Search Documents

By Zhitong Sui

Based on several case studies on the precipitating behavior of valuable nonferrous metal compounds (VNMC) in molten slags a green technology for the recovery of VNMC from molten slags was proposed. This technology involves three steps: (I) The selective enrichment of the dispersed VNMC into the designed mineral phase in the molten slag; (2) The selective coarsening of the designed mineral phase to a critical grain size in the molten slag; (3) The selective separation from tailing of the grown mineral phase in the solidified slag by dressing or hydrometallurgy processes. This is a clean and low cost technique and has a great capacity to deal with a large quantity of slags. The utilization of the recovered VNMC such as Titanium, Boron, Vanadium compounds was summarized as examples of application. It was confirmed by experiments that the precipitating behavior of the designed mineral phases like Perovskite(CaTiO3), Suanite(2MgO*B2O3) and Sincosite(CaOoV2O5*P2O5) in molten slags is obviously affected by operation factors such as temperature, chemical composition, heat-treatment, additives and so on. The precipitating kinetics and mechanism of the VNMC from molten slags during solidification processes were also investigated.

Jan 1, 2003

By C. G. Bastos Andrade, F. R. Valenzuela Diaz, S. M. Toffoli

The climate change observed in the last decades, the increase of global warming, the melting of the polar ice caps, and the sea level rise have in common the non-sustainable development as causative agent. Different nations have mobilized joint efforts with the objectives of minimizing the impact of greenhouse gas (GHG) emissions, investing in the research and the development of new technologies in recycling, in biomaterials, environmentally friendly processes, and new fuel alternatives. This paper evaluates the efficiency of a Brazilian bentonite modified by acid attack, in the purification step of a waste oil to be used for biofuel production, that is, diesel from waste cooking oil (WCO). The following characterization test swere performed: XRD, CEC, XRF, SEM/EDS, specific surface area (BET), stereomicrography, kinematic viscosity, and spectrophotometry at 440 nm. The modified bentonite exhibited good purification capacity for WCO when compared to a commercial product.

Mar 1, 2018

By Sven Eck, Andreas Ludwig, Menghuai Wu

"Phase separation is a frequently occurring phenomenon during solidification accompanied by melt convection, sedimentation or, in the case of two unmixable liquids, a Marangoni driven motion. In order to describe these phase separation phenomena a two-phase volume-averaging model was employed for globular equiaxed solidification of binary alloys and decomposition and solidification of hypermonotectic alloys. The model considers nucleation and growth of equiaxed grains or second phase droplets, motion and sedimentation of grains or droplets, feeding flow and solute transport by diffusion and convection. It allows the prediction of macro segregations and the distributions of grain size or droplet size. Evaluations were made by comparing the numerical predictions with experimental results. For example it is shown that the numerically predicted grain size distribution in a plate casting (Al-4wt%Cu) agrees reasonably well with the experimental analyses.IntroductionModeling of metallurgical processes is a rapidly expanding field and the research activities in the last decades cover a wide range of areas including melt pre-treatment, solidification and subsequent manufacturing routes. Among those activities solidification stands in the central position, because the primary structure of the materials, and even many defects such as porosity, (macro or micro) segregation and inclusions form during solidification. Those primarily formed structures or defects once existing are difficult to be removed or modified by the subsequent material processing.Solidification is a multi-disciplinary field involving thermodynamics, fluid dynamics and solid mechanics, heat and mass transfer, and other disciplinesr1 -31• One of the most challenging problems in solidification modeling is the complex interactions between physical phenomena occurring on different length scales ranging from atomic rearrangement over single crystal-melt interactions to heat extraction, momentum and species transport at the system level. Modeling an industry process on atomic scale is umealistic, even on grain scale (e.g. phase field method) it would need another 40 years to be able to model the exact grain morphology in a casting space envelope of 10x10x10 cm3 [ 4]. Therefore, the realistic models for industry process are based on the solution of the macro transport equations (mass, momentum, enthalpy and species) on system scale. The microscopic phenomena such as thermodynamics, nucleation law, crystal growth kinetics and interactions at the liquid-solid interface are considered with simplified models, which are coupled with the macroscopic transport equations."

Jan 1, 2004

By E. A. Thiers

The causes of structural changes in the markets for high technology alloying metals are discussed in terms of technological, economic, and financial trends. Recent market imbalances have affected producers in developed and developing countries differently. Possible response strategies for suppliers in the two types of countries are examined that may alleviate future market imbalances.

Jan 1, 1988

By T. T. Chen

Copper anodes generated from copper scrap are relatively rich in Sn, Zn and Fe. Because of the presence of oxygen, only trace amounts of Sn occur in solid solution in the copper crystals. Thus, Sn occurs mainly as SnO2, Cu-Sn-Ni oxide and Sn-Ni-Zn oxide in the copper anodes, and Zn and Fe occur mainly as minor constituents in the Sn-Ni-Zn oxide and Cu-Sn-Ni oxide. During electrorefining, these oxide species are liberated from the copper anodes and report directly to the anode slimes. The trace amounts of Sn present in solid solution in the copper crystals dissolve but reprecipitate as Sn arsenate or a Sb-As-Sn-O phase. Accordingly, high Sn contents in copper anodes do not lead to elevated Sn concentrations in the electrolyte.

Jan 1, 2010

By Valentine A. Chanturiya

The aim of this paper is basically to show progress in the study of nanosecond processes involved in the disintegration and breaking-up of mineral complexes with fine noble metals. We studied the influence of nanosecond High-Power Electromagnetic Pulses (HPEMP) on the physical and technological properties of refractory gold-containing ores and beneficiation products. Experimental data are presented to confirm the formation of breakdown channels and selective disintegration of mineral complexes as a result of pulse irradiation, which makes for efficient access of lixiviant solutions to precious metal grains and enhanced precious metal recovery into lixivia during leaching. Preliminary processing of gravity concentrate with a HPEMP resulted in significant increase of gold and silver extraction into lixivia during the cyanidation stage, with gold recovery increased by ~31% (from 51.2% in a blank test to 82.3% after irradiation). Gold recovery from stale gold-containing dressing tailings products increased after pulses-irradiation from 8-12% to 80-90%.

Jan 1, 2006

By Kathie Mcgregor, Muhamad Firdaus, Nathan A. S. Webster, Yvonne Durandet, W. John Rankin, M. Akbar Rhamdhani

There is a growing interest in recycling/recovery of rare earth elements from permanent magnets. A number of processing techniques are currently being developed but are highly sensitive to the oxidation state of the material. The oxidation microstructure of NdFeB magnets is studied at high temperatures (773-1173 K) to understand oxide formation mechanisms and support the development of viable recycling strategies.

Mar 1, 2017

By Liangying Wen, Jian Xu, Dongdong Wang, Kaihui Ma, Yang Xu

Slags play an important role in blast furnace operation, and their com- positions are based on the CaO –SiO2–MgO–Al2O3 quaternary system. However, there is not a clear understanding of the effects of gangue on of the formation of FeO-bearing primary-slags process in blast furnace. In this work, the softening and dripping experiments under the blast furnace conditions are designed to explore the influences of CaO-/SiO 2-/MgO-/Al2O3 on the softening and melting properties of FeO respectively. The results indicate that additions of CaO or Al2O3 decrease the starting softening temperature and no dripping behaviors are found in comparison with the base case results when only FeO is used. On the contrary, the addition of SiO2 or MgO rises the starting and ending softening temperature, as well as the dripping temperature. The lowest maximum pressure drop is obtained in the case with addition of SiO2. According to XRD analysis results, the initial phase with CaO addition in the primary-slags should be CaOFe3O4 and that with SiO2, MgO, Al2O3 additions are fayalite (2FeOSiO2), magnesioferrite (MgOFeO), hercynite (FeO2Al2O3), respectively.

Mar 1, 2017

By Akihide Hosokawa

The void growth and coalescence in model materials involving a pre-existing three dimensional void array (i.e. multiple layers of a void array) was studied by X-ray computed tomography (XCT) coupled with in situ tensile deformation. To reduce the recording time, a new technique called fast tomography was employed. The model materials used in this paper were fabricated by the combination of an ultra-short pulsed laser machining system and a diffusion bonding technique, and two different types of arrays were prepared namely, FCC 1 and FCC 2 type array. This methodology allowed the authors to capture the entire process of growth and coalescence events of a void array embedded in the metal matrix. The failures in the both materials involved internal necking and shear localization. One of the highlights of this paper is that the plastic strain at the onset of void coalescence was measured for each model material. These values are in fact the adequate values to be compared with the coalescence strain predicted by existing void coalescence models such as the Brown and Embury model, the Thomason model and the Pardoen and Hutchinson model. The comparison suggested that the Brown and Embury model underestimated the coalescence in neither of the current model materials, while the Thomason model and the Pardoen and Hutchinson model showed a quite good agreement with the result for FCC 1 material. On the other hand the result from FCC 2 material agreed with none of the models probably due to the geometry of the void array that is not compatible with the existing models.

Jan 1, 2010

By Zhou Wenbin

In this paper the mechanical properties of high carbon equivalent cast iron for automobile brake discs were analyzed through thermal analysis curves. Experiment results show that the mechanical properties have a strong correlation with thermal analysis curves and an effective way to predict the mechanical properties of high carbon equivalent cast iron was proposed based on the features of thermal analysis curves.

Jan 1, 2010

By E. Fockedey

he destruction of free cyanide on a Co3O4 doped carbon felt was studied. The experiments were done with an eiectrochemical filter press cell on dilute alkaline solutions containing 250 mg/l NaCN. No chloride ions were added to the solutions. The cobalt oxide protects the felt against corrosion and has a catalytic effect on the degradation of the cyanide. This kind of electrode allows working with current density as high as 1200 Aim without any visible degradation of the felt. The most interesting results were obtained with a current density of 400 Aim' at which the cyanide concentration can be lowered to 5 mg/l with a current efficiency of more than 70 % and a specific energy consumption of about 10 kWh/ kg CN.

Jan 1, 1998

By P. A. Olubambi1

Representative samples of the hydrothermal vein deposits of the bulk complex sulphide ore deposit, 10 km south of Ishiagu, in Ebonyin State, South Eastern part of Nigeria were collected from two small scale mining companies. The samples were mixed and successively crushed in a jaw crusher and cone crusher, and ground in a rod mill. Characterization was carried out with SEM, EDX, XRD, XRF and ICP-OES. Mineralogical analysis revealed the presence of sphalerite, galena, siderite, pyrite, quartz and chalcopyrite. X-ray Diffractometry showed that sphalerite mineral in the ore occurs as sphalerite ferrous with varied percentage of Zn and Fe within the various sizes while chalcopyrite occurs as a chalcopyrite group mineral with chemical formula Cu2MnSnS4. Results of the elemental analysis showed variations in elemental composition within the different sizes.

Jan 1, 2006

By Itsuki Uehara, Hiroyuki T. Takeshita, Tetsuo Sakai, Nobuhiro Kuriyama, Hideaki Tanaka

"AB5 type hydrogen storage alloys (A: rare earths, B: transition metals) are extensively applied to a negative electrode of a nickel metal hydride (Ni-MH) rechargeable battery for portable electric equipments, electric vehicles, hybrid vehicles etc. Performance of a hydrogen storage alloy electrode is affected by various factors, microstructure and surface composition of the alloy and structure of the electrode as well as composition of the alloy. Control of those factors enables us to commercialize the Ni-MH battery in various field.IntroductionA Nickel-metal hydride (Ni-MH) battery has been extensively developed because of (1) good compatibility with a nickel cadmium (Ni-Cd) battery, (2) high energy density (1.5-2 times higher per unit volume than a Ni-Cd battery) and high dischargeability, and (3) low environmental pollution. The charge/ discharge reactions can be written as [l, 2,3]:(+) Ni(OH)2+OH- = NiOOH+H2O+e· (E=+0.490V NHE),(-) l/6LaNi5+H2O+e-· = 1/6LaNi5H6+OH- (E=-0.828V NHE),where E° is a standard potential of an electrode vs. normal hydrogen electrode (NHE). Because of the above advantages of a Ni-MH battery, the battery have been widely used as a power source of portable computers, cellular phones, electric vehicles (Toyota ""LAV4L EV"", Honda ""EV Plus"" etc.) etc. Some hybride vehicles (Toyota ""Prius"" and Honda ""INSIGHT"") and fuel cell vhehicles (Toyota ""FCEV"") are power-assisted by a high-power Ni-MH battery. In 1999, the production of Ni-MH batteries reached 870 million cells in Japan. Most of commercialized NiMH batteries are incorporated with rare-earth-based AB5-type hydrogen storage alloy as a negative_ electrode. The production of rare-earth-based alloy is estimated to be approximately 8000 tons.The battery performances of the Ni-MH battery, for example, capacity, durability (cycle life), dischargeability (kinetics) and selfdischarge, ate closely related to the metal hydride· (MH) electrode, especially, the hydrogen storage alloy in the electrode. Substitution of alloy components, heat treatment, and surface treatment in order to change surface and bulk structure of hydrogen storage alloys have been examined by us and many reseachers in order to improve the performances of MH electrodes. This paper is a review of our and their efforts to improve performances of MH electrodes."

Jan 1, 2000

By Tian Sugui

By means of the measurement of the enduring property and microstructure observation, an investigation has been made into the influences of the element Re and TCP phase on the enduring property of the single crystal nickel base superalloys. Results show that the needle-like TCP phase is precipitated along the <110> orientation on {111} planes in Re-containing/free superalloys during the long term aging, the TCP phase is identified as µ phase, and the precipitated µ phase in 4.5%Re alloy is gradually spheroidized during aging. Thereinto, the needle-like µ phase may obviously decrease the enduring lifetimes of the alloys due to the consumption of the refractory elements and the effect of the stress concentration. But the stress concentration is not easily generated in the regions near the spherical-like µ phase, which is a main reason of reducing the enduring lifetime of 4.5%Re alloy to a small extent.

Jan 1, 2010

By Jr. Foot

The Bureau of Mines, U.S. Department of the Interior, investigated flotation methods for recovering fluorite and byproduct beryllium from the Fish Creek deposit of Nevada. The preferred method includes (l) fluorite rougher and cleaner flotation, (2) de sliming at 20 micrometers, (3) muscovite flotation, (4) silicate flotation, (5) hypochlorite wash of silicate concentrate, and (6) beryllium rougher and cleaner flotation from the silicate concentrate, Laboratory results showed that over 94 pct of. the fluorite was recovered in a concentrate containing 96 pct CaFz. Beryllium flotation produced .concentrates .containing in excess of 5 pct BeO with recoveries over 70 pct. A 1.00-lb/h continuous flotation unit was constructed to demonstrate this procedure,

Jan 1, 1985

By F. H. (Sam) Froes, C. Suryanarayana, K. C. Russell, C. M. Ward-Close

"Far from equilibrium synthesis allows development of novel crystal structures and microstructures, leading to achievement of enhanced physical and mechanical properties. A number of ""far from equilibrium"" techniques are reviewed with emphasis on the amount of departure from equilibrium. The ability of two such techniques, mechanical alloying (MAl, and physical vapor deposition (PVD) to develop novel structures are discussed in detail. For the MA process emphasis is placed on intermetallic compound compositions. Solubility extension, beyond rapid solidification (RS) levels, is found in terminal compositions but not for the intermetallics. Nanostructure-sized grains (< 100nm) form which can be retained after ""low temperature"" compaction. On continued milling in many cases the nanometer-sized grains transform to an amorphous structure. Ordering is destroyed by MA, except in those intermetallics with large negative enthalpies of formation. For the PVD process, a review of application to terminal light alloy compositions is presented. This includes a new high-temperature aluminum alloy, layered materials with nanometer spacing, corrosion-resistant magnesium alloys and low-density titanium compositions. IntroductionTo enhance the mechanical property combinations of advanced structural materials innovations in process/synthesis are required [1-6]. In this paper the capability of various ""far from equilibrium"" synthesis techniques [7,8] to produce novel constitutional and microstructural effects, and hence potentially enhanced physical and mechanical properties, in advanced materials is presented. The application of two such methods, mechanical alloying (MA) and physical vapor deposition (PVD) is discussed in detail. For the MA process emphasis is on intermetallic compositions with consideration given to solid solubility extension, microstructural refinement, amorphization, and formation of intermetallic compounds. For the PVD process application to terminal light alloy compositions is discussed."

Jan 1, 1994

By Steve Johnston, Mowafak Al-Jassim, Fei Yan, Omar Sidelkheir, Alain Blosse, Katherine Zaunbrecher

"Imaging techniques are applied to multi-crystalline silicon wafers and solar cells throughout the production process. Photoluminescence imaging, both band-to-band and defect-band, is used to characterize defects and wafer quality at all process steps. These steps include bricks sawn from ingots, wafer sawing, cleaning and texturing, emitter diffusion, edge isolation and glass removal, anti-reflective coating/passivation, and metallization of finished cells. Bricks, wafers, and cells can be imaged at a rate commensurate with in-line measurement, giving spatial information to characterize quality and defect content. Photoluminescence images on silicon bricks can be correlated to lifetime measured by photoconductive decay and could be used for high-resolution characterization of material before wafers are cut. The defect areas in as-cut wafers are compared to imaging results from electroluminescence and lock-in thermography, and cell parameters of near-neighbor finished cells, showing correlations to efficiency, open-circuit voltage, and short-circuit current.IntroductionImaging techniques can rapidly characterize material quality and defect density. Photoluminescence (PL) imaging can be applied to silicon from the brick level to all wafer process steps [1-8]. At the brick level, material thickness allows for measurement and correlation to lifetime where surface recombination effects are minimized [6, 7]. At the as-cut wafer level where thin unpassivated wafers prevent accurate lifetime assessment due to surfaces, defects can still be categorized and quantified to predict finished cell performance [3-5]. Defect regions can be identified by recombination-limited band-to-band PL or by defect-band emission [9-12]."

Jan 1, 2012

By Lianjun Liu, Ying Li, Qianyi Zhang

"Photocatalytic reduction of CO2 by H2O for production of Cl fuels (CO and CH4) was studied using copper and iodine co-modified TiO2 (Cu-IffiO2) nanocomposites, with copper deposited on the surface and iodine doped in the lattice. The nanocomposites were prepared via a combined hydrothermal and wet impregnation process. All I-doped samples demonstrated visible light activity. Under UV-vis irradiation, co-modification of Cu and I significantly increased TiO2 photoactivity compared with bare TiO2 or those modified with only one species.IntroductionThe photoreduction of CO2 into fuels on photocatalysts such as TiO2 has been regarded as an important approach to solve both energy shortage and globe warming problems [1]. However, the wide band gap and fast recombination ofphotoinduced hole (h+) and electrons (e"") limited the application of TiO2 in CO2 photoreduction reaction. Extensive research has been conducted to improve the photocatalytic ability ofTiO2 by depositing or doping foreign ions that can enhance charge transfer and/or creates intra-band-gap states to induce visible light absorption at the subband- gap energy. Compared with mono-doping, co-doping of metal/nonmetal species has been reported to have higher photocatalytic activity for TiO2 [1-3]. Our previous studies showed that Cu deposited on TiO2 [4] or iodine doped in TiO2 [5] significantly enhanced the catalytic efficiency for CO2 photoreduction and increased the response to visible light. We hypothesize that there could be a synergetic effect if TiO2 is co-modified by both Cu and I species resulting in further improvement in CO2 reduction efficiency. In this work, we synthesized and characterized Cu-IffiO2 samples and investigated their activity toward CO2 reduction under visible and UV-vis illumination, respectively.Experimental MethodsMaterialsTitanium tetra-isopropoxide (TTIP, 98%) and isopropanol (C3HsO, 99.8%) were purchased from Acros Organic. Iodic acid (HIO3,99.8%) and Copper Chloride (CuCh, 99.9%) were purchased from Alfa Aesar. All other chemicals were analytical grade and used without further treatment."

Jan 1, 2012

By T. Wang, R. G. Reddy

"The corrosion of stainless steel SS316L in a low melting point novel LiNO3-NaNO3-KNO3- NaNO2 eutectic molten salt mixture was investigated at 695K. After long-term isothermal dipping corrosion experiments, the SS316L samples were analyzed using scanning electron microscopy (SEM) equipped with energy dispersive spectrometer (EDS) to determine the topography and corrosion products. Dense and protective lithium iron oxide scale formed on the surface and prevented the SS316L sample from further severe corrosion. Therefore, SS316L is considered to be suitable construction material for solar thermal energy storage materials containers.IntroductionMolten salt mixtures have been considered as potential candidates for thermal energy storage and heat transfer media in solar energy applications. To apply the molten salt in the energy transfer process, the standard pipes made of stainless steel must be utilized to carry the molten salt mixtures in parabolic trough system of solar power production. The pipes encounter continuous flow of hot and cold molten salt every day. Thus corrosion of stainless steel in molten salt mixtures becomes extremely essential for the long-term utilization of the thermal energy storage media. The corrosion of passivity materials inside high temperature molten salt systems have been studied which gives fundamental understanding of basic mechanism about the corrosion process [1-8].The corrosion behavior of Fe-Ni-Cr alloys in an equi-molar LiNO3–NaNO3–KNO3 mixture was studied [9]. According to the XRD analyses, the major phases in the oxide scales were identified as LiFeO2, Fe3O4 and Cr2O3. A HITEC® salt mixture (NaNO3–NaNO2–KNO3) was also tested as a corrosion medium for stainless steel [10] and the corrosion rate was found to be affected by the protective oxide layer. In most cases, the alloys having more than 10wt% chromium show high resistance to corrosion in molten salts."

Jan 1, 2014

By Joseph Hamuyuni, Pekka Taskinen

We present experimental results for the liquidus in the system Cu2O - CaO -Al2O3 at 1250 oC. In this study, we quantified the liquidus by the equilibration/quench/analysis technique, with Cu2O, Al2O3, and CaO as primary materials exclusively. Experiments were conducted in air at an at oxygen pressure (p) = 21.3 kPa). Equilibrated specimens were quenched in brine solution of 10 wt% NaCl. We then quantified the liquid chemical compositions by means of Energy-Dispersive X-Ray Spectroscopy (EDS) and Electron probe micro-analyzer (EPMA). This study reveals inconsistences in liquidus surface of the present ternary diagram of the system here in mentioned. Differences of up to 10 wt % compositions of the species have been observed.

Jan 1, 2015