Search Documents

By Fernanda Borba Simões

Na produção de biocombustíveis a partir de óleos vegetais produzidos via craqueamento térmico-catalítico, é realizada a desacidificação do produto final para sua viabilidade, podendo ser efetuada pela adsorção. Os adsorventes são diversificados e vão desde zeólitas até o uso de resíduos industriais. Este trabalho buscou testar a lama vermelha previamente ativada quimicamente e termicamente como adsorvente de ácidos graxos livres presentes no gasóleo leve produzido a partir do craqueamento do óleo de palma com índice de acidez inicial de 55,1257 mg de KOH/g. A lama vermelha foi utilizada em cinco condições: seca sem tratamento, ativada quimicamente (pré-tratada a 400°C/2h) por solução de HCl a 37%, de H2O2 a 4%, de HCl a 1,5 M e de KOH a 1,5 M. Na cinética de adsorção, a lama vermelha ativada por solução de HCl a 1,5 M mostrou-se mais eficiente que os demais adsorventes, pois reduziu o índice de acidez do biocombustível de 10,7574 mg de KOH/g para 9,1752 mg de KOH/g no tempo de 50 minutos. Quanto à eficiência dos adsorventes restantes, no que tange a desacidificação, apenas a lama vermelha seca e a ativada quimicamente por KOH a 1,5 M apresentaram remoção dos ácidos graxos livres perceptíveis.

Aug 16, 2017

By C. Taschereau, G. A. Vickell, A. R. Laplante

Evidence in support of an iron-gold corrosion cell during the high-temperature/highpressure elution of loaded carbon is presented herein including, but not limited to, its discovery, mode of genesis, and confirmatory laboratory testwork. A discussion of metallurgical and economic impacts, remedial investigations, plant design considerations, and future work including mitigative possibilities is presented.

Jan 1, 2006

By A Webster, T Murphy

Block cave mining, in its broadest sense, has transitioned from an orebody/rock mass determined method of extraction, to a low-cost and high production mining method that may be applied to any large ore deposit. This inherently means that caving is now required in more complex rock mass conditions where assistive damage, through preconditioning, may be necessary. This requires comprehensive understanding of the geology, and its interwoven relationship with geotechnical parameters, and is made more challenging due to limited exposure in block cave mines. Limited mine development throughout the cave volume equates to a heavy reliance on drilling data in terms of observations, modelling of the mine geology, and collection of geotechnical data. This translates as increased uncertainty of geological and geotechnical models and has potential to impact significantly on the ability to make informed decisions in the design and operation of the cave mine.Modelling of cave propagation behaviour requires a complex, coupled system of draw of material, flow of material through the cave stocks, and propagation of the cave-back assisted by autogenic stress-related breakage of the rock mass, manifested as seismicity. The role of geological features in the process of cave propagation is not well understood and requires evaluation on a mine-specific basis, given the diversity of geological controls/settings of ore deposits and local variability of stress fields.Seismic monitoring systems can elucidate key geological features and domains, as heterogeneous seismogenic activity is observed ahead of the advancing cave-back. The observations made from analysis of seismic monitoring data may have potential to be used as a validation tool for numerical modelling of predicted cave behaviour in similar geological settings (eg next lift/panel).Understanding of the geological structure, at all scales, is critical to optimise the design and operating decisions made in a block cave operation. At present, intermediate-scale structure, anisotropy, mineralogy and model uncertainty may be neglected or under-represented despite their likely significant role in the mechanisms of cave propagation.Insights from an analysis of the Ridgeway Deeps block cave mine are discussed in this paper.CITATION:Murphy, T, Webster, A and Chitombo, G, 2016. Beyond rock mass characterisation – the impact of geology on block cave mining, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 861–872 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Thomas J. Witzig

This Bureau of Mines report is a background study of the International Tin Agreement. Attempts at stabilizing the tin market prior to the agreement are detailed, as well as the conditions and negotiations that set up the agreement. Details of the five consecutive 5-year agreements beginning in 1956 are presented, with emphasis on membership and the agreements' primary tools: the buffer stock and export controls, Attention is focused throughout on the United States activities during the period, especially with regard to its strategic stockpile, and its involvement with the agreement culminating in its membership, for the first time, in the fifth agreement beginning in 1976. Considerations leading to the U.S. decision to join are detailed, and U.S. activities in the negotiations for the sixth agreement are presented. The status and outlook for the agreement are discussed, and evaluations of the effectiveness of the agreement and its components are reviewed.

Jan 1, 1981

By S. R. Zimmerley

Recent investigations of finely ground materials have verified Rittinger's law of crushing.4, This law states that the surface produced is proportional to the work expended in the crushing operation. Thus, for a unit of work applied to crushing quartz a definite amount of surface will be produced. Obviously, this amount of work applied to some other mineral will not produce equivalent surface. It follows that in an investigation of mill practice, where ore is being crashed, the relative crushing resistance of the component minerals must be known. In a previous investigation of the Rittinger law,5 the crashing resistance that is, the work required to produce a unit of surface - was accurately determined for quartz. The surface values were obtained by means of the rite of dissolution of quartz in hydrofluoric acid.6 If it were possible so to measure surface on other minerals the determination of relative crushing, resistance would be a simple matter; however, the results obtained on minerals other than quartz by a dissolution method were not encouraging. Moreover, if accurate values could be obtained by dissolution this method could probably never be used on a mixture of minerals such as occurs in an ore.

Jan 1, 1929

By Reda M. Bakeer

"An approach slab is the roadway segment that immediately follows a bridge intended to provide a smooth transition between the two elements. Some approach slabs have developed rough rideability with time due to differential settlement between the roadway embankment and the bridge. Soils in south Louisiana are generally poor and highly compressible and, therefore, pile-supported approach slabs were occasionally used. Timber piles of variable lengths are driven into the soft soils where no appreciable toe support exists. This resulted in the soils both supporting loads through shaft resistance and yet experiencing long-term consolidation settlement. Field testing and review of the records of over 120 approach slabs constructed in south Louisiana yielded the conclusion that their performance is primarily governed by negative skin friction (downdrag) imposed on the relatively short timber piles. A software (TU-DRAG) was developed to evaluate the deflection profile of a pile-supported approach slab based on its geometry and conditions of the underlying soils. It evaluates the effect of dragload considering the number and spacing of the piles at each transverse row and their variable lengths along the approach slab. TU-DRAG was utilized in the design of two transportation related projects which have been in service for more than 10 years.INTRODUCTIONThe problem of differential settlement at bridge approaches or “the bump at the bridge” has been recognized for many years. Research studies (1986, 1989, 1997, 2009 and 2013) by the Transportation Research Board (TRB) and the Federal Highway Administration (FHWA) provided comprehensive evaluations of the performance of bridge approach slabs by assessing their field conditions and construction and maintenance records. Various states have also performed their own studies to investigate the performance of bridge approach slabs. The studies considered various types of structures including soil- and pile-supported approach slabs, integral bridge abutments and open-end abutments. Recommendations were provided for the design of new structures and for maintaining and repairing existing structures. Guidelines were offered regarding tolerable movements of bridges and their foundations based on measurements of vertical and horizontal movements of 580 bridges Moulton (1986). Vertical and horizontal movements greater than 102 mm (4 inches) and 51 mm (2 inches), respectively, were considered intolerable. Tolerable limits for angular distortion (differential settlement to span length) were suggested to be 1/250 and 1/200 for continuous and simple spans, respectively. It was reported that a differential settlement greater than 13 mm (0.5 inch) at the bridge interface would be sufficient to constitute a “bump” requiring mitigation."

Jan 1, 2017

By Brain E. Gombos

The Allen Park Sanitary Sewer Overflow (SSO) Tunnel and relief sewer project, located in the city of Allen Park, MI, is a long-term corrective action designed to bring Sanitary District One?s sanitary system into compliance with its 2005 consent order and service contract with the Detroit Water and Sewerage Department (DWSD). The $20 million project is intended to reduce Allen Park?s wet weather discharges to DWSD, reduce bypass pumping to the Ecorse Creek and limit the future risk of basement flooding by providing storage during wet weather events and eliminating hydraulic bottlenecks in the sanitary sewer system.

Jan 1, 2013

By G. Gomez Ciments-Calcia

The sources of complaints by neighbours of the operating quarry are due to the 3 following causes : - Impulsional noises or air hoch wawes – Vibrations - D u s t How a blasting in a quarry operation is felt by neighbours cannot be measured solely by the various limits set by national and European regulations regarding vibrations and air shock waves (sound pressure).

Jan 1, 2002

By Jose R. Hernandez-Aguilar

"This paper revisits data from previous studies (Hernandez-Aguilar, 2010, 2011) to better understand the link between metallurgical performance and pulp-zone bubble size (Db) in full-scale flotation systems. To obtain conclusive evidence exclusively related to the pulp (collection) zone, the experiments were designed in those studies to control both the bubble generation method and the influence of the froth zone on the overall metallurgical performance in industrial and pilot-scale flotation columns. The results showed that Db had a significantly larger effect on the recovery of coarse (> 75 µm) particles compared to the effect on fine (< 16 µm) particles. It was observed that, under certain practical conditions, the recovery of coarse particles was close to zero, but dramatically increased by reducing Db. The evidence revealed an inconsistency of the so-called “k–PSb” model: at constant froth recovery, increasing Sb (i.e., the rate of production of bubble surface area) did not always result in higher recovery, as the model predicts. Furthermore, the evidence showed that it was not the Sb but the bubble size that proved to be a more reliable link to metallurgical performance. Only in the presence of suboptimal-sized bubbles (Db > 2 mm) did the froth zone seem to play a role, possibly reflecting an effect of pulp-zone bubble size on froth stability. However, the role of the froth was negligible for Db < 1 mm.High-resolution mineralogical measurements performed on process samples revealed that, regardless of the degree of liberation, Db had a profound effect on the shape of the recovery-by-size curve, particularly the coarse particle size fraction. This observation is key as it implies that the loss in efficiency associated with floating the coarse particles was not the result of neither particle hydrophobicity nor particle detachment issues: even in the absence of mechanical agitation, liberated and highly hydrophobic coarse particles did not seem to attach to the bubbles in the first place, an inefficiency that was corrected by reducing bubble size. The data analysis suggests that poor attachment efficiency can practically affect both fine and coarse particles but via different mechanisms which are discussed here."

Jan 1, 2017

By Ozgul Keles, Dila Sivlin

Lithium ion batteries are potential energy source of next generation electric vehicles (EVs). However, some problems such as safety, durability, low capacity, cycle life etc. restrict their use in EVs. These problems mostly related with cathode materials, an improvement in cathode materials may cause significant changes in battery performance. In this work, to overcome cycle life problem Al2O3 coating on LiNi0.5Mn0.3Co0.2O2 cathode material produced by sol-gel method. The surface modification of LiNi0.5Mn0.3Co0,2O2 was started by adding LiNi0.5Mn0.3Co0.2O2 powders into alumina sol. Then, sonication was started and two different sonication powers were tested (45, 100%). After the second gel is obtained, last heat treatment for Al2O3 crystallization was done at 600 °C for 4 h. X-ray diffraction (XRD) measurements showed that the material had a well-ordered layered structure and Al was not in the LiNi0.5Mn0.3Co0.2O2. Al2O3 coated materials show better cycling performance compared to the pristine material. It is believed that, this improvement is caused by the fact that Al2O3 layer prevents direct contact between active material and electrolyte and reducing decomposition reactions.

Mar 1, 2018

New Zealand has often been quoted by metallurgists and others as one of the countries in which Tellurium is found, and locally it has been recorded that appreciable quantities of tellurium have been met with in the Thames and surroundingdistricts. However, specimens containing tellurium which have been obtained on this field have not been preserved and their scarcity today points to the fact that tellurium is not here abundant.To ascertain its distribution, analyses and assays have been made by the author on a large number of ores, the results of several of which are given below.The presence of any considerable percentage of tellurium has an important bearing on the metallurgical treatment of ores in which it is found.

Jan 1, 1901

By Martin Langenderfer, Catherine Johnson, Alexander Douglas

Mine haul roads degrade rapidly due to extreme loads on sub-optimal construction materials. Unmanned aerial vehicles (UAV) are suited to quantify large-area road-network conditions, such as surface roughness, defects, and grade to optimize remediation of poor conditions and reduce overall costs. Mine haul roads present unique challenges, such as material type and edge characteristics, to automatic road detection that often fail, requiring manual road input. This research proposes a new method for analysis using the road center determined by principal curve analysis of a haul truck’s Global Navigation Satellite System (GNSS) traces; analysis grids were created from this center line. A dense point cloud from UAV photogrammetry was generated, and multiple linear regression analysis was conducted on each individual grid. The root mean square error in each grid indicates the surface roughness, and the change of slope between grids indicates the road grade inconsistencies. This method was applied to 26 road sections, and the results were validated by images taken from the truck operator’s vantage point. Critical defects were identified including excessive pothole formation, corrugation, depressions retaining water, and narrowing of travel lane. The results demonstrate this is a valid method of road identification and quantification of road defects at a mine site.

Dec 19, 2023

By Márcio Zamboti Fortes

A alguns anos os setores residencial e industrial tem se deparado com mudanças de paradigmas que tangem a necessidade de melhorias em suas atividades, com o intuito de desenvolver processos com menor impacto ambiental, sustentáveis e com eficiência energética, objetivando reduzir o consumo de energia elétrica. O uso de tecnologias baseadas em fontes renováveis para a geração de energia elétrica, tais como a solar e a eólica, tem apresentado-se como uma alternativa a ser implementada por estes setores para atender às exigências do mercado, se beneficiando da difusão da tecnologia e uso destes equipamentos, para a consciente utilização da energia elétrica. A instalação e avaliação de novas fontes de geração de eletricidade estão sendo desenvolvidas pelo projeto Cidade Inteligente de Búzios através da implantação de painéis fotovoltaicos e aerogeradores de pequeno porte em unidades consumidoras residenciais, comerciais e industriais e alguns resultados estão apresentados neste texto.

Sep 25, 2017

By Wayne Anderson

Regarding the technical paper by Thomas E. Finch and Edward L. Fidler, "Recovery of Stray (Thin) Seams in Western Coal Mining." I would like to comment on this subject. In western Canada, most strip mines encounter thin seam coal or rider seams. Although the paper addresses the problems and costs associated with the recovery of this coal, it does not take into account what the savings are. Without looking at the savings, the "Total Objective" is of course not clear. I feel that in a stripping operation the mine can spend per ton (of the thin seam) up to their dragline stripping costs per ton to recover a rider seam or thin seam. The reasoning behind this is simply that this is the price the mine will have to pay to expose an equivalent amount of coal without the recovery of these thin seams. If the mine can recover a rider seam or thin seam for less than the dragline operating costs per ton, a savings will be realized. By recovering a thin seam or rider seam, the life of an ore body is extended by that amount of coal not thrown away. In addition, the cost of land acquisition, associated permits, capital, and reclamation will be reduced as more coal is delivered for a given area. When the above points are considered, the recovery of these thin seams can be very profitable and indeed worth recovering.

Jan 1, 1983

By Adilson Rodrigues da Costa

Os cilindros usados em laminadores a quente, especialmente os cilindros de trabalho são submetidos a altas taxas de desgaste da superfície durante a laminação. Após a campanha de laminação os cilindros devem ser enviados para uma retifica de cilindros para remover a camada danificada. Para este processo de retifica, são utilizadas rebolos com alta eficiência de corte e alta resistência. O objetivo foi analisar os resíduos metálicos e as partículas abrasivas do rebolo após a retificação dos cilindros e, correlacionar com o desempenho obtido com dois tipos diferentes de rebolos, sendo assim capaz de definir um rebolo com melhor desempenho e menor custo operacional.

Jul 30, 2018

By Samara Venina Simen de Azeredo Silva

Os compósitos produzidos a partir de Nitreto cúbico de Boro (cBN) são utilizados nos processos de usinagem de materiais ferrosos, tais como, peças fabricadas a partir de ligas ferrosas, ligas a base de níquel e materiais ferrosos com dureza de 45 HRc. Os compósitos a base de cBN são produzidos sinterizando cBN e seus ligantes sob condições de altas pressões e altas temperaturas (APAT). O presente trabalho tem como objetivo a caracterização microestrutural dos compósitos nanoestruturados de cBN, processados sob altas pressões e altas temperaturas, com parâmetros de pressão de 6,6 GPa e 1800oC e tempo de processamento cíclico e acíclico. Os compósitos produzidos foram testados na usinagem de aço 4140. Os resultados mostraram que uma melhor densificação e uma menor perda de massa dos compósitos durante a usinagem tem relação com os parâmetros de sinterização e com o tempo de processamento.

Aug 16, 2017

By J. A. López-Molina, S. García, V. Castellanos-Pedroza

"Groundwater inflow into underground constructions may cause hazardous working conditions and environmental problems. It is essential to localize and characterize potential flow paths and to estimate the amount of water leakages, so that appropriate sealing works can be performed. Estimating the amount of water ingress is a multi-phase process starting from qualitative and quantitative examination of rock mass. Due to association of uncertainty, vagueness and incompleteness with the monitored data set, particularly resulted from the in situ tests, accounting relevant approaches such Fuzzy Logic and Recurrent Neural Networks, are proposed in this research for learning acquisition, extraction of rules and prediction of behaviors. The computational set of artificial tools permits using the complex information entities or information granules (rock types, geologic structures, hydro-fracture potential) for data abstraction and derivation of knowledge from records (numerical or linguistic format). This is more a theoretical perspective than a set of methods or principles. As a theoretical perspective, this proposal encourages an approach to data that recognizes and exploits the information present in indexes at various levels of resolution or scales. In this sense, it encompasses the methods which provide flexibility and adaptability in the resolution at which knowledge or information is extracted and represented. The product of merging these tools is a 3D artificial-mapping of rock classification (Qi-system), geological conditions and Lugeon units that permits, as far as possible, to understand more and better the flow behavior."

Jan 1, 2015

By G. G. Morgis

In carrying out the provisions as set forth by an Act of Congress (36 Stat. 369) approved May 16, 1910, effective July 1, 1910, and the amended Act of February 25, 1913, (37 Stat. 681), the Bureau of Mines, among other activities, conducts inquiries and scientific and technologic investigations concerning mining with a view to improving health conditions and increasing safety and disseminates the general information gained by these studies. Through the medium of these publications, the causes as well as the methods that have been found most satisfactory in combating undesirable conditions are brought to the attention of the mining industry. This bulletin describes health and safety reports that have been published for the period July 1, 1955, through June 30, 1961. Technical Paper 705 issued in 1948 contains a listing of all Bureau of Mines publications dealing with health and safety in the mineral and allied industries from 1910 through 1946; Bulletin 558 contains a bibliography of such reports that were issued from January 1947 through June 1955.

Jan 1, 1962

The use of comparative sampling methods during the evaluation of the tin-copper deposits at Cleveland mine yielded closely checking average results from groove, channel, AXT split diamond drill core, and bulk sampling for both tin and copper content of the ore.The weighted mean tin and copper grades and values for the groove, channel, and split core samples showed small percentage differences from bulk sample results, and the F-ratio test for single population origin of the four types of samples was accepted at the 99&#183; 5 per cent level of confidence.These results indicate that grade estimates based on the assays from AXT split diamond drill core and/or groove samples would be reliable within practical limits.

Jan 1, 1968

By J. S. Roberts

"Campbell mines has been in operation since 1948. Part of the process consists of roasting of a flotation concentrate which contains arsenopyrite.At present operation level the milling rate averages about 850 t.p.d. and about 48 t.p.d. of concentrate is roasted. The gas emissions at present contain between 3 and 3.5 t.p.d. of arsenic trioxide, about2 - 2.5 t.p.d. of particulate matter and between 19 - 25 t.p.d. of sulphur dioxide. The particulate is extremely fine calcine dust and it assays about 4 oz. Of gold per ton.Until 1974 the gas was discharged untreated through a 125' stack.UntreatedThe decision was made in 1972 to erect a gas treatment plant, construction ran through 1973 and operation began in 1974. The cost of the installation was about 1.3 million dollars.On investigation the process technology, it was apparent that the plant operated by giant Yellowknife for the same purpose was the model we should study. I would like to acknowledge the fine cooperation we had from giant, the plant that emerged is very similar to theirs and incorporates some improvements suggested by them and based on their operating experience.The plant is designed to remove arsenic and solid dust and it has no provisions to remove sulphur dioxide.We depend upon the 125' stack to assure adequate dilution. Because of the nearby airport the stack cannot exceed 125'. A stack burner is provided that can ""y used to heat the stack gas and carry it higher into the atmosphere when there is an inversion condition.The removal of arsenic from hot gas is fairly simple. The sublimation point is about 425°f, a few degrees above this point the arsenic is a gas and a few degrees below it condenses into a solid form. The arsenic could have been removed by simply dropping the temperature below the condensation point and collecting all the solids in a baghouse. This would have removed the possibility of recovering the gold in the calcine dust and would have produced an impure and more bulky arsenic material to be placed in safe storage. The decision was made to collect the solid dust in a hot electrostatic precipitator operating above the sublimation point and subsequently lower the temperature below the condensation point and collect the arsenic in a baghouse."

Jan 1, 1976