Search Documents

By A. M. Gsudin, F. W. Bloecher, C. S. Chan-s, P. L. De Bruyn

M ANY elements can now be obtained in radioactive form. The radioisotopes have the same chemical properties as the corresponding inactive forms, differing from them only by their nuclear instability. This combination of properties permits radioelements to act as atomic tracers, the tracer atoms revealing themselves at the time of their decay with emission of electrons and positrons (beta radiation), helium nuclei (alpha radiation), or electromagnetic radiation (gamma radiation). The tracer technique is particularly attractive for the study of surface chemistry problems in general and flotation problems in particular because of its extreme sensitivity. A large proportion of the ionizing events, initiated by the characteristic decay emissions in a radioactive sample, can be recorded by radiation probes of suitable design and geometry. An idea of this sensitivity can be gathered from the following example: assume that 0.001 mg of pure RaD (radiolead), a beta-ray emitter, is used in a flota¬tion tracer experiment. This is 1210 X 10-1 mole; since the fraction trans¬formed per second (the so-called decay constant), is 9.92 X 10-10, the number of ionizing events per second would be (6.023 X 1023 X y,,, X 10-1) X 9.92 X 10-10 = 2.845 X 106. (The decay constant is expressed in sec-'. Its product with the half life, expressed in seconds, is the pure number, natural logarithm of 2 = 0.693. The half life is the length of time required for decay of one half of the total number of radioactive atoms of one particular type.) (See reference (1) at the end of this article.)

Jan 1, 1948

By B. Manoj

Coal is a mineral and is extensively used as a solid fuel in developing nationsand hasa sizeable share inthe global fossil fuel reserve. Utilization of this resource generates excess spoil and large volume of low grade waste to the environment. In recent years there have been serious research on enhancing its value and exploring the utility of this carbonaceous material to novel carbon materials.

Mar 1, 2018

By Dan Marshall, David H. Watkinson

Abstract - Cobalt, Ontario, is renowned for the 12.6 billion grams (445 million ounces) of silver produced from the area since discovery in 1903 by workers of the Timiskaming and Northern Ontario Railway. Native silver generally occurs with cobalt arsenides and sulfosalts in near-vertical carbonate veins cutting the Huronian sedimentary rocks of the Gowganda Formation, the Archean metavolcanics and/or the Nipissing diabase. All major deposits have been found within a few hundred meters of the unconformity between the Archean and Huronian rocks in general proximity to the Nipissing diabase and volcanogenic sulfide mounds within the Archean meta-volcanics. Silver has been mobilized from one or more of the local country rocks by hyper-saline brines and deposited in or near zones of mixing where the saline brines encounter paleometeoric water transported to depth along the unconformity or local structures. Previous work has shown that chloride complexes are the dominant ligands responsible for silver transport. These hypersaline brines, represented as halite-bearing fluid inclusions at room temperature, have been trapped as primary fluid inclusions within vein minerals. Pressure-temperature conditions of vein formation have been derived from mineral equilibria, maximum lithostat and fluid-inclusion studies. These data are consistent with vein formation occurring over the temperature range 300°C to 350°C, with pressures constrained between 60 Mpa and 136 Mpa (600 bars and 1360 bars).

Jan 1, 2000

Innovative and Resource-Preserving Washing Processes for Primary and Secondary Raw Materials

Sep 13, 2010

The pressure of low commodity prices forced the design process for the second lift of Northparkes E26 Mine to adopt a continuous improvement philosophy. The emphasis was to minimise capital expenditure while still maintaining the excellent low operating costs achieved on Lift 1. Although the first block cave lift at Northparkes is the most productive underground mine in the world and is held up as a benchmark for the use of technology in mining, areas for improvement were identified. Every area was critically assessed and investigated for the possible application of new techniques and technologies. Key learnings from the construction and production phases of Lift 1 were captured, documented and used as the starting point for the Lift 2 design. This paper shows how and why the design parameters initially used onLift 1 were changed to become the current E26 Lift 2 developmentproposal. The main differences between the two block caves arehighlighted. The alternative techniques and equipment that wereconsidered are also discussed. * Originally published in the Proceedings of MassMin 2000,published by The AusIMM.

Jan 1, 2001

By K. S. Lackner, T. M. Yegulalp

We present a review of research and development for coal based clean energy systems aiming for zero emissions to the atmosphere. These systems can utilize all kinds of coal or other solid carbon sources such as tar sands as well as liquid hydrocarbons. The chemical energy of carbon is transferred to hydrogen and used in power generation, in fuel cells, or hydrogen combusting turbines. The waste products of these future power-generating systems are ash, sulfur compounds and CO2. We also summarize current and developing technologies for processing of CO2to produce mineral carbonates for permanent disposal, and associated byproducts.

Jan 1, 2003

By A. E. Dabbagh

Saudi Arabia’s mineral potential offers development target that compliment the national effort to diversify the income of this oil and gas economic based nation. Ma’aden, a joint stock company with paid-up capital of US$1 billion, has from its inception in 1997, actively developed in-house engineering and management skills to transform the Arabian shield’s mineral potential into such real projects. Gold mine operating facilities of 100,000 oz/yr underground and 50,000 oz/yr open pit are de-scribed, as well as 3 targets, two of which are underdevelopment; Al Hajar (3,000 tpd at 2.5 gpt Au)and Al Amar (5,000 tpd at 20 gpt Au). Emphasis is also on exploitation of phosphate rock and down-stream fertilizer products, based on the Kingdom’s107,000 sq. km. northern basin geological reserve. Al Jalamid, the prime target, represents 216 million tonnes of these P2O5 reserves. Saudis and expatriates, together, lead international engineering companies and contractors operating and developing these facilities.

Jan 1, 2000

By Lucien Eaton

THE use of filling in mines is less common in the United States than it is in Europe, where in some places it is required by law. In most cases the filling is placed by hand, and the material used for this purpose is the waste from development and that sorted from the ore in the stopes. When these sources provide an insufficient supply, additional rock must be quarried on surface or mined underground, or some other material :st be used. In different parts of the world sand, clay, gravel, culm, nulated slag, mill tailings, and even ashes, have been used as filling material in place of or in conjunction with rock. Of all the materials used for filling the best is probably clean sand. Gravel, finely crushed rock, granulated slag and coarse mill tailings are almost as good, and the methods used for placing and confining sand will apply equally well to any of these. The advantages of sand are its comparatively slight compressibility and the ease, economy and convenience with which it may be placed. On account of the voids, which necessarily occur in fills made of coarse waste, such fills will compress 10 to 25 per cent before they develop their full strength, whereas clean sand seldom compresses more than 5 per cent. Sand is especially desirable when practically complete filling is required, and sand derived from mill tailings, especially when not thoroughly cleaned, has been remarkably effective in sealing off and extinguishing mine fires. When natural sand is available on surface, or when it can be obtained from the mill tailings or tailings dump, the cost of using this material for fill will probably be considerably less than that of rock. In this paper it is not proposed to discuss all methods of filling, butt to describe some of the methods used for placing sand fill and to make a brief comparison of their merits.

Jan 1, 1932

By R. Maxwell

"At Opemiska Copper Mines we have, over the past four years, operated 300 cu. ft. and 700 cu. ft. flotation cells as roughers, scavengers and cleaners and found them competitive with conventional flotation cells on a cu. ft. basis on all phases of flotation.The economics are very much in favour of the large cells for the following reasons:Power consumption is 35 to 40%, of conventional machinesMaintenance cost is about 20 to 25% of conventional machinesSpace required is about 30 to 35% of conventional machinesInstallect cost is about 40%, of conventional machinesTo put the above in more concrete terms below is what we are doing at Opemiska:1. Increasing mill capacity from 2000 to 3000 T.P.D. and will use only 5Cff, of the flotation space for 3000 tons that we used for 2000 T.P.D. with conventional flotation machines.2. Will require only 10 flotation cells for 3000 tons against 85 conventional cells for 2000 tons.3. Cells will be, one 2000 cu. ft. rougher, six 700 cu. ft. scavengers (2 banks of 3 each) and one cleaning circuit using three 300 cu. ft. cells.You will note that in this 3000 ton per day plant, we are going to have only ten cells. Had we put in conventional cells for this tonnage, we would have needed 120 cells."

Jan 1, 1970

By Yunnen Chen

In the present study, waste materials like pine sawdust and spent grains were investigated to assess their potential for removal of cobalt ion from water by the process of biosorption. The effects of solution pH, reaction time and initial concentration were studied in batch experiments. The removal efficiency of Co(? ) by spent grains was higher than that of pine sawdust. The initial removal was rapid and equilibrium was established in less than 90 min. Equilibrium data all agreed well with both Langmuir and Freundlich isotherm models for the two metal-biomass sorption processes. Good correlation coefficients were obtained for the pseudo second-order kinetic model. Pine sawdust and spent grains were shown to be promising biosorbents for Co(? ) removal from aqueous solutions.

Jan 1, 2010

By T. Maejima, K. Aoki, T. Mori, K. Iwano

Concerning the excavation of rock cavern, it is one of the most important issues to evaluate the behavior of rock joints. But few detailed measurements for joint behavior had been conducted. Therefore, in order to evaluate the stability of rock cavern, effective approach for monitoring and analyzing the joint behavior needs to be developed. In this paper, authors described the results of analysis for joint behavior during the excavation by comparing with both results of the in-situ measurement by BTV and the numerical analysis by MBC model. Bei Ausschachten von Gesteinshöhlen ist es von besonderer Bedeutung, das stark von den Verbindungsteilen beeinflusste Gesteinsverhalten zu bewerten. Jedoch wurden bisher nur wenige Beobachtungen über das Öffnungsverhalten von Verbindungen durchgeführt. Daher muss ein effizientes Verfahren zur Überwachung der Stabilität unterirdischer Höhlen und der Analyse des Verhaltens von Verbindungsstellen entwickelt werden. In der vorliegenden Studie beschreiben die Autoren das Verhalten von Verbindungsstellen während der Ausschachtung durch Vergleiche sowohl mit den Ergebnissen von in situ Messungen mittels BTV als auch numerische Simulation mit dem MBC Modell, welches auch Diskontinuitäten berücksichtigen kann. Quand il s’agit d’excaver une caverne dans une roche ayant des joints très développés, il importe fort d’évaluer le comportement de la roche. Cependant, le nombre d’observations du comportement des roches effectuées au niveau de joints est loin d’être suffisant. Par conséquent, pour s’assurer de la stabilité des parois des cavernes souterraines, il a fallu mettre au point une méthode fiable de détection et d’analyse du mouvement des joints. Dans cet article, les auteurs décrivent leurs études de comportement des joints pendant l'excavation, en comparant les résultats des mesures effectuées in-situ, dans un chantier d’excavation par BTV , avec ceux d’analyse de la simulation numérique par MBC permettant de tenir compte des discontinuités.

Jan 1, 2003

By E. H. Cho, Q. Luo

Pittsburgh No. 8 coal, cleaned by conventional froth flotation, was oxidized in a 2-L Parr stirred bench-top autoclave. Autoclave tests were carried out for up to 5 hrs under the following conditions: 150 to 225ºC, 60 to 500 psi 02 and 15 to 60 g of coal per 600 mL of distilled water. The oxidation of coal was evaluated by measuring the total acidic group formed on the surface of the coal and by measuring the adsorption (under standard conditions) of calcium ion from a solution. The degree of oxidation of the coal increased continuously, without much leveling off, with increasing oxygen pressure. With increasing temperature, the oxidation of the coal increased sharply between 150 to 175ºC and then leveled off above 175 °C. The adsorption of calcium was >3% on coal oxidized under the most favorable conditions. The adsorption of calcium on coal increased sharply with increasing equilibrium pH. The loss in Btu was found to be sensitive to oxidation temperature. This study concluded that the optimum oxidation of coal is achieved over 3 hrs at high oxygen pressures (e.g., 500 psi) at ~170ºC. This study also concluded that, when measured in terms of calcium adsorption, Btu loss and reaction time, the oxidation achieved in an autoclave is far superior to that achieved in a fluidized bed.

Jan 1, 1996

By N. Myung, G. Hwang, H. Kim, Y. Han, S. Choi

"According to research presently being conducted on selective lithium recovery in seawater, inorganic adsorbents with high selectivity and capacity for capturing lithium ions from liquid lithium resources are called lithium ion-sieves (LISs). Their low toxicity, low cost and high chemical stability make LISs suitable for lithium recovery from seawater. In the present study, the ultrathin LMO nanofibers with controlled diameter were successfully fabricated by an electrospinning technique with a hypothesis that greater aspect ratio (i.e., smaller diameter) would lead to the enhanced recovery of lithium ion from seawater. Design of Experiment (DOE) and dimensionless analysis were performed to systematically optimize the diameter and morphology of nanofibers. Several complementary techniques including FE-SEM and XRD were used to evaluate the physical/physicochemical properties of the nanofibers. Lastly, the lithium ion recovery was tested for the nanofibers with different physical properties using lithium ion solution. INTRODUCTION Demand for lithium resources is increasing in many industries across the world.1-2 However, the conventional resources for lithium is very limited, and it even gets worse to secure the resources due to low grade and/or complexity of feed materials. Much effort has been, therefore, devoted to obtaining lithium from aqueous lithium resources. Several methods such as solar evaporation3-4, co-precipitation5, and solvent extraction6 have been proposed for recovering lithium from an aqueous lithium source, but there are limitations on its use; It takes a very long time or conditions such as temperature, pH and Mg/Li ratio are severe. Lithium ion-sieve (LIS) materials are considered as a good lithium adsorbent because of their unique chemical structure that can selectively separate lithium ion from brine and seawater.7- 10 Furthermore, their low toxicity, low cost, and high chemical stability make LIS suitable for lithium recovery from aqueous lithium resources. Spinel hydrous manganese oxide (HMn2O4) derived from spinel lithium manganese oxide (LiMn2O4) after topotactically extracting lithium from the spinel structure by acid treatment is most widely investigated LIS.10, LIS materials have been actively studied in various forms for easy handling and high efficiency (i.e. membrane11,12, foam13-14, granular15,16). Among them, the 1-D nanostructure LIS with high specific surface area is excellent in efficiency.9 In this study, we present the part of our recently submitted work17. Specifically, we fabricated systemically lithium manganese oxide nanofibers with different diameter as a lithium ion adsorbent using electrospinning technique through design of experiment (DOE). Enhanced lithium ion adsorption properties of the HMn2O4 nanofibers with different diameter were investigated in lithium liquid resources."

Jan 1, 2018

By C. E. Beecher

The application of gas or air under pressure to obtain more oil from a sand which has been practically exhausted by ordinary production methods has been practiced to a limited extent for many years. Until recently such methods were confined to the Eastern fields, principally those of Ohio and West Virginia, where in many cases the production obtained after applying pressure for a few years was nearly equal to the total production prior to that time which had been obtained by the usual production methods. As early as 1917, J. 0. LewisL called attention to this method of increasing the recovery of oil and cited the phenomenal results obtained by H. E. Smith, I. L. Dunn and 0. C. Dunn, who pioneered the application of air or gas pressure recovery methods. With this information available it would appear that other oil-producing sections of the country have been extremely slow to realize the advantages of repressuring. However, after a few successful projects in the Mid-Continent area, the oil producers appreciated t' e value of this method for obtaining further and profitable production from their practically exhausted leases and are now making extensive use of it. In general, it has been the practice to apply pressure to the sands when production has declined to a small yield per well. The purpose of this paper is to discuss some of the advantages which may be expected from returning gas under pressure to the oil sands during the early stages of development, before the rock pressure has been dissipated and the gas exhausted, and to stimulate discussion of this subject on which comparatively little actual field data are available. The Function of Gas Gas associated with or dissolved in the oil is the source of energy causing movement of the oil to the well. When this energy is dissipated production ceases. The exception to this general statement is found in fields where hydrostatic water pressure may supply energy after the gas

Jan 1, 1929

By Andreas Prucker

The Greater Vancouver Water District (GVWD) is currently constructing the largest water treatment plant in Canada. As part of this treatment scheme twin water transfer tunnels are being constructed. Work commenced with the 11 m diameter, 185 m deep Seymour Shaft which was excavated by drill and blast using a mobile crane for hoisting. The Seymour Shaft is the first large diameter shaft that has been sunk in Western Canada in recent years. The operational aspects associated with the hoisting, the drill-blast-support cycle and water control in the shaft are the focus of this paper.

Jan 1, 2008

By J. P. Walker

"INTRODUCTION Sponge iron has been made commercially since 1912 at a Swedish ceramic plant; and the product, known as Swedish disk-type nagger sponge iron, has an excellent reputation as a superior furnace feed wherever high-grade steels are made.The general procedure for making brickyard sponge iron was described frequent in Swedish technical journals before 1932 and at that time consisted in filling clay refractory containers, called saggers, with iron ore plus the necessary quantity of solid reducing agent and then firing in an ordinary ceramic kiln. Two types of sponge iron were made in this way: (1) An inferior, high-sulfur product obtained by mixing the ore and solid reducing agent; and (2) a high-grade, low-sulfur product made by filling the sagger with alternete layers of unmixed ore and reducer, yielding sintered disks of metallic iron particles.Swedish disk-type sponge iron of interest to the steel industry because it has a very low sulfur content, even when made by the use of low-grade, high-sulfur coals for reducing and firing. The Swedish product also contains little siliceous gangue residue and is almost phos¬phorus-free. To those features must be added the high metallic-iron content -90 to 96 percent - and freedom from even small amounts of the metals that are undesirable in steel making.The details essential for successful operation of this procedure are not known, especially as regards improvements said to have been made since 19;2. The Bureau of Mines therefore decided to determine some of these missing details, and this report records the results of the first set of experiments on the manufacture of brickyard or sagger sponge iron."

Sep 1, 1945

By Toshiyuki Kozuka

CdTe metal composite semi-conducting material has high potential in good performance of energy conversion efficiency for solar cell and there is much room for improvement of the performance by developing a process of making a thin CdTe film. In this paper, the imposition of intense magnetic field on CdTe electro-depositing surface is proposed, which is one of the possibilities for improving the energy conversion efficiency. In the experiment, cryogen-free super-conducting magnet up to 5T was used and CdTe film was deposited electrically in -o.nv vs. SHE The electrolyte was Cd and Te ammonia alkali solution with controlled temperature in the acrylic cell of 70mm diameter. Electro-deposition behavior of CdTe has affected by the imposition of the intense magnetic field due to microscopic convection in the vicinity of the depositing surface. Electro-deposited surface of CdTe becomes smooth due to microscopic convection around the surface, and the crystallization behavior is also affected, where crystallization temperature and the grain size is changed by the imposition of intense magnetic field.

Jan 1, 2003

By Steven W. Hunt

Appropriate seals, portal ground improvement, and compatible shaft construction techniques are vital elements for launching and receiving tunnels effectively in urban areas where adjacent property requires protection from excess ground movements. This paper focuses on seals and ground improvement along with shaft wall types, required to launch or receive tunnel boring machines within wet, permeable ground at the portal zone. The paper also discusses probing to verify suitability before the tunnel eye is cut. Methods addressed include: rubber gasket seals; soft eyes; double walls; top hats for reception; and, portal zone ground improvement (permeation grouting, jet grouting, un-reinforced slurry diaphragm wall panels, ground freezing, deep soil mixing, dewatering, and over-excavation and backfilling). This paper focuses on challenges with launch and reception of pressurized-face TBMs with precast concrete segment linings. Challenges related to pipe jacking are discussed in a separate paper titled ?Mitigating Microtunnel Launch and Reception Challenges? (Hunt and Finney 2008).

Jan 1, 2008

By M. G. Fleming

The professional mineral engineer is an individual of personal integrity who has undergone rigorous intellectual instruction in the scientific disciplines fundamental to his vocation; he has learnt to apply these disciplines to the discovery, mining and treatment of mineral resources and, through practical training and experience, has acquired competence and judgment to fulfil his undertakings. In the course of this development he has recognised and accepted a threefold responsibility to society, to his employer and to his profession

Dec 1, 1971

By L. Wolofsky

"The Candego property is in Boisbuisson and Christie Townships, Quebec, about 13 miles south of Marsoui, a village on the north coast of the Gaspe peninsula, 80 miles east of the railhead at Matane. It was the first producing mine in the peninsula. Production to October 1954, when operations were suspended, totalled 68,497 tons of ore, which yielded concentrates containing 8,706,535 lb. lead, 5,870,272 lb. zinc, 355,526 oz. silver, and about 1,000 oz. gold. The property was acquired by the present company in the summer of 1955.The mine has been developed by seven adits, driven into the west slope of the valley of the Marsoui River. The river here is at an elevation of about 1,600 feet, and is roughly 1,500 feet below the level of the adjacent upland. Adit elevations range from 1,760 to 2,330 feet. Five of them are in one vertical zone, on what was originally believed to be a single vein. Past production has come from Nos. l to 5; the chief present high-grade ore reserves are in No. 7.The author's observations were made in adits Nos. 3 to 6, in several of the old pits, in the surface trenches, and on drill core, at various times between December 1952 and September 1953. Much of the surrounding area has been mapped by Jones (I) and McGerrigle (2) for the Quebec Department of Mines. H. M. Kingsbury served as consulting geologist to the mining company for several years.General GeologyThe Candego veins occur in Lower ( ?) Ordovician sedimentary rocks which form a strip about 15 miles wide along the north coast of the Gaspé peninsula. The series includes limestones, shales, and sandstones, mildly metamorphosed in places. Three miles south of the mine is the north contact of the granitic intrusive, regarded as Lower or Middle Devonian, which underlies the Tabletop Mountains area. This batholith is about 10 miles long, in a north-south direction, and about 4 miles wide. At Mount Albert, about 5 miles west of the Tabletop intrusion, is a group of basic rocks, amphibolites and serpentinized peridotites, thought to have been intruded at the close of the Ordovician."

Jan 1, 1949