Search Documents

By C. C. Huang

Rare earth compounds, such as samarium-cobalt compounds and neodymium-icon compounds, are being used more often for the manufacture of permanent magnets, because these materials permit the production of permanent magnets with higher magnetic energy potential than the conventional ferrite magnets. Especially, the recent rapid developments in the field of electronics and electro-technology have demanded an increased production of rare earth magnets. Unlike ferrite, which is typically produced by a wet process, rare earths can be ground and classified either in a wet or dry process. In the past, batch ball mills, through-pass ball mills in circuit with air classifiers, and conventional jet mills were primarily employed for the dry processing. These methods, however, have suffered from the problems, for example, wear and contamination, low product quality In particle size distribution, difficult to adopt inert-gas operation, and high specific energy consumption. In this report, dry processing of rare earth powders will be presented, especially ultrafine grinding with fluidized bed jet mill.

Jan 1, 1993

By S. E. Phillipson

Slickensides cause potentially hazardous ground conditions in underground coal mines. Investigations by MSHA’s Roof Control Division indicate that many slickensides represent bedding plane faults and drag folds that formed during coal bed decollement, a style of faulting that occurs in shale units above coal seams. These slickensides formed in response to regional tectonic compressional stresses, rather than by differential compaction, and are parallel to folds and thrust faults. This paper relates slickensides in the Appalachian, Illinois, and Black Warrior basins to the structural grain of the Appalachian Mountains, provides descriptions of slickensides, and advocates geologic mapping as a predictive method for identifying areas with adverse ground conditions.

Jan 1, 2003

By C. W. Matthews

Introduction Screening is defined as a mechanical process which separates particles on the basis of their size and their acceptance or rejection by a screening surface. The key element in this method of particle sizing is obviously the screening surface, the medium that contains the apertures for the passage of the undersize material. This surface must be strong enough to support the weight of the material being screened, flexible enough to yield to the vibrating force applied to it, yet light enough to provide a reasonable ratio of open area to attain a practical through- put. To balance all of these factors is difficult enough. The problem is compounded, however, because screening media are made in a great variety of types, shapes, sizes, and materials of

Jan 1, 1985

By Frank C. Stevens

The availability, cost and use of fuel and electricity for the cement industry is difficult to predict with a great degree of accuracy because the historical pattern of factors affecting energy was disrupted during the years 1972, 1973 and 1974. Forecasting is both an art and science and is based on .the premise that the best indicator of the future is the past. Statistical data is used to guide economists and businessmen in their predictions of the future. Even though the energy picture is changing, it is believed that electricity and fuel will be available for the cement industry in the foreseeable future, and this energy will be more costly in relation to the other items that are part of the manufacturing costs for portland cement.

Jan 1, 1977

By B. R. Arvidson

Sharper separation and improved control of the top size increases the fine particle product yield. As the milling circuit recycle stream is reduced, the overall capacity is increased. In some cases, a doubling of throughput is realized, although 25 to 30% increase is more typical. Alternatively, the energy demand may be reduced, although the best economic improvement results from higher capacity. A comparison with a high-pressure roller mill circuit shows that an optimized ball mill circuit retrofitted with the new air classifier has lower energy consumption. The new air classifier features low energy demand and substantially lower maintenance compared to similar equipment. Design and operation of this recently patented classifier are discussed. Several industrial installations will be described.

Jan 1, 1999

By D. W. Park

A vast majority of longwall operations in the United States use shield-type hydraulic supports to provide ground control along the longwall face. The three-dimensional finite-element technique combined with a progressive failure approach was utilized to simulate interaction between shields and surrounding strata and determine various loading conditions. In addition, a separate finite element model of the shield structure was made to study responses of each long wall shield to the different loading conditions. Shield responses under various loading conditions and the shield characteristics, such as shield stiffness, the ability of resisting horizontal forces, and the effect of shield height, were studied based on the results from finite-element analyses. The results can provide the basis of effective shield design and be used for evaluation of the shield performance. It is suggested to develop a technique incorporating the finite-element method to evaluate the real-time shield performance for the purpose of effective ground control.

Jan 1, 1992

By S. A. Moffatt, S. K. Kawatra, T. C. Eisele

This paper describes the decomposition of bulk samples to fine particles using alkali metal vapors. Basalt, pyrite, alumina, pyrex and quartz glass samples were exposed to sodium vapors at elevated temperatures for different time periods up to 30 hours. Examination of the particles showed that fragmentation occurred preferentially along grain boundaries. Emphasis of this paper is on the theory of the degradation mechanism and the size distribution of the particles produced.

Jan 1, 1992

By B. Andersen

An accurate knowledge of Interactions among mineral particles and between such particles and dissolved and precipitated species Is Important in developing efficient separation processes. In this investigation interactions in Florida phosphatic clay waste, that are relevant to dispersion and selective reagent adsorption, the two main prerequisites for selective flocculation, were studied. Initial studies with artificial slimes, consisting of pure clay and phosphate minerals, showed dispersion of artificial slimes to be relatively easy. The problems that were encountered during selective flocculation of the artificial slime were due to unselective polyacryllc acid adsorption on clay, which was caused by the presence of multivalent calcium ions on the exchangeable cation positions on the clay surfaces. This problem could be solved by exchanging calcium for sodium, which reduces the interaction between the polymer and the clay surface. This procedure, however, was not successful for mineral mixtures. Natural slimes were found to be much more difficult to disperse. This was attributed to the presence of cementing materials such as humic substances and Ai and Fe (hydr)oxide precipitates. Selective removal of these cementing materials resulted in good dispersion and partial separation. Further increase in separation of natural slime is likely determined by the presence of calcium on the clay surfaces, as was found for the artificial mixtures.

Jan 1, 1992

By E. F. Schnitzer

During 1996 and 1997, Oregon experienced flooding on a scale not seen in many years. Some gravel pits located near rivers experienced erosion and, in several cases, breaches between the gravel pit and the river. Initial evaluation of several sites that experienced breaches indicates that impacts to the river system are complex and vary significantly from site to site. The impacts to the adjacent river system may be viewed as both positive and negative. Several floodplain-mining sites in Oregon located in areas of historic river flow have reverted to active riverbed. In many cases, state and federal fisheries biologists and university researchers see the resulting increase in channel complexity and habitat as favorable. The Oregon Department of Geology and Mineral Industries -Mined Land Reclamation Program (DOGAMI-MLR) is performing additional studies of the impacts to the off-channel areas that resulted from the 1996 floods. More data is needed to make sound floodplain decisions regarding mining.

Jan 1, 1999

By Kevin B. Doyle

Virtually all industries use sulphur in some form. About half of the world's production is used in the production of fertilizers. Sulphur is produced in one form or another in over sixty countries in the world. The major producing countries, in order of importance, are: U.S.A., Canada, U.S.S.R., Poland, Japan, France, Mexico, and Spain. Canada is the largest exporter of sulphur presently supplying about 30% of the world elemental sulphur export trade. It has held this position since 1968. World sulphur resources are virtually unlimited. Future world competition will come from Iraq and other Middle East countries as well as Central and South America.

Jan 1, 1978

Power plants that utilize conventional wet flue-gas desulfurization methods produce enormous amounts of flue-gas scrubber sludge. A typical 400 MW power station that burns a high sulfur coal produces 170,000 tons of wet flue-gas scrubber sludge per year. This scrubber sludge is currently landfilled at an enormous cost to utility companies. This material could be used as a raw material for industries that use gypsum, such as the wallboard and plaster industries. However, before it can be used as feedstock for these industries, some of the impurities such as unreacted limestone and silicates must be removed from the scrubber sludge. Froth flotation has tremendous potential for separating these impurities from scrubber sludge. In order to select an optimum flotation process, it is necessary to characterize the surface properties of the major components in the scrubber sludge, which consist of calcium sulfite, calcium sulfate, calcium carbonate (limestone), and silica. In this study zeta potential measurements were used to determine the surface charge of the components in scrubber sludge, with the goal of optimizing a froth flotation process to produce a marketable gypsum product for the wallboard and plaster industries.

Jan 1, 1996

By Donald D. Born

Mine No. 95 is located in Harrison County about 5 miles west of Shinnston, WV, with coal properties covering the northwest corner of Harrison County and the southwest corner of Marion County and with adequate Pittsburgh seam reserves to support the mine for many years. The mine was opened in 1967 and was planned, projected and operated as a room and pillar mine. It is located on a spur branch of the Baltimore and Ohio Railroad, has rail loading facilities and shipped by rail during its development stage. In 1972 it was converted to a mine mouth power station supplier and now transports coal by conveyor belt directly to the Harrison Power Station of Allegheny Power System. In 1971 the first longwall unit was installed in a selected area of the mine and immediately an orderly system of planning was developed to overcome the restrictions associated with longwall mining. The first was the development of the technique necessary for the plugging of abandoned oil and gas wells that existed in the area. With the assistance of the Morgan- town Energy Research Center of the Bureau of Mines, this restriction was overcome and thus opened a great potential for longwall mining in northern West Virginia. Other restrictions that had to be considered for longwall planning were dwellings and other improvements, snap top zones, water courses, and adequate bleeder systems, and the handling and treatment of mine drainage. In 1975 the second longwall unit was installed and soon therefore became a total longwall mine.

Jan 1, 1986

By Cahit Helvaci, Robert B. Kistler

Borates are defined as ' 'salts or esters of boric acid; a compound containing the radical B203" (Bates and Jackson, 1987). Borates are defined by industry as any compound that contains or supplies boric oxide. A large number of minerals contain boric oxide, but the three that are the most important from a worldwide commercial standpoint are: borax, ulexite, and colemanite. These are produced in a limited number of countries (Fig. 1), dominated by the United States and Turkey, which together furnish about 90% of the world's borate supplies (Lyday, 1991). Production in the United States originates in the Mojave Desert of California; borax and kernite are mined by US Borax from its large deposit at Boron. Borate containing brines are pumped from Searles Lake by North American Chemical Co., and a limited amount of colemanite is mined by Newport Mineral Ventures from Death Valley. Turkish production is controlled by Etibank, the national mining enterprise, which supplies most of the commercially traded ulexite and colemanite from mines in the Bigadic and Emet Districts, plus borax from the huge deposit at Kirka. Borate minerals have been employed in a wide range of uses for many centuries, dating from at least the 8th century when they were used primarily as a flux for assaying and refining gold and silver. Their valuable properties and relative rarity soon stimulated international trade in borates; Marco Polo claimed to have trans- ported Chinese borate minerals from Tibet to Europe, and his home port of Venice was the center for borate imports and use throughout the Middle Ages (Travis and Cocks, 1984). Borates were traded at relatively high prices for highly specialized applications into the late years of the 19th century. At that time they were being used for medicines, food preservatives, ceramic glazes, and in expanded applications as metal fluxes. It was in that era that borax was discovered in Clear Lake, CA, and more significantly, the playa deposits of western Nevada were found and exploited by F.M. "Borax" Smith and others. Research and development by Smith's company began the evolution of borates from a high priced commodity with a few specialized uses to the relatively low priced chemical raw material used in large tonnages on a worldwide scale today. Borates are often defined and sold by their boric oxide or B,03 content, and most statistical data are listed in tons of B203. Of the products sold by the industry, borax pentahydrate or 5 mol and boric acid are the most commonly traded commodities. Boric acid plants are operated by all of the major borate producers. Glass fiber insulation is the major end use in the United States followed by textile glass fiber and borosilicate glass, detergents, and ceramics. Detergent usage continues to be a major end use in Europe.

Jan 1, 1994

By Y. Ye

Typically, rougher molybdenite flotation and recovery from bulk copper/ molybdenum concentrates involves the use of alkalisulfides, Nokes reagents, cyanides, oxidants, and/or thermal treatment for the depression of copper sulfide minerals. The bulk copper/molybdenum feed generally varies from 0.2% Mo to 1.0% Mo, and with traditional reagents the single-stage rougher flotation recovery of molybdenite varies between 40 and 90% at a concentrate grade of 5 to 10% Mo. With ozone conditioning for copper depression, however, improved separations appear to be possible, as demonstrated by tests with Cu/Me concentrates from both the Phelps Dodge Morenci Operations and the Kennecott Copperton Operations. Single-stage rougher flotation after ozone conditioning can provide a molybdenum concentrate at a recovery of more than 90% and a rougher concentrate grade higher than 20% Mo in some cases. Subsequent cleaner flotation with additional ozone conditioning results in relatively copper-free molybdenum concentrates containing as much as 52% Mo. Preliminary analysis indicates that, with a multistage ozone conditioning/flotation strategy, the process is technically and economically viable and should be suitable for industrial application.

Jan 1, 1990

By Carl R. Peterson

The Rapidex continuous drill and blast tunneling concept utilizes a unique spiral blasting pattern that permits efficient performance with relatively small single shots, while at the same time directing major blast fragments at right angles to the tunnel axis. The concept's self-shielding geometry permits the design of a lightly shielded machine that can stay at the tunnel face firing frequent small blasts to provide rapid, virtually continuous advance. This paper describes Phase III of the development program (supported under Bureau of Mines contract H0252047) in which the "front end" of the machine?drilling loading, and shooting components, together with the shield--was fabricated and field tested underground at the White Pine Copper mine, Michigan. One of the major accomplishments of the Phase III effort was to develop a fully remote controlled loading and initiation system in which explosive slurry is pushed, through a hose into the blasthole by a small water-driven piston carrying the blasting cap. The cap is ignited via an induction coil just prior to entry into the borehole, after which a delay permits complete -withdrawal and shielding of the loading hose. The ultimate objective of the present Bureau-sponsored program is to evaluate the feasibility of mechanizing hard rock mining operations, such as development to a point where drilling, loading, shooting, and mucking can proceed simultaneously and result in increased productivity.

Jan 1, 1977

A case study of a systematic approach to grinding circuit steady-state optimization is presented. After overall review of the flowsheet, two circuits were prepared for detailed testing. Functional performance analysis was chosen as the primary modelling system, and on this basis a quality assurance program for data gathering was implemented. A number of circuit design and operating variables were experimented with statistical analysis of plant test results revealed relationships previously unquantifiable by any other modelling technique. Improvements in classification system and mill grinding efficiencies were demonstrated and significant energy cost savings thus realized.

Jan 1, 1998

By S. M. Smouse

Total world energy consumption is projected to continue its strong growth of recent years. Because coal is the most abundant fossil fuel, it will likely remain an important energy source, particularly for power generation, into at least the early years of the next millennium. Clean coal technologies are available today that can economically reduce air pollution, primarily SO2 NOx and particulates, and for the higher efficiency technologies, CO2, from power generation. U.S. Department of Energy analyses show that the adoption of clean coal technologies could decrease carbon emissions worldwide while creating a strong export market with attendant creation of jobs in the U.S.

Jan 1, 1998

By J. Herbst, I. Heber-Panu, Dan G. Cojocariu, E. Ene-Danalache, G. Poling

A general model which represents not only batch but also continuous flotation in multi-cell machines is presented. This model considers both the size distribution and the distribution of flotabilities in a size class for valuable mineral particles in the pulp. The general expression is shown to reduce to several previously reported models. In addition, a number of new models are found to arise for different specific assumptions concerning the flotability distribution and/or the size distribution of the particles undergoing flotation. Several of these new models are tested experimentally using laboratory-scale batch and pilot-scale continuous data. Model parameters are estimated from this data and a comparison of calculated recoveries and those experimentally determined are presented. Finally, the influence of the feed rate, aeration rate and valuable mineral content of the feed on the recovery is examined.

Jan 1, 1976

By M. Misra

It is estimated that the volume of low -level and intermediate level contaminants present in the soil at different DOE sites is of the order of several million cubic feet. The existing remediation scheme is containerization followed by burial in Land Disposal Facilities (LDF's) which is economically unattractive warranting the need to develop alternate remediation routes. One such route is the physical separation based volume reduction approach to removing a MINIMUM AMOUNT OF CLEAN SOIL with the radioactive particles, reducing the amount of material that requires disposal. The purpose of this study was to evaluate and test the feasibility of using physical beneficiation techniques for removal of contaminants from soil. The performance criterion was to recover at least 80% of the activity in 20% or less of the original contaminated soil volume. Four different radioactively contaminated (primarily uranium and plutonium) soils from DoE sites namely LANL, INEL, Fernald Plant 1 Storage Pad (ID-B) and Mound soils were tested using gravity, magnetic, gravo-magnetic, hydrocyclonic and flotation devices. The paper is divided into the two sections. The first section presents the overview of the Heavy Metals in Contaminated Soil Treatability Project conducted at the University of Nevada, Reno (UNR) describing the salient features of a state-of-the art Soil Washing Laboratory and the technology equipments used in the test program. The second section describes the soil characterization and typical volume reduction results obtained from the UNR tests. Among the physical separation processes, only flotation processes passed the performance criterion. For the LANL and INEL soils where the contamination was contained in coarse particle size, it was possible to recover more than 80% of the activity in less than 10-20% of the original volume of the soil thus rendering 80-90% of the soil "clean". For Fernald and Mound soils where contamination was of colloidal nature, flotation based processes showed encouraging results and are recommended for further studies.

Jan 1, 1995

By D. A. King

Monitoring devices have been installed at several mine sites to assess the potential for the development of acid rock drainage (ARD) in waste rock, spent ore, and tailings material. In addition, instrumentation has been designed for monitoring changes in water quality in pit lakes. These devices monitor temperature, oxygen, water movement, and water chemistry in the waste rock pile. This information can be used to evaluate the current and future ARD risk, the effectiveness of caps and covers, and provide information to aid in the design of other reclamation strategies that limit ARD development. The instrumentation includes nested thermistors and oxygen sensing ports, neutron access tubes, heat dissipation units (HDUs), and lysimeters. Many of the monitoring devices can be linked to a datalogger and telemetry systems, enabling monitoring data to be downloaded from the office.

Jan 1, 1997