Search Documents

By R. Kealey, D. Huo, Q. Zhang, Y. A. Sari

Greenhouse gas (GHG) emissions from primary mineral and metal production account for ~10% of global GHG emissions. One of the main sources of GHG emissions in mining operations is fuel consumption by haul trucks. Given their size and carrying capacity, the fuel consumption of haul trucks can approach 250 liters per hour. An average of 30% of the idle time of the trucks is spent while waiting in the queue. Inefficient truck dispatch planning can waste resources, cause dilution and elevate GHG emissions. In this research, a machine learning based truck dispatch approach was developed to dynamically route the haul trucks based on the loaded material, the road traffic, the estimated wait time, and the maintenance needs of the trucks. The GHG reduction potential of this smart fleet management approach was estimated by calculating and comparing the related carbon emissions versus scenarios using traditional fleet allocation approaches. Results suggest that this dynamic fleet allocation approach can significantly reduce GHG emissions at mineral production sites by optimizing waiting times and the overall distance travelled while achieving the same production levels.

Mar 2, 2022

By I. R. McGowan, J. Tilk, J. I. Hershman, R. L. Lewis

The White Pine Mine is a large underground copper mine located in the Upper Peninsula of Michigan. A numerical ground water flow model of the White Pine Mine was constructed to evaluate potential engineering controls that would reduce the rate of mine-water discharge after closure. Of the passive controls evaluated, the placement of bulkheads within the mine workings was predicted to offer the greatest benefit, reducing the rate of discharge by as much as 35%.

Jan 1, 1998

By J. Brent Hiskey, Srini Raghavan

The physical chemistry of dissolution of silicate and complex oxide ores in aqueous lixiviants has been reviewed. Particular attention has been paid to the analysis of dissolution mechanisms and kinetic models and to the elucidation of the role of the porous nature of the materials on dissolution behavior. Importance of the physico-chemical characteristics of the leach residues on leaching efficiency has been discussed.

Jan 1, 1989

By P. Roghanchi

The difficulties associated with performing direct tensile strength test lead to development of indirect test methods, which are simple, less expensive, and less time consuming. Splitting tensile strength test (Brazilian test) is performed by applying two opposite concentrated compression load across the diameter of a disk specimen until the failure occurs along the loaded diameter. Theoretically, the load is applied over a small width as a line load, however, by increasing the load, the contact width between the loading jaw and the specimen increases as the specimen deforms. The main aim of this study is to investigate the stress distribution in (1) regular Brazilian specimen in traditional tests with loading jaws and (2) flattened Brazilian specimen with flat platens. A series of the splitting tensile strength tests and uniaxial compression strength tests are performed on three rock types: rhyolite, basalt, and limestone. Further, Numerical modeling studies are performed to investigate the effect of the contact between jaw and Brazilian specimen on stress distribution in the disc specimen based on the results from the experimentation. Finally, the stress distribution in the traditional Brazilian test specimen and the flattened end Brazilian test specimen were compared.

Feb 23, 2014

By Deborah A. Kramer

Although beryllium was initially discovered in 1797, it was not until 1916 that the first significant quantity of beryllium metal ingot was produced in the United States. Before 1940, most of the small quantity of beryllium metal used in the United States was supplied by Germany. Beryllium was not used in its metallic form; it was used as an alloying addition to other metals, mainly copper and nickel. World consumption of beryllium at that time was estimated to be a few hundred kilograms annually. Because of increased tensions in Europe before World War II, imports of metal from Germany ceased in 1940, and domestic production was required to meet the needs of the military. As a result, by 1946, the United States became the principal supplier of beryllium products for the world, a condition that prevails today. Because of beryllium's high strength, light weight, and high thermal conductivity, it has been used in a large number of industrial and defense applications as a metal, alloy, and oxide. The United States is the only country other than China and the former USSR currently producing beryllium products from beryllium ores and concentrates. Bertrandite, mined in Utah, is the principal ore source of domestically produced products. Imported ore, mainly from Brazil, supplements domestic ore supplies. Production and consumption data for the United States is shown in [Figs. 1 and 2]. Production data for 1969-1979 is withheld to avoid disclosing company proprietary data.

Jan 1, 1994

By B. Ainsworth

The 1972 discovery of the Howards Pass lead-zinc deposit was the product of systematic regional geochemical surveys used to evaluate conceptual geological models for the metal-rich black shales of the Selwyn Basin. Motivation of personnel involved in all aspects of work was as critical a factor to the success as the existing corporate attitudes and infrastructure. Exploration programs were flexible but maintained a focus only on targets of sufficient economic potential to support operations in remote locations. Direct costs for the programs that lead to the discovery were in the order of $500,000 (Canadian 1972). Geological reserves today stand at over 500 Mt (511 million st) of 7% combined lead-zinc, containing a higher grade zone of nearly 10 Mt (11 million st) of 16% combined lead-zinc.

Jan 1, 1991

By Gabriel de Almeida

INTRODUCTION The widespread use of desktop computers by an ever increasing number of people, both for personal and for business and government uses, has brought public attention to surprising stories about computer abuse. Before the advent of microcomputers in the information processing environment, hundreds of amazing misdeeds involving large computers had already been reported, most of them perpetrated by highly skilled professionals. The undreamed enlarging of microcomputer potential has steadily posed a major threat to complex mainframe computing systems, as joyful teenagers become familiar with the habit of hacking around someone else's large processing system, by means of makeshift phone communication networks, based on their intended homework for personal computers -- for the sheer fun of it. Now, the never ending capacity and speed improvement of commercially available micros has given rise to a brand new concern for society: the hazards of processing sensitive information in the powerful, but still unsafe microcomputer itself, whether or not linked to other micros or mainframe networks. This paper deals with some aspects of the problems and presents some practical hints as to enhance protection and minimize risks to sensitive and secretive information when processed on microcomputers. The physical considerations of computer security and pertinent safety precautions will not be discussed, because while essentially relevant to information protection, recommendations are well defined by processing resources suppliers and their importance is more widely recognized by users in general. Definitions and Classifications. The following definitions and classifications will be considered in this report: Information Assets: Any knowledge or information processing, storing or conveying device displayed in one's environment. It consists of two main categories: INFORMATION RESOURCES: End user's application data wherever recorded. PROCESSING RESOURCES: EDP skilled user's hardware, software, peripherals, magnetic media, communication devices, auxiliary equipment, supplies and related operational procedures. Information Protection: In a broad sense this is the set of necessary procedures to assure to the legitimate user the effective control of the operation and allow modifications of information assets, so that their physical or cognitive integrity be preserved or any unexpected loss minimized inspite of accidental occurrences or intentional actions. Classification Processes: Commonly two classification processes are used to define key terms in information protection: SENSITIVE CLASSIFICATION: Pre-defined standards for assessing the vulnerability to losses due to lack of proper processing continuity if information is destroyed, disclosed, secluded, or misused. SECRECY CLASSIFICATION: A spectrum of degrees as to the expectancy of holding exclusiveness of unique information whose destruction, disclosure, seclusion or misuse will cause a negative impact on the legitimate holder environment. Sensitive Information: Any knowledge whose destruction. disclosure. seclusion or misuse - - - implies losses to its legitimate holder. It may be classified as: VITAL INFORMATION: An essential knowledge whose lack of proper availability implies total loss or termination of p

Jan 1, 1987

By J. J. Kellar, W. M. Cross, J. D. Miller

Infrared spectroscopy has been one of the most useful experimental techniques for the analysis of surface reactions in flotation systems, including surface alteration and surfactant adsorption reactions. With the advent of Fourier transform infrared (FTIR) spectrometers, many low-energy throughput IR experimental techniques previously unused by flotation researchers have come into greater use. In particular, internal reflection spectroscopy (IRS) is the most often used technique for in-situ studies. To date, three IRS methods have been used for in-situ measurements. These techniques are evaluated for use in characterization of surface reactions in flotation systems. The method using mineral crystals as reactive internal reflection elements (IRE) is of particular interest because it allows surfactant adsorption densities to be calculated directly from in-situ spectral data in real time. Application of in-situ FTIR/IRS with reactive internal reflection elements will be demonstrated for collector adsorption reactions in each of the major flotation systems. The alumina (A1203)/sodium dodecylsulfate system is used as an example for insoluble oxide/silicate flotation, while the fluorite (CaF2)/oleate system serves as a paradigm for semisoluble salt flotation. For sulfide flotation, sphalerite (ZnS) is used as the reactive IRE with potassium amylxanthate and potassium ethylxanthate as collectors. In the case of soluble salt flotation, sylvite (KC1) is used as the IRE with n-octylamine as collector. Finally, the use of reactive IREs in the near-IR spectral region and in spectroelectrochemical research is discussed.

Jan 1, 1989

By Glenn L. Krum

Inflation has received much attention due to its effect on capital budgeting, associated cost overruns, and declining real profits. This study focuses on the effects of inflation on the evaluation of a mining investment and the estimation of a mining project's revenues. The study indicates that the best method for estimating future returns is the fore- cast dollar scheme. In this scheme, the metal price was held constant, and the operating costs were "inflated" along a historical regression line. The conclusion was reached by comparing the "actual" performance of a 3000 tpd (tonnes per day) lead mine model with 'its estimated performance during four time periods (1950-1960, 1955-1965, 1960-1970, 1965-1975). The individual data files for each time period and estimating method (6 files by 4 time periods) were pro- cessed by a suite of cash flow computational and investment analysis sub- routines. The analysis presumed that the mine was part of a large corporation which could utilize the expensed, development and exploration costs and any investment tax credits, in the year that they were incurred.

Jan 1, 1979

By Andrew T. MacKenzie, Paul A. Rantala

Predictive pastefill rheology (flow characteristic), models have long challenged pastefill practitioners. While the methodology and practicality of recipe formulation is attainable in most locals, the remaining challenge has been to devise a predictive mathematical or empirical model of paste flow characteristics. Flow phenomenon can now be assigned mathematical and physical basis. The authors herein disclose physical and mathematical methods that demonstrate how operators could proceed when designing reliable pastefill systems. Knowledge presented will allow users flexibility in adjusting flow-rates. Laboratory data shows stiff pastefill delivery design can be derived through mathematical relationships of particle size, material characteristics and pipe diameter.

Jan 1, 2001

By Erik Westman, Enji Sun, Xu Ma, Ben Fahrman

"Shale gas has become an increasingly important clean energy, which has been explored worldwide in recent decades. Supercritical CO2 acts as fracturing fluid for shale gas production. The safety monitoring is essential to prevent any kinds of leakage from the reservoir as the supercritical CO2 physically stored hundred kilometres underground. Seismic tomography is an imaging technique that uses induced seismic waves to create three dimensional images of the subsurface. It is an effective monitoring method to evaluate the caprock integrity in the carbon dioxide sequestration storage (CCS). In this experimental research, a simulated uniaxial compressive load is applied on a granite sample to analyze the stress redistribution for long-term in-situ caprock integrity during CO2 injection. The induced seismic waves are recorded and seismic events are traced based on the Geiger algorithm. The frequency of seismic events correlates with the caprock failure evolution. The acquired seismic data is divided into four regimes based on the frequency of seismic events and the failure process to examine the failure evolution. Furthermore, the travel time and distance is plotted to analyze the variation of velocity. Finally, the double difference tomography (TomoDD) algorithm using arrival time is adopted to recalculate the locations of seismic events and velocity structure in each regime. The results indicate that the passive seismic system can map the caprock stress distribution and allow for imaging of the caprock integrity. TomoDD exhibits sound improvements to relocate seismic events both in relative and absolute locations as well as to characterize the local velocity structure. The study further reveals that seismic monitoring along with TomoDD could evaluate the caprock failure accurately in the CCS.Introduction To reduce the CO2 concentration in the atmosphere, CO2 capture and sequestration (CCS) has been suggested to as a means of continuing to use fossil fuel resources while offsetting their negative environmental impacts (Eiken et al 2011). A positive CCS project should retain 99% of the injected supercritical CO2 (pressure is greater than 7.38 MPa and temperature is above 31.04? and a density is of about 700 kg/m3) over at least 100 years (Davidson et al 2005). As large quantities of supercritical carbon dioxide are being injected into full scale storage projects, caprock stress is redistributing and the leakage could occur anywhere over a wide storage area (Hou et al 2012). Acoustic waves are emitted from the caprock, as it fractures due to the CO2 injection, which can be detected by passive seismic sensors (Shitashima et al 2013). Tomography techniques are advantageous for imaging the integrity of the caprock in the CCS projects. Velocity tomography uses waves to model entities based on the arrival time of waves (Westman et al 2001, Westman 2004, Luxbacher et al 2008). Seismic tomography is a data inference technique that exploits information contained in seismic records to constrain 2D or 3D models of the Earth's interior. It generally requires the solution of a large inverse problem to obtain a heterogeneous seismic model that is consistent with field observations (Kudryavtsev et al 2012)."

Jan 1, 2017

By N. Edmonson

During the last 30 years, a dramatic increase in the supply of byproduct sulfur substantially reduced the share of the market held by Frasch-mined (non-by-product) sulfur in North America. Even though Canadian sulfur production is not discretionary, the geographic remoteness from the large US markets and the high transportation costs associated with delivering sulfur to those markets has meant that Canadian producers act like discretionary producers in many important ways. They have effectively replaced the US Frasch producers as the cost-marginal sulfur source to large US markets. Implications of this change in market structure include more volatile sulfur prices and longer sulfur price recessions.

Jan 1, 1997

By John Carson

Belt feeders are commonly used to meter the flow of bulk solids from bins and hoppers. If the interface between the hopper outlet and belt feeder is not designed correctly, flow from the bin may be severely compromised, resulting in problems of no-flow, segregation, flooding, etc. By knowing the flow characteristics of the bulk solid being handled and applying proven design techniques, such problems can be avoided. Relevant bulk solids flow characteristics are identified, along with measurement techniques. Design procedures for correcting problems with existing feeders as well as proper design of new feeders are presented, along with case histories of successful application of these procedures.

Jan 1, 2008

By K. R. Price, M. Gauna

Jim Walter Resources No. 4 mine produces coal through retreat longwall mining at 610 to 670 m (2000 to 2200 ft) of depth. A three entry, total yield pillar, longwall development experimental region was established for three adjacent longwall panels utilizing 6.1 m (20 ft) wide gate section pillars. Presently, the first longwall panel is completed with roadway deformational behavior monitored for a ground control assessment of the mining system. Data illustrate that the total yield pillar gate section design at No. 4 mine is presently comparable to gate section designs having large equal size chain pillars. Ground conditions will continue to be monitored during the mining of subsequent longwall panels in order to determine the ground control implications from multiple panel extraction.

Jan 1, 1986

The Longwall Strata Control and Maintenance System (LoSCoMS) is designed to monitor shield pressures in real-time from longwall faces and to provide on-line information related to underground strata behavior and longwall mining operation. The information includes shield pressure data with statistical analysis of setting, developing and final pressures, prediction of shield pressures for the following shift or day, etc. and maintenance data on the shields. The LoSCoMS has been installed and tested at Shoal Creek Mine operated by Drummond Company, Inc. The system is providing valuable information to mine operators for better understanding of underground behaviors. As a result, it has become an effective tool for minimizing ground control hazards and reducing out of seam material.

Jan 1, 1997

By Jackson G. Jenkins

Magma Copper Company's San Manuel SX-EW facility has operated since May, 1986. The original facility had a design capacity of 25,000 tons per year of electrowon copper cathode produced by processing pregnant leach solution from an open pit/heap leach operation. In 1988, the plant was expanded to 50,000 tons per year to incorporate processing in-situ leach solutions. This paper focuses primarily on the heap leaching area with regard to exploration, testing, feasibility, permitting, design and construction, and operating practices. Research utilizing surfactant leaching aids to enhance copper recovery is also discussed.

Jan 1, 1993

By Jean-Luc Cornet

Downhill, or regenerative conveyors have always been a challenge to the design engineer due to their natural instability under load. The last decade has seen the appearance of high tonnage, high negative lift conveyors with several hundred meters of drop. These conveyors have made necessary the development of new braking systems and intelligent drive controls to address their starting and stopping requirements under various load conditions. This paper describes the critical design criteria of large regenerative conveyors and some of the advances in mechanical braking systems and drive control technology developed by Conveyor Dynamics, Inc. (CDI) to address their specific requirements.

Jan 1, 1993

By X. Yin

Surface force measurements based on atomic force microscopy (AFM) are used to describe the wettability of surfaces, specifically kaolinite basal plane surfaces at a high resolution. The kaolinite particles (~500 nm) were ordered with either the silica tetrahedral face exposed or the alumina octahedral face exposed, and surface force measurements were made between a hydrophobic diamond-like-carbon (DLC) tip and the kaolinite faces at pH 4, which is around the isoelectric point of the DLC tip. Under these conditions, the effect of electrostatic interaction should be eliminated and only van der Waals interactions and hydrophobic-hydrophobic interactions are expected to contribute to the surface force. The wettabilities of the surfaces were determined from the magnitude of the surface force. Wettabilities of the kaolinite basal planes thus determined were compared with the corresponding wettabilities of talc and mica surfaces, which are well-known to be naturally hydrophobic, and hydrophilic surfaces, respectively. The results reveal that the silica tetrahedral face of kaolinte has a modest level of hydrophobicity, which may be due to the lack of hydrogen bonding sites. In contrast, the alumina octahedral face showed no hydrophobicity, since a layer of surface hydroxyl groups is present at the alumina face, resulting in a relatively strong interaction between this surface and water molecules. It is expected that, with a better understanding of the surface properties of kaolinite, further improvements in flotation separations and dewatering may be achieved.

Feb 1, 2012

By Wayne W. Murdy

Since 1993, Newmont Mining has been growing through the development 'q of three major foreign mining operations with a fourth under construction. The first project, Yanacocha in Peru, began operating in October 1993. This occurred at a time when political and business risk in that country was considered high. In 1995, Newmont began operating the Muruntau joint venture in Uzbekistan. It is the first mining project of its kind in the Confederation of Independent States (CIS). In early 1996, Newmont started operating the Minahasa Mine in Indonesia. In early 1997, Newmont began construction of a $1.9-billion project in Indonesia. The company is also completing a feasibility study with its partner for the development of a gold operation in Mexico. All of these projects have been considered "risky" by most standards. Newmont has been successful in all of them through risk mitigation programs. These programs include using strong and successful in-country partners, concentrating on developing a strong national workforce with minimal expatriate employees, using World Bank, European Bank for Reconstruction and Development (EBRD) and International Finance Corp. (IFC) financing and building and maintaining strong ties with host governments.

Jan 1, 1997

By M. J. Friedel

The scale-dependent hydraulic properties in a fractured porphyry copper oxide deposit are investigated for relevance to In Situ Leach Mining (ISLM) design. In most well field designs, mine operators assume that hydraulic properties represent a continuous spatial function, or continuum. The problem, however, is that the representative elemental volume, the volume over which hydraulic properties are described as a continuum, is a domain (if it exists) that occurs between end members representing varying degrees of heterogeneity. At the Cyprus Casa Grande mine, transmissivity fluctuations are spatially correlated. This suggests that, at the scale of ISLM, the hydraulic process is heterogeneous, and a typical continuum representation is inappropriate for design. Alternatively, a conditional stochastic approach using the Simulated Annealing (SA) technique is deemed useful for the imaging of heterogeneous hydraulic properties. Specifically, SA preserves transmissivity extremes and spatial complexity, both necessary for accurate conditioning of a flow simulator. Also, the stochastic continuum approach provides an avenue whereby uncertainty (or risk) may be addressed. Currently, the SA weaknesses are that it is computationally time consuming and that uncertainty may increase when simulating under conditions of statistical isotropy. Recognizing that ISLM exerts a dynamic influence on hydraulic properties with time, the mine design should be re-evaluated at intervals throughout the evolution of the leaching process.

Jan 1, 1994