Search Documents

By Gary Jobson

The Mt Todd Gold mine is situated near Katherine in the Northern Territory of Australia. Commissioning of an 8 Mtpa processing facility incorporating a four stage crushing circuit, ball mills, flotation, concentrate regrinding, high rate thickening and CIL processing was commenced during late 1996. A 4.5 M tonne /annum crushing and heap leach facility was commissioned during late 1994, and was subsequently upgraded to a nominal 6 M tonne / annum circuit during 1995. Processing equipment used included primary gyratory, secondary cone and tertiary Barmac VSI crushers. Some of the features of that crushing circuit and heap leach facility were presented at the Randol Perth 95 conference by myself. The location is described as sub tropical with average climatic conditions including 1100 millimetres annual rainfall, predominantly during the December. to March wet season, and 3000 millimetres evaporation and maximum temperatures ranging from around 26 to 46 °C. The main gold occurrence at the Mt Todd site is the Batman deposit, with current published Reserves of some 60 Mt@ 1.20 g Au / tonne ( 0.0425 oz Au / ton ). The primary ore from the Batman deposit is an extremely competent greywacke and is very hard at an average Bond Ball Mill Work Index of26.5 kWhrs/ tonne. Other indicators include a Bond Impact Crush Work Index of 20 kWhrs I tonne, an Abrasion Index of 0.15 and Ultimate Compressive Strength values of 100 - 200 MPa. The main gold occurrence is very finely disseminated free gold (at an average grain size of around 5 micron) within a combination of quartz and mixed sulphide. This gold bearing component is confined to largely parallel veins ranging from 0.5 to 25mm wide within a greywacke matrix. Although the gold is essentially non­refractory, there is a strong recovery versus grindsize relationship due mainly to the liberation characteristics and the relatively low permeability of the host greywacke rock.

Jan 1, 1997

By Young C. Kim

Introduction and Objective of This Paper Computerized open pit mine models* are more and more used today for feasi¬bility studies as well as for long range mine planning. In fact, using these models is becoming an enforced practice due to various reasons. One main reason is its capacity to evaluate several designs in a fraction of time required by manual effort. Another reason is the necessity to evaluate several. pit designs due to ever decreasing grade of the orebody and increasing financial risk due to smaller profitability margin. In spite of today's accepted use of computer models, very little guidelines are available which the average practitioner can follow either to choose or to build the type of model best suited for his need. Consequently, the objectives of this paper are: 1. To review the current state of the art in the computerized open pit mine models. 2. To provide some suggestions for model selection. 3. To share our experiences in developing a model for a highly irregular copper ore deposit (see Appendix).

Jan 1, 1977

By FELIPE SÁNCHEZ, PHILIPP HARTLIEB

Innovation plays a critical role in the mining industry as a tool to improve the efficiency of its processes, to reduce costs, but also to meet the increasing social and environmental concerns among communities and authorities. Technological progress has also been crucial to allow the exploitation of new deposits in more complex scenarios: lower ore grades, extreme weather conditions, deeper deposits, harder rock mass, and high-stress environments. This paper discusses the importance of innovation for the mining industry and describes the mechanisms by which it is carried out. It includes a review of the drivers and actors involved and current trends. The digital transformation process that the industry is going through is analyzed, along with other relevant trends that are likely to shape the mining of the future. Additionally, a case study is presented to illustrate the technical and economic implications of developing a disruptive innovation project.

Jul 23, 2020

By Rossen Halatchev

The production sequence optimization of open pit mine is a procedure that reflects the exploitation conditions over life of mine. These conditions are determined by the geological characteristics of the deposit, requirements of the mining and processing technologies and economic parameters of the exploitation. From a technological point of view the production sequence optimization deals with two aspects - spatial and time. Each of them plays a tremendously important role in searching for the optimum solution of the problem. This paper treats the time aspect of the production sequence optimization. This aspect is revealed in the context of the problem of the working zone formation of the open pit mine in time. The problem formulation places an accent on the determination of the theoretically possible time distribution of the waste and ore quantities of each bench of the open pit mine. A mathematical solution to the problem has been developed based on combinatorial analysis. The solution provides a multi-variant investigation of the production sequencing with the use of an optimization model developed as a linear programming formulation. The model objective function uses the Net Present Value as a criterion for assessing the effectiveness of production sequencing. A case study is provided for the conditions of Assarel copper open pit mine (Bulgaria) to illustrate the applicability of the approach. The results obtained reveal the complex nature of the variation of the Net Present Value as a function of the mining factor.

Jan 1, 2002

By N. K. Bohidar

Evaluation of the stability of a structure under given boundary conditions requires accurate knowledge of the state of stress as well as the mechanism of failure at the critical state of stress. This paper represents a part of the research done by N. K. Bohidar during 1965-1968 for his Ph. D. research in Mining Engineering at the University of Utah. It summarizes the determination of internal stress and failure phenomena around cylindrical openings in viscoelastic media subjected to lateral restraint and vertical uniaxial load. The conditions of lateral restraint and viscoelastic nature of the media represent conditions associated with subsurface openings in rocks. The financial assistance provided to the project from the University of Utah Research (Uniform School Fund), W. C. Browning Scholarship Fund, Earth Science Research Fund, and D. C. Jackling Loan and Scholarship Fund is gratefully acknowledged. The authors also acknowledge the assistance of S. Siugh, W. Jones, and K. McCarter during the project.

Jan 1, 1970

By T. J. Loyd

The capabilities of the analog computer, the Mine Ventilation Simulator, installed at WHA's Safety and Health Technology Center in Denver, Colorado, are discussed. General opera- ting procedures are described showing how a mine model is produced, and how the model can subsequently be modified to produce a solution to a mine ventilation problem. A sample problem is included to illustrate the technique. The important role the Mine Ventilation Simulator plays in ventilation training is discussed, including experiences with the education of students at the Colorado School of Mines. This paper includes a summary of some of the advantages and disadvantages of the analog technique and suggests some design criteria for application to future development of analog computers, based on experience gained with the Mine Ventilation Simulator.

Jan 1, 1984

By Thomas E. Finch

Engineering mine design encompasses a range of situations, and each situation has its own range of detail and fineness. The most time consuming, and perhaps repetitive design situation involves evaluation of new or alternate mining methods. Many man years are consumed examing alternatives conjured up at all levels of the design team, from the number crunching engineer to the engineering manager. Many alternatives are intuitively disregarded, some are briefly evaluated and thrown out, and many others are started but not completed due to time constraints. All alternatives have similar input characteristics and evaluation procedures. In the design process, production requirements are known and equipment production capabilities are generated to determine the numbers and costs of an equipment type required to match a given situation. The end result is some comparative figure, typically cost per ton or yard upon which a decision is built. The similarity of input data and problem solving techniques lends design to computer solution. Computer aided equipment evaluation is not new to the mining industry. An existing and accepted technique is exemplified with the programs used by truck manufacturers. Given a haulage profile and production requirements, the number of anyone capacity, horsepower, tire size, gear ratio or similar characteristically identified truck can be determined. This information can be outputted in varying degrees of complexity and the results used with equally varying percentages of credibility by design or production engineers. Most engineers are willing to accept-the computer's effort with relief and a desire for belief. Although inherently more complex, the ultimate end of computer manipulation should be total mine design. This is an extremely large step in the evolution of mine design, and not many engineers, including the authors, believe the results would be directly applicable or necessarily correct. As with computer simulations of an operation, total computer design of mines requires such complex and lengthy input that each mine might be manually designed more quickly and cheaply. The existence of computer programs which initially evaluate a mining system or part of the system is upon us, however.

Jan 1, 1978

By D. Bahrami, W. K. Asante, G. L. Danko

It is prudent to interpret atmospheric monitoring signals in real time for checking the safe limits of the air conditions in underground mines. In gassy mines, real-time evaluation increases the safety of operations. In all mines, continuous monitoring and evaluation contributes to maintaining air conditions within healthy and safe limits. Signal interpretation for safety conditions in mines is difficult for many reasons. An increase in hazardous contaminant concentrations can be predicted by signal pattern recognition, root cause analysis of rapid changes toward deterioration, and forward prediction in time using algorithms and numerical models. The paper describes an early warning system for analyzing monitored signal patterns continuously in real time as well as forward predicting the various environmental and working conditions to recognize dangerous trends that may affect safety and health in underground mines. A dynamic, numerical ventilation model with heat and gas contaminant simulation components is used for the analysis of atmospheric data. Methods and test results are discussed with numerical examples for signal propagation prediction. Several mine examples are studied using controlled, synthetic data for malfunction simulations to evaluate time delays between the detection time of suspicious signal trends and the time of dangerous threshold crossing marking an accident scenario. Delay time is found in the order of 20 min in the examples, signifying the useful time period for preventive intervention between EWS warning and the likely breakout of a following accident.

By Peter C. Finlayson

Rapidly rising gas and oil prices and the falling quality of coal is forcing energy users in many parts of the world to consider the application of low grade fuel, particularly coal, for steam raising and power generation. However, the use of such low grade coal is normally resisted by the consumer because of operational problems associated with high ash content, sulfur emission and, in some instances, slagging problems caused by low melting temperature constituents in the ash. Recently developed technology involving 'fluidized bed combustion' offers a potential solution to these operational problems. Much of the early work was conducted in Britain, where rig tests were commenced during the early 1960's. This has led on to the successful conversion and operation of a fluidized bed fired industrial boiler at the Renfrew works of Babcock & Wilcox Ltd. Orders for the first commercial boilers incorporating this technology have recently been announced. Significant development work on fluidized combustion is now being undertaken in various parts of the world, in particular North America, Germany and Japan, and the first large scale units are under construction or being commissioned. This paper concentrates on the development of the technology in Britain, outlines the reasons for applying fluidized bed combustion and de-scribes its application at atmospheric pressure for steam raising and at elevated pressure for power generation . Coal Processing Consultants is a Partnership between the National Coal Board and Babcock & Wilcox Ltd. of Britain and has been established in order to provide technical advice and economic evaluations on all aspects of coal processing and utilization. In view of the involvement of its Parents in the development and exploitation of fluidized bed combustion technology, Coal Processing Consultants has been retained by clients in various parts of the world to provide expert advice on the application of fluidized combustion for particular coals and project situations.

Jan 1, 1978

By R. W. Chadwick

Coal was discovered in South Africa in the mid 1830's. The earliest exploitation of modern times was probably in Natal where, in a letter dated 20 August 1842, a Captain Smith mentions that a wagonload of coal brought to Pietermaritzburg, was sold. Until the discovery of diamonds in 1867 and the Witwatersrand gold in 1886, coal mining satisfied a very small domestic demand. By 1889, at least four collieries were operating in the Middelburg-Witbank district, some 120 kilometres East of Johannesburg, and mining had star- ted at Vereeniging, about 50 kilometres to the South of Johannesburg. A map of South Africa is shown in Figure 1 and an enlargement of the main coal mining areas in Figure 2.

Jan 1, 1982

By B. Schimm

Mining of material without blasting and / or selectively becomes more and more important for high quality ROM-products. Surface Miners have been developed especially for this purpose. The cutting technology of these machines has been improved, so that harder material as well as wet and sticky materials can be cut with better results now. Especially the cutting drum design and more precise drum manufacturing process now allow production and equal tool wear over a long period. The better knowledge of rock parameters influencing the cuttability and cutting results allow higher production, less cutting tool wear and therefore reduced production costs.

Jan 1, 1999

By Konner Horton, Adam L. Bedell, Don Del Nero, Brian Jones

"The City of Atlanta’s Water Supply Program Tunnel project includes a 7,315-m (24,000-ft) long, 4-m (13-ft) diameter, hard rock tunnel. A complex aspect of the project involves connecting five, blind bore shafts to the tunnel in a location close to current drinking water reservoirs. During the supplemental geotechnical investigation following the initial contract award, results from additional borehole geophysics were reviewed. Unfavorably oriented fracture sets forced a change in the original pre-excavation grouting program designed for that site. Real-time grout monitoring and geophysical data were compared to provide assurance that the program, as designed, correlated with the in situ ground conditions. Following grouting, results were modeled, and all grouting data were reviewed to determine if grouting was complete.Project backgroundThe current water supply system operated by the city of Atlanta’s Department of Watershed Management (DWM) consists of four, aged, raw-water pipelines, one of which dates back to 1893. Based on previous assessments completed by the DWM, the entire water supply system is at, or will soon reach, its recommended useful life. As such, the city acquired the Bellwood Quarry in 2006 with the intention to create a water storage facility with a volume of approximately 9.1 billion L (2.4 billion gal) to serve approximately 1.2 million people.The project location is shown in Fig. 1, which is generally in the northwest part of downtown Atlanta, GA. The overall project has been divided into two phases. The Phase 1 project connects the quarry and the Hemphill Water Treatment Plant (HWTP), and the Phase 1 Extension project connects the HWTP to the Chattahoochee Water Treatment Plant (CWTP) and the Chattahoochee River. A 7,315- m (24,000-ft) tunnel with a finished diameter of 3 m (10 ft) connects all three elements. The HWTP location is also where the city’s two most proximate drinking water reservoirs are located."

Jan 9, 2018

By W. Jacobi, F. Steinhausler, A. C. James

INTRODUCTION In 1979 the Committee on Radiological Protection and Public Health of the Nuclear Energy Agency (OECD) defined a programme of work needed to improve radon dosimetry and monitoring. A Group of Experts in this field was established by the NEA and at the first meeting of the Group the authors were designated an initial task with the following terms of reference:- To review dosimetry of radon, thoron and their daughters, and in particular:- - to examine analytical models for the assessment of dose to individuals who are exposed to aerosol mixtures of these nuclides; - to examine the state of knowledge of the characteristics of aerosol mixtures of these nuclides and other factors that influence the dose to the lung, and identify those parameters which should be measured for dosimetric purposes in radiological surveillance programmes; - to identify areas where further study or research are needed. In this presentation we attempt to examine, with these objectives, the relationship between exposure to radon and thoron daughter aerosols expressed in terms of the working level month l (WLM), or its SI equivalent, and dose accumulated by sensitive tissues of the lower respiratory tract. Over the past two decades many attempts have been made to calculate the lung dose equivalent to l WLM exposure in mine atmospheres, usually in terms of the maximum dose to basal cells in a small part of the bronchial tree. The calculations have employed variously detailed models of airway anatomy, aerosol deposition, ciliary clearance and dosimetry of tissue at the bronchial surface, and are well reviewed elsewhere (Walsh, 1970; UNSCEAR, 1977; Jacobi, 1977; Fry, 1977). They agree in the conclusion that basal cells in segmental bronchi (between about the third and fifth bronchial generations) receive the highest dose, although estimates of this dose differ by more than an order of magnitude, ranging from about 0.2 to 12 rads per WLM (2 mGy to 120 mGy). The most critical parameters of these models are the assumed depths of basal cells below the bronchial surface and the fraction of the WL carried by free ions. When more realistic values of these parameters are substituted (Jacobi, 1977), the dispersion in calculated maximum doses to basal cells is reduced to give a much smaller range from about 0.3 to 1 rad/WLM (3 to 10 mGy/WLM). The parameters and methods employed in these various models, however, remain too diverse to infer the sensitivity of the dose conversion to practical variations in aerosol characteristics and the additional factors determining lung deposition and clearance. We have therefore taken the approach of developing newer models (Jacobi and Eisfeld, 1980; James et al, 1980) that can encompass the range of available experimental data on the physical and biological behaviour of radon and thoron daughters and also accommodate the different interpretations that can be put upon them. We have paid particular attention to the averaging of dose over tissues of equal sensitivity in the lung

Jan 1, 1981

By D. Scott Barr

The Zarafshan/Newmont Joint Venture operates the Muruntau heap leach project, located in the Kyzylkum desert of central Uzbekistan. The mine produces more than 12.4 t/a (400,000 oz/year) of gold from low-grade oxide ore stockpiles adjacent to the Muruntau open pit. It is op¬erated by the Navoi Mining and Metallurgical Combine and is one of the largest gold resources known (Fig. 1). Since commissioning in 1995, total heap leach production has exceeded 21 t (675,000 oz). The joint venture uses four-stage crushing and screening to produce a final product for heap leaching, Merrill-Crowe processing and local refining.

Jan 1, 1998

By C. I. Wilmot

FMC's Paradise Peak Mine was discovered in July 1983. The deposit at discovery contained 11,340 ,000 tonnes (12,500,000 tons) of ore grading 3.71 glt (0.108 oz/ton) Au and 120 glt (3.5 oz/ton) Ag. A feasibility study was completed by Davy McKee in May 1984, with detailed engineering starting in June 1984. Construction of the facility started on January 2, 1985 with plant start-up taking place on April 14, 1986, two and one half months ahead of schedule and more than 10% under budget. This paper describes the status of the operation approximately 1-1/2 years after start-up including revisions and additions to equipment and process.

Jan 1, 1988

By G. Reed Marchant

During the past two decades, we have witnessed the computer revolution. Like other revolutions, it has been successful in many ways; however, it has not been without difficulties. One of the areas where these difficulties have been more prevalent has been in the application of computers for the purpose of controlling industrial processes. During the early 1960's, many people naively assumed that bridging the gap between data processing and process control was a simple matter of connecting a few wires, doing a little programming, laying off most of the people and watching the plant make great increases in production as the lights on the computer blinked on and off. Unfortunately, it has not been that simple. Instead, a whole new-set of disciplines has been required to overcome the major obstacles that exist. Nevertheless, current successes are proving that the digital process control computer is here to stay, and that through the application of digital computers an attractive return on investment can be obtained in many applications.. The purpose of this paper is to illustrate some of the requirements for successful implementation of computer control systems, with particular attention to the following four objectives: First: Acquaint the reader with the general control problems so that he may more fully recognize the major requirements for successful implementation. Second: To acquaint the reader with the types of control hardware that can be considered for use in the development of control systems. Third: To discuss some of the major obstacles that must be overcome for successful implementation of computer control systems. Fourth: To discuss the systems approach in the development of control systems and to illustrate it in the implementation of an actual control system.

Jan 1, 1971

By R. C. Troxell

Alternative methods of analyzing data acquired by the Morenci copper concentrator process control instrument-computer system are presented. Experimental measures of ore characteristics, for proposed feed forward control, are introduced. These include on-line indexes of ore hardness, ore density, ore dusting, and ore color. Comparison of metallurgical results before and after computerized process control implementation, allowing for differing ore grades, oxidation, hardness, and fineness of grind, also is described.

Jan 1, 1979

By Don L. Deardorff

The Deserado Mine and transportation system is the fuel supply portion of the Bonanza Power Plant project. Deserado Mine con¬sists of an underground mine with a capacity of 1,224,700 tonnes (1,350,000 tons) of clean coal per year, a 649 tonne (715 tons) per hour closed water circuit jig type preparation plant, a 5.6-kilometer (3 ½ -mile) overland conveyor with covered slot storage, a unit train rail load-out and 59.5 kilometers (37 miles) of totally independ¬ent, captive electrified railroad. Planning and exploration started in March of 1978. Construction of all facilities was completed in April of 1984, approximately six years after initial planning was commenced. This paper will discuss exploration, environmental permitting, mine planning, engineering and construction of the Deserado Mine project.

Jan 1, 1984

By R. Larry Grayson

In an interdisciplinary research effort at West Virginia University, the Mine Management Support System (MMSS) is being developed as a window-based shell that may be used for the integration of a myriad of applications software. A number of integral components that focus on enhancing operational decision making are being developed as well. MMSS includes a flexible and robust work scheduling system that assigns the "best," qualified workers to the highest priority jobs on a shift while considering many practical and dynamic parameters affecting the assignments. A consultation system has been developed to help solve operating problems using management-preferred responses and the latest available information on operations.

Jan 1, 1992

By J. A. Marts

Reservoir properties including porosity and permeability distributions in longwall coal mine gobs have direct application to modeling the flow patterns and gas distributions in the gobs. Proper assessment of these distributions is required to assess gob gas hazards such as spontaneous combustion and explosive methane mixtures and to optimize gob gas venthole operation and nitrogen inertization. Determining the reservoir properties is difficult given that the gob is inaccessible and direct measurements cannot be easily taken. Several techniques had been used by previous researchers and will be discussed. This paper will present the methodology used to model the gob compaction by simulating the sequential extraction of coal. Two Western US coal mines were used for case studies. By determining volumetric strain, the porosity and permeability distributions in the gob can be calculated. The geo-mechanical model predicts an axisymmetric volumetric strain distribution with a steeper slope near the start-up room and a shallower slope near the active face.