Search Documents

By SIMON DIAZ-QUEZADA, HUMBERTO ESTAY

The heap-leaching process is widely used for recovering different metals. In Chile, copper production by heap leaching has been accounting for between 30 and 40 percent of annual copper production over the last 10 years. This level of production has been achieved through and supported by the use of a mathematical relation known as the leaching ratio (LR), which correlates operational parameters with metal extraction in a heap-leaching operation. In spite of the widespread industrial use of this relation, few scientific studies mention it. This disparity between industrial practice and scientific research could lead to operational decisions that lack substantial theoretical support and to scientific studies with limited industrial impact. This study describes the LR and its current uses and limitations.

By Ziyan Ouyang, Haotian Zheng, Spencer Quiel, Mike Mooney, Clay Naito

This paper summarizes the results of an experimental program conducted to characterize the moment-rotation behavior of skewed flat radial joints from large diameter (45 ft) tunnel lining. Both positive and negative joint moment-rotation behaviors were measured experimentally using two-segment joint combination assemblies. The results are compared to closed form methodologies used by designers, e.g., the Janssen method. The differences in observed and model behavior are discussed within the context of design practice.

Jun 23, 2024

By Robert E. Kirby

The potash mine and refinery of AMAX Chemical Corporation is located 26 miles east of Carlsbad on the north end of the potash producing areas. This property was developed between 1949-1952 and production of muriate began in August 1952. Two shafts, located 400 feet apart, were sunk to the ore zone 900 feet below the surface. A 15-foot diameter ore hoisting shaft equipped with a 1000-ton ore pocket, crusher and automatic skip loading equipment plus a 20-foot diameter service shaft with a curtain wall for exhausting air were provided. Sylvinite production to date has been from the first ore zone, stratigraphically, the lowest of ten identified mineralized zones in the salt section. This first ore zone has been the top producer of Muriate of Potash over the years. In our area we do have some very marginal mineralization in the third ore zone some 35 feet above the first. We have not mined from this seam as yet but we are investigating the economics very closely with access slopes and an experimental mining panel. Our ore seam is generally flat lying but does have local gentle rolling with grades from 2% to 5%. The mine was designed and developed from the beginning with conventional mining practices and rail haulage from the mining section to the ore pocket. As mining progressed in the early years, production increased from less than one million tons annually to a maximum of 3,935,000 tons in 1964. Efficiency also kept pace with the increasing production and continually improved until the efficiency of the production crews reached an average of 100.3 tons per manshift in 1964.

Jan 1, 1974

By A. Bruynesteyn

Most ores and coals contain sulphide minerals such as pyrite, FeS2, the sulphur portion of which is a ready substrate for a variety of sulphur oxidizing bacteria. Although there are several bacteria capable of oxidizing sulphide minerals, the most often discussed culprit is Thiobacillus ferrooxidans.. Oxygen from the air slowly oxidizes pyrite into sulphuric acid, but T- ferrooxidans can increase this reaction rate several 100,000 times.

Jan 1, 1991

By C. Hansen, J. Killey

This paper discusses the replacement of AEROFLOAT ® 1 25 promoter by AERO ® 5688 promoter at Sonora Mining Corp.'s California Mother Lode concentrator. Flotation concentrate is trucked 120 miles to a leach plant in Nevada, so the reduced mass resulting from higher gold grades and reduced talceous gangue and barren pyrite resulting from this change in promoters has brought about a major decrease in shipping costs. Preliminary laboratory testing indicated that free milling gold and controlled amounts of pyrite could be floated using Aero 5688 promoter with reduced dosages of Aero 350 xanthate.2 Extensive plant trials confirmed that the new reagent suite could indeed maintain gold recoveries while reducing total mass. Improved froth characteristics also improved operating flexibility in treating various ore types, and overall reagent costs have been reduced.

Jan 1, 1991

By M. Pillay

INTRODUCTION Heat stress continues to be a safety concern in underground mining. This is due to a number of reasons including increasing depths of mining, increased levels of heat generated from machines, ventilation systems being constrained from providing suitable levels of airflow and others. In order to assess if a thermal environment is safe for miners under normal or modified work arrangements, or to specify stop work conditions a heat stress index is used to guide decisions. Historically, a number of heat stress indices have been developed and applied in underground mines. These can be classed under three broad headings; single measurement, empirically based and rational indices. Do any of these indices perform better than the others? Which one allows simple determinations and decisions to be made in the mine? This paper aims to provide answers to these questions by comparing and contrasting three indices; effective temperature (ET), simple air cooling power (ACP) and Thermal work limit (TWL) for a range of typical mining wet and dry bulb combinations? The paper concludes with the identification of areas for future research. BACKGROUND Heat stress causes discomfort, increases physiological strain, decreases productivity and performance, and contributes to increased incidents [1]. Effective management and control of heat stress is particularly important in mining where hot working conditions are very common [2]. Heat stress index is a common indicator that is used by mine safety advisors and managers to guide decisions about safe work practices in mining under normal or modified conditions. According to Howes and Nixon [3] A safe heat stress control strategy for an underground mine has three elements: • Application of an environmental measure which reflects physiological strain with sufficient accuracy for the range of conditions encountered underground. • Acceptance of a functional relationship between the environmental measure and human performance which is used to optimise the environmental conditions achievable with either ventilation or ventilation and refrigeration. • A management control strategy based on the environmental measure which is designed to ensure that work in environments where excessive physiological strain may occur is prevented and corrective action is initiated. The link between these elements is an environmental measure that reflects the physiological strain a worker is subjected to. Since the turn of the twentieth century various indices of thermal stress have been developed (McPherson [4], Howes and Nixon [3], Brake [5]). In selecting a suitable environmental measure or index one problem that must be addressed is the ease with which it can be physically obtained relative to it accurately reflecting the physiological strain. No index can be universally applied and there is no single correct measure or index. However if an index has provided adequate control in a particular circumstance, then it can be regarded as correct for that situation.

Jan 1, 2019

By D. Bleazard

Barrick Goldstrike Mines, Inc. is actively involved in improving the reliability of mining and processing equipment through the use of failure analysis and condition monitoring activities. Program results include an increase in equipment capacity and an overall reduction in operating costs. The identification of equipment failure modes and the development of associated capital asset management practices can minimize failure consequences. Successful programs have included; alterations to management practices, equipment modifications, and/or the implementation of condition monitoring programs. By controlling or minimizing the effects of incipient equipment failures, corrective actions can be taken earlier in the failure cycle, resulting in an associated reduction to repair costs and equipment down time.

Jan 1, 1997

By D. M. Steelman

Digital systems have been employed in industry as an aid in process evaluation and control for about 20 years. The earlier systems were quite simple and did little more than periodically scan a multitude of process variables, perhaps comparing them to alarm limits, and print out the results. As time passed, the needs of industry and the imagination of process engineers became more demanding. Rather than perform only alarm checking and logging, operating guides were generated to help the operator gain optimum performance from the process. Eventually, systems were entrusted with the job of manipulating the set points of the local analog control loops in a (DDAC) digitally directed analog control mode. Today digital systems are used to gather all-the process information, including both analog and digital variables; to make the necessary data manipulations; and to control the process end elements in a (DDC) direct digital control mode. During these years of transition from the very simplest systems to the complex systems of today, the demands upon the system engineer have been every increasing. The process engineer has required, among other things, more computational ability at high speeds, faster input and output rates, greater flexibility, better communication facilities (man-machine interface), (process oriented software), and finally, greater reliability at lower cost.

Jan 1, 1969

By Robin J. Hickson

The Ortiz Mine is operated by Gold Fields Mining Corporation, a subsidiary of Consolidated Gold Fields Ltd., one of the world's major gold producers. The Ortiz Mine is Gold Fields only heap leaching facility as well as being their first operating mine in the U.S.A. The hydrometallurgical processes utilized for recovery of gold and silver at Ortiz are discussed along with the several practical changes in operation adopted since start-up. Included are heap leaching by cyanidation, concentration of values on activated carbon, desorption, and the final electrowinning steps prior to shipment. Construction costs and pertinent technical data are shown.

Jan 1, 1981

"Mining used to be a business primarily focused on the technical aspects of getting valuable ore out of the ground and extracting the minerals efficiently. Without denying the importance of these skills, a narrow focus on technical issues is no longer enough to guarantee success when it comes to exploiting rare earth element (REE) deposits. Molycorp failed to enter the global REE market in a successful manner, while none of the many REE exploration projects has turned into an active mine so far and none is expected to commence operations in the near future. Accordingly, the world of REE is far more complex compared to other commodities. This paper looks into the REE industry to identify the factors that can connect potential U.S. REE mines to the market. The ability to break free from past thinking and become future-focused is a key driver. Mining of REE is pointless without a corresponding value-adding chain, while developing a value chain without first establishing an uninterruptible source of REE is also senseless. The mining sector must be based on the REE value chain and vice versa, along with the establishment of a market channel for the REE products that come out of the mine. INTRODUCTION It has been seven years since rare earth elements became the subjects of front-page headlines. It was when the controversial Chinese export policy for these critical commodities was epitomised in a maritime border dispute with Japan in September 2010 that resulted in the big REE crisis and price spike of 2011 (Barakos et al, 2016c; Mancheri, 2015). The world was dismayed, especially in REE-importing countries, such as the United States that was and is still totally dependent on Chinese production and exports (Barakos et al, 2016c; Kennedy, 2015). The short-lived alarm initiated a treasure hunt by way of exploration for REE deposits all over the world. The continuously growing demand on the one hand and the Chinese sovereignty of the REE-market on the other, led the rest of the world to explore their own REE resources. In just a few years, more than 400 projects were initiated to explore REE deposits outside of China (ERECON, 2015; Goodenough, 2016). The prices of REE, however, dropped rapidly and at the moment of writing this paper are in 6-year lows, at the level of the price average before the 2011 crisis (Barakos, 2017). The viability of even major established producers is being challenged, not to mention the development prospects of potential REE-market entrants (Barakos et al, 2016b; Rollat et al, 2016). Production cutbacks and industry consolidation in China impel REE market experts to forecast that prices have already reached their lowest point and have nowhere to go but up (Adamas, 2015; Roskill 2015). Yet, expectations for increased REE prices are limited and drastic changes are unlikely to happen in the near future, as there is still excess supply in the overall REE market (Barakos, 2017). Nevertheless, the low prices of rare earths are not the only reason that potential producers are struggling to enter the global REE market. Among other parameters, the separation of the individual elements seems to be the most important factor, as it is technically challenging and expensive to build and to operate."

Jan 1, 2018

By Joseph O. Cook

I know this is, at best, a frustrating period for the coal mining industry. About 20,000 miners have been laid off, mostly in the Appalachian and mid-western areas, and several mines are working less than 5 days a week; however, the industry is experiencing modern growth and, at least, there is the potential for future growth. The coal industry is probably only operating at about 80 percent of its present capacity, and it is certainly capable of helping this country solve its energy problems. Growth, as a rule, does not come easy, and growth in the coal industry is no exception to this rule. Many formidable challenges have to be overcome. As we all know, mining relies very heavily on the earth sciences, which have advanced significantly in the past few years, but we are always working in a changing environment which in most cases is a hostile environment. Large quantities of material are quickly extracted and rapidly moved in, generally speaking, a very confined area. The very nature of the mining business directly and constantly impacts our environment during this period in which the Nation and the world has become increasingly smaller and more concerned about protecting our environment. In addition, growth brings about an expanding work force which is increasingly younger and less experienced.

Jan 1, 1980

By H. O. Harju

In July 1968, P.T. Inco Indonesia was granted a Contract of Work to explore and develop the nickel laterite resources on the southeastern peninsula of the island of Sulawesi. Since 1970, exploration has centred on the deposits at Soroako as the site for initial project development. This paper describes the exploration methods used to evaluate these rather unique laterite deposits, the geology of which is described in the first section of this volume.

Jan 1, 1979

By L. Galarza

"INTRODUCTION Beneficiation of ores and minerals in a concentrator plant requires a significant amount of water [1] for the grinding and particle separation processes; most of it ends up being recirculated for reuse, slurry pumps are used after crushing and grinding feeding the ore to a classifier to separate fine-grained material (less than 5 mm) from coarse-grained material requiring further grinding. The lower ore grades [2] in the past couple of decades have demanded an increase on power size and efficiency of process machines to maintain a competitive plant throughput; Hydro-cyclone feed pumps to control both under and over milling or grinding are not the exception; Fig. 1 shows a conventional drive train [3] comprising an (1) asynchronous motor (also known as squirrel cage induction motor = SCIM), a high speed coupling (2), a gear reducer (3) and a low speed coupling (4) attached to the shaft of the pump (5), to accommodate the motor rated speed (typically 1800 rpm) to the process requirements (in the range of 250 rpm to 350 rpm), requiring additional components related to the gearbox: instrumentation, maintenance, disposable lubricants and filters, spare parts, thus reduces the overall system efficiency ultimately reflected into CAPEX and OPEX.WHY VARIABLE SPEED DRIVES FOR CYCLONE FEED PUMPS Hydrocyclones or commonly referred as “cyclones” are one of the most important devices in the minerals industry [4]; almost universally used in close-circuit grinding because of their high capacity and relative efficiency, the evolution of Power Electronics made affordable the use of Medium Voltage - Variable Frequency Converters (VFC) for Cyclone Feed pumps in combination with induction motors larger than 500hp (373kW) to gain multiple benefits: - Soft start with minimum electrical utility disturbance = inrush current mitigation - Full Torque available at zero speed for overload startup with pulp solidification after long still stand periods, superior to any other reduced voltage starting method. - Optimum and constant pump speed (independent of the electrical network or load condition), compared to across the line SCIM operation - Flexible Motor Voltage and Speed regardless of the power distribution Voltage and Frequency - Improved Power Factor (close to unitary), over the entire operating speed range"

Jan 1, 2015

By J. J. Renton

The iron disulphide minerals, pyrite and to a lesser extent marcasite, are ubiquitous to coal and coal associated rocks and are the source of nearly all the environmental problems associated with the mining, processing and utilization of coal. The iron disulphides as well as the other minerals in coal exhibit systematic spatial pat- terns of distribution on both regional and local scales and show predictable associations, most of which are determined by the geochemical-sedimentological controls under which they form. It is the purpose of this paper to discuss the geochemical-sedimentological conditions responsible for the formation of coal minerals with special emphasis on the formation of iron disulphides, to illustrate the regional and local patterns of mineral occurrence within coal, to present the microscopic associations of the iron disulphides and finally, to discuss the most important single environmental aspect of the iron disulphide content of coal and coal associated rocks; the production of acid mine drainage.

Jan 1, 1986

By D. R. Tesarik, T. C. Trancynger, W. G. Pariseau

The Davis detector cavern was excavated on the 4850 Level of the former Homestake Mine in the mid- 1960s to house a novel neutrino detector developed by Nobel Prize winner Dr. R. Davis. The original cavern was about 9.1 x 16.8 x 9.7 m high, excavated in a Precambrian amphibolite known as the Yates unit and enlarged in 2010. In 2009, the National Science Foundation selected the site for development as a national Deep Underground Science and Engineering Laboratory (DUSEL). This retrospective rock mechanics study of the Davis cavern is intended to inform design of the much larger caverns and laboratory rooms being considered for the same 4850 Level. Provision for rock mass variability, sequential excavation, jointing and wall damage from blasting are included in analyses that were done using two different computer codes and methods (FLAC3D and UTAH3). The results are in agreement with observations and show that cavern stability is indeed the case. The main conclusions are: (1) if conventional scaling of laboratory rock elastic moduli and strengths is done, then 0.25 and 0.50 scale factors are reasonable, (2) measured statistical and spatial variability in rock properties should be incorporated into geomechanical analyses to better reflect reality, (3) discontinuities (“joints”) are essential to reliable analysis of excavation safety and when properly taken into account eliminate the need for empirical “scaling” of laboratory rock properties, (4) major geologic features such as rhyolite dikes and breccia zones may be important to excavation safety at Homestake and should be explicitly represented in analyses and (5) quantifying wall blast damage is important to engineering design of underground excavations.

Jan 1, 2012

By Kevin Andrews, SETAREH GHAYCHI AFROUZ

Ground control analysis and groundwater inflow assessments for underground coal mines require in-depth field investigations including, but not limited to, geological and geotechnical core logging, downhole geophysical logging, laboratory rock strength testing, and packer (Lugeon) testing. Field and laboratory data collection are time consuming and expensive, and an initial understanding of the expected trends among various geotechnical and hydrogeological parameters can assist with the planning and optimization of geotechnical characterization studies and grouting plans. In this study, a comprehensive database is analyzed, comprised of important rock mass characteristics (hydraulic conductivity, rock quality designation (RQD), and lithology) for coal-bearing rocks in the Central Appalachian Basin. Statistical analysis of the data is completed to establish an enhanced understanding of geotechnical and hydrogeological conditions expected to be encountered as underground coal mining passes near and beneath streams and rivers. The results of the study provide valuable reference material for the coal mining industry for completion of shaft installations, mine stream crossings, environmental assessments, and grouting and mine dewatering designs.

Jul 1, 2023

By Iga Trisnawati, Fitria Puspita, Himawan Tri Bayu Murti Petrus, Gyan Prameswara, Idi Amin, Andi Nurfaadhilah Ulfah

Laterite ores, rich in essential metals like nickel, iron and cobalt, are a crucial resource for modern technology. However, the extraction of nickel from laterite ores is a complex process due to their intricate mineral compositions and low nickel concentrations. This paper presents the results of a study to understand the leaching behavior of preroasted laterite ore and the impact of roasting on leaching kinetics. The ore was subjected to roasting at 280 and 610 °C for a duration of three hours, followed by leaching in sulfuric acid (H2SO4) under atmospheric conditions. The results show that preroasting the ore at 610 °C significantly improved the recovery of nickel during leaching, with recovery rate of up to 93 percent, and the leaching process of the preroasted ore was primarily controlled by diffusion through the ash layer. The activation energy values were found to be 20.97 kJ/mol for the ore roasted at 280 °C, and 18.97 kJ/mol for the ore roasted at 610°C. These findings suggest that preroasting can enhance the leaching performance of laterite ore, potentially paving the way for more efficient and sustainable nickel extraction processes.

Aug 1, 2024

By J. L. Sloughfy

The size distribution and mechanical strength of the iron ore pellet burden are important parameters in determining the efficiency of the blast furnace. From the very outset, the guiding principle of our pellet quality improvement program was that these parameters are also the key to improving productivity and cost control at the pellet plant. Recognizing the need for improved blast furnace burdens and for higher productivity and lower costs at the pellet plant, Carol Lake operators, in conjunction with the IOC Pellet Quality Committee, established the following goals for the improvement of Carol pellets: [ ]

Jan 1, 1981

By Anastasia Xenaki, Edmundo Laporte, Antonio Nieto, Jesus Castillo Gomez, Oscar Velasquez

It is particularly challenging for the mining industry to create and implement an efficient and adaptable mining innovation model to secure the continuous improvement of processes and products via technology. Human resource departments must play a vital role in shifting the mining culture, enabling these new classes of digitally skilled professionals to manage the mining operations of the future. This paper proposes the implementation of a concept based on the 5S mining innovation model ((a) Nieto, 2019), in a coal mining project in Central Asia, Mongolia. Practical and empirical evidence suggests that the model could serve as a roadmap to developing technologies and methods for the mines of the future.

Feb 1, 2023

By G. W. Luxbacher

Coal mine infrastructure is rarely designed solely on the basis of ventilating the underground workings. Instead the optimization of a mining sequence, the minimization of coal quality variation, reduction of coal losses by adapting to property boundaries and geologic structure (seam inclination, roof conditions, coal thickness, etc.) or other similar considerations have formed the objective for mine plant design and layout. Infrastructure development may also reflect a desire to maximize production early in the life of the mine or to permit flexibility in mining according to market conditions. Requirements for coal mine ventilation, established by the 1969 Coal Mine Health and Safety Act, have mandated changes in the traditional concepts of mine plant design in the United States. Mines, in operation prior to the passage of the Act have experienced severe limitations when attempting to adapt the existing mine infrastructure to meet the requirements of the law. In addition the increased quantities of air required, velocity limitations on trolley haulage and belt lines, the establishment of separate intake escapeways and gob area ventilation have com- pounded the inherent complexity in planning mine ventilation systems. Past practices in mine ventilation planning and design are no longer adequate. Given the complexity of today's ventilation systems, effective planning and design approaches are required. As such, the interrelationship between the overall coal mine plant design and ventilation system design is examined. An approach to ventilation system design constrained by global considerations of mine plant design, is presented. The proposed approach is, however, applicable to the design of new mine ventilation systems as well as to the modification of existing systems.

Jan 1, 1980