Search Documents

By Satya Harpalani, Xue Zhao

This paper discusses the results of an experimental investigation to study the release of methane in coalbeds. Absolute porosity of coal samples was first determined experimentally. Following the porosity measurement, adsorption/ desorption tests were carried out to determine the gas content of coal and the rate at which it is released. Finally, micrographs were obtained using electron microscopy and the use of a physical model, developed to explain the gas flow behavior of coal, was justified. The results of this study indicated that the measured absolute porosity of the coal sample was between 5 an 6%. This was significantly lower than the porosity estimated by comparing the micrograph area occupied by the pores and the area of observation for several micrographs, suggesting that coal has a large number of pores with a very small volume. The micrographs also clearly indicated that coal has a large interconnected network of cleats and microfractures. The adsorption/desorption experiments showed a hysteresis between the adsorption and desorption isotherms. Also, the rate of desorption was found to be strongly dependent on the particle size of the specimen.

Jan 1, 1989

By W. D. Diment

The concept of flying employees in and out of remote mine sites on a regular rotation basis, rather than establishing permanent support communities nearby, has gained increasing acceptance by mine operators, unions and regulatory agencies in Canada. The development of successful fly in/fly out programs and resultant compressed work schedules is dependent on meeting design requirements through comprehensive research of worker profiles to ensure the selection of suitable employees and the implementation of satisfactory working conditions. This paper presents an overview of Canadian mine industry practice with regard to the fly in/fly out mode of operation and compressed work schedules.

Jan 1, 1987

By S. A. Sass

The design and construction of Solvay Minerals (formerly Tenneco Minerals) Soda Ash Expansion Project, which is the world's most modern natural soda ash facility, is detailed. Along with a discussion of design considerations, the international joint venture ownership and teaming arrangement for design and construction companies is examined.

Jan 1, 1994

By F. Palmay, R. D. Gwilym, P. Eng

INTRODUCTION As the experience in Canada indicates, it is becoming more and more common to evaluate major mining projects, especially those relating to uranium, with respect to their environmental effects. As part of this evaluation public hearings are becoming the rule rather than the exception. In this area the 1970's and presumably the 1980's can be characterized as the age of "Environmental Assessments" or "Environmental Impact Statements" which form the basis of these hearings. These documents tend to require significant amounts of research, data collection and effort in their preparation, and tend to be closely scrutinized by the hearing body and by groups in opposition to the project. This opposition is becoming more organized and sophisticated. The assessment or impact document, together with the evidence supporting it during the hearings can: (a) mean the difference between a lengthy and hence costly hearing and a smoother, shorter and less expensive one, (b) result in requirements for extensive modification at the expense of the proponent to his project, (c) result in the proponent being required to carry out extensive studies, research or monitoring programs, and (d) conceivably may in certain situations result in the project actually being turned down. Therefore, while on the one hand it is important to have available technical answers to concerns relating to uranium, its associated and perceived hazards, it is getting more and more important to be able to present these answers in both a written and oral format in such a way as to meet the criticism and concerns of the opposition, be they citizens in general or special interest groups including environmental lobbyists. JURISDICTION From a Canadian perspective, the first legal question to be answered is which level of government has jurisdiction over uranium mines in general and specifically over aspects relating to the environmental effects, including the health and safety aspects, of uranium mines and

Jan 1, 1980

By M. Kawulak

The necessity to protect the environment can limit mining activities and make some areas less attractive for the prospecting and exploration of mineral deposits. In Poland, the main environmental factors that restrain Irumng are: 1. Regional A Protection of the landscape B. Protection of ground water from contamination and depletion 2. Local A Conservation of fertile soils B. Conservation of forest resources C. Preservation of natural, cultural, and historical monuments The regional factors listed above that can limit mining are presented on a map of Poland. These data, combined with maps of known and potential mineral deposits, make it possible to delineate general levels of limitation for various mining-related activities varying from "no existing environmental limitations" to "no allowed industrial activity" As an example, a compilation of such data is presented for lignite exploration and mining in Poland. Lignite deposits occur within Upper Paleocene to Upper Miocene clastic strata at depths ranging from a few to 300 m. The thickness of the lignite is generally a few meters, but can locally reach over 100 m within grabens. As a result, the overburden-to-lignite thickness ratio varies from less than 1 to over 20. Within the same Tertiary strata, and within overlying Quaternary strata, several aquifers exist that produce good quality water that may be contaminated or depleted during lignite mining. The protection of these ground waters is the main factor limiting lignite mining and should be addressed in mining and environmental policy and planning.

Jan 1, 1996

By D. M. Muir, C. Cao

Many gold ores have copper mineralisation which presents problems in a carbon-in-pulp operation. Various types of copper-gold ores and ways of tackling the problem are discussed. In some cases copper and gold can be upgraded to a concentrate by flotation; otherwise, copper or gold can be selectively leached. When both copper and gold cyanide are present in solution, it is possible to minimise copper loading onto carbon or to selectively strip the copper from the carbon. Alternative leach solutions like thiourea and bromine are discussed and results obtained with the ammonia/cyanide system are presented in the light of our present understanding of the chemistry involved.

Jan 1, 1989

By Kenneth R. Maser

In the past 30 years, great advances have taken place in the development of tunnel boring machines, raise drills, large diameter drills and blind shaft borers that have revolutionized the shaft sinking and tunneling industries. Techniques for placing concrete linings, however, have not changed significantly during this period, and still constitute a stumbling block to the achievement of the rapid construction. In the past 5 years, Foster-Miller Associates, Inc. (FMA) has been involved with the development of a remotely operated shotcrete system for lining raise drilled shafts, an Extruded Tunnel Lining System (ETLS) for lining TBM bored tunnels, and a Continuous Shaft Lining System (CSL) for lining any type of machine bored shaft. This paper presents an overview of these three developments, including capabilities and limitations, a description of the concrete production, concrete placement, and advance rate, and control subsystems, a description of the concrete mix development required for each system, a discussion of test results to date, and an assessment of the state of development of each concept. Plans for future development will also be presented.

Jan 1, 1981

By S. P. Sandoval

In 2002 the Freeport-McMoRan Technology Center undertook research to develop a lower-cost alternative to guar for cathode smoothing in copper electrowinning. The work was conducted at the Technology Center?s SXEW Test Facility located in Morenci, Arizona. Bench-scale copper electrowinning cells were designed and implemented to screen a number of potential polymers for cathode smoothing. These included modified polysaccharide polymers that were nonionic, cationic, and anionic in nature.

Jan 1, 2010

By John Waggoner, Steve Klein, John Townsend, Jay Arabshahi

The Riverside Badlands Tunnel is a 13 km (8 mile) long segment of the Inland Feeder Project. This 3.65 m (12 ft) finished diameter water tunnel presented many challenges that had to be overcome to take the project from concept to reality, not the least of which were the diverse ground conditions. Construction of the tunnel was carried out by a single tunnel boring machine (TBM) in one tunnel drive. The project is considered a success due to the accurate baseline established for the ground conditions; the approaches used to mitigate adverse conditions; and the appropriate use of TBM excavation methods, which achieved rapid advance rates despite the challenging ground conditions.

Jan 1, 2003

By III Kimball

Mining wastes have received individual attention under the Resource Conservation and Recovery Act (RCRA) since its inception, in recognition of the special characteristics that distinguish mining wastes from other solid wastes. The Environmental Protection Agency (EPA) has recognized that: - Mining wastes are generated in much larger volumes than other industrial wastes. Most material handled in mining is waste (over 99% in many cases) and not marketable product, whereas waste is a small portion of raw materials used in most industries. Consequently, controls used for hazardous wastes may be technically infeasible or economically impractical. - Nearly all mining waste is managed at the site of generation and is land-disposed. . - Mining wastes typically pose lower hazards than other industrial wastes. Mining operations are located predominantly in sparsely populated areas and in arid or semi-arid areas with little surface water runoff and deeper water tables.

Jan 1, 1990

By J. D. Miller

Reaction kinetics for gold dissolution in acid thiourea solutions were investigated using formamidine disulfide as an oxidant. For the conditions studied it appears that a surface reaction limits the rate of gold dissolution. The rate was found to be first order with respect to thiourea concentration and half order with respect to the concentration of formamidine disulfide; the apparent activation energy for the reaction was 10.40 kcal/mol (43.40 kJ/mol); and the reaction rate was independent of pH for the pH range 1.0 to 3.0.

Jan 1, 1999

By Bernard J. Scheiner, R. J. Wesely, Cy E. Jordan, A. D. Zunkel, Gary M. Wilemon

The U.S. Bureau of Mines has investigated leaching of off-grade western United States phosphate deposits using sulfuric acid (H2SO4) in the presence of methanol. A combination of ore grinding followed by sulfuric acid in methanol leaching extracted over 80 pct of the phosphate. This leaching technique significantly limited the dissolution of iron, aluminum, and magnesium impurities and produced a phosphoric acid that was well within the desired limits for these impurities. The dissolution rate of phosphate rock in the sulfuric acid methanol system was significantly slower than the conventional aqueous sulfuric acid dissolution. Initially dissolution of the phosphate particle was controlled by the amount of surface area available to the sulfuric acid reactant. After about an hour of leaching, phosphate dissolution was slowed almost to a stop, limited by the rate of ion diffusion through the calcium sulfate barrier layer surrounding the unreacted phosphate particle. Consequently, the ore was ground below 38-pm to increase the particle surface area available and improve the overall dissolution kinetics and extraction. In addition, the sulfuric acid was slowly metered into the reactor to prevent any excess heat from the mixing of acid with the methanol from simulating the formation of methyl sulfates. The formation of methyl sulfate ultimately lowered the overall phosphate extraction by exhausting the supply of available sulfate ions for the dissolution reaction. Subsequent evaporation of the methanol from the product acid decomposed the methyl sulfates leaving undesirable sulfate ions in the product acid. Slow acid addition to the reactor provided high phosphate extraction and limited the amount of sulfate in the final product acid.

Jan 1, 1993

By O. P. Sinha, Biswajit Mishra, A. K. Mandal, Raj Kumar Dishwar, G. S. Mahobia, Ram ji Omar

Most of the mineral deposits found in North-East India remain unexploited due to inadequate knowledge on their status, economic viability, and requisite mining technologies. The aimof this study is to characterize the multimetallic magnetite mineral deposit from the Nagaland area in India. The quality of iron ore was evaluated to establish its suitability as a raw material for iron production. Detailed studies were conducted to establish the composition and properties of the samples. X-ray diffraction (XRD), X-ray fluorescence (XRF), electron probe micro-analyzer (EPMA), and petrographic microscopy techniques were employed in the investigation. Shatter and tumbler test was performed for analyzing the mechanical properties of the ore. XRD studies indicated that magnetite is the major mineral with low amounts of martite, maghemite, and quartz. XRF/EPMA results indicated that magnetite contains 35–65 wt.% of iron and 1–5 wt.% of chromium. It also confirms the presence of Ni and Al up to 1 wt.% and Si up to 6 wt.%. Chromite-rich ore contains up to 30 wt.% Cr and 15–20 wt.% of Fe.

May 10, 2021

By Penglu Gan, Jinjie Zou, Chenglang Pan, Xiaowu Tang, Yu Zhao

"The north segment of the Zizhi Tunnel that consists of twin tunnels was excavated at a shallow depth in soft ground using the Shallow Tunneling Method. Based on continuous field measurements, the development histories of surface settlement were analyzed first. The observed development process could be roughly divided into three stages and the influence of river was evidenced. Transverse and longitudinal surface settlements above the twin tunnels were then fitted with empirical models. The obtained trough width parameters in transverse and longitudinal direction (it and il) and the volume loss (VLs) were presented and discussed. Additionally, surface settlement was compared with the crown settlement. The relationship between surface and crown settlement behaved in two different ways inside and outside the river-affected region. The findings in this project give references for predicting surface settlements in similar tunneling condition. INTRODUCTION Nowadays tunnel construction has become a major way of utilizing underground space in many large cities. The ground deformation will be inevitably induced in the tunneling process. Engineers should always be careful about excessive deformation that may damage adjacent structures. For shallow tunnels, controlling ground deformation turns to be more risky. Since soil arching is not completely formed in the shallow tunneling, settlements can easily develop from tunnel crown to ground surface.A conventional tunneling method named Shallow Tunneling Method (STM) has been developed and widely applied to constructed shallow tunnels in China. The major difference between this method and the New Austrian Tunneling Method (NATM) is whether considering self-supporting capacity of surrounding ground or not. In order to reduce the disturbance of surrounding soils, several guidelines are highlighted in this method, including advanced pipe forepoles, strict grouting, short excavation length, strong support, quick closure and frequent measurements (Fang 2012). Nevertheless, the ground deformation is still hard to control and becomes a concerned problem, mainly because ground settlement has some regional features and largely depends on the detailed excavation methods (bench cut method, multiple heading method, etc.) and ground condition (sand, clay, decomposed rock, etc.)."

Jan 1, 2016

By Grazyna Dziurdzak, Robert C. Dunne, James H. Kyle

The pressure pre-oxidation of refractory gold concentrate from the Golden Mile has been investigated and the conditions of temperature, oxygen pressure and percent sulphide breakdown for maximum gold extraction optimised. Both tellurides and sulphides were oxidised under optimal conditions and deposited in the residue as oxides along with haematite. Under non- optimal conditions, a reactive basic ferric sulphate was formed instead on the unreactive haematite. Maximum gold recovery after cyanidation (tail < 1 ppm) is well in excess of that produced by the present roasting process (tail 3-4 ppm).

Jan 1, 1989

By F. W. Brackebusch

In the paper presented by F.W. Brackebusch on the "Basics of paste backfill systems," paste fill was presented as a backfill process that offers many advantages over other alternatives such as hydraulic fill and rock fill. It was observed, however, that the mechanics of paste-fill transportation in pipelines is not fully understood and that the success of its implementation in practice depends on the precise control of the proportions of fines, aggregates and water in the mixture. The author emphasized the necessity for laboratory and full-scale testing to determine the suitability of a material to be used as paste fill. Although experimental testing is definitely an important operation in the design of a reliable paste fill, advances in the understanding of the fundamental laws that govern paste flow in pipelines are equally relevant. Ideally, the results of such efforts would provide predictive models for the rheology of the paste and the corresponding pumping-energy requirements. In an attempt to achieve this objective, an ongoing research program has been active at McGill University&apos;s Department of Mining and Metallurgical Engineering. Preliminary results showed that the underlying mechanics of paste-fill flow in pipelines may be described in terms of what is known as "plug flow," as depicted in Fig. 1. Although this flow mechanism has been known qualitatively for many years, few attempts managed to offer a comprehensive model (Gandhi, 1987; Duckworth, 1986). In our model, it is assumed that coarse aggregates present in the mixture form a porous core, which is filled with paste (fines and water) and is surrounded by an annular non-Newtonian (Bingham-plastic) lubrication layer, which enables the mixture to flow with pressure losses that are easily overcome by common positive-displacement pumps. In summary, our model predicts the thickness of the annular lubricating layer, which controls the magnitude of the pressure losses. This is done either by collecting data on the apparent viscosity of the Theologically-active fine fraction and using an analytical equation (Bouzaiene, 1994), or is done by measuring the void content of the coarse aggregates and deducing the thickness as a function of the fine- to coarse (weight or volume) fraction ratio in the mixture for a given pipe diameter and solids concentration. Our model predictions showed good agreement with data from Duckworth et al. (1986), as shown in Fig. 2.? References Bouzaiene, R., 1994, "Hydraulic transportation in mining," Ph.D. dissertation in progress, McGill University, Dept. of Mining and Metallurgical Engineering, Montreal, P0, Canada Duckworth, A., Addie, G.R., and Maffei, J.R.,1986, "Mine waste disposal by pipeline using a fine slurry carrier," Proceedings of the 11th International Conference on Slurry Transportation, Slurry Transport Association, Washington DC. Gandhi, R.L., 1987, "Effect of rheological properties of fines fraction on slurry hydraulics," Proceedings of the 12th International Conference on Slurry Technology, New Orleans, LA.

Jan 1, 1996

By Frank Palkovits

All technologies move through a cycle from infancy to maturity. Thickened tailings have moved into the young adulthood phase of its development. Many mining companies like the idea of reducing their water-taking and water disposal issues. This limits the risks associated with traditional surface water-covered tailings facilities and the reduced dilution possible through underground disposal of thickened or paste tailings. Just as home theater systems advertised as ?plug and play? are rarely quite that straightforward, implementing and improving a thickened-tailings system has its challenges. However, the technology has also developed in recent years so it is more accessible. Some success factors have emerged because of the new technologies. Is thickened tailings the right solution? The first step in success with thickened tailings should be whether it is, in fact, the right solution for a particular mine. And, if so, what type of thickening is best. The answer depends on several factors, including: ? Grain size: The grain size that is optimal for maximizing mill recovery is some-times not suitable for thickening. Other mineralogical factors, such as mica content, may also influence whether the tailings are suitable. ? Water issues: Available water does not always have the purity necessary for the process. Another issue to consider is that if water is in short supply, as is increasingly often the case, thickening may be a way to reduce the need to both take and dispose of water.

Jan 1, 2008

By T. McNulty

The author was privileged to find employment as a uranium mill chemist for The Anaconda Company while working his way through school in the mid-1950s. He then served Anaconda in various technical and management positions until 1980. This paper describes the prevalent technologies employed by uranium producers, briefly describes various mines and mills in the U. S., and memorializes a few of the thousands of men and women who contributed to the U. S. Uranium Boom. Following isolation of uranium as an element by M. H. Klaproth in 1789, uses of uranium were confined primarily to pigments, glass coloring agents, and ceramic glazes. In 1896, Antoine Becquerel found that uranium is radioactive, releasing particles and energy as it decays. In 1898, Pierre and Marie Curie isolated radium from uranium and learned that it can be an effective treatment for some types of cancer. In 1939, it was discovered that the isotope U235 is fissionable1 . Up to this point, nearly all uranium production was from pitchblende concentrates made in Bohemia, Canada, and the Belgian Congo. In 1938, only about 5 percent (23.85 short tons) of global output was produced from ores of the carnotite mineral that were being mined in the U.S. By the early-1950s, physicists in many countries had begun to recognize the potential for nuclear chain reactions. Ernest Rutherford (UK), Frederick Soddy (UK), and Leo Szilard (US) explained transmutation of elements and formulated the principle of “atom splitting”. In 1934, Marie Curie’s daughter, Irène, and her husband, Frédéric Joliot, identified uranium as the most viable source for this new form of energy. The basic fission process was unraveled by German scientists in December 1938. After Hitler’s army seized the uranium deposits in Czechoslovakia, many feared that Germany would build the first nuclear weapon.

Mar 2, 2022

By J. L. Uhrie

A potentially cost effective technique for the reclamation of heavy metal contaminated soils and sediments involves the technique of froth flotation. Heavy metals sorbed to clays in the soil may be sulfidized by the introduction of sodium sulfide and floated using a dithiophosphate collector. Separations were obtained where up to 78% of all copper ion was removed from the system. Selected samples were floated in a column cell but little advantage was seen.

Jan 1, 1996

By William Highton

If the economic situation in the Western World evolves on a path similar to that of the past decade, then we Mining Engineers must accept that one of the major cost factors in the production of deep mined coal is going to be that of labour. Whilst not trying to over-simplify matters it does appear that one of the ways of maintaining acceptable coal costs is by obtaining more coal without increasing manpower. One such way could be an increase in the use of the retreat method of mining. The paper theorises and illustrates case studies to show that as the Mining Industry extends the use of Longwall retreat mining systems in coal seams where the risk of spontaneous combustion exists, then the use of bleeder entries should be questioned. In addition to the spontaneous combustion risk, bleeder entry systems where the ventilation flow is not fully controllable cannot be construed as a safe and reliable method of controlling high rates of methane emission. These two major aspects alone should be sufficient ground for Mining Engineers to re-consider the practice of using bleeder entries. An alternative "The Back Return System" appears to offer most of the advantages for controlling the environment, without the disadvantages of the other system.

Jan 1, 1980