass parameters are emphasized. A systematic means of numerically weighing six rock mass parameters to produce a Rippability Rating (RR) is recommended, and a method of correlating this rating with the refraction seismograph method and with tractor horsepower is shown. Although the overall method demonstrated is systematic and yields specific numerical results, an integrated approach is recommended to its application, taking into account: the Rippability Rating; seismic velocity and geologic material; and other engineering judgment factors.

Jan 1, 1986

By S. B. Patton

A comprehensive approach to the development and organization of an expert system that is designed to assist electricians in diagnosing electrical faults m mining machinery is discussed. The system includes diagnostic, reference, and tutorial programs. The diagnostic portion of the system is based on a causal-reasoning approach which is used to establish a hierarchy of symptoms and the subsequent production rules for identifying component-level failures m the motor-control circuit of a shuttle car. With this approach, conclusions are developed directly from knowledge of the circuit and its behavior (in both working and failure modes) based on first principles, rather than the heuristics of a domain expert. The symptoms and their hierarchical structure an: formulated by creating "what-if" scenarios and performing a qualitative circuit analysis for each fault Techniques for incorporating interactive graphical displays of the circuit schematic into the diagnostic portion of the system are also presented. Supportive computer programs that provide' reference material and tutorials on the circuit are also described.

Jan 1, 1989

By A. Bayer, T. Klopfer

"As a leading global strategy consultancy, Roland Berger Strategy Consultants firmly believe that the issue of sustainability is at the core of every business activity. Thus, strategies to enhance corporate sustainability (CS) are an essential cornerstone in the consultancy's approach to develop and implement new strategic concepts for the clients. In this paper, the authors conclude that innovation is the only solution possible to guarantee growth and welfare gains while achieving sustainable development. More efficient and effective ways are necessary to enable technical and social breakthroughs. To illustrate Roland Berger Strategy Consultants's vision on CS, four selected cases from the basic resources, energy and utilities sectors are presented. They demonstrate that the implementation of a CS strategy does not only refer to CEO spheres and are by no means just a moral justification for current business practices. Rather they show that the decision to opt for these new ways also opens up multiple opportunities."

Jan 1, 2005

By John K. Kellis, Fazley Azhar

Advancements in AC drive technology offer conveyor designers a viable drive alternative for conveyor systems which require accurate load sharing as well as multiple drive systems. Recently developed AC drives have the ability to accurately control the output torque of AC motor. These AC drives, compared to current DC drives, offer superior performance characteristics while enjoying the benefits of an AC motor. Conveyor applications and case studies incorporating this AC drive technology are presented for review.

Jan 1, 1998

By Mark S. Stagg, Michael J. Nutting, Douglas R. Barlet

Single-row bench blasts at a reduced scale in the field were used to study the effects of delay time on fragmentation. Nine shots with a spacing of 21 in. and a burden of 15 in. (S/B = 1.4) and nine shots with a spacing of 30 in. and a burden of 15 in. (S/B = 2.0) were completely screened to determine particle size distributions. Delay intervals between holes ranged from 0 to 45 msec, corresponding to effective delay intervals ranging from 0 to 36 msec per foot of burden. Each shot was instrumented with strain and pressure gages to measure in situ blast dynamics and to evaluate interactions between blastholes. Finer overall fragmentation was produced for shots with delay intervals between 1 and 17 msec per foot of burden. Only for shots within this optimum delay range was it observed that the strains induced by stress waves constructively interacted with strains induced by gas pres- sure from an earlier detonated hole. Coarsest fragmentation resulted at delay intervals less than 1 msec/ft, where stress waves from each hole were observed to interact destructively, and at delay intervals greater than 24 msec/ft, where no inter- action between holes was observed, indicating a condition that can be considered as the firing of single hole shots independently.

Jan 1, 1986

By Jamal Rostami

With the recent technological advances; Tunnel Boring Machines (TBM) have become a viable economic alternative to drill and blast in hard rock excavation. These machines are finding increasing use in underground mine development due to the potential benefits they offer. The successful application of TBM technology to mining depends on the selection of the most suitable equipment and cutting tools for the rock and ground conditions to be encountered. In addition to required testing and geotechnical investigations, cutterhead design optimization is an integral part of the machine selection to assure a successful application of the machines in a specific project. This paper presents and discusses the back-ground of TBM application in a mining environment and the lessons learned, the process of conducting site investigation and the necessary laboratory testing together with machine selection and performance estimation for TBM use III mine development.

Jan 1, 1997

By Thomas C. Wilder, Firoze E. Katrak

As part of a survey on the long range supply of gallium, a comprehensive review of the chemistry of commercial gallium extraction was undertaken Owing to its very small concentration in all commercial minerals, gallium can be produced economically only as a by-product of major extraction processes for other materials. A summary is presented for the chemistry of gallium extraction from many of these process streams included are several procedures for gallium recovery from bauxite, currently the most prevalent source Other processes described are from waste streams from the production of zinc, phosphorus from phosphates, aluminum from kaolin clays, and from coal ash, the largest potential resource A brief review of development of solvent extraction as a unit process for gallium recovery is also presented

Jan 1, 1983

By A. Davis, K. Nelson, C. Webb

Abandoned mines in parts of the Black Hills of South Dakota have the potential for acid rock drainage. For this work, ten sites were examined on Black Hills National Forest land or on private land whose drainage could affect Forest Service land. Water samples from all the sites had pH values less than 6. Results of analyses from water samples and rock samples showed a correlation between metals content and pH. Acid-base accounting was used to determine acid drainage potential of the sites. One site (King of the West Mine) had a high potential for acid generation; fortunately, little or no surface runoff leaves the mine site. Six sites appeared to have moderate potential, including the Minnesota Ridge Mine, which currently is being remediated. Three of the sites had low acid drainage potential.

Jan 1, 2004

By Shigeru Sarata

Working places in underground mines are formed by digging. The main feature of underground working places is that they are surrounded by rock. Digging through rock, which is main operation of mining, generates great reacting force. In many cases, supports are required to maintain a roof. Working places change their location with progress of mining operation. Therefore, for automate the work in such environment, a locomotive mechanism which can endure great reacting force, can support effectively the roof and floor, and has high moving performance in rough environment, might be required. In narrow underground environment which is surrounded by rock, it is possible to generate great fixing force by means of a jack which is set between the roof and floor or both side wall it is usual to apply a jack as anchor post for fixing machinery or reacting force. Self advancing supports widely used in long wall faces in coal mines could be said an example of locomotive mechanism with propping up fixing method. However it is difficult to say that ordinary self advancing supports have enough adaptability for various condition of the roof and floor. New locomotive method for underground working place 'Swing Phase Locomotion' is proposed. It is achieved by mechanism based on frame type support and synchronous control of jacks. Furthermore, to achieved high adaptability to various conditions of the roof and floor, another walking mechanism has been developed. The mechanism employs propping up jack as its legs.

Jan 1, 1989

By R. D. Doepker, P. L. Drake

The dissolution of metals from various metal- mine tailings has been studied through a series of submerged tailings batch tests at US Bureau of Mines laboratories. Tailings selected for this study included both reactive (as determined by column leaching studies) and benign tailings. Metal mobilization in aerated (97% saturated with oxygen) samples appeared to be consistently greater than metal dissolution from stagnant (79% or 70% saturated with oxygen) waters. In the early weeks of the study, sulfate concentrations increased with solid-liquid contact time, while calcium dissolution remained early constant. Metal concentrations varied in relation to solid-liquid contact time and aeration. Leachate pH appeared to be nearly independent of solid-liquid contact time for basic tailings. Reactive tailings having both a submerged and a surface component demonstrated increased metal mobility.

Jan 1, 1991

By L. Gertsch, R. Gustafson, J. Rostami, C. Swope

Development of a permanent human base on the moon for exploration requires a self-sustaining system. Such a system entails the production and processing of limited amounts of raw material on the moon. Any mining and construction activities on the moon can only be performed by a robust excavation machine that can excavate a variety of material, from loose surface regolith to consolidated (frozen) regolith with embedded rocks in the mixture. Meanwhile, a limited amount of information on lunar regolith is available to develop and optimize a machine for lunar ground conditions. Therefore, any excavator designed for use on the lunar surface should have the ability to adapt to a wide range of operating conditions. A prototype cutterhead for the lunar excavator was built and tested at the Kennametal facility in Latrobe, PA. This paper discusses the results of initial material characterization, as well as full-scale tests of a prototype cutterhead in relevant material. A brief review of anticipated production rates under various assumed ground conditions is also presented.

Jan 1, 2010