Search Documents

By Celeste Powell

Liquid carbon dioxide can be used as a replacement for organic solvents in the extraction of anionic PGM complexes from an aqueous phase. This can be achieved only if highly carbon dioxide-soluble chelating agents are developed because conventional chelating agent-metal complexes, such as trioctylamine-gold chloride, are not soluble in liquid carbon dioxide (although trioctylamine is CO,-soluble). Our novel CO,-soluble chelating agents have a fluorinated tail and a conventional amine head group. Both the chelating agent and the chelating agent-metal complex are soluble at ambient temperature at pressures between 7-35 MPa. Equilibrium constants in the 105 range have been measured (in Freon 113, a low pressure screening liquid for carbon dioxide), indicating that these compounds will strongly bind the metal chloride. For example, 93% of Pt-chloride was extracted into Freon 113 using a 3.5:1I ratio of a double-tailed fluoroalkyl amine chelating:metal chloride. 88% recovery of Pt-chloride into liquid carbon dioxide was achieved using the same chelating agent at a 3.5:1 ratio.

Jan 1, 1999

By R. W. Fedors, S. T. Green, R. A. Hart, D. B. Walter

Computational fluid dynamic (CFD) modeling of a potential nuclear waste repository drift may be an important tool to estimate moisture redistribution caused by natural convection within the drift. To refine and support CFD techniques, a small laboratory cold-trap experiment was developed. Results from numerical modeling of the laboratory experiment show the sensitivity of the bulk air flow rate and average air temperature within the drift to several key parameters, including various boundary condition assumptions and surrounding porous media properties.

Jan 1, 2004

By Derek J. Penrice

The Caltrain Downtown Extension (DTX) project will extend commuter and future statewide high-speed rail service into the Transbay Transit Center, which will be located in the business district in downtown San Francisco. The DTX project includes 1.5 miles of underground construction, comprising complex sections of mined and cut-and-cover tunnel. As part of the DTX preliminary engineering process, development of appropriate contracting practices, including contract packaging, procurement methods and contract terms for the underground construction, has been initiated. This paper provides a summary of the evaluations undertaken, preliminary conclusions reached, and proposed next steps to promote industry interest and maximize bid competition.

By William J. Robinson

What is the cummulative rate of recovery of copper from a sulfide leach dump? This is one of the most frequently asked questions today. We, in the industry, ask it of each other when we meet; however, the technical answers may vary from "I don't know" to 'quite good" from people within the same company. Management also poses this question because it plays a vital role in our planning for future production. The answer is difficult because of the many variables between different operations such as physical construction of the dump, topography of the original site, characteristics of dump material, mineralization, water application, etc. Each has a bearing on the rate of recovery. OPERATIONAL DATA Our method of water distribution is unique in that each dump is drilled to allow physical injection of water into the dump. The in¬jection holes are drilled vertically, on 251 centers, from the surface of the dump. Normally, the holes are drilled 40' deep and cased with 4" PVC perforated pipe.. The pipe is perforated at one-foot intervals with four V diameter holes at 901 spacing on the pipe circumference. We formerly alternated shallow holes (20'-40') with deep holes (80'-l80') in an effort to cover the entire dump and hasten oxidation. The shallow hole depth varied according to the compaction thickness. The deep hole depth varied according to the height of the dump and the original ground profile, We prefer to have the deep holes end 20'-30' above the original ground level. This generally allows us to penetrate the coarse material at the bottom of the dump. We had to discontinue the deep holes_ in order to cover more dump area in a shorter period of time to meet increased production requirements.

Jan 1, 1972

By Christian F. Baiz

The author will present a discussion of the steps which must be taken by the prospective developer of a small mining operation to establish technical credibility when seeking financial backing. Particular emphasis will be given to the differing levels of technical work (and their relative cost) which must be accomplished to supply the information necessary to satisfy potential investor groups, whether they be other mining companies, equity investors, or financial institutions such as venture capital firms or commercial banks.

Jan 1, 1981

By Chee Theng

"So many talks, so little time.One of the toughest challenges associated with attending the SME Annual Conference and Expo is deciding how to allocate one’s resources. After accounting for keynote and plenary sessions, committee meetings, networking events, luncheons and exhibits, attending even one of the 109 technical sessions and more than 600 technical paper presentations can be a labor of love. Many, however, managed to make it to many of the sessions, including the mineral and metallurgical processing technical session on solvent extraction, ion exchange and electrowinning.At one point, that room was seated to near capacity, with a considerable number of the audience members standing by the walls at the back. Brittany Valera of Freeport-McMoRan Inc. was one who came early and enjoyed the session in its entirety. "Everything was pretty exciting," she said. "I really liked the modular plants. I think the future of mining, just like what we talked about in there, lies in thinking about things like remote locations, lifetimes of plants, anything that would be reusable and sustainable; and lower-cost and user-friendly would be really beneficial."Michael Moats, associate professor of metallurgical engineering at Missouri University of Science and Technology, started off the session by presenting on behalf of post-doctoral student Alex Luyima, who, like many before him, had been snapped up by industry and is now working for a secondary-metals refining company in Texas. Their team studied the nucleation and growth mechanism of copper on stainless steel from synthetic acidified copper sulfate in the absence and presence of chloride ions and three commercial organic additives: Hydrostar 4208, DXG-F7 and Cyquest N-900. Currenttime data were analyzed using known models, with reference to scanning electron microscope images. Good agreement was achieved between the models and SEM micrographs of deposits at a commercially relevant current density of 30 mA/ cm2. The addition of 20 mg/L chloride was found to increase the size and reduce the number of nuclei. The addition of 2.5 mg/L of each additive did not change the mechanism, but all three reduced the size and increased the number of nuclei, leading to more uniform coverage of the substrate with smoother deposits produced in twohour electrowinning experiments. N-900 had the best deposition coverage while DXG-7 was the easiest to dissolve."

Jan 1, 2014

By Qingqing Huang, Aaron Noble

The Mineral & Metallurgical Processing Division (MPD) of the Society for Mining, Metallurgy & Exploration held the first MPD Student Video Contest during the spring of 2021. The event showcased the work of 18 graduate and undergraduate students from several U.S. and international institutions. The contest began in January when students submitted a onepage abstract for judging. Over the next several months, they developed a three-minute video that further explained their research findings. Both the abstract and video were evaluated by a panel of judges, and the top-placing participant was recognized at an MPD virtual event held on June 10.

Sep 13, 2021

The Pogo Mine, near Delta Junction, Alaska is a new 2500 STPD gold operation. The control system of the mine and milling operations are a hybrid of DCS (Distributed Control System) control and PLC (Programming Logic Controller) control. A DeltaV DCS system serves as the main control and operation platform while the PLCs operate a multitude of vendor specific packages. The communication backbone of the DCS system is a hybrid of star and ring fiber optic topology, which provides reliability and flexibility. The communication between the DCS and PLCs is typically facilitated by serial communication. This communication insures the integrity of the whole control system.

Jan 1, 2008

By Thomas J. Kuli, Tim Rape

When a fan or blower breaks down or becomes worn, customers have two choices. They can replace it or they can have it repaired. In the past, replacement was the preferred option, especially when the equipment was severely damaged or worn. Now, however, customers are discovering the benefits of repairing or rebuilding. Even when the cost of repair is more than 60 percent of the cost of a new fan, customers are choosing the repair option. The cost savings can range from 20 percent to 80 percent. In many cases, the quality of the repaired part or component will exceed the quality of the original. This is because repair engineers have an advantage over the original designers. They can see how the existing fan performed — or failed to perform — in a specific application.

Jan 1, 2005

By R. Bhaskar

The control of respirable dust in mines has been given paramount importance due to the health and safety implications associated with fine dust. The understanding of the temporal and spatial behavior of dust has been recognized as essential for increasing the efficiencies of the existing control techniques and for developing new control strategies. Mining-related studies in this area are, in general, limited. They are also mostly experimental. Some mathematical and computer analyses have been attempted. In this paper, first a review of the mathematical studies performed in the last three decades in this area is presented. Second, a mathematical model for analyzing dust flow in mines is proposed. The model takes into account a number of factors affecting dust transport. It incorporates varying dust generation source strengths and dispersion, deposition, and coagulation of dust in mine airways. Finally, application areas for the model are discussed. A computer program based on the mathematical model has been developed. The program will output the dust concentration in the mine atmosphere as a function of time and distance from the source. The amount of dust deposited on the sides, roof, and floor of the airway is also determined.

Jan 1, 1985

By J. Yuan

Ground calcium carbonate (GCC) and chemically precipitated calcium carbonate (PCC) have become important mineral-based commodities in recent years. GCC manufacturing generally requires high purity and high brightness deposits of marble, chalk or limestone as the stone source. PCC usually uses limes made from lesser quality limestone deposits. GCC products have a wide span of particle size, with a d50 size ranging from sub micrometers to as large as several inches such as those used in landscaping. PCC products are typically limited to less than 10 µm (1,250 mesh). Each PCC product has a narrowly distributed size range. GCC and PCC products tend to have higher levels of whiteness com-pared with other traditional filler and extenders, such as kaolin and talc. Published statistics of GCC production volume often vary due to the exclusion of certain size range GCC products. According to Roskill’s latest estimate, world GCC capacity was believed to exceed 56 Mt (62 millionst) during 2004 for all grades.

Jan 1, 2005

By J. Kretschmann

?We have constructed a world in which the potential for high-tech catastrophe is embedded in the fabric of day-to-day life.? (Malcolm Gladwell) The mining industry is a crucial provider for virtually every person?s needs and thus indispensable. Yet, mining is a complex and risky business: plenty of high risk factors can occur and severely affect nature and the miner?s life and health. Especially for small and medium enterprises (SME) risks may also threaten the economic existence of the company. The responsible and sustainable management of a company should thus be based upon the systematic finding and handling of risks or briefly upon an efficient risk management system. Why do we need risk management? Because nobody is perfect and we make mistakes in the normal course of operation.

Jan 1, 2011

By Ted D. Johnson

INTRODUCTION The tailing dam is part of the SOHIO L-Bar Uranium Mine and Mill located about 70.8 kilometers (44 miles) west of Albuquerque in northwestern New Mexico. The dam location is shown on Figure 1. The tailing dam is one of the last upstream method dams permitted in the industry. Design and construction aspects of the project, as well as operation and maintenance considerations, are reviewed herein. Since initial construction, SOHIO Western Mining Company and Woodward-Clyde Consultants have developed several modifications and improvements in the dam's operating and monitoring procedures. This work has been done in coordination with the New Mexico State Engineer's Office and in accordance with recommendations in a report done for the Corps of Engineer's Phase I Dam Inspection Report. Modifications and improvements described should be of particular interest to owners and operators of other tailing dams utilizing the upstream method of deposition. The tailing facility was designed for a 10-year life to provide an ultimate storage capacity of 6 1/2 billion kilograms (7 1/2 million short tons) in an area of about 180 acres. A plan view of the tailing dam is shown on Figure 2. The tailing consists of approximately 75% sand size material and 25% fines (material passing the No. 200 sieve). The tailing dam includes a small earth starter dam with raises of the dam accomplished using tailing deposited by upstream method techniques. The starter dam is a homogeneous embankment about 610 meters (2000 feet) long, a maximum height of 12 meters (40 feet) and 2 1/2:1 (horizontal to vertical) upstream and downstream slopes. The starter dam contains an internal drainage system which includes a near vertical chimney drain connected to horizontal finger drains. A typical section through the maximum height of the starter dam is shown on Figure 3. A small confining dam, approximately 1.6 meters (5 feet) high, is constructed beyond the limits

Jan 1, 1980

By Mustafa Fener, Masoud Rostami, Sair Kahraman, Behnaz Dibavar

Roadheaders are commonly used in coal mines for roadway excavations. The prediction of roadheader performance is necessary for the planning of roadway projects and the estimation of costs. Recently, a new rock mass cuttability classification (RMCC) system has been introduced for roadheaders used in coal mines. In this study, the validity of the RMCC system was investigated for different types of roadheaders and different coal mines. Four different coal mines were visited, and the performance measurements of different axial and transverse roadheaders were carried out during the excavation of roadways. Uniaxial compressive strength, volumetric joint count, the strike and dip of joints, joint aperture, the Cerchar abrasivity index, and water ingress were determined in field and laboratory studies to calculate the RMCC index. The analysis of the data demonstrated that the correlation coefficients between the net cutting rates and the RMCC indices were higher than 0.94, suggesting that the RMCC system was valid. It was concluded that the RMCC system could be reliably used for the evaluation of roadheader performance in coal mines.

Jun 21, 2023

By Jerry Dolph

Hecla Mining's Lucky Friday Mine, located beneath the town of Mullan, ID, has been shaken since the 1960s by many deep underground rock bursts. The largest rock burst carried a magnitude of 3.5 on the Richter Scale. It occurred in 1969 when all of the stopes on a level approached an upper level at the same elevation. After that, a stair-step pattern was used to give the mine's levels more of an "arch." The article is an account of one of the more ferocious bursts to hit the miners of the Lucky Friday. I say "miners" instead of "mine" because I was there and it was a very personal experience for me. I had been working at the Lucky Friday for six years. During that time, I had heard and felt thousands of air blasts. In fact, in the early spring of 1986, the mine was experiencing as many as 1000 air blasts an hour, of different intensi¬ties, of course. Most of them sounded like popcorn popping. There were also a few bumps and occasionally a real boomer. That day did not seem any different

Jan 1, 1994

By Jürg Schlumpf

Concrete is one of the decisive construction materials, also for the AlpTransit Gotthard Tunnel. The client has many requirements, and many are the solution possibilities that concrete systems can offer. Cement producers and concrete admixture manufacturers have been challenged to design and test jointly concrete systems for cast and sprayed concrete. The testing operation followed the scenario laid out by the Gotthard AlpTransit Project management?s instructions ?Testing system for concrete mixes.? Various supplier teams have applied for the concrete systems for sections Amsteg/Erstfeld, section Sedrun and/or sections Bodio/Faido and have also followed through with the tests. As was to be expected, the rate of failed mixes matched the level of the requirements. Thanks to this system, it was nevertheless possible to test complete concrete systems for all sections and to get them approved. The joint ventures tendering for the contracts were allowed to include only approved mix designs in their bids. Workability and durability are of paramount importance for cast and sprayed concrete mixes. Durability is influenced by the chosen mix design where binder concept and well-defined water content, i.e., impermeability, are determinant. Aggregates for AlpTransit are to be considered as given. The concrete mix design also determines workability. Because ambient conditions and also requirements with respect to workability are subjected to change, it is necessary that the mix designs include control measures. The choice and number of components for the concrete systems (cement, additives and admixtures) allow adaptation to changing conditions. For AlpTransit such adaptive measures must meet very strict requirements.

Jan 1, 2008

By J. C. Poulos

The West Elk Mine is located near Somerset, Colorado approximately 70 miles southeast of Grand Junction, Colorado and 72 miles southwest of Glenwood Springs, Colorado on state highway 133 (Figure 1). The West Elk Mine was opened January 20, 1982 as the Mount Gunnison #1 Mine operated by the West Elk Coal Company, a division of ARCO Coal. In the early 1990?s ARCO changed the mine name to West Elk Mine and the operating company was renamed Mountain Coal Company. Arch Coal, Inc. purchased the West Elk Mine in 1998. West Elk Mine has produced coal from three different seams. Coal was first mined from the F Seam, the upper most seam in the stratigraphic sequence, from 1982 through 1991. Coal was produced from the B Seam, the lower most seam, starting with continuous miners in 1991 and transitioning to longwall mining in 1992and continued on through October 2008. The development of the E Seam, which is the middle seam in the stratigraphic column, started in 2004 with longwall production commencing in 2008. The ventilation conversion from exhausting to forcing for the E Seam portion of the West Elk Mine was implemented in late October 2009.

Feb 27, 2013

By J. Finch, R. McIvor

This paper presents the development of a new grinding circuit steady-state modeling system. It is fundamentally based on the “functional performance equation”, which has now been used to improve the performance of numerous grinding circuits. This equation characterizes the two distinct efficiencies that are at work in a ball milling circuit, and how these relate to overall circuit productivity. It does so based on the particle size chosen to distinguish between coarse and fine (product size) material. Now, by applying it to all the material size classes, a simple yet reliable ball mill model was created. Combined with cyclone recoveries, the complete, detailed grinding circuit performance can be exactly reproduced mathematically by the computer program. It can then be used with separate process equipment application engineering methods to systematically engineer grinding circuit improvements. The development, features, uses and limitations of the system are described.

Jan 1, 2007

By D. E. Wolfson

As energy requirements in the United States expand with the growth of the Nation, use of coal also can be expected to increase. This optimistic outlook for the coal industry is based on our vast reserves of high quality coals and the possibility of converting coal to end uses other than electricity and metallurgical coke. Potentially, millions of tons of coal might be needed in the form of gas and liquid fuels to supplement our reserves and imports of these natural products. Exactly when they will enter the economy on a large scale depends on many factors. On January 1, 1960, the estimated remaining reserves of coal were 1-1/2 trillion tons, about 50 percent of which is bituminous coal. In 1965, the production of bituminous coal and lignite passed the 500-million-ton mark, emphasizing the steady upward trend from the recent low of 403 million tons, and if the present rate of increase continues within the next five years, output should pass the alltime high of 631 million tons achieved in 1947.

Jan 1, 1969

By J. Hupka

The limited effectiveness of the original hot water process for recovery of bitumen from certain Utah tar sands containing bitumen of higher viscosity (e.g. Sunnyside, Tar Sand Triangle)1,2 indicated that bitumen viscosity strongly' influences the separation efficiency. In this regard, there should exist a critical value of bitumen viscosity above which the effectiveness of the hot water process decreases significantly. Apparently certain tar sands contain bitumen of such high viscosity that even a digestion temperature of nearly 100°C is insufficient to lower the viscosity below the critical value. In addition it seems that differences in physico-chemical forces which act between sand and bitumen are negligible in comparison to the difference in visco-mechanical forces. Predominantly mechanical forces hold viscous bitumen on the rough surface and in the pores of sand particles, resulting in strong adhesion. This phenomenon is a critical feature in the phase disengagment of oil-wetted domestic tar sands with viscosity control by temperature. Besides increasing the temperature for viscosity control the effectiveness of the original hot water process could be enhanced by control of bitumen viscosity with diluent additions. Strictly speaking this appraoch is the only possibility for heavy bitumen for which the high temperature of digestion does not lower the viscosity sufficiently. As a result of viscosity control by diluent addition the digestion temperature can be lowered which is important from an industrial standpoint. Another important consideration is that effective phase disengagement occurs only when the entire bitumen phase has the same viscosity. This means that some time (penetration time) is necessary for complete and uniform dilution of the bitumen. If the viscosity of bitumen, which is a function of temperature, diluent addition and penetration time, controls the separation efficiency, hot water processing of many different kinds of tar sands should be possible, assuming that the sand phase consists primarily of quartz-type minerals.

Jan 1, 1982