Search Documents

By K. Oraee

The empirical rock failure criteria play an important role in predicting the mechanical behavior of rocks, since affecting parameters on the behavioral properties of rocks are complex and numerous. Usually the empirical failure criteria are obtained by statistical methods, namely by means of fitting the mathematical function onto the experimental data. For evaluation and verification of the results, however, the quality and accuracy of the fit must be considered. This paper studies the efficiency and accuracy of conventional empirical rock failure criteria using a new approach, which is based on the analysis of uncertainty amplitude on the constant parameters of each criterion. The approach adopted here, is based on the combination of some parameters such as Mean Squared Error (MSE), Root Mean Squared Error (RMSE), type of function, degree of freedom and the confidence level of constants. Correlation coefficient (R2) is then a comprehensive test and can be used effectively for comparison and accuracy of empirical rock failure criteria.

Jan 1, 2012

By M. Javier

Management is a major part of sustainability research. Many different aspects of sustainability have already received significant research attention, but the management processes in mining from the perspective of their impact on society are less understood and integrated as a holistic frame. It is evident that mining technology has received major blame in past ecological disasters and major mining-induced environmental hazards, but the management-mining process has escaped unscathed. This should not have happened. Instead, the management processes should share equal blame with obsolete technology for the failure to identify and monitor potential environmental hazards before their inception of mining. We will present an emergent style of management for the future of mining. It challenges the actual ?mind-set? of mining management. It describes balance and equilibrium: physical, chemical, and biological in nature as an understanding of nature?s language, which is Geomimic along side ?the bottom line?. The goal is to minimize loss instead of maximize profits (waste design) at the design stage of mining and to develop clean technologies (nature's values) to achieve non-social environmental impacts that provide a prosperous legacy to future generations.

Jan 1, 2010

Several economic factors have caused the surface mining industry to require large-capacity shovels and trucks for efficient, high-production, low-cost operations. Some of those factors include technological advancements in equipment, commodity market depressions, increased labor and maintenance costs, contractural obligations and harsh operating conditions. The difficult operating conditions in surface mines, however, pose challenges to the use of high-capacity equipment. They include space limitations, weak over-burden, and weathered soils and rocks. So mining companies face major challenges in selecting appropriate shovels to meet the technical, operating, safety, environmental and economic requirements of their mines.

Jan 1, 2003

By R. G. Reddy

Solid state reduction of roast movat chromite ore with carbon was carried out as a function of C/FeO ratio and temperature in the range 800°C to 900°C by thermogravimetry analysis (TGA). A two stage mechanism, (1) the reduction of FeO present in Roast Movat with carbon monoxide; and (2) the regeneration of CO by the oxidation of carbon with CO2 was proposed. The rate controlling step is the carbon oxidation reaction. A kinetic equation, that of random nucleation, was proposed. The activation energy for the reduction was determined to be 55800 J/mole and is compared to those activation energies determined for other chromite ores.

Jan 1, 1998

By Peter Kowalczyk

Magnetic surveying and map production is well established in land based mineral exploration. Magnetic data are routinely used to map geology in covered terrains, to estimate the depth to basement in overburden covered areas, and to identify altered zones, mineralization, bedding attitudes, and fault networks both regionally in map view, and through interpretation to depth in 3D. Best practices for magnetic survey methods and magnetic interpretation exist in all areas of land based geophysical survey methodology - mineral exploration, hydrocarbon exploration, geological mapping, archeological mapping, and in military applications. At sea, and particularly under the sea, sophisticated magnetic surveys are being done, but it can be argued that these are primarily in niche applications, for example in naval mine-hunting and UXO applications. Magnetic data is not normally collected on AUVs and ROVs conducting mapping and hydrographic survey operations. OFG has developed physical and mathematical calibration routines so that magnetometers can be mounted directly onto AUV and ROV bodies where significant heading errors and magnetic gradients exist. This simplifies the routine deployment of magnetometers on AUVs and ROVs for mineral exploration and other magnetic survey applications without the need for towed bodies, ungainly mounting frames, or degaussing of the survey equipment. Our experience shows that magnetometers can be operated routinely on AUVs and ROVs and that with careful processing useful maps can be produced routinely at low cost.

Sep 1, 2014

By Robert G. Woolery

Union Carbide_ began looking seriously at heap leaching in 1971. At that time some 1.6 million tons of mineral averaging 0.040% U308 were stockpiled at various sites around the Gas Hills, Wyoming, uranium facility. Several alternatives for economically exploiting these reserves were considered and heap leaching seemed the most attractive. At the time, Western Nuclear Inc. was operating a heap leach project nearby in which the low-grade ore was leached with sulfuric acid, the product liquor treated in an on-site solvent extraction circuit, and the stripped product liquor re-acidified and recycled. They were most generous in allowing us to visit their site, answering our questions, and were helpful in discussing the problems associated with heap leaching. They confirmed our belief that, it was possible to operate a heap leach profitably on material too low grade for. conventional milling. Based largely on what we had learned from Western Nuclear's experience, a program was set up involving a laboratory study to determine the characteristics of the mineral stockpiles as related to heap leaching and to conduct a pilot heap leach adjoining our Gas Hills mill. Basically, the pilot heap construction and leach procedure were similar to those described in the literature(1,2) with certain modifications to permit detailed monitoring of the operation. In May, '1972, the decision was made to construct a test heap. The UCC plant at Gas Hills, Wyoming was selected as the most appropriate site for the follow¬ing reasons:

Jan 1, 1977

By Van Price

Some technical developments of the National Uranium Resource Evaluation Program which are of general application in geochemical exploration are being studied. Results of stream water and suspended and bottom sediment analyses are compared for an area near Williamsport, Pennsylvania. Variations of uranium content of water samples with time in the North Carolina Piedmont are seen to correlate with rainfall. Ground water samples from coastal and piedmont areas were analyzed for helium. All media sampled provide useful information when properly analyzed and interpreted as part of a total geological analysis of an area.

Jan 1, 1979

By Leland L. Mink

Open-pit mining is sometimes conducted in areas where the artesian pressures contained in aquifers underlying the pit's floor are great enough to cause floor heave. In order to reduce this pressure several methods are commonly used. One of these methods is a pressure relief well or depressurization wick. The wick consists of a borehole which is filled with gravel and cased at the surface. The wick is allowed to flow freely, thus reducing pressure near its location. The spacing and depth of these wicks can be determined by a simple analytical and graphical technique which considers the weight of material overlying the aquifer and the artesian force within the aquifer. An example of the technique using data from a Colombian coal mine is presented.

Jan 1, 1986

By August E. Vandale

I speak to you today on the subject assigned to me, "Subsidence - a Real or Imaginary Problem", as a representative of Consolidation Coal Company (a wholly owned subsidiary of Continental Oil Company). The information I relate to you is our experience in the Pittsburgh Coal Company Division of Consol and covers the Pennsylvania properties and mines with particular emphasis on the mines in the south- western portion of the State or in the immediate vicinity of Pittsburgh, Pa. Mining of Freeport and Pittsburgh seams of coal in the Pittsburgh vicinity dates back over one hundred years. Consol, or its predecessor, Pittsburgh Coal Company, has been actively engaged in mining in the area since Pittsburgh Coal Company was organized in 1900. Pittsburgh, Pennsylvania came into prominence as the Steel City largely because of the vast reserves of high grade metallurgical coal readily available in the immediate vicinity and also because of its favorable river transportation. Early in the 1900's we operated over 100 small coal mines, with operations located in the Counties of Allegheny, Fayette, Washington, Westmoreland. We have also operated mines in Somerset and Greene Counties. Titles in Pennsylvania can be in three estates: (1) title in fee, (2) title to the mineral, (3) mining rights permitting the removal and extraction of the mineral with or without waiver of surface damage. Consol has over the years acquired good legal title to the coal lands purchased from individual farm owners, with good broad mining rights, and in 98% or more of its title has a complete waiver of surface damage or the right to subside the surface land. In the early days of our Company, individual coal farms were purchased from land owners. Many of these titles severed the coal estate from the in fee title and good mining rights with waiver of surface were conveyed in the original severance deed. Thus, minable coal reserves were put together by the purchase of the coal under many individual farms in an area. In the early years, the mines practiced hand dug mining - later going to mechanical cutting with hand loading of the coal. Systems used were entry driving with room and rib panels. We have practiced full recovery mining as far as practical during the years of hand loading, as well as in the later years when the mines were mechanized. Mining system layouts, methods and procedures have changed from time to time to keep pace with improved mining machinery and new inovations, such as roof bolting and rubber tired haulage.

Jan 1, 1967

By D. Loring, J. Almgren

Climax Molybdenum Company’s Henderson Mine is a large panel caving molybdenum mine located about 43 miles west of Denver, Colorado. Three Joy M120-72-880 fans are installed in parallel on the No. 1 exhaust shaft. Throughout the mine’s history, ventilation changes such as the completion of the No. 5 exhaust shaft have decreased the utilization of these fans. To optimize fan performance they have been run with the full complement of 16 blades, down to as few as four blades. Since the completion of ventilation upgrades associated with the Henderson 2000 project, one surface fan has been operated under normal conditions with 10 or 12 blades. With the completion of a new network model of the Henderson ventilation system, a tool was built to develop fan curves for possible future fan configurations and predict future fan performance. This paper describes the tool and its use at Henderson.

Jan 1, 2007

By I. K. Choi

In a recent paper by Smith and Wen(1) the adsorption of sodium dodecylsulfate and trimethyldodecylammonium chloride on kaolinite was studied. As would be expected considering the general negative character of kaolinite, except perhaps at quite' acid pH values (2,3,4), it was found that trimethyldodecylammonium chloride adsorbed strongly on kaolinite at basic pH values. Furthermore, it was found that sodium dodecylsulfate adsorbed strongly on kaolinite at acid pH values, particularly at initial 1H values below pH 3 (final pH values near pH 4). It is interesting to note that adsorption of the anionic surfactant was strong under conditions where the kaolinite was apparently slightly negatively charged (2). The present paper reports on an extension of the work by Smith and Wen. In this paper the effects of the presence of dodecyl alcohol and sodium hexametaphosphate on adsorption of sodium dodecylsulfate and trimethyldodecylammonium chloride on kaolinite are considered.

Jan 1, 1967

By David Hartley

United States Steel Corporation Minntac Mine is located at Mt. Iron, Minnesota, on the Mesabi Iron Range. The taconite pit is two miles long by a mile wide, with a maximum depth of 170 feet. This paper will deal with the radio remote control of locomotives engaged in the railroad haulage of crude ore and waste rock at this property.

Jan 1, 1970

By C. D. Elifrits, N. B. Aughenbaugh

Introduction Federal and state laws enacted to regulate coal mining and the accompanying public concern about the adverse effects that mining might have on land use have focused much attention on the subsidence of the land surfaces over underground mines. Some questions asked are: • Will abandoned mines subside in the future even though they have exhibited no surface adjustment to date? • If so, when will subsidence take place? • Can a specific surface area be affected by subsidence more than once? • What surface form will the subsidence feature take? • Is there any way to predict when subsidence will occur and end? An attempt is made here to address these questions insofar as it is possible with available data and experience of evaluation of subcritical extraction conditions. Mining that results in subsidence features can be classified as supercritical, subcritical, and critical with respect to the minimum span lengths of the worked-out rooms (Fig. 1). A complete basin will not develop fully immediately over subcritical conditions because the span lengths of the entries are less than the critical dimension (Wardell, 1983). Passageways, entries, and room-and-pillar panels are all included in the subcritical category. Because of the short span lengths, subcritical mining conditions tend to be stable over the life of the mine unless adverse geologic conditions exist (Gray et al., 1974; Dunrud, 1976). Various roof control and support procedures are employed to maintain entry stability during mining. Little information exists concerning the time factor of subsidence over areas of subcritical extraction. Data that have been collected relate to longwall mines, whereby the cavity sizes are designed large enough to induce caving behind the working faces so that complete subsidence at the surface occurs within a short period of time. The UK's National Coal Board (1975) has reduced the enormous amount of data it has collected to empirical correlations and has published these correlations in its Subsidence Engineers Handbook. The handbook states that "None of the foregoing remarks applies to pillar and stall working," with respect to the section discussing the time factor of subsidence caused by longwall mining (National Coal Board, 1975, p. 40). To understand and evaluate how time relates to subsidence above room-and-pillar mines, one must first recognize how mine cavities deteriorate and fail. The propagation of failure to the surface must then be studied, and, finally, the failures that are manifest at the surface in the form of depressions accompanied by both compressional and tensional movements must be investigated. Failure of mine cavities Any cavity beneath the earth's surface represents a condition of nonequilibrium and tends to close with time. Failure of cavities in a subcritical mine can be classified as failure of the roof, failure of the floor, failure of the supports (pillars, cribs), and elastic rebound of the rock. One mode of failure may dominate, but generally combinations of the four will occur. Also, initial instability of geologic materials and structural features and in situ stress may be unknown factors that can contribute to cavity failure. Roof failure is the most obvious opening stability problem in most operating mines. The bridging capabilities of the roof rock are dependent on the rock's material strength, geologic discontinuities, and reaction to humidity changes in the air of the mine. This type of failure may vary in magnitude from gradual flaking to massive roof falls. Mine floor instability can be manifest in the form of a general heave over a broad area or of individual pillar punching. The weaker and thicker the immediate floor material, the more prone a mine is to experience floor problems. Water seeping into an area can soften the underclay, reduce its bearing capacity, and precipitate failure of support for the overburden.

Jan 8, 1986

The 29th annual American Mining Hall of Fame Awards Banquet and Fundraiser sponsored by the Mining Foundation of the Southwest (MFSW) will be held at the JW Marriott Star Pass Resort, Tucson, AZ on Saturday, Dec. 3, 2011. Each year, one living inductee, two recipients of Medals of Merit, and up to five honorees from mining history are chosen by the MFSW for their outstanding contributions to the mining industry. Chilean Minister of Public Works and former Minister of Mining, Laurence Golborne Riveros will be the guest of honor, featured speaker and inductee into the American Mining Hall of Fame. Golborne Riveros was instrumental in managing the rescue of the 33 Chilean miners in October 2010 and in the coordination/management of the ?townsite? for family members, rescue support and the media. His engineering background and executive management skills made him ideally suited to assist in both a technical and managerial role in this emergency.

Jan 1, 2011

By L. G. Closs

Gold continued to be the primary focus of minerals exploration worldwide during 1995. Other targets, though, included primary diamonds and base metals, especially copper deposits amenable to solvent-extraction/electrowinning (SX/EW) processing. The discovery of nickel, copper and cobalt at Voisey Bay in Labrador, Canada was an unusual surprise. Meanwhile, exploration geochemistry continues to evolve to meet new challenges. The major event in this category during 1995 was the17th International Geochemical Exploration Symposium (IGES) held in Townsville, Queensland, Australia in May. The meeting was sponsored by the Association of Exploration Geochemists, which celebrated its 25thanniversary of service to the mineral industry, and the Economic Geology Research Unit of James Cook University, Townsville.

Jan 1, 1996

By Thomas N. Walthier

This paper will review world trends that are increasingly restrictive of mineral exploration and mining throughout the Free World This is occurring in the face of projected huge increases in demand for mineral products Some of the impediments are direct and absolute; others are indirect, but nevertheless effective; still others represent merely hostile attitudes Many of the world governments have a reputation for lack of integrity in dealing with existing foreign investments within their borders, and consequently are quite uninviting places for new investments, especially in the capital intensive natural resources industry. Compared with even 35 odd years ago (and pre-World War II is not that long ago) there are few places left where private mining investments are both wanted and where investors are willing, to go. We shall begin with an analysis of conditions in the U. S., shift to neighboring Canada and Flexico, and then have a look around the world. As the world grows smaller for the private mining sector, the function of exploration, development, and operation is passing over to government. We'll conclude with a view of what this holds for the future

Jan 1, 1976

By N. A. Abdel-Khalek

The objective of this investigation was to compare the results of counter-current flotation column versus conventional flotation cell for the cleaning of a sulphur ore and its discrete size fractions. The tests were carried out using diesel oil as a collector and alcohol as a frother. Generally, flotation column produced concentrates of higher grade. For example, the grade of a rougher concentrate for a given feed obtained with the column increased by 33% higher than that produced with the flotation cell. Such higher grade could not be obtained using conventional cell even after 3 cleaning stages. Moreover, the column gave superior results for flotation of fine and ultrafine particles.

Jan 1, 1991

By James W. Derrick

General widespread interest in fine coal cleaning circuits did not occur in the United States until the mid 1960's. Up until this period the relatively low price for which bituminous coal was sold did not justify for many operators the capital and maintenance costs associated with the beneficiation and drying of fine coal. However, with current growing interest in this area, the introduction of new types of process equipment along with modifications to existing components is occuring to maximize the recovery of coal fines. In 1973 Derrick Manufacturing Corporation introduced high frequency screening machinery into the coal industry. The first design consisted of a 4 ft. wide 18 ft. long single deck screen frame with three 100 mesh woven wire screen surfaces divided by repulping troughs for the addition of wash water. In addition, a special slotted rubber dewatering deck was installed on the discharge end of the unit to assure adequate dewatering of the screen oversize. This panel had nominal 25 mesh X 3.0" slotted openings. The machine was also equipped with a special high speed-low amplitude (3600 RPM .032" % AMP.) integral vibrator.

Jan 1, 1983

By Robert J. Timko, Charles D. Taylor, Edward D. Thimons, Tom Mal

A test system was developed for measuring airflow in the National Institute for Occupational Safety and Health (NIOSH) ventilation gallery using a three-axis ultrasonic anemometer. The gallery was used to simulate face airflow conditions in underground mines having a blowing curtain. Airflow data collected at multiple sampling locations between the face and the end of the curtain were used to draw airflow profiles for different curtain setback distances, intake flow quantities and entry widths. In addition, methane was released at the face, measured at the sampling locations, and displayed as methane distribution in the area between the curtain and the face. Entry geometry had a significant effect on airflow patterns, and the flow patterns affected the distribution of methane in the entry. Flow measured at and parallel to the face was a good predictor of methane dilution and removal within two feet of the face.

Jan 1, 2005

By M. S. Moats

In the 1990?s, Técnicas Reunidas developed the Modified ZINCEX® Process to recover zinc from ores and secondary materials. The heart of this process was the use of solvent extraction to produce purified zinc electrolyte instead of traditional zinc dust cementation. This development was commercialized by Reunion Mining and Anglo American for primary ore at the Skorpion mine in Namibia with the first SHG zinc produced in May 2003. Horsehead Corporation through Horsehead Metal Products, Inc., its wholly owned subsidiary, is presently commercializing the MZP for the treatment of Waelz oxide. This paper will review open source information about the lessons learned and process modifications that have occurred at Skorpion over the past decade. It will also provide an update on Horsehead?s facility being constructed in Rutherford County, North Carolina.

Feb 23, 2014