Search Documents

By Michael J. Friedel

The scale-dependent hydraulic properties in a fractured porphyry copper oxide deposit are investigated for relevance to in situ leach mine (ISLM) design. In most well field designs, mine operators assume that hydraulic properties represent a continuous spatial function, or continuum. The problem, however, is that the representative elemental volume, the volume over which hydraulic properties are described as a continuum, is a domain (if it exists) that occurs between end members representing varying degrees of heterogeneity. At the Cyprus Cas a Grande mine, transmissivity fluctuations are spatially correlated suggesting that at the scale of ISLM, the hydraulic process is heterogeneous and a typical continuum representation is inappropriate for design. Alternatively, a conditional stochastic approach using the simulated annealing (SA) technique is deemed useful for the imaging of heterogeneous hydraulic properties. Specifically, SA preserves transmissivity extremes and spatial complexity, both necessary for accurate conditioning of a flow simulator. Also, the stochastic continuum approach provides an avenue whereby uncertainty (or risk) may be addressed. Currently, the SA weaknesses are that it is computationally time consuming, and uncertainty may increase when simulating under conditions of statistical isotropy. Recognizing that ISLM exerts a dynamic influence on hydraulic properties with time, the mine design should be reevaluated at intervals throughout the evolution of the leaching process.

Jan 1, 1993

By A. D. Pernichele

Four types of slope failures in waste dumps are recognized; debris flow, foundation failure, edge slump and blowout. The first three types, although at times causing considerable damage to property and interfering with mine operations, are not usually dangerous to personnel because of their slow rate of movement. The fourth type, the blowout, is considered to be the most dangerous because of its explosive mode of failure and lack of forewarning. The December failure at Verona dump is presented as an example of a blowout. Data from piezometer holes indicate that the blowout was due to perched leach solutions near the face of the dump. The level of water in this zone is very closely related to the rate of leach water application on the dump. A detailed analysis of core samples indicated that the impounded water was due to a zonal accumulation of Jarosite which is associated with a buried dump surface. Drain holes proved successful in controlling perched leach solutions in the critical zone near the face of the dump. Monitoring of the water level in the perched zone is considered essential in preventing blowouts. The use of drain and piezometer holes has allowed an increase in the rate of water application on the dump while preventing additional failure.

Jan 1, 1971

By Benno Ring

"When designing segmental lining at a cross passage, modern solutions try to bear the loads transferred around the opening within the rings by using shear elements in the ring joints. Commonly used shear systems providing coupling are cam & pocket, shear keys, bicones and steel dowels. These solutions have advantages and disadvantages, but most importantly they have limits in their capacity to stabilize the lining at cross passages. With the help of 3D-FE-analyses for an opening of one segmental ring these different solutions are compared taking various ground conditions into account. As a result the capacity of the individual system is determined. Notice is made regarding the applicability of the system as well as the consequences for the design and the verification. INTRODUCTION The design of the lining at a cross passage is among the most difficult tasks when designing TBM-tunnels. At one time the bedding of the lining disappears due to the excavation behind the lining, at another the ring-structure is interrupted when parts of the lining are removed for the opening. The trick is to transfer the loads around the opening into other segments and to areas of the lining which are still supported by the ground. In the rings immediately at the cross passage this creates a distribution of forces within the segments that strongly deviates from that of the regular lining. The design needs to consider the boundary conditions of the respectively chosen solution for stiffening of the opening and its peculiarities in the modeling as well as in the verifications. In the past segments of steel or an internal strutting of steel (DAUB 2013) placed around the later openings were commonly used, see Figure 1. The application of a strutting from the outside to the rings is restricted to such circumstances when for example a connection from a shaft to the tunnel can be made in suitable ground conditions (Ring and Glomp 2012). Though steel segments provide a robust solution, they are expensive due to their laborious manufacture, the high proportion of construction steel required and the time consuming installation in the tunnel (Häfliger 2013). A strutting of steel requires extensive design and verification. The resulting structure usually weighs several tons and must be erected as well as demounted within the confined space of the tunnel, requiring suitable transport and assembly equipment. The cross section remains restricted, thus causing a bottleneck for TBM operations and hindering the works and installations for the cross passage works."

Jan 1, 2016

By Chas. F. Jackson

INTRODUCTION This paper is one of a series dealing with mining methods and costs, prepared and published under the sponsorship of the US Bureau of Mines (USBM) and made possible through the cooperation of many mining companies in the US and foreign countries. The data presented have been obtained from papers previously published by the Bureau dealing with indi¬vidual mines, from the technical press, and from infor¬mation furnished by the mining companies. DEFINITIONS Top Slicing The term top slicing is commonly applied to that method of mining in which the ore is extracted by a series of timbered slices, beginning at the capping; the slice is caved, bringing down the capping to the floor of the slice; the succeeding lower slices are mined up to the overlying mat or gob, consisting of an accumulation of timber from the upper slices and broken capping, which follows the mining progressively downward (Fig. 1). The term has also come to be applied to the mining of ore bodies only one slice thick, by a series of tim¬bered slices one beside the other. The timbers are blasted out, bringing the capping down to the floor, suc¬ceeding slices being driven alongside those already caved (Fig. 2). In USBM classifications of mining methods, top slic¬ing has been placed under the heading caved stopes. The method differs fundamentally, however, from the cav¬ing methods of mining in which the breaking of the ore itself is accomplished by caving action induced by undercutting. In top slicing the ore is broken by the ordinary methods of drilling and blasting, and only the capping is broken up by caving. Main Levels or Haulage Levels Main or haulage levels are the main extraction levels on which the ore is hauled to the shaft. These levels and the shaft constitute the preliminary development of the mine.

Jan 1, 1982

By Curtis A. Pledger, H. Lee Wimmer, I. Michael Gowring

The Upper Diamond Fork Project, as part of the Central Utah Project Completion Act, conveys water six miles from the existing Sixth Water Aqueduct to the Diamond Fork Pipeline. During design, a Value Engineering team proposed a single-tunnel alignment that would be less destructive on the environment and might have a lower life cycle cost than the proposed design of two tunnels connected by two pipelines on steep hillsides. A decision was made to include this option in the bid process as a design-build alternative. The bid for this option was the lowest and a contract was awarded. During the TBM excavation a segment of tunnel wall caved in containing large quantities of water saturated with extremely high levels of hydrogen sul?de (H2S)gas (measured at 380 to 520 ppm in the air). The Central Utah Water Conservancy District (District) in consultation with Obayashi/Clyde (Contractor) quickly developed anew plan to finish the system by incorporating parts of the original tunnel/pipeline concept and re-bid the remainder of the project as a Phase 2 Design-Build contract.

Jan 1, 2003

By P. C. O. Chukabarah

Atkinson's resistance square law is the cornerstone equation for traditional expression of energy losses in mine ventilation engineering. But the nomenclature for the various forms of energy losses are often confused for one another, misapplied or misinterpreted. These forms of energy were re-examined from thermodynamic and fluid-dynamic perspectives. Resultant expressions showed that both incompressible and compressible flow regimes in underground mines can easily be accommodated. Given the well-known three major energy forms, which are equivalent to one another but numerically unequal, corresponding equations to Atkinson's (pressure loss) for headloss and workloss were derived. The thermodynamic weight relational resistance ([w] s2/m5) associated with energy per unit weight (headloss) was dimensionalized for the first time. Also, normalized Atkinson-like equations for headlosses and worklosses were derived to ease direct computations in mine ventilation practice.

Jan 1, 1995

By Judson H. Whitman

To evaluate intelligently and to market a source of rare earth raw material, it is necessary that the producer understand the requirements of the processor and the manner in which these requirements effect the value and salability of his product. This paper will be an attempt to aid in such an understanding. The majority of rare earth processors are primarily chemical companies, not mining or metallurgical companies, as the complexities of the processing procedures are' much more chemical in nature than metallurgical. The rare earths and the rare earth industry are normally divided into two groups - the ?light? or cerium group and the ?heavy? or yttrium group. They are so named because cerium and yttrium are the most common elements in 'heir respective groups and are so divided on the basis of mineralogical and chemical characteristics. The dividing line of the two groups is not rigidly fixed but usually is considered as being between samarium (atomic number 62) and europium (atomic number 63). Although the two groups are quite similar, processing procedures differ significantly, hence most processors tend to specialize in one group or the other. There is, however, a growing tendency toward participation in both groups.

Jan 1, 1960

By J. R. Palmes

Three coal samples, selected out of eight with well characterized surface properties, were used in flocculation tests and synthetic mixture of coal and silica was used in the selective flocculation experiments. Coal wettability and flocculant type were found to have a strong effect on the flocculation results.

Jan 1, 1993

By Q. Xu

Adsorption of nonionic/anionic surfactant mixtures on kaolinite has been studied with sodium dodecylsulfate as the anionic surfactant and octaethyleneglycol mono-n-dodecylether as the nonionic surfactant. Synergistic interaction between these surfactant was found to cause adsorption of the nonionic surfactant with its hydrophilic chains protruding into the bulk, leading to substantial changes in wettability and dispersion characteristics of kaolinite. Similarly, hydrophobicity changes are observed also for silica particles upon adsorption of nonionic ethoxylated alcohols owing to possible changes in the orientation of the adsorbed surfactant molecules at the interface.

Jan 1, 1991

By Zhe Wang, Tichang Sun, Yongqiang Zhao, Zhengyao Li

Coal-based reduction followed by magnetic separation is a promising technology for processing refractory iron ores. Analysis of the size distribution of metallic iron particles is an effective approach for exploring the mechanisms of coal-based reduction. As metallic iron particles exhibit very complex shapes compared with nature ores, approaches for measuring and characterising metallic iron particles still remain unclear. In this study, the size of metallic iron particles was measured and characterised using manual point-counting by optical microscopy technics and image analysis. The effects of CaF2 as an additive on behaviour of the particle size distribution (i.e. mean size and cumulative frequency distribution) were also determined. Results indicate that CaF2 had a significant effect on the growth of metallic iron particles. When the CaF2 dosage increased from 0 to 8%, the mean size according to the area method increased from 9.03 to 16.28 μm, while the promotion effect gradually weakened and generated many fine metallic iron particles when the CaF2 dosage exceeded 8%. An increase in CaF2 dosage also led to cumulative distribution curves gradually shifting to the right mainly because F− can break the crystal structure of each phase during the carbothermic reduction of titanomagnetite and reduce the stability of the lattice structure, thus reducing the melting point and accelerating the growth of metallic iron grains. Compared to different measuring methods, the area method is a more suitable approach for measuring and characterising the size of metallic iron particles.

Sep 18, 2020

By R. Hogg

Based on a simplified model for the motion of particulate materials in horizontal, rotating cylinders, approximate expressions have been derived relating the power consumption of a tumbling mill to its dimensions and speed of rotation and to the amount and nature of the charge. The basic assumptions underlying the model are that there is no slip between the charge and the mill shell, that the free surface of the charge remains essentially planar during rotation and that there is no transfer of momentum from the material flowing down the free surface back to the mill shell. The relationships formulated from this model have been shown to be in excellent agreement with experimental results taken from the literature. While the requirements of the model are most closer met at low speeds of rotation, the results appear to be valid even for speeds up to 70-80 percent of the critical speed. Poorer agreement between theory and experiment is found when the charge consists of relatively large particles (balls) and when the filling of the mill exceeds 50 percent of the available volume. Qualitative explanations of these deviations have been offered.

Jan 1, 1971

By Hugh E. Cronin, Lok Home

THE PENETRATION RATE BASELINE DILEMMA The penetration rate is the instantaneous advance rate of a TBM in a rock tunnel. Normally expressed in feet per hour. The production rate is the penetration rate multiplied by the number of hours worked and then factored by the actual utilization of the TBM. In a given rock formation, the actual production rate is a result of many factors some of which are within the control of the contractor and some of which are based on the route selected. Factors that are within the contractors control are cutter profile, frequency of cutter changes, thrust, rotation speed, cutter spacing and the efficiency of the operation. Factors that are site (route) specific are compressive strength, fracture orientation, fracture frequency, micro- fracturing, quartz content, Moh’s hardness, Cerchar Abrasivity Brazilian Tensile Strength and Youngs Modulus of the rock. In addition the following route speci?c conditions are beyond the contractors control; rockjointing, rock stress fault zones, water in?ow and rock decomposition; all of which effect production rate. Any one of the above defined rock properties, equipment specifications and actual operating usage will change the penetration rate. Furthermore, since the rock formation changes both in content and orientation as the tunnel advances, the penetration rate is constantly varying. The current industry practice in bidding tunnels is for each contractor to individually evaluate the rock hardness and other properties and from this information develop a penetration rate. All other factors being equal, the contractor using the most optimistic penetration rate will be the low bidder and be awarded the project. As this view is by definition optimistic, invariably the rock will be harder than the low bid assessment and the contractor will request additional compensation for the changed condition. The contractor will attempt to justify his optimistic assessment as reasonable by using expert supporting analysis. The above described example which is quite common at present in the industry tends to make the most optimistic contractor (at time of bidding) the contractor selected for the project whereas it is in the owners interest to contract with the most efficient contractor not the most optimistic. This situation is similar to the Geotechnical analysis that was prevalent in the industry over twenty years ago. Many projects have experienced a significant reduction of penetration rate from that which was originally estimated. In these cases the contractor often makes a claim for extra compensation based on the difference between the actual rock encountered

Jan 1, 2003

By J. Villeneuve

Steady-state simulation has proved to be a very useful aid in designing new plants and optimizing existing ones. The algorithms and data definitions of existing simulators often, however, require a great deal of expertise for implementing a simulation-based methodology. The constraints imposed by conventional simulators are explained and the advantages of a new algorithm, the Objective-Driven Simulation, are shown. These advantages are a) an improvement in the simulation results, which enables simplifications of the methodologies used, and b) the possibility of taking into account economic objectives for plant operation, thus extending the range of application of steady-state simulation.

Jan 1, 1992

By Robert A. Blake

Introduction Sulfide copper, zinc and iron concentrates are recovered in the 5000 ton per day flotation plant operated by Cities Service Company at Copperhill, Tennessee. The heavy-sulphide ore is first ground to 50 pct. minus 200 mesh and a bulk concentrate floated. The bulk concentrate, over 60 pct. of the ore weight, is reground to 72 pct. minus 200 mesh and then treated in a selective flotation circuit to recover copper and zinc concentrates. The tailing of selective float is the iron sulphide material source for the manufacture of sulfuric acid and iron sinter. The valuable minerals in the ore are chalcopyrite, marmatitic sphalerite, pyrite, and pyrrhotite. A typical mineralogical analysis will be found in table 1. A typical material flowsheet will be found in figure 1. Shown in the flowsheet are a scavenger float on the bulk rougher tailing and a copper-talc separation unit. At times a lead-copper separation circuit has been run.

Jan 1, 1971

By Edward T. Koch

With the dramatic increase in world demand for basic raw materials, open pit mining is proceeding at an unprecedented rate. A viable demand is the ever tempting Siren's song for increased production or new facilities. When the Siren's lure is viewed against the panorama of today's world economic milieu the concomitant Scylla and Charybdis are seen in the form of high capital cost and high operating cost. If the economic realities of present day open pit mining are to show a proper return on investment, a clear and penetrating eye must be cast upon the area of mine planning. This paper deals with the problem of overburden removal. In almost every open pit mining operation overburden removal is a significant part of the capital cost and operating cost of the total operation. This paper deals with a new and unique method to affect economical overburden removal. Well known to all are the parameters surrounding draglines, shovels, and bucket wheel excavators. All of these machines require a reasonably stable soil to support them and the shovel and bucket wheel excavator require a reasonably stable bank in which to operate. Their reliability, portability and rate of production per dollar of invested capital are good.

Jan 1, 1975

By J. A. Arias

The oxidation kinetics of pyrite and refractory gold concentrates in acidified ferrous sulfate solutions in the presence of oxygen-sulfur dioxide gas mixtures has been studied. The effect of temperature, pulp density and gas composition were determined. The optimum oxidation rate was obtained at 80°C and 2 percent sulfur dioxide in the gas mixture. The oxidation of the sulfide minerals is attributed to the presence of ferric ions, which are continuously regenerated by the gas mixture. The objective of this study is to find a new hydrometallurgical method to render sulfidic refractory gold ores amenable to cyanization.

Jan 1, 1993

By Martin Knights, Geoff Featherstone, John Flanagan, David Lawrence

The proposed paper will address specific transport, engineering, environmental and community related issues concerning the current construction and future operation of Europe’s biggest urban road tunnel project—the US$500m Dublin Port Tunnel. Situated in Ireland’s capital, the three mile long, 40 ft diameter twin tunnel project encounters a range of ground conditions using TBM, Shield, Cut & Cover with diaphragm walling and major slope stabilisation and Multi-jacked pipe techniques. Where possible units of measurement are given in feet and inches.

Jan 1, 2003

By S. J. Jung

In recent years, the use of shotcrete, a practice familiar to the mining industry, has been on the increase. This research has come about because of the recognized need for a safe, easy way to line small diameter bored raises (less then 150cm). Up until now, an operator has gone down the raise and applied the concrete lining manually, using the shotcrete method of application. With an automated system, there would be no man positioned in the bore itself. All control functions could be commanded from a central location. Shotcreting in the confined space of a small diameter bored raise presents problems that can be overcome by the application of shotcrete using a remote system.

Jan 1, 1994

By John W. Straton

Following the completion of the paper presented in February, 1972, data were received from many other mines and some original respondents submitted more complete questionnaires. The computer program was changed to permit the results to reflect more clearly all the data reported by the mines. The original paper was revised to reflect the new information. There were significant changes in some numerical values, particularly where the size of the sample changed appreciably. Some limited samples considered originally in arriving at conclusions were not relied on in this revision. The revised tables and text are of the same design and format as the original paper.

Jan 1, 1972

By Egons R. Podnieks, Wallace W. Roepke

Mining technology to utilize vital lunar resources will be required for any commitment to permanent lunar basing. Lunar mining must be viewed both as a major supporting element for space resource commercialization and for creation of human settlements on lunar and planetary surfaces to support long-range space exploration. The Apollo missions to the lunar surface and results from fundamental research on analogue lunar rocks by the Bureau of Mines, and others, have provided the initial data for developing lunar mining technology. The multi-disciplinary research projected in this paper outlines the scientific and engineering needs to realize the lunar mining goals.

Jan 1, 1990