Search Documents

By Alice Barreto Bevitori, Felipe Perissé Duarte Lopes, Denise Cristina Oliveira Nascimento, Sergio Neves Monteiro, Isabela Leão Amaral da Silva

"The piassava fiber is one of the most rigid natural lignocellulosic fibers, which has since the last decade been investigated as possible reinforcement for polymeric composites. In the present work, the tensile properties of polyester composites reinforced with piassava fibers with thinner diameters were investigated. Composites with volume fractions up to 30% of continuous and aligned piassava fibers were tensile tested at room temperature to evaluate the ultimate strength, elastic modulus and total strain. For each volume fraction, individually separated fibers with the smaller diameters were tested. The results indicated that the tensile properties tend to improve with increasing volume fraction of the thinner piassava fibers. The role played by the fiber/matrix interaction was analyzed by scanning electron microscopy.IntroductionA significant change in the transportation sectors mainly the aerospace and automotive, occurred last century with the introduction of stronger and lighter materials. The most relevant example was the polymer composite reinforced with synthetic fiber. They are nowadays replacing conventional materials such as the aluminum alloys in airplane body owing to superior specific strength. in recent years, however, environmental problems in a global scale are imposing a reversion in the use of synthetic fiber specially the glass fiber. In spite of its higher specific strength, this fiber and its polymer composites can neither be recycled nor incinerated in a thermal plant to generate electricity [1]. Moreover, the fabrication, processing and transportation of a glass fiber composite are associated with C02emission, the major responsible for global warming [2].A possible substitute for glass fiber without the above-mentioned environmental problems, could be a natural fiber. In fact, natural fibers obtained from cellulose-rich plants, also called lignocellulosic fiber, are already being used in several engineering fields, particularly the automobile industry [3-6]. Figure 1 illustrates an automobile and its many components made of lignocellulosic fiber composite [7]."

Jan 1, 2011

By Abbas H. Mirza

Arsenic and selenium are found in low quantities together with other metals in several nonferrous metallurgical process streams such as scrubber blowdown solution, acid plant wastewater, gas cleaning plant water, etc. Normally, the other metals in these streams are present as cations and can be precipitated by conventional lime treatment and sulfide polishing. However, arsenic and selenium are invariably present as anions, AsO33-and AsO43 in the case of arsenic and SeO32 and SeO42 for selenium. Conventional lime treatment removes most of the arsenic, but it does not remove selenium. The present paper reviews the processes and technologies developed to date on the removal of arsenic and selenium from metallurgical process streams.

Jan 1, 1996

By Wenliang Cao, Jidong Li, Mingjie Zhang, Yiyong Wang

In CaC12-CaF 2 System, we studied the electrode process and discharge mechanism of preparation of Al-Ca alloys by fused salt electrolysis with CaO as raw material. The change of back electromotive force after adding CaO was measured by continuous pulse oscillograph method and the discharge process mechanism was also investigated by cyclic voltammetry. The finial results indicate that back electromotive force decreases by 0.6V after CaO of 1 % is added and there was a peak of oxidation current ahead of the potential at which the negative chlorine ions precipitated. According to thermodynamic calculation, it was determined that current peak was caused by the CO2 produced by 0 2 - ionic discharge due to CaO addition.

Jan 1, 2014

By Jinjing Dua, Jun Zhua, Kuiren Liub, Bin Wang, Xiaolei Wua

V-Ti-Fe as hydrogen storage alloy was prepared by reducing metal oxides with a metallothermic reduction method. The deoxidation process of the V-Ti-Fe alloy was performed by electro-deoxidation and vacuum induction melting method, respectively. The results showed that the content of oxygen impurity can be controlled at about 0.2wt% after electrolyzing for 240min. Both the maximum values of hydrogen absorption capacity and the effective hydrogen desorption capacity are 2.65wt% and 1.01wt%, respectively. The deoxidization effect of vacuum induction melting process is more remarkable, with Ce as the reducing agent. It is found that Ce addition is beneficial for reducing the componential segregation, promoting the hydrogen absorption activation of V-Ti-Fe alloy. When m(Ce)/m(alloy) is up to 5%, the oxygen content has been reduced to 0.05wt% and the maximum hydrogen absorption capacity and the effective hydrogen desorption capacity are up to 3.36wt% and 1.85wt%, respectively.

Jan 1, 2015

By R. M. Sweetin

Detailed descriptions by operating area of the Kidd copper smelter are presented, together with accounts of complement staffing, training, and preparation activities for smelter start-up in June 1981. Concentrate tonnages smelted in the first twelve months of operation were constrained by the capacity of the furnace off-gas system. However, modifications designed and introduced over that period, plus sustained efforts by operations and maintenance personnel have resulted in stepwise improvements in smelter performance.. Consistent operation at design feed rates has been well demonstrated over the third and fourth smelter campaigns and efforts continue on further improving the continuous smelter on-line times and increasing campaign life. In November 1982., following a seventeen month preproduction period, the Kidd smelter attained full operating status.

Jan 1, 1983

By O. Forsén

In the first part of this paper is studied the behaviour of small amounts of impurity elements? in the solidification of copper anodes. In the second part the dissolution of these impure anodes in sulphate based electrolysis is discussed. The first part is introduced with practical examples, the .model of solidification of impurities during the solidification of anode copper. According to this model the solidification structures of anode copper are strongly influenced by both thermodynamic and kinetic factors. Thermodynamics determine the microstructure of anode copper, but kinetics can alter the composition of melt to such that there is formed unequilibrium structures during the solidification, especially when the residual melt is solidified. The electrolysis experiments have clarified the behaviour of impuririties in the electrochemical dissolution in sulphate. Based copper electrolysis. In this study it is widely investigated to what extent any impurity elements or oxides will dissolve. In copper electrorefining. With the aid of the electrochemtcal experiments it was possible to fulfil quantitatively the qualitative results accomplished by microstructure studies.

Jan 1, 1985

By C. M. Egert, S. Rajic

"We have developed a monolithic micro-spectrometer suitable for a variety of sensing applications including industrial process monitoring. The device consists of a solid structure with a volume less than 6 cubic centimeters. All optical components of the spectrometer including two aspheric mirrors, a diffraction grating, and entrance and exit surfaces are fabricated onto the surface of the structure. All light paths are internally contained within the structure. The result is a small, rugged spectroscopic sensor ideally suited for use as a process monitor. Due to its monolithic nature the device requires no post-fabrication alignment; nor can it be knocked out of alignment during use. Although many materials and thus wavelength regions were possible, the prototype device discussed here was produced in PMMA by precision diamond turning. However, lower cost manufacturing approaches involving injection molding are under development to produce an affordable sensor.Due to its rugged monolithic design, small footprint, and low cost the monolithic micro-spectrometer is ideally suited for distributed monitoring applications often required for industrial processes. It is expected that modified versions of this sensor designs will be required for specific applications so as to maximize the performance and resolution over the operating range. For example, the prototype device described here operates over a wavelength range of 500 nm to 1000 nm. The performance of this device as a real-time surface monitoring sensor will be discussed in detail. Our approach of using wavelength dependant scattering resulted in the reduction to practice of a miniature, monolithic, rugged, low-cost, micro-instrument in a sensor sized package. The process sensor applications community has been faced by the cost versus performance issue. Simple go/no-go sensors are typically inexpensive but they provide very limited and sometimes dubious data. Scaled down traditional instruments offer very good measurand information but are typically cost prohibitive, fragile, and still relatively large. This work will bridge the gap between these two extreme sensing alternatives."

Jan 1, 1997

By Mark William Kennedy

Modern metallurgical plants typically have complex flowsheets and operate on a continuous basis. Real time interactions within such processes can be complex and the impacts of streams such as recycles on process efficiency and stability can be highly unexpected prior to actual operation. Current desktop computing power, combined with state-of-the-art flowsheet simulation software like Metsim, allow for thorough analysis of designs to explore the interaction between operating rate, heat and mass balances and in particular the potential negative impact of recycles. Using plant information systems, it is possible to combine real plant data with simple steady state models, using dynamic data exchange links to allow for near real time de-bottlenecking of operations. Accurate analytical results can also be combined with detailed unit operations models to allow for feed-forward model-based-control. This paper will explore some examples of the application of Metsim to real world engineering and plant operational issues.

Jan 1, 2014

By D. M. Hausen

The term "auriferous pyrite" relates to an association of gold with pyrite in a variety of textural forms that affect metallurgical treatment. Extraction of the gold depends not only on the grain size and distribution of the gold in the pyrite, but also on the crystal size and surface area of the pyrite. Occlusions of medium to coarse gold may be liberated by moderately fine grinding. The amenability of finely dispersed (submicroscopic) gold depends in part on the activity of the pyrite surface for oxidation. Two types of auriferous pyrite at Carlin, Nevada, have been examined by optical microscopy and SEM methods before and after aqueous oxidation test work to show how differences in morphological features can affect rates of oxidation and amenability to gold extractions by methods of chlorination and low temperature oxidation.

Jan 1, 1981

By Sung Jin Han

Magnesia-based refractory is generally used in an electric arc furnace (EAF) due to its relatively high corrosion resistance and strength at high temperatures. However, the magnesia refractory is attacked by EAF slag and thus the lining life continuously decreases. Thus, it is significant to identify the interfacial reaction between magnesia refractory and FeO-rich EAF slags. In the present study, the influence of FeO-rich slag on the corrosion behavior of MgO refractory was evaluated. The (Fe,Mg)Oss layer was observed at the slag-refractory interface and its thickness increased with increasing content of FeO in the slag. The specific reaction phenomena and formation behavior of (Fe,Mg)Oss layer were evaluated by thermochemical computing program, FactsageTM7.0.

By C. García

Several modifications to Zaldivar's original design have been made in order to reach the design cathode production. This paper describes the modifications to the crushing, leaching, solvent extraction and electrowinning operations, which in turn have increased the production by 14.8% over the design capacity in 1999. The principal modifications were to (1) incorporate a dry pre- screening plant between the secondary and tertiary crushers to increase the percentage of fines to the piles, (2) increase the retention time of the solutions inside of the piles, and (3) increase the efficiency of the tertiary crushers to reduce the particle size of the product material. The leaching ratio was increased from 2.8 to 5.6 m3/ton. The temperature of the pregnant leach solution (PLS) was increased, the amount of acid used was reduced, and a strain of native bacteria was adapted in highly contaminated solutions. The copper concentration in the PLS was increased by more than 50% and was stabilized at this level by commissioning a process of two-stage leaching. The current density in the tankhouse was increased from an average of 2 16 to 3 17 A/m

Jan 1, 1999

By K. Yarnaguchi

In the Mitsubishi Continuous Copper Converting Furnace, calcium femte slag is used. Due to its extremely high basicity, the improvement of corrosion resistance of the refractory lining is in need. In order to clarify the corrosion mechanism and to search for a new corrosion resistant material, first, the surface snuctures of bricks corroded in molten slags were observed by EPMA. Second, the dissolution behaviors of sintered MgO-based pellets containing various oxide additives were examined. It was found that the formation and the dissolution of magnesiofemte at the surface of the bricks play an important role in their corrosion and an addition of NiO, Mn02, or Ti02 to MgO is effective in stabilizing the magnesio-femte and improving the corrosion resistance of MgO.

Jan 1, 1994

By D. Tait, M. A. Halim, V. I. Lakshmanan, R. Sridhar

Rare earth elements (REEs), nickel and cobalt find their use in developing strategic materials and their demand is consistently increasing in the world while the extractable ores of these metals are gradually depleting. Process Research ORTECH Inc. (PRO) has developed innovative mixed chloride leaching processes for the recovery of REEs from alumino-silicate ores, and nickel and cobalt from laterite ores. The addition of magnesium chloride in hydrochloric acid enhances the activity of the hydrogen ion by orders of magnitude, which permit rapid leaching rates at moderate temperature and atmospheric pressure, along with high metal recovery. Innovative solvent extraction process steps are used for the separation of these metals from pregnant leach solutions. PRO’s processes also produce value added by-product of high purity iron oxide and recycle chloride lixiviant to the leaching stage. This paper describes the leaching and separation reaction mechanisms and potential process flowsheets.

Mar 1, 2017

By Maria Margarida Lima, Maria Lucelinda Cunha, Dora Algarvio

"The main goal of the present work is the quality improvement of the recycled aggregates produced by a construction and demolition waste (C&DW) recycling facility located in Montemor-o-Novo, Portugal. The recycling process was developed on a pilot plant scale with 50 t/h of capacity. Process operations are the hammer mill comminution, magnetic separation and screening.In order to improve the knowledge on the C&DW, a characterization procedure was implemented by hand-sorting, magnetic and density separation on representative samples. On the other hand, to improve the quality of the produced aggregates, the bar screen size fractions were analysed, according to the Portuguese Standard (NP EN 933-1 2000).Wood was identified as the critical contaminant, representing 17% by weight of the total contaminants. Sieving results showed that about 97%, 76%, 56%, 98% and 57% were on the correct size range, which lower results are probably due to the type of screens and/or the material characteristics of the recycled aggregates.IntroductionThe construction and demolition waste problemConstruction and demolition waste (C&DW) is generated by the construction activity, resulting from both, buildings or other structures construction and old structures demolition. As a reference, it can be told that C&DW comprises about 40 to 50% of rubbish (concrete, asphalt, bricks, blocks and dirt), 20 to 30% of wood and related products and 20 to 30% of miscellaneous wastes [1]. In Portugal, C&DW is classified in the LER (Portuguese nick name for the European Waste List), Chapter 17, and includes a diversity of wastes, like concrete, bricks, ceramics, bricks, wood, glass, plaster, copper, zinc, lead, iron, steel, as well as insulation and roofing materials. C&DW stream has several characteristics which make it particularly difficult to deal with and are summarized in the following five items.(1) Lack of information on quantities generated: In Portugal, the C&DW sector has been neglected over the past years, which meant that there are not consistent information concerning the quantities and composition of these wastes yet. Several estimates, based in different assumptions, indicate different results, which may vary from 219 Mt to 10 931 Mt [2]."

Jan 1, 2008

A novel process is being developed for metal recovery from waste electrical and electronic equipment involving a leach reactor coupled to an electrochemical reactor. Metals such as Ag, Au, Cu, Pb, Pd, Sn etc. are dissolved from shredded electronic scrap in an acidic aqueous chloride electrolyte by oxidising them with aqueous dissolved chlorine species. In the electrochemical reactor: (i) chlorine is generated at the anode for use as the oxidant in the leach reactor, and, simultaneously, (ii) at the cathode, the dissolved metals are electrodeposited from the leach solution. The extended Butler-Volmer equation was used to provide predictions of the electrode potential dependences of partial current densities and, hence, total current densities, current efficiencies and alloy compositions for acidic aqueous chloride electrolytes containing Ag(I), Au(III), Cu(II), Pb(II), Pd(IV) and Sn(IV) species, together with dissolved chlorine. With judicious choice of kinetic parameters, the predicted total current density ? electrode potential behaviour of such solutions was in good agreement with experimental data for a rotating Pt disc electrode. Reduction of dissolved chlorine at a Pt rotating disc electrode exhibited mass transport controlled behaviour, in agreement with Levich?s equation over the potential range 0.3-0.9 V (SHE). This could form the basis of a linear sensor, possibly using a microelectrode for measurement and control of the dissolved chlorine concentration in the efflux of leach reactors and inlet to electrowinning reactors in the envisaged process.

Jan 1, 2003

By Zdzislaw Miczkowski

At KGHM Polska Miedz S.A, a direct flash smelting process is used for smelting of chalcocite concentrate for the production of blister copper. The paper presents a model of complex oxidation process of single concentrate grains smelted at KGHM. The description covers main chemical reactions, phenomena of heat and mass exchange inside the grains and between a grain and the surrounding space. In the model, two zones describing the course of process inside the grain were distinguished: ? The first one, which moves faster towards the centre of a grain, both organic and carbonate carbon are freed, The process takes place without the presence of oxygen and results in an increase of the temperature in the core of the particle. ?The second zone moves slower into the grain and the rate of the movement is determined by the presence of oxygen, In that zone the sulphur is eliminated and the oxidation of the organic compounds vapours moving from deeper layers of a grain takes place. Based on the results of laboratory tests, the coefficients that describe the oxygen transportation into the grain and decide the progress in the chemical reaction were determined, The paper contains the results of model calculations for single grains reacting in environment of various content of oxygen as well as the results of model calculations for the laboratory reactor system.

Jan 1, 2003

By Giuseppe Bonifazi

Minerographic and petrochemical research was carried out on crude ore samples from the complex polymetallic Zn-Cu-Pb sulfide ores of , Sotiel in Huelva province west of Seville, Spain. A computerized image analysis system was used to define the structural and textural characteristics of the ore to obtain information on the degree of liberation of the different minerals (i.e. pyrite, sphalerite, galena, chalcopyrite). Techniques of digital multispectral image processing of reflected light microscopy images were used. Particular structures were identified by means of mineral associations and numerically quantified to obtain useful information for designing beneficiation processes.

Jan 1, 1991

By Varadajan Seshadri

Kambara Reactor (KR) consists of a ladle where pig iron is stirred by an impeller during addition of a flux powder. The objective is to improve agitation leading to dispersion, of the flux powder, in the molten pig iron in order to improve desulfurization of the liquid melt by improving solid liquid interaction. The life of the impeller is limited as it is subjected to abrasion at high temperatures. The shape and design of the impeller also has an effect on the performance of this reactor. A 1:7 scale cold model of a KR unit of the Companhia Siderurgica de Tuberao ,one of the integrated steel plants in Brazil was constructed in order to evaluate the mixing and mass transfer conditions. Mixing efficiency was investigated by tracer additions and subsequent measurement of conductivity. Mass transfer in the reactor was assessed through iodine transfer between water and kerosene and employing a macroscopic model. Mixing depends on impeller shape and depth of immersion The role of dispersion is highlighted by faster kinetics when impeller velocity is increased. The results enable assessment of design aspects of the impeller on the process.

Jan 1, 2006

By Carolina G. D. Ribeiro, Carlos Maurício Vieira, Jordana Ferreira, Sergio N. Monteiro, Janaina da S. Vieira, Cláudio R. Marciano, Natália de O. R. Maciel, Frederico M. Margem

One of today’s biggest concerns has been environmental issues, which has motivated researchers and the development of materials from renewable resources and environmentally friendly. Natural fibers have excelled in replacing synthetic fibers used in composites manufacturing, because natural fibers are biodegradable, abundance in the nature, low cost, low density, high strength, among others. Due to these qualities, some natural fibers are used for many purposes in automobile industry. However, the natural fiber has irregularities and pores in its structure which directly impact the density determination by geometric techniquesand, accordingly, the volume of fibers used in composites. Therefore, the main objective is this study is to determine the density of curaua fiber by pycnometry and to compare it with the commonly used geometric technique.

Mar 1, 2017

By Robert D. Pehlke

"Current continuous casting processes are going through a rapid evolution of advances and new developments. At the same time, intense efforts are being directed to the development of radical new technologies such as continuous casting of thin slabs and strip steel.Traditionally, the casting processes for steel have been anticipated by the development and implementation of processes in the non-ferrous industry. This trend is reviewed and what it may portend for steel is described.IntroductionThe continuous casting of steel has been a widely adopted process in the production of steel. The concepts for this processing go back into the early and mid 1800's; however, commerical development was delayed for a variety of reasons until the mid twentieth century.Beginning in the early 1960's, adoption of continuous casting was initiated and continues at this point in time to be accelerated. In Japan, more than 90% of the steel produced is continuously cast (1). More than 50% of the steel produced in the United States is continuously cast and this fraction continues to rise (2). Numerous examples can be cited of installations costing well over $200,000,000 which have provided a payoff in less than a year and a half. As this process has continued to be applied and its technology to increase, computer control systems have been installed. In particular, in the larger plants producing slabs, sophisticated computer systems involving the integration and networking of mini-computers, micro-computers, and mainframe including back-up systems at all levels are being utilized. Pehlke (3), and Harabuchi and Pehlke (4) have described the structure of these systems."

Jan 1, 1988