Search Documents

By T. P. Mucho

Over the past several years, two types of roof control problems have been en- countered at Beth Energy's Eighty Four Complex mine in Southwestern Pennsylvania. These problems have been (1) poor roof conditions encountered while advancing submain entries and longwall panel entries and (2) deterioration and failure of long- wall gateroads, principally the tailgate entry. This paper discusses the efforts by mine personnel to analyze the origins of the various attempts to-deal with the problems, and the success (or failure) of these efforts. Highlighted are the use of various common roof Control materials, variations in mining techniques, cementatious pillars, and changes in pillar design using yield and abutment pillars to address these problems.

Jan 1, 1986

By Jon Bowler

Daw Mill Colliery, UK Coal, near Coventry in England, mines the Warwickshire Thick Seam at 800 m/2500 ft depth using longwall retreat with gateroads supported by rockbolts. Over the last eight years the mine has worked longer and wider panels with extraction heights of over 5 m. Recently the mine has experienced high deformation conditions principally from the rib sides resulting in operational issues and production delays. Investigation of rib deformation was undertaken using new inspection and measurement techniques, including systematic laser surveying, and improved rib support consumables were developed and introduced. A new rib trussing system using textile webbing has proved very successful.. A rib support management system was also developed and introduced for face retreat. This allowed rib support to be more effectively managed both for production and safety. For the current developments, new 28-mm-diameter roof and rib bolt systems have been introduced and rib bolt length has been increased to 3 m, with the aim of achieving gateroad stability over the life of the panel. Significant reductions in roof and rib deformation have been confirmed by the latest monitoring results. These ground control innovations are allowing Daw Mill?s potential to be realised. Production from 302?s face in 2008 set new UK and European records. However the support enhancement process continues and further innovations are planned.

Jan 1, 2009

By Peter Zhang

Shield recovery in a longwall move is normally conducted from tailgate to headgate. However, if the face is wide and the immediate roof is weak, difficult conditions with considerable roof sag, excessive shield load, and local roof falls could occur as the shield recovery proceeds to the middle of the face, causing delays in shield recovery. The situation could be aggravated when a pre-driven longwall recovery room is employed. Alternatively, a bi-directional approach for shield recovery, i.e. shield recovery starting from the middle of the face towards both tailgate and headgate, can alleviate the roof sag significantly by quickly withdrawing the shields towards the lower abutment pressure zones at the headgate and tailgate sides. In this case, the bi-directional shield recovery approach was used in a longwall move for a 1450 ft wide face under weak roof conditions. Shields were successfully withdrawn within five days without experiencing significant roof sag. The time-dependent roof-to-floor convergence, shield pressure, and roof conditions were monitored during shield recovery. 3-D finite element modeling was conducted prior to longwall move to evaluate the difference between a uni-directional and a bi-directional shield recovery during a longwall face move. Vertical stress, yield zone in and around the recovery room, load on the shields, and convergence at the center of the shield canopy were obtained from computer modeling, and compared with the data from field monitoring. Finally, the advantages of the bi-directional shield recovery are discussed.

Jan 1, 2007

By S. Paul Singh

"The long-term viability of seismically active and/or deep mining operations hinges upon the industry's ability to maintain profitability in a climate of increasingly difficult conditions, escalating operating costs and fluctuating metal prices. Within this context, it is prudent to explore mining techniques that could provide means for safer and more profitable extraction of seismically active and/or deep seated deposits that are vital to the long term survival of the industry.The first step was to examine Penetrating Cone Fracture (PCF) and other relevant concepts with the objective of semi-continuous mining in deep underground hard rock mines. This was followed by an assessment of the current conventional drilling and blasting practice. Thirteen blasts were monitored in five different seismically active workings of an operating deep mine. The main concerns during the current drill and blast practice were identified.On the basis of the literature review, three short round blasting techniques were short listed for further review. These techniques were evaluated based upon the available literature and discussions with the persons associated with their applications. Justification, requirements and major challenges for the application of short round blasting have been discussed in this paper. Suggestions for improving the current drilling and blasting practice have also been outlined.INTRODUCTIONRock fragmentation is the key to mineral excavation and production. Increasing working depths, environmental concerns and trends towards continuous mining necessitate the development of new and improved rock breakage methods.The excavation of hard rocks is still dominated by the sequential routine of face preparation, drilling, charging explosives, blasting, ventilating for fume and dust removal, mucking and roof support. Worse still, drilling and mucking require specialized equipment that fills the end of the heading so that no other operation can be performed and the equipment must be removed from the face to protect it from fly rock."

Jan 1, 2010

By Jun Lu

There are many factors affecting the strength of pillar, including width-to-height (W/H) ratio, mechanical properties of coal and surrounding rocks, property of partings in the coal, and the interface property between coal seam and the roof/floor. In this paper, the effect of varying pillar?s width-to-height ratio (W/H=3, 5, 7, and 10) and coal/rock interface cohesion (Cj =50 psi, 150 psi, and 300 psi) on pillar strength has been studied. The confinement effect of W/H ratio and interface shear strength is investigated by studying their effects on the average minimum principal stress developed in the pillar. The deformation behavior of the coal pillar is investigated. It is found that the pillar?s transition from strain softening to strain hardening behavior depends on its W/H ratio and the interface shear strength.

Jan 1, 2008

By Yuanwci Shi

This paper discusses the results of research on the interaction between roof strata and shield supports including the active and passive supporting functions of the shield supports which prevents roof strata separation; pressure distribution on the canopy and under the base plate as measured in the laboratory and underground; comparison between various shield structures regarding their effectiveness on roof and floor control; and determination of optimum support capacity under given geological and mining conditions including hard-tocave roof

Jan 1, 1997

By Christopher Mark

Knowledge of in situ stresses is fundamental to many studies in earth sciences, and coal mine ground control is no exception. During the past 20 years, it has become clear that horizontal stress is a critical factor affecting roof stability in underground coal mines. The theory of plate tectonics and the World Stress Map (WSM) project has been extremely helpful in explaining the sources and the orientations of the horizontal stresses observed underground. Recently, WSM geophysicists studying deep-seated stresses have developed a model of how stress magnitudes vary with depth in the crust. They have devoted relatively little attention to near-surface stresses, however. This paper explores the relationships between deep-seated and shallow in situ stresses in several of the world?s coalfields, using a data base of more than 350 stress measurements from underground coal mines. The analysis indicates that distinct regional trends exist, corresponding roughly to the regional stress fields identified by the WSM. The paper presents equations for estimating stress magnitudes that were developed by treating depth and elastic modulus as independent variables in regression analysis. The magnitude of the horizontal stress increases with depth, at rates that range from 0.8 to 2.0 times the vertical stress, just as the WSM ?critically stressed crust? model predicts. Overall, it seems that the stress regimes encountered in underground coal mines are closely linked to those that exist deep in the earth?s crust.

Jan 1, 2008

By Ke Yang

In Chinese coal mines, extraction of deep, highly gassy soft coal seams sandwiched between soft floor and soft roof in complicated geology is commonly encountered. How to safely and efficiently excavate such seams is a very significant and important problem. It has been a focused research area in recent years. By combining the characteristics of fully mechanized longwall mining methods such as large cutting height and mining along the dip, an integrated method and technologies for the Zhangji Coal Mine were developed. This technology includes the design of a complicated geological exploration system, optimization of mining method and working face parameters, control of rock pressure and high levels of gas, reliability model of the production system, and selection and compatibility of equipment. Engineering practice shows that the integrated technology was successful in mining these complicated seams. This study not only enriches the mining method, but also improves the coal mining practice, especially ensuring both safety and productivity under complicated geological conditions.

Jan 1, 2009

By Jiulong Cheng

Underground coal mining causes overburden deformation and failure, one major form of which is bed separation in the overburden. Surface subsidence can be controlled by injecting grout into the bed separations. For a long time, the grouting results of bed separation can not be validated. This is the problem in the application of this technique. This paper analyzes the conditions leading to bed separation, develops mathematical models for seismic wave fields generated before and after bed separation, and bed separations grouted with different materials, and computes the seismic wave field characteristics using the finite difference method. The results show that the existence of bed separation causes changes in the characteristics of seismic wave field, and that different grouting materials generate different seismic wave field characteristics. Intact strata, bed separation, and bed separation filled with air or water all display distinctive seismic wave field in amplitude and frequency spectra. After mining, the original location that provides strong seismic reflection wave no long exists. It is replaced by a weak and syncline-shaped reflection wave. The area, where the seam wave disappears, is larger than that of the mined area. The location, where a bed separation occurs, generates a set of reflection waves stronger than the normal one. The energy of the reflection waves varies with the materials filling the separations. Bed separations filled with air generate stronger reflection waves than those filled with water. The major frequencies for those filled with air are lower than those filled with water. Therefore, it is possible to determine the property of filling materials by analyzing and comparing the amplitude and frequency spectra of the reflection waves. Case studies of application of seismic method for exploring bed separations and grouting were analyzed. The results show that it is feasible to use seismic technique for exploring bed separations and grouting.

Jan 1, 2006

By David Newman

In Eastern Kentucky, the Darby seam has had an extensive history of coal bumps and pillar bursts. The combination of high overburden, strong rock and coal, subjacent and superjacent mines, and retreat mining has produced incidences of violent pillar failure. The influence of these factors on pillar stability and the potential to bump is illustrated in two case histories. In the first case history, a bump occurred unexpectedly during the retreat mining of a five heading continuous haulage panel. Alternative cut sequences and pillar dimensions were analyzed to identify a geometry that would reduce the potential for future coal bumps or bounces during retreat mining. The viability of the alternatives was constrained by the reach of the continuous haulage system, the overburden depth, and the presence of thick sandstones in the main roof. Each alternative was numerically modeled cut-by-cut to examine the mechanism of stress transfer, as a pillar row is retreat mined. This approach highlighted which cuts were being made in highly stressed portions of a pillar and therefore more prone to coal outbursts. Validation of the numerical modeling was accomplished by comparing the cuts where bumps and outbursts had occurred underground to the highly stressed cuts shown within the models. Recommendations of the barrier pillar width between adjacent panels, pillar dimensions, and changes in the retreat mining sequence were proposed based upon the overburden thickness, geology, and the result of the numerical modeling. The second case history documents a nine-entry panel 3,600-feet long that was retreat mined a distance of 2,064-feet without a significant roof fall or roof-floor convergence. Mine management became concerned about the potential for a coal bump or a large roof collapse within the gob and the resulting air blast. The stress on the pillar line and within the remnant pillars in the gob was quantified through numerical modeling. Changes in mining practices on the current panel were implemented to avoid a bump in the active panel. A barrier was established between the current and the future panels to protect the future panel against abutment pressures from the void area. A change in pillar centers was proposed in the adjacent panel to absorb the side abutment pressure from the gob of the active panel.

Jan 1, 2008

By Xiangxi Wu

Longwall and continuous mining are prevalent methods employed by Chinese underground coal operations. The main ground control challenges include roof skin deformation, roof collapse, and outbursts of coal, gas, and water. Microseismic monitoring provides valuable information on rockmass behavior and fracture propagation caused by stress redistribution, active geological structures, or gas build up within the coal strata and the surrounding rockmass. Collecting and assessing seismic data has proven to be an instructive tool for engineers to better assess ground conditions and mitigate seismic hazards associated with mining. The development of intrinsically safe and explosion proof certified seismic monitoring equipment has revolutionized China?s underground coal mines. The use of this technology allows for the optimization of gas drainage at an increased rate of two at a 50% higher purity without any increase in drilling costs. Microseismic monitoring can also be used in identifying seismically active faults and shear zones. This information can be used to assess and revise mining strategies to improve safety and ground stability.

Jan 1, 2012

By D. C. Oldroyd

Western Coalfield?s Tandsi Mine, has difficult support conditions and a history of roof falls, resulting in mining roadway widths and depths being restricted for safety reasons. Rock Mechanics Technology Ltd was contracted to improve the support system to allow the introduction of mechanised room and pillar mining. The introduction of a ?world best practice? bolting system resulted in major improvement in roof stability, allowing mining restrictions to be lifted and Tandsi to become one of the first two Indian mines to introduce a mechanised continuous miner system. The first year?s production was some six times previous levels. Because of the improvement in the support system, RMT was also able to design a partial de-pillaring system suitable for the Tandsi continuous miner districts together with the introduction of monitoring procedures and guidelines to maintain safe roof support conditions. In situ monitoring of pillar and roof behaviour was undertaken as the first pillars were extracted to confirm the design. De-pillaring operations have also proved highly productive, and to date there has been no associated support related major injury or dangerous occurrence. The success of this project demonstrates the potential for mechanised room and pillar mining in India.

Jan 1, 2006

By Jurgen te Kook

State-of-the-art for subsidence calculation are stochastical models. Although these models were successfully used all over the world they have their limitations due to the fact that they are not based on mechanical laws. For example the models did not take the rock mass structure and the rock mass characteristics into account. Therefore in a research program the skills of geomechanical numerical models for subsidence calculation were investigated. A case study shows that numerical models which are in principle based on the elastic theory are suitable for subsidence prediction. Due to the principles of these models the results are not sufficient in the case of multiple seam extraction. More extended geomechanical numerical models like FLAC and UDEC were investigated in further steps of the research work. Up to now large area geomechanical models require unrealistic long calculation times if the level of detail is similar to that of small scale calculations. Due to this it was necessary to implement a simplified description of the rock mass structure and characteristics. Different case studies show that this approach is successfull for subsidence calculation by numerical geomechanical models even for multiple seam extraction.

Jan 1, 2008

By S. Paul Singh

Rock burst is one of the most serious mining hazards, adversely affecting the safety, economy and productivity of mines. It is a sudden manifestation of the release of strain energy stored in the rock mass. At present, there is no universally accepted method for predicting the timing of the rock burst. However, if the seismically hazardous regions in mines can be identified before they are exposed to mining then precautionary measures can be planned before the work begins. A study was conducted in Sudbury Nickel Belt and an approach has been proposed to identify rock burst prone workings on the basis of (a) Rock properties and bursting indices (b) In-situ approaches (c) Geological features (d) Mining conditions (e) Observations during mining operations (f) Comparison and analogy with previous case histories of bursting. This approach will facilitate the judicious application of the burst control techniques to seismically hazardous areas.

Jan 1, 2008

By Xingtian Hui

Due to variation in the geological natures of underground coal mines, especially when the entry?s roof/floor are soft and weak, it is vital to select an appropriate roof bolting system to ensure entry stability, coal production, and miner?s safety. No single type of roof bolting system perfectly fits for various types of openings, even within a mine. From the results of continuous research on roof bolting in the past 10 years, the authors used a novel concept of ?Self-screwed? mechanism to develop five types of roof bolting under a patented Self-screwed Tube Bolting System (STBS)©. This roof tube bolting system can be applied to meet different timing-strength requirements under varying mining conditions to increases the stability of mine workings. This paper outlines the structures and mechanisms of the five types of self-screwed roof bolting systems along with their unique characteristics, advantages and disadvantages, and limitations. Two case studies using a Self-screwed Tube Drilling Bolting (STDB)©, one of the five types of roof tube bolting systems, show the principles of mechanics, suitability and parameters for a mine entry and a subway?s construction/ supports in the surrounding soil layers and soft sands, respectively are presented. The results confirmed the time dependent anchorage capacity between predictions and on-site measurements. Currently, other types of the self-screwed tube bolting systems are also being applied to different coal mines in China to increase entry stability and meet safety requirements.

Jan 1, 2009

By David Conover

Technological advancements in electronic sensors and mine-wide monitoring systems have improved remote monitoring and analysis of underground mining information. The effective use of . these systems for ground control applications, however, remains a challenge facing the mining industry. The U.S. Department of Interior, Bureau of Mines is conducting research, utilizing real-time acquisition of rock mechanics data, to provide mine operators the means to rapidly identify and manage potentially hazardous ground conditions. The Bureau has installed a remote monitoring network in a Colorado coal mine to record Pressures from instruments installed in the roof and pi1lars of gateroads and from transducers on shield-legs along the face. The field data are being monitored at the Denver Research Center, 150 mi from the mine. A computer at the Center analyzes the field data and generates graphic displays, which permit detailed examination of mine-wide ground conditions in real-time. For the first time, Bureau researchers are able to perform real-time monitoring and analysis of rock mechanics data while mining is in progress. The data collection and display capabilities of the system were effectively used to identify and evaluate face stability problems at the mine.

Jan 1, 1990

By Dennis Dolinar

Improperly designed support systems have led to unplanned roof falls in longwall tailgates. To prevent such falls requires appropriate support and adequately designed support systems. The National Institute for Occupational Safety and Health (NIOSH) is currently developing a standing support design methodology based on the ground reaction curve. To design the support system with this methodology requires a quantitative assessment of the ground and support interaction, which is developed from instrumented test sites installed in longwall tailgates. To compliment and expand the field data results and to optimize the support design, numerical modeling is also conducted. The models are calibrated from the test site data. In the present study, data was obtained from a longwall tailgate in the Illinois basin. The test site was located in the Herrin No. 6 coal seam at a depth of 500 ft. At the site, the immediate roof was a weak shale overlain by a competent limestone. Above the limestone, sandstone formed the intermediate roof. The floor consisted of a weak underclay. In the study, the performance and interaction with the surrounding rock mass of two different standing supports, an engineered crib and a conventional 4-point wood crib were monitored. The two cribs have similar load-displacement characteristics at least through 6 in of displacement. Beyond 6 in, the engineered crib becomes unstable and begins to strain soften and shed load. The measurements and developed ground reaction curves indicated that the tailgate at the mine was a low convergence environment until well inby the face. Because the convergence was well below their capacity, both supports provide more than adequate levels of support to the tailgate. Significant convergence and support loading did not occur until 90 to 100 ft inby the face. The results of this study were also compared with results from similar studies conducted in the Pittsburgh seam to further advance the development of the ?ground reaction curve? based support system design.

Jan 1, 2009

By Floyd D. Varley

Outbursts, the sudden and violent out- pouring of material into mine openings, is a ground control problem increasingly encountered in the United States as deeper seams are developed. Outbursts, caused by several mechanisms, are the result of the loading of ground support systems be- yond their designed capacity to failure, manifested in a violent release of stored energy. There are several types of outbursts typical to deep underground coal mines. - Outbursts of the coal face due to the presence of pressure abutments in close proximity to the face. These outbursts are usually accompanied by liberation of large amounts of methane. - Instantaneous convergence of the ribs and floor due to overloading and failure of ribs which lengthens the beam of floor strata sometimes resulting in a chain reaction failure of the mine floor. - violent failure of the confined core of a pillar due to rapid loading beyond the yield point of the pillar.

Jan 1, 1986

By Anthony S. Spearing

The vast majority of the estimated 100 million rock anchors installed in mines in the USA per year use resin cartridges (Tadolini and Mazzoni, 2006). About 4.5 million per annum of these are bolts with a mechanical shell that if properly installed become effective active supports on installation. In addition, cable anchors (mostly passive) are installed with typically 4 ft of effective resin anchorage length sometimes with mechanical shells, which further makes the installation more difficult. This is because the cable (even with a stiffener tube) is not very rigid. When installing bolts with mechanical shells and cable bolts in the holes, the back-pressure can be so high that the installation is unsuccessful often creating a ?spinner? (an un-tensioned bolt) at best or buckling the bolt thus requiring another bolt/cable to be installed, or leaving a poorly functioning unit. The installation problems can create a significant potential safety hazard and waste time and money. Using a purpose designed test rig that physically inserts different rock anchors into pipes with resin and measure the back-pressure developed with time during the insertion/ installation. The test installation procedure is designed to mirror that used underground by rockbolt operators in coal mines. In addition a computer model has been calibrated that can predict the approximate back pressure of new anchor and resin combinations acting as a screen before physical testing. This research has lead to an understanding and quantification of the insertion back-pressures and this already resulted in improved prototype designs that could lead to more reliable mechanical shell and resin bolt installations.

Jan 1, 2009

By A. W. Khair

This paper presents an analysis of fracture depth and intensity due to subsidence over the longwall panel. Sonic reflection techniques were utilized to determine fracture depth, and a variation of p-wave velocity was used as an indication of the fracture intensity. Instrumentation has been tested for consistency and accuracy first in the laboratory using small scale models, then applied in the field in two mine sites with different mining geometry and geologic conditions. A new sonic viewer was utilized for sonic velocity measurements. Regular hammering method was on acoustic source. The results were concurrent with monitored horizontal strain profiles and measured open fractures over the longwall panels.

Jan 1, 1989