Search Documents

By J. Krzyzanowska

Paper written on project work carried out in partial fulfilment of Bachelor of Engineering-Mining Venetia Mine, an open-pit diamond mining operation in the Limpopo Province of South Africa, currently has a mixed haul truck fleet consisting of Caterpillar 785B and C; 789C; modified 793D and 793D. Even in an ideal situation these trucks have different cycle times, which causes queuing at the loading area and their different speeds cause bunching on the ramps, leading to higher overall cycle times and lower productivity. This problem was identified but the root causes of the problem were not investigated and quantified. A time and motion study on the haul trucks was thus undertaken to measure actual cycle times and compare them to ideal cycle times as well as to observe any reasons for deviations. Ideal cycle times are partly evaluated on the basis of simulation and partly from production optimization expert input. Several areas that affect production were identified and these include: haul road conditions, the control room, dispatching programme and dispatching data management, as well as truck-shovel matching. The investigation was important in establishing control parameters for haul fleet operation since time spent queuing is production time lost, which defers waste tonnes to later in the life of mine, thus decreasing the tempo at which kimberlite is exposed.

Jan 1, 2007

By M. A. Trvits, M. Cummins, A. C. Smith, T. P. Mucho

This paper evaluates the effectiveness of remotely applied nitrogen-enhanced foam to aid in efforts to isolate and suppress a mine fire. The foam, in combination with a remotely-installed cementitious mine seal and a novel borehole pressure sampling methodology to determine the location of the suspected ignition source, was used to help control ventilation and inert the area surrounding the suspected ignition source by isolating it from oxygen. This allowed mine rescue teams to safely enter the mine, seal the area, and begin recovery operations to successfully return the mine to full production.

By David Dardick

Tround International Inc. is developing rock excavation and drilling devices which utilize a simple patented mechanism for firing frangible projectiles. This system launches a salvo of three projectiles with every shot in automatic sequence. Studies conducted by Physics International Inc. have demonstrated that firing projectiles into hard rock such as granite creates fragmentation which is much faster and cheaper than conventional drilling and blasting. The Tround salvo approach enhances this further by a controlled stresswave interaction created by a slight time difference during impact of the individual projectiles. The University of Maryland is conducting additional studies to optimize these parameters.

Jan 1, 1981

By Wolf-R. Under

For improvement of urban traffic infrastructure, the City of Amsterdam is cur­rently constructing the 9.5 km long North-South Metro line passing through the central districts of Amsterdam. Focal section of the project is the Central Station linking the NS Line with the Central Railway Station, the East Metro line, new bus and tramway terminals, ferries and individual traffic. Construction works required for the project are of high complexity and technical standards. They are executed under severe restrictions concerning programming, space, logistics, and impact on the integrity of existing buildings and structures as all existing installations and facilities have to maintain fully operational during the construction period. The paper deals with the main geotechnical features of the project and in particular with the diaphragm wall and bored pile construction at the Voor-plein and the De Ruijterkade sections of the Central Station.

Jan 1, 2006

By Leandro de Arruda Santos

O objetivo deste trabalho é contribuir no desenvolvimento de novas soluções para a terapia endodôntica através do uso da análise por elementos finitos para avaliar o comportamento mecânico de instrumentos endodônticos. Primeiramente comparou-se os resultados de testes de flexão e torção com simulações realizadas sob as mesmas condições para validação. Uma vez validada a metodologia, pôde-se avaliar o comportamento de uma lima de NiTi CM em comparação a outras duas de aço inoxidável e NiTi superelástico com mesma geometria. As geometrias de dois instrumentos endodônticos comercialmente disponíveis foram submetidas a microtomografia computadorizada para a construção de modelos 3D. A malha de elementos finitos em ABAQUS e as condições de contorno foram baseadas em ensaios experimentais de flexão e torção de limas. Os modelos constitutivos foram obtidos a partir de curvas tensão-deformação em fios de NiTi superelástco, NiTi CM e aço inoxidável. Os resultados mostraram uma boa concordância entre resultados experimentais e simulados. O instrumento de NiTi CM apresentou-se como o mais flexível em comparação aos instrumentos de NiTi superelástico e aço inoxidável.

Aug 16, 2017

By Jane Applegate

This report documents efforts to design, develop and test a training approach which would assist front-end loader operators in the acquisition of skills and awareness to reduce the probability of their involvement in accidents in the mining environment. The goal of this project was to prepare and use (on a trial basis) a training method and materials which would be generally applicable to any loader and surface mining operation while at the same time, be adjustable by mine personnel to meet the specific needs of each mining operation. This effort resulted in the Front-End Loader Training System, a structured, performance-based training approach with diverse instructional aids and classroom and on-machine training experiences. Validation of the System at a large western mine demonstrated the utility and flexibility of the training approach and materials.

Jan 1, 1983

The spatial distribution of copper grades at the Mansa Mina project is highly variable due to the presence of high grade copper/silver/arsenic breccia bodies. Copper grades within the breccia bodies tend to average about 4.5% copper while grades in the surrounding stockwork average about 1.0%. The breccia is known to occur in the vicinity of significant controlling structures, however, the outline and therefore the thickness of the bodies are far from regular. Due to the high grade of these bodies a significant proportion of the value of the project is derived from the breccia tonnages. The irregularity in the outlines/thickness translates into an uncertainty in the breccia tonnage and therefore in the value of the project. Acknowledging the economic importance of the breccia bodies and the risk associated with the breccia tonnage uncertainty, significant additional drilling has been proposed to both understand the spatial distribution of the breccias and reduce project risk. The costs associated with this additional drilling are not inconsequential; thus, a reasonable question is ‘what value is derived from this additional drilling’? To obtain an answer to this important question, a simulation approach is applied. First the deposit is simulated using the existing drilling and the uncertainty in the resource is defined. Next the proposed drilling program is simulated and the simulated data are added to the existing data. Using this expanded data set a second simulation of the deposit is created and once again the uncertainty in the resource is defined. Using this approach, the reduction in the uncertainty in the resource can be determined. To convert this reduction in uncertainty (or reduction in risk) in the stated resource into a dollar value, a method of defining the increase in the project rate of return necessary to account for risk is presented. Using the two different rates of return, the difference in project NPV and hence the value of additional drilling is determined.

Jan 1, 2003

By D. F. Malan

In deep level hard rock mining the rheological behaviour of the rock is important as time-dependent aseismic processes can lead to a stable dissipation of energy thus reducing violent outbursts. Underground closure measurements, observations of time-dependent fracture formation and siesmic data indicate that the rock in deep South African gold mines shows significant time-dependent behaviour. The objective of this work is to quantify the time-dependent rock behaviour for laboratory specimens and underground conditions. Laboratory experiments indicated that lava and quartzite specimens undergo measurable creep strain at stress magnitudes below the failure stress. Quartzite is however prone to more significant creep at lower stress levels. A viscoelastic analysis showed that laboratory creep results can not fully explain the behaviour observed underground. The in situ behaviour is governed mainly by the rheological behaviour of the fracture zone and the resulting time-dependent formation of new fractures. A viscoplastic discontinuity model implemented in a boundary element program is used to simulate this behaviour.

Jan 1, 1997

By J. Bruce Clemmer

In the experimental concentration of Vermont talc-magnesite ores, talc concentrates and tailings rich in magnesite were obtained. On account of the possible market value of the magnesite, the tailings are given consideration' in this report along with the talc. After some comments about the talc industry, the magnesite that accrued as tailings will be considered. Then the flotation results will follow.

Jan 1, 1936

By W. G. Pariseau

Introduction Caverns of 50 m in linear dimension at depths below 2300 m with a life of more than 25 years are proposed for the next generation of water-filled neutrino detectors. Little precedent exists for excavations in such an extreme environment, although some guidance is available from mining experience at great depths, for example, in South Africa, in Canada and at the former Homestake Mine in the U.S.A. Unlike mining for ore, there are choices available in the construction of such caverns that may mean the difference between success and failure. These choices should be informed by rock engineering principles. Recently proposed guidelines for orientation of brick-shaped caverns where the long dimension is a small multiple of the short dimension indicate that the most favorable orientation is with the long and short dimensions parallel to major and minor preexcavation principal stresses (Pariseau, 2005). Numerical analyses at reduced strength indicate some yielding at cavern walls should be expected but that an equilibrium state is quite possible and is aided by arching the back into a spherical dome when the cavern is an empty cylinder (Tesarik and others, 2002). The same indications of stability occur with brick-shaped caverns. However, the most dangerous situation occurs during the excavation sequence to final cavern dimensions. There are any number of excavation sequences that lead to the same final cavern shape, so there is an opportunity to partially optimize the sequence with construction guidelines that minimize peak stress concentrations during construction. This contribution discusses three practical excavation sequences that lead to the same brick-shaped cavern in the strong, massive Yates formation at the Homestake Mine where considerable rock mechanics data has accumulated through the years(e.g., Pariseau, 1985, Pariseau and others, 1995) and where actual mining on the 8000 Level indicates a strong possibility of successful investment in the next generation of large, deep neutrino detectors. The main results are: (1) a favorable brick-shape is one with dimensions in the same proportion as the preexcavation principal stresses (compressionpositive), and (2) favorable orientation of the most extreme but temporary shape of excavation is also best for the construction sequence. Analysis results from a mix of Homestake Mine data and possible excavation geometry illustrate the advantages of these guidelines.

Jan 1, 2006

By K. D. Russ, A. J. Beer

Non-contact systems for measuring underground voids have used theodolites, reflective or non-reflective laser methods and sonar techniques. An effective but cheaper alternative is based on use of a Wild T1000 electronic theodolite coupled to a Leica Data DISTO and a Wild GRE3 data logger. The software used to process the theodolite data is a spreadsheet and macro combination, while Surpac, Datamine and AutoCAD modelling packages have been investigated for viewing the tunnel profiles. The main limitations were found to be blinding, when irregularities in the stope obstructed the line of sight, and the 30 m range of the Data DISTO model used in the study, although more powerful models are available. All three modelling packages proved suitable, with Surpac providing the best-quality printed images of the voids surveyed and AutoCad by far the cheapest alternative

Jun 21, 1905

By S. Parada, P. T. Jones, M. Guo, S. Smets

The corrosion behaviour of a high-quality rebonded magnesia-chromite refractory in contact with a vacuum oxygen decarburization (VOD) slag with high Al2O3content (15?20 mass per cent) is investigated under VOD process conditions by rotating finger tests in a vacuum induction furnace. The refractory degradation mechanisms are studied by the characterization of corroded microstructures using scanning electron microscopy, equipped with energy dispersive spectroscopy. The influence on the refractory wear of the process temperature and the Al2O3content in the slag is discussed. Keywords: corrosion, magnesia-chromite refractory, VOD slags, vacuum induction furnace

Jan 1, 2004

By J. A. Finch, Zhenghe Xu

The competitive adsorption of xanthates on sulphide minerals in a binary mineral system (pentlandite and pyrrhotite) was studied using the pseudo-in-situ technique of attenuated total-reflectance FTIR spectroscopy. The minerals were placed in the same collector solutions, either separated by a glass wall or in direct contact with each other before magnetic separation and separate analysis. The effect of mineral interaction on xanthate adsorption was clearly demonstrated spectroscopically for the first time. At low concentrations of xanthate, its adsorption on pentlandite was activated by physical contact with pyrrhotite; the effect may be attributed to the enhancement of electron transfer through electrical contact between the two minerals. The results emphasise the need for caution in extrapolating results obtained from single-mineral studies to flotation practice

Jun 18, 1905

A comparatively new and very promIsmg field for applying cemented tungsten-carbides is in the mining and quarrying industries. The economic advantages of this unique engineering material over the conventional hollow drill steel, or steel detachable bits, have proven so great that the use of "hard metals" promises, in some instances, to revolutionise the drilling of all manner of minerals. Early in the war years the Germans realised the tremendous advantages cemented carbides offered for holing hard rocks, and they proceeded to develop detachable percussion bits to do this work, at the same time evolving fast, comparatively light-hitting driliing machines, especially designed to suit the mechanical properties of the carbide.Here in Australia also, it has appeared that the detachable percussion bit offers the greatest economic benefits to consumers, although the author is well aware that carbide-tipped drill rods have, and may continue to work out satisfactorily in certain mines and quarries.Most drilling equipment at present installed in Australia may be described as being of the heavy hard-hitting variety, so that the designer of an efficient percussion bit has to take special precautions to overcome the problem of fatigue, and to ensure that the inserts are securely mounted in the body with the minimum of internal stress in the carbide.

Jan 1, 1950

By A. W. Dougall, T. M. Mmola

"SynopsisThe global resources and commodities market has become highly competitive. While southern Africa’s abundance of minerals resources is still unrivalled, it has lost considerable dominance in terms of production output. The sustainability of southern Africa’s mining industry is increasingly becoming dependent on its ability to manage the performance of its operations well. A valuable tool for monitoring and managing performance is the use of key performance areas (KPAs) – which are those areas of performance that are reflected explicitly or implicitly in the vision and strategies of an organization and reflect the critical success factors of the organization. This paper is a review of key performance areas in the southern African mining delivery environment. The KPAs discussed in this paper have been identified by comparing KPAs of the several mining houses engaged in surface mining operations in southern Africa and then extracting those KPAs that are common to most of them. Although the authors support the view that each organization should develop KPAs to specifically fit its needs, the study reveals that five KPAs – safety and health, costs, product quality, fleet management, and delivery should form a default list that covers the key areas that any organization should consider when choosing KPAs. KPIs are those subsets of KPAs that we measure in order to manage KPAs.IntroductionThe global resources and commodities market has become highly competitive. While southern Africa’s abundance of minerals resources is still unrivalled, it has lost considerable dominance in terms of production output. The sustainability of southern Africa’s mining industry is increasingly becoming dependent on its ability to manage the performance of its operations well. A valuable tool for monitoring and managing performance is the use of key performance areas (KPAs), which are ‘those areas of performance that are reflected explicitly or implicitly in the vision and strategies of the organization’ (Barker, 1997). The terms KPA and KPI (key performance indicator) are often used interchangeably – whether correctly or erroneously is debatable. KPIs are ‘quantifiable measurements, agreed to beforehand, that reflect the critical success factors of an organization’ (O’Neill, 2007). Each KPA probably has multiple KPIs associated with it."

Jan 1, 2015

By D. M. Milovic

On the basis of relatively large number of field load tests of piles, the determination of the ultimate bearing capacity have been studied. Using the load settlement curves and the results of the cone or standard penetrat­ion tests, the ultimate bearing capacity was determined by Van der Veen?s, Mazurkiewicz?s and bilinear approximation method. Also, the evaluation of the modulus of deformation and the unit skin friction has been discussed.

Jan 1, 2010

By J M. Totterdell

The Permian-Triassic Bowen Basin and the Jurassic-Cretaceous Surat Basin evolved in a backarc tectonic setting behind an active convergent plate margin in eastern Gondwana. Several extensional (Early Permian; Eocene) and contractional (mid-Permian; Early Triassic; Middle-Late Triassic; early Late Cretaceous) intraplate deformational events are recognised in the basins. These can be correlated with similar events in the New England Orogen that was being deformed in the Late Permian-Late Triassic as a foreland thrust belt. The intraplate deformations were probably the consequence of plate interactions, including the accretion of terranes, at the ancient active plate margin, remnants of which now occur in New Zealand.

Jan 1, 1995

By R. B. Pedersen, A. Filipa, A. Marques

"Shallow-depth (<200m) high temperature submarine hydrothermal systems are not commonly observed on mid-ocean ridge settings, as most known systems are located within arc - island-arc volcanic settings, often proximal to coastal areas (meteoric waters added). In 2013, during the Centre for Geobiology’s 2013 oceanographic cruise (R/V G.O. Sars), a dredge successfully sampled massive sulfides and hydrothermally altered rocks from the top of a volcanic edifice (~144-284 m depth) located on the northern sector of the Kolbeinsey Ridge. Dredged samples include vesicular altered basalts, and matrix supported anhydrite, barite and barite-pyrite-anhydrite volcaniclastic breccias. Sulfidesulfate breccias depict complex zoning where numerous small vent orifices are distributed with large blades of marcasite that appear intergrown with barite. Native sulfur was observed in one of these small vent orifices. On a microscopic scale, numerous spherical silica-rich structures appear associated to these breccias. These rocks are evidence for the presence of a relatively high temperature (minimum 150ºC) shallow-water seafloor hydrothermal system in the Arctic mid-ocean ridge, far from mainland influence. This new discovery presents a unique opportunity to study the dynamics of fluid chemistry, metal mobility and precipitation in shallow hydrothermal systems. The remote location of this system dictates that fluid recharge will be influenced solely by seawater and magmatic fluids, In July-August 2014 we expect to survey this new field and acquire new and comprehensive data."

Sep 1, 2014

By A. G. Mayton

Vehicle vibration exposure has been linked to chronic back pain and low back symptoms among agricultural tractor drivers. The objectives of this study by the National Institute for Occupational Safety and Health (NIOSH) were to assess driver whole body vibration (WBV) exposures and recommend interventions to reduce the risk of back related injuries, particularly relative to vehicle jarring/jolting (the transient mechanical shock components of WBV). The methodology included collecting, from two independent samples, ?eld data and health and work history data of farm equipment operators. Data were collected during mowing, raking, baling, chiseling, tilling, and road travel for different model tractors. Spraying using a sprayer and shrub removal with a skid steer loader were also included. Based on ISO 2631 (1985), the American Conference of Governmental Industrial Hygienists, threshold limit values, presents 0.5 m/s2 as the action level recommended by the Commission of European Communities for overall weighted total RMS acceleration (vector sum for axes x, y, and z) [ACGIH, 2006. Threshold limit values and biological exposure indices. Cincinnati, OH]. WBV measured at the operator/seat interface exceeded this action level. The roughest rides and highest vector sum accelerations occurred with small utility tractor mowers (3.3 and 2.8 m/s2) and a skid steer loader (1.7 m/s2). Major ?ndings from health and work history data showed 96% of participants reported having to bend or twist their necks, although 24% reported neck symptoms. Sixty four percent of participating operators reported experiencing back symptoms (e.g., pain, aching, stiffness, etc.). Recommendations included: specifying a seat that ??better?? isolates operators from jars/jolts with new tractor purchases; maintaining the seat/seat suspension and replacing worn or damaged cushions with NIOSH tested viscoelastic foam padding; using larger diameter tires with radial ply instead of bias ply construction, particularly on small utility tractor mowers, to aid in attenuating ride ??roughness??; using a swivel seat to reduce the stress on the neck from bending or twisting; and improving efforts to educate owner/operators of the adverse effects of WBV exposures. Since the data presented in this paper were collected from two independent samples, the authors were unable to draw any correlations or etiological inferences from the study. However, results were compared and contrasted with other studies which included similar vibration measurements in agriculture.

Jan 1, 2008

By Robert Parker

Measurements of the latent heat of transformation from a to 0 titanium were made using a pulse-heating technique. Rapid heating was accomplished electrically by discharging a low-inductance capci-tor hank through a thin-strip specimen. Both high-purity titanium and titanium containing 2700 ppm of 0 were studied. An electrical-resistivity technique and a plot of energy input us temperature rise were used to monitor the phase change. It was concluded that: 1) the latent heat of transformation is 800 i 48 cal per mole; 2) phase change occurred in less than 200 sec; and 3) the percentage phase change that occurs is linearly a function of the energy available for phase change. In addition, this experiment provides a simple and inexpensive method for determining specific heat of electrical conductors over large temperature ranges. The chief advantages of this technique over past pulse-heating experiments are: 1) static measurements of capacitor-bank voltage capacitance and specimen resistance can be made quickly and accurately to determine the energy supplied to the specimen; 2) the specimen is heated so rapidly (10 µ sec) that there is no appreciable heat loss during the heating. THE purpose of this paper is to illustrate the use of the capacitor bank as a tool for basic experimental investigations and to determine the rapid phase-change kinetics of titanium. The capacitor provides a number of unique properties: 1) rapid heating rates in the order of l09oC per sec can be obtained; heating rates as slow as l04oC per sec are available by merely adding a given amount of inductance to the circuit; 2) the energy input can be precisely determined and can be varied from several joules to millions of joules, depending on the bank capacitance and voltage; 3) the specimen can be heated uniformly through the thickness and length or non-uniformly, as desired; 4) the apparatus is simple and inexpensive and can be easily altered; 5) the form of the specimen can be wires, sheets, foils, rods, and cylinders; 6) there is great precision in the timing of events; 7) this technique may be readily used in conjunction with rapid cooling.

Jan 1, 1965