Search Documents

By S. P. Singh

In order to simulate the operation of coal extraction machines, a portable workability instrument has been designed. Initially, the tests were performed with the instrument on modeling material, which were followed by in situ tests on coal in underground mines. The peak and mean cutting resistance and work done to cut a unit length of coal were determined for coal as well as modeling material. In addition, rebound strength and dynamic penetration tests were also performed in situ. On the basis of the cutting characteristics of coal, a "Workability Index" has been developed and its role in the judicious selection of coal cutting machines has been discussed. With reference to prior works and the strength characteristics of coal, it was found that the coal plow may not be suitable for the seams under investigation and the shearer seems to be the only choice. It has been observed that peak cutting resistance and the "Workability Index" in the case of coal as well as modeling material depend upon compressive strength. The peak cutting resistance exhibited certain dependence upon the Schmidt rebound hardness and dynamic penetration strength of coal in situ.

Jan 1, 1984

By D. C. Ridenour

The pressure system of ventilation with large diameter bore holes has been very effective in the ventilation of two gaseous mines, the Olga No. 1 and No. 2 Mines in McDowell County, West Virginia. The No. 4 Pocahontas Coal Seam on the Olga property lies 580 feet below the valleys. The seam is very gaseous as well as dry and dusty, which makes good ventilation all the more essential. Irregular and often extensive areas of the coal seam have been replaced with impervious shales and sandstones in "Fault" or "Want" areas. The replacement materials have sealed the methane in the coal seam and thus increased the quantity of gas that must be handled as mining is done. Often the No. 5 Pocahontas Seam comes down to meet the No. 4 Seam at the Faults and considerable methane is sometimes released from the upper seam. The factors mentioned, together with the irregular and unpredictable lateral shape' of the faults, result in long narrow stringers of coal that are very gaseous and difficult to mine. So far as the Olga Coal Company is concerned, the most effective ventilation under the conditions outlined has been the use of large diameter bore holes with a pressure ventilation system. The ventilation of a mine can be accomplished in two fundamental ways. The mine atmosphere maybe reduced below atmospheric pressure by an exhaust fan; or it may be raised above atmospheric pressure by a pressure fan. In either case, the coursing of the air is so planned as to have the haulage and traveling ways on intake air. While the majority of the coal mines in the United States, no doubt, use the exhaust system of ventilation, there are several advantages of the pressure system which are extremely beneficial.

Jan 1, 1960

By L. F. Moran

Rod Mill Grinding is an important and fundamental step of the concentrating process in Marcona Mining Company's plants at San Nicolas Bay, Peru. This Paper summarizes experience in regard to consumption and specifications of grinding rods based on twelve years operation of the grinding circuits. Marcona operates a Plant complex producing 10 million tons per year of beneficiated iron ore products including pellets, sinter feed concentrates, high grade concentrates as slurry and filter cake. Processing capacity is 15 million tons per crude ore per year of which 13 million are around in rod mills. A continuous testing program was carried out over the years. Initial studies of daily production operations gave indications of poor grinding rates in relation to mill size and power consumption, with a high rate of broken liners and rods. The broken nieces of rod were not automatically expelled and further interfered with grinding efficiency, while replacement of liners caused unwarranted do n tire. Objectives were to improve all phases of the Process by studying the effects of changes in rod diameter, length, alloy constituents, and volume and weight of rod charge.

Jan 1, 1975

By J. J. Harrington

Manufacture and mixing of flotation reagents at the mill site provides an economic and convenient method of maintaining a continuous and fresh supply of reagents for concentrator operations. Kennecott Copper Corporation has designed and built a Reagent Mixing Facility which incorporates new ideas in construction and fail-safe operation at its Nevada Mines Division concentrator. Highly sophisticated automation and instrumentation techniques are combined with safety procedures and equipment that meet and exceed all Federal and State safety requirements. Installation of the facility has minimized hazardous working conditions for the operator, isolated reagent preparation from production personnel and equipment, and reduced the time required for reagent preparation from three shifts to one shift per day.

Jan 1, 1976

By S. A. Montague

In spite of the many new insulating materials, both synthetic and manufactured, that have been put on the market since the end of World War II, and notwithstanding the many millions of dollars applied to the development of synthetic mica, natural block mica1 is still a most indispensable insulator in various electronic components. It will remain so, barring some spectacular break-through in research that might provide a substitute fully acceptable as a replacement for mica in all of its superior properties. But this is not to say the future for mica is assured, or free from serious problems. Technological advances have created problems requiring a solution to be found if future requirements are to be filled.

Jan 1, 1962

By Dennis F. Koschak

Production tests at Reserve Mining Company's iron ore pelletizing plant established that rubber-lined balling dm produce a green pellet equivalent in quality to those produced in conventional balling drums equipped with reciprocating cutter bars. The flexing action of the rubber liner prevents concentrate buildup in the drums, eliminating the need for a cutter bar. Advantages of the rubber-lined drum includes a reduction in maintenance and operating manpower, reduced bentonite consumption with less drum surging, reduced power consumption, and improved drum on time.

Jan 1, 1983

By R. E. Coleman

Infrared spectroscopy, employing the internal reflection method in conjunction with solvent extraction techniques, was used to study surface reactions between aqueous potassium ethyl xanthate and both sphalerite and precipitated zinc sulfide each activated with aqueous copper sulfate. It was determined that reactions occurring on the sphalerite and zinc sulfide surfaces produce the reaction products ethyl dixanthogen and cuprous ethyl xanthate, some of which are ad¬sorbed on the mineral surfaces. According to infrared spectra showing the reaction to form these compounds, the ratio of cuprous ethyl xanthate to ethyl dixanthogen adsorbed is directly related to pH of the flotation solution.

Jan 1, 1967

By M. Sengupta

Surface mining in arctic regions is characterized by many unique problems. Continuous and discontinuous permafrost (perennially frozen ground) occurs in most of the arctic and subarctic areas. Permafrost presents special problems of slope stability. Stability of permafrost depends on its temperature, moisture content and material type. Permafrost slope fails due to solifluction, disturbance of ice rich slopes, and liquefaction. Drilling and blasting of frozen ground present special problems. Depending on their degree of saturation with water, freezing soils and rocks have a number of important characteristics that affect blasting efficiency. Metals used in mining equipment and mining structures require special selection. At low temperatures many steels lose most of their normal ductility and toughness (resistance to brittle fracture). The paper discusses engineering solutions to unique problems of arctic mining.

Jan 1, 1986

By Henry J. Schwellenbach

The New York Trap Rock Corporation has four plants located along the Hudson River, all within 70 miles of New York City. The company produces crushed stone for use as construction aggregate, with a total annual production amounting to 6 million tons. The crushed stone is moved to markets in metropolitan New York, New Jersey and Long island areas by water transportation. There are daily deliveries of approximately 35 scowloads to the market area. Its customers are contractors with ready-mixed concrete and asphalt plants located on the water, where the aggregate is unloaded for its ultimate use. For a number of years capital equipment was replaced only when the current operating machinery was no longer serviceable, or when' a need was apparent for a different type of equipment. There was no particular regard for efficiency or for operating and maintenance costs. Such lack of system often resulted in the emergency purchase of equipment which was later found to be unsuitable for the job. A few years ago it became apparent that a systematic procedure was necessary. After evaluation of several systems, an individualized plan was evolved from the basic pattern developed by the Machinery and Allied Products Institute. The system adopted by New York Trap Rock has proved wholly satisfactory.

Jan 1, 1959

By K. A. Brunk

This paper describes Newmont's research, operations, history and experience with pre-treatment of preg robbing carbonaceous ores. The chemistry, physics and kinetics of chlorine treatment are described. Present operations, control strategy and projected changes are discussed. Included is a summary of the adsorption of chlorine into pulps and off-gas scrubbing.

Jan 1, 1987

By G. Kris Kapoor

Each new period of public concern, whether rooted in things political, social, economical, or technological, brings with it new words or phrases which highlight that new interest. With people's awareness of our rapid depletion of readily available energy sources and the enormous increase in energy .costs came the new, and now often heard, terms "energy intensive", "energy sensitive", and "energy conservation". Since its birth in 1926, Fuller Company had been directly associated and involved with energy intensive products and processes. We are located in the heart of the Cement Industry. Many of our products and processes are geared to the needs of the portland cement manufacturer, and a look at the inferno within an operating cement or lime kiln will certainly convince anyone that here is an energy intensive process. Fuller Company, then, has always been energy sensitive. Process kilns, hard rock crushers, tube and roller mills, fluid bed thermal reactors, pneumatic compressors and conveyors, material coolers - all are Fuller Company products utilizing or transferring large amounts of energy. Consequently, much of our success in the marketplace depends on how wisely we design and plan for efficient use of power and for conservation of each unit of heat available.

Jan 1, 1975

By Steven W. Hunt, Gregory C. Baker, Glen J. Rorison

Microtunneling methods were utilized beneath pile-supported clarifier basins to replace settlement damaged sludge drain lines at the Jones Island Wastewater Treatment Plant in Milwaukee, Wisconsin. To minimize the risk of blockage and expensive recovery of a microtunnel boring machine against pipe piles or construction debris, a Soltau RVS 80 was utilized. This machine allowed the alignment to be initially bored with guided 114-mm diameter rods to ensure proper alignment and lack of obstructions. Casing pipe was then installed by jacking 1-m long, 305-mm diameterclay pipe along the rods and behind an auger head. This case history also discusses how 2.4-m diameter precast concrete pipe was used as a one-pass sinking caisson for workshafts and new cleanout manholes.

Jan 1, 2001

By J. R. J. Edwards

Jaspilite, a mineral consisting of silica and iron oxide in varying proportions, is one of the host rocks of the high grade ore deposits situated in the Middleback Range of South Australia. As a result of laboratory investigations, a flowsheet was postulated for the beneficiation of jaspilite to produce an acceptable grade product for feeding to blast furnaces, The flowsheet involved the reduction of the hematite in the haspilite to magnetite, the grinding of the reduced product to 95 pct minus 325 mesh Tyler followed by wet magnetic separation, hydroseparation and filtration to yield a magnetite concentrate. Agglomeration of the fine concentrate would then be necessary to meet the physical requirements of blast furnace feed. To prove the postulated flowsheet, to obtain a more accurate estimate of costs and to obtain design data for a commercial installation, a pilot plant was constructed at Whyalla, South Australia.

Jan 1, 1960

By William G. Schultz

Sylvite of Canada, a wholly owned subsidiary of Hudson Bay Mining and Smelting Co., operates an 8000 TPD potash mine and refinery located nine miles North East of Rocanville, Saskatchewan. Prior to Hudson Bay's entry in 1968 into potash mining and refining, it was one of the more traditional and conservative Canadian Mining Companies whose principal business had been for many years a successful copper-zinc mining and smelting operation located at Flin Flon, Manitoba. The potash reserves being mined by Sylvite were acquired through the acquisition of Francana Oil and Gas. This acquisition was at the time when several major potash mines were being developed or had recently been brought into production in the Province. These mines are owned by either very substantial Canadian Mining Companies or Multi-National Mining Companies with considerable potash mining experience. At that time, it became very apparent because of the new mines coming into production, potash mining and refining would quickly become a very competitive industry. Because of long term considerations, Hudson Bay decided to proceed with the development of its potash reserves, recognizing the Mine and Refinery would have to be the most advanced available in order to successfully operate. This report deals with the mining operation at Sylvite and the degree of success Sylvite has achieved.

Jan 1, 1972

By Jon G. Baird

The suggestion of the use of measurements of trace amounts of mercury as a guide to the location of sulphide ore deposits was first made by the Russian, A. A. Saukov (1), in 1.946. Since Saukov's original work, many others have studied the abundance of mercury in nature, the association of mercury with sulphide ores and methods by which very minute quantities of mercury can be measured in air, soil, rocks, water and plants. The most abundant of the mercury bearing minerals is cinnabar (HgS). Native mercury is also found and sulpha-salts like tetrahedrite are known to have important mercury contents. Other sulphides of base metal deposits contain mercury in amounts ranging from parts per million to as much as one or two percent. (2) The mercury content of sulphide-free rocks is usually less than a few hundred parts per billion (1 ppb - 10-9), Soils usually contain less than 100 ppb and water less than 1 ppb of mercury. Normal atmospheric air contains about 1 nanogram (10-9 grams) of Hg per cubic metre although higher concentrations can be observed near mercury occurrences, sulphide deposits and volcanic exhalations.

Jan 1, 1973

By George W. Parker

The ever increasing costs of labor and supplies have made it imperative that operators of open pits look for some way in which to cope with these increases. One of the most logical ways to increase the efficiency of an operation is by the introduction of larger haulage equipment, as generally haulage costs are the greater portion of the over all expenses. These larger haulage units require larger shovel units. In the late 1930's and the early 1940's large mining, quarrying and heavy construction operations had more or less standardized on the 4 to 6 cubic yard shovels. During this same period the haulage units were generally 22 to 27 tons. Some ten years ago 9 - 13 cubic yard shovels along with plus 50 ton haulage units were introduced by manufacturers in an effort to enable operators to decrease costs.

Jan 1, 1962

By Daniel T. Hegyan

The employment of continuous rotary vacuum disc filters to filter refuse from the fine coal washing circuits has been increasing as it has become more important to close the water circuits and eliminate sludge holding ponds. This paper will discuss our past experience filtering refuse, effects of solids concentration in the filter feed, use of polymer flocculation aids, effect of flocculation devices, and effects of particle size and ash content on the filtration rate. Detailed tests were performed on existing installations utilizing coal refuse filters to determine optimum flocculant dosage, solids concentration, and disc rotation speed to form a dischargeable cake. Information was also obtained showing effect of flocculant addition on the moisture of the filter cake. Our test work has shown that the continuous filtration dry cake rates for fine coal refuse correlates very well with the data developed and presented by Silverblatt and Dahlstrom1 except that the curves have moved up the scale by use of polymer flocculant additions. These polymers were not available at that writing. Finally, our tests also confirmed the general premise stated by S. K. Mishra2 that controlled additions of polymer flocculants will reduce filter refuse cake moistures somewhat.

Jan 1, 1974

By Donald G. Rogich

The concept of initiating a large action-oriented contract, directed toward inherently safe mining systems, was conceived by the U. S. Bureau of Mines in January 1970. At that time we were in the process of establishing research contracts and grants, about 100 of which were let in FY 71 to deal individually with fairly specific technological areas. These projects in the aggregate covered a wide spectrum of health and safety problems. What appeared to be necessary was the creation of a project or program that would provide a focal point for the demonstration of many of the results of this research and also in the action sense culminate with working hardware and systems that could be tested and demonstrated over a fairly long teen. The concept of working demonstrable systems, rather than just a conceptual study, was, felt to be necessary for two significant reasons. In the development of any new system, the translation from concept to working hardware is usually a costly and time consuming process which acts as a deterrent to implementation. Secondly, many decisions in the mining community to change equipment or systems ,are based on first hand observation of the new system, in operational practice, an attitude which is certainly understandable in view of the high capital costs of equipment. The decision was made to procure a single R&D contract which would be aimed at developing underground coal mining systems which

Jan 1, 1972

By C. W. Overton

The operations of Bethlehem Copper are situated in the south-central interior of British Colombia at an elevation of 4900 feet above sea level. Main road and rail transportation systems pass through Ashcroft in the Thompson Valley, which is 28 miles by road from the minesite. The operation was the first low-grade open-pit porphyry copper mine in British Colombia. The minerals are chiefly chalcopyrite and bornite, while the rock is principally feldspar and quartz. In the outer fringes of the orebodies sane pyrite is present. Average grade of mill feed is 0.55% copper.

Jan 1, 1973

By James D. Cooper

Long range projections of demand for nonmetallic minerals are presented, together with data on the domestic resources which are available or which can be made available to meet the requirements through the balance of the century. Past successes in solving nonmetallic mineral requirement problems are briefly reviewed to illustrate the capability for solving present and future problems of a similar nature. Major problems threatening the future supply of specific industrial minerals are described together with possible methods for assuring the necessary raw materials for future needs. The growing importance of environ- mental degradation, land use conflicts, and other important factors which affect several or all of the nonmetallic mineral industries is covered, and the necessity of planning for efficient and orderly extraction and rehabilitation of mineral deposits is stressed. The present Bureau of Mines methods and tools for long range planning are briefly discussed.

Jan 1, 1969