Search Documents

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Also included are tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1988

By W. Smith

The U.S. Bureau of Mines (USBM) is using laboratory and computer-based techniques to investigate the post- failure behavior of yielding pillars and pillar reinforcement techniques to control entry deformation. Poorly dimensioned yield pillars, can cause adverse ground conditions. Laboratory studies to evaluate various reinforcement techniques for controlling yield pillar deformation were conducted. A cracking and crushing model is used to evaluate potential tensile and compressive failure planes within pillars of various widths to assess the degree of yielding and stress redistribution. The use of an elasto-plastic model to evaluate the effect of various reinforcement on yield pillars is also discussed. These procedures effectively account for the residual pillar strength, important in yield pillar design.

Jan 1, 1995

The æMountain Camp reefÆ at Alford's mine, Wakamarina,Marlborough, had no recorded gold production although assays of 5 - 26 g/t were reported, but it did produce c. l000 kg of scheelite. The lode consists of a lower massive quartz layer, and upper, cm-banded, ribboned quartz layers, and has a very low sulphide content. Within the massive layer, relict early fine-grained mosaic quartz with idioblastic scheelite is surrounded by recrystallised granoblastic coarse-grained quartz with calcite and plagioclase, in which an original ribbon banding texture is mimiced by strings of tiny inclusions. In both the banded and massive layers, rounded quartz grains, created by cataclastic milling of grain margins and along syn-vein fractures, have been partially annealed within later quartz overgrowths. Late fibrous quartz and calcite fill brittle cross fractures.   Deformation events D1 and D2 are associated with mid-late Jurassic metamorphism of the Pelorus Group, D2 producing the main regional schistosity (S2, and the earliest scheelite. D3 is an extensional mylonitic shear event that formed the dominant schistosity in Alford's mine (S3). The quartz lode was emplaced within the mylonite by a series of individual dilation pulses (D4). The D5 event caused crenulation of the S3 mylonite, kink banding and chevron folding of the S2 schist and S3 mylonite, and reverse faulting, rodding and cross-fracturing with late fibrous quartz-calcite veining of the D4 quartz lode.   Fluid influxes during successive dilations of D4 fractures progressively caused recrystallisation of earlier quartz bands on the footwall, annealing and recrystallisation of quartz along milled crystal margins and fractures, and deposition of minor sulphides. There was thus a dynamic interplay between fault dilation, lode fracture, fluid influx, lode band deposition, and lode recrystallisation. Illite-Kfeldspar al ¦ 2 Ma (K/Ar), c.30 Ma after metamorphism.

Jan 1, 1996

By M. J. Gregory

The Pebble Cu-Au-Mo deposit in southwest Alaska is one of the world's largest porphyry deposits. The western part of the deposit was discovered by Cominco America in 1987, who sold the project to Northern Dynasty Minerals Ltd., in 2001. Northern Dynasty discovered the high-grade eastern part of the deposit in 2004 and went into a 50:50 partnership with Anglo American PLC in 2007, forming the Pebble Limited Partnership (Lang et al., 2008). The Pebble Limited Partnership has continued to delineate the deposit through diamond drilling with the most recent resource estimate released in February 2010 (Pebble Limited Partnership, 2010). The Pebble deposit mineral resources comprise 5.94 billion tonnes of measured and indicated resources grading 0.78% Cu EQ, containing 55 billion pounds of copper, 67 million ounces of gold and 3.3 billion pounds of molybdenum. Also delineated are 4.84 billion tonnes of inferred mineral resources grading 0.53% Cu EQ, containing 25.6 billion pounds of copper, 40.4 million ounces of gold and 2.3 billion pounds of molybdenum (Pebble Limited Partnership, 2010). Resources are calculated using a 0.3% Cu EQ cutoff. GEOLOGY AND MINERALIZATION Deposit Geology The Pebble deposit is located in the Kahiltna terrane, between terminal strands of the north-east-striking Lake Clarke strike-slip fault. This fault represents an accretionary boundary and separates the Kahiltna terrane to the north-west from the Peninsular terrane to the south-east (Lang et al., 2008). The Pebble deposit represents a large magmatic-hydrothermal system centered on a group of 90 million year old porphyritic hornblende granodiorite intrusions. An east-west cross section through the southern part of the deposit (Figure 1A) shows the typical relationships between the various rock units which host sulfide mineralization. Sub-parallel ~96 million year old granodiorite and diorite sills were intruded into siltstones of the Jura-Cretaceous Kahiltna flysch. In the west, these sills were cut by a ~96 million year old alkalic intrusive complex composed of porphyritic monzonites and monzodiorites and related intrusion breccias (Bouley et al, 1995). The mineralized 90 million year old hornblende granodiorite intrusions cut all rock types and comprise four small stocks in the western part of the deposit and a larger pluton in the eastern part of the deposit. Recent deep drilling indicates that these intrusions coalesce at depth. The strongest porphyry-style mineralization is centered on the eastern granodiorite pluton and extends into the surrounding rock units (Figure 1A). The western half of the deposit crops out at surface, whereas the eastern side is un-conformably overlain by a cover sequence of Late Cretaceous to Eocene sedimentary and volcanic strata. The deposit was tilted 20º to the east during the Eocene.

Jan 1, 2012

By Ken Santini, Ronald R. Bauer, Joseph R. Copeland

Wollastonite, named after W.H. Wollaston, an English chemist and mineralogist, is a calcium metasilicate having the chemical formula CaSiO2. Although it is a unique mineral, wollastonite has a short history of industrial use. Wollastonite is the only naturally occurring, nonmetallic, white acicular mineral. Its acicularity is the main reason for its ascendancy in the late 1970s and 1980s as a reinforcing filler and as a replacement for short-fiber asbestos and short-fiber milled fiberglass. Wollastonite is used in applications ranging from bowling balls to automobile fenders, from ceramic tile to automobile brakes, and from thermal insulation board to protective industrial coatings. The United States is the largest producer of wollastonite, with China, India, and Finland as the other three major sources. The United States, Europe, and the Far East are where most of the production is consumed. Geology Mineralogy and Physical and Chemical Properties Wollastonite, a member of the pyroxenoid mineral group, has the theoretical composition of 48.3% CaO and 51.7% SiO2. Iron, manganese, magnesium, or strontium may substitute for some of the calcium. Commonly associated minerals include garnet, diopside, calcite, quartz, epidote, apatite, and sphene. Some of the physical properties of wollastonite are listed in [Table 1]. Wollastonite is largely chemically inert; however, it can be decomposed in concentrated hydrochloric acid. Some wollastonite will fluoresce under shortwave or longwave ultraviolet light, or both, with colors ranging from pink-orange to yellow-orange and, more rarely, bluish green. In addition, wollastonite may show phos¬phorescence. Because of its unique cleavage properties wollastonite breaks down during crushing and grinding into lath-like or needle-shaped particles of varying acicularity. This particle morphology imparts high strength and is therefore of considerable importance in many of the markets for wollastonite. The acicularity of particles is defined by their length:width, or length:diameter, ratio (i.e., aspect ratio). Individual particles, even the smallest ones, commonly ex¬hibit an aspect ratio of 7:1 or 8:1 and have an average diameter of 3.5 gm. Low aspect ratio products (powder wollastonite, or milled grades) with 3:1 to 5:1 aspect ratios are used as general fillers, in ceramics, and in metallurgical fluxing. High aspect ratio products with ratios of 15:1 to 20:1 are used as functional fillers for rein¬forcing thermoplastic and thermoset polymer compounds and as a replacement for asbestos. The dry brightness and whiteness of wollastonite are also important in determining its suitability for certain filler and ceramic applications. When pure, the mineral is brilliantly white, but impurities may color it cream or gray. Brightness is determined by measuring the reflectance of finely ground powder against a stan¬dard that is assigned a brightness of 100. Magnesium oxide and barium sulfate are the two standards used. G.E. brightness, a term used in North America, refers to brightness measured with a Gen¬eral Electric reflectometer. Commercial wollastonite products usu¬ally have a G.E. brightness ranging from 85 to 95. The Hunter method is also used to measure the brightness of wollastonite. Loss on ignition (LOI), another important property in determining applications for wollastonite, is the amount of volatile matter driven off when the mineral is heated to 1 000°C. Com¬mercial wollastonite products have an ignition loss ranging from 0.5 to 2.0%. Wollastonite's naturally high pH of 9.9 (10% water slurry) is of major importance to its use in the coatings industry. Coatings formulators use milled grades as a pH stabilizer in interior and exterior PVA (polyvinyl acetate) and acrylic latex paints. There are two polymorphs of calcium silicate: wollastonite, a low-temperature form, and pseudowollastonite, a high-temperature form. Conversion of wollastonite to pseudowollastonite occurs at about 1 120°C and results in an increase in the coefficient of expansion and a color change. Pure white wollastonite may change to a cream tint or to various shades of red or brown. This color change is thought to be due to the presence of iron and/or strontium.

Jan 1, 1994

By Bernard Kopelman

The particle size of tungsten metal powder used to make tungsten wire for use in radio tubes and incandescent lamps must be closely controlled if the highly desirable feature of nonsagging is to be achieved. Our knowledge of factors affecting the particle size of tungsten powder has been limited by lack of any extensive literature on the subject. There are no publications in the English language discussing this problem in any but the most general terms. In this paper the published experimental information on this subject is reviewed. Based on the published data and some experimental data obtained by the author, a general theory of factors affecting the particle size of tungsten metal powder obtained by reduction of the oxides in hydrogen is offered. The various forms of the tungsten oxides and tungsten metal used in the experiments described were those prepared by commercial processes, so that the experimental results obtained on a laboratory scale would be more directly applicable to actual commercial reduction conditions. The effects of time of reduction, temperature. and concentration of water vapor in the hydrogen were observed by counting microscopically the particle distribution obtained. Such a method is very time-consuming, but the data obtained by this method are more reliable and more fundamental than those obtained by any of the several instruments available for measurement of particle size. Review of the Literature Until the year 1912, tungsten powder was prepared commercially by reducing tungstic oxide in the presence of carbon or one of its compounds (such as glycerin or ethylene glycol), usually by firing the mixture in a closed fire-clay crucible. The resultant powder contained about 95 per cent tungsten.' When reduction of tungsten oxides by H² was introduced Commercially,²,³ several investigators became concerned with the equilibria between tungsten metal and its several oxides in an atmosphere of hydrogen and water vapor.4-l3 While these many investigations were in fair agreement on the equilibria WO³ + H2 = WO2 + H2O and WO2 + 2H2 = W + 2H2O there arose considerable controversy as to the chemical composition of the oxide between WO³ and WO², because of very poor agreement on the equilibrium constant of this intermediate oxide reduction reaction. The controversy on this intermediate oxide has been in progress for more than 100 years. Thus Malguti,14 in 1835, decided it was WO2.56 In 1857, Riche15 proposed the formula W³O8. Usler,16 in 1865, confirmed the existence of WsO8 and further proposed W1O1l. In 1897, Desil7 agreed upon W²O8 but also found W5O14.

Jan 1, 1947

By Bernard Kopelman

The particle size of tungsten metal powder used to make tungsten wire for use in radio tubes and incandescent lamps must be closely controlled if the highly desirable feature of nonsagging is to be achieved. Our knowledge of factors affecting the particle size of tungsten powder has been limited by lack of any extensive literature on the subject. There are no publications in the English language discussing this problem in any but the most general terms. In this paper the published experimental information on this subject is reviewed. Based on the published data and some experimental data obtained by the author, a general theory of factors affecting the particle size of tungsten metal powder obtained by reduction of the oxides in hydrogen is offered. The various forms of the tungsten oxides and tungsten metal used in the experiments described were those prepared by commercial processes, so that the experimental results obtained on a laboratory scale would be more directly applicable to actual commercial reduction conditions. The effects of time of reduction, temperature. and concentration of water vapor in the hydrogen were observed by counting microscopically the particle distribution obtained. Such a method is very time-consuming, but the data obtained by this method are more reliable and more fundamental than those obtained by any of the several instruments available for measurement of particle size. Review of the Literature Until the year 1912, tungsten powder was prepared commercially by reducing tungstic oxide in the presence of carbon or one of its compounds (such as glycerin or ethylene glycol), usually by firing the mixture in a closed fire-clay crucible. The resultant powder contained about 95 per cent tungsten.' When reduction of tungsten oxides by H² was introduced Commercially,²,³ several investigators became concerned with the equilibria between tungsten metal and its several oxides in an atmosphere of hydrogen and water vapor.4-l3 While these many investigations were in fair agreement on the equilibria WO³ + H2 = WO2 + H2O and WO2 + 2H2 = W + 2H2O there arose considerable controversy as to the chemical composition of the oxide between WO³ and WO², because of very poor agreement on the equilibrium constant of this intermediate oxide reduction reaction. The controversy on this intermediate oxide has been in progress for more than 100 years. Thus Malguti,14 in 1835, decided it was WO2.56 In 1857, Riche15 proposed the formula W³O8. Usler,16 in 1865, confirmed the existence of WsO8 and further proposed W1O1l. In 1897, Desil7 agreed upon W²O8 but also found W5O14.

Jan 1, 1947

By Thomas Donnelly

Introduction THE Province of San Cristobal is situated on the south side of the island of Santo Domingo about 25 miles west of Santo Domingo city, the capital of the republic. The copper mineralization is found about 1.-CAMP BUCARO. THE TOP OF THE RIDGE IN THE BACKGROUND MARKS THE CONTACT OF THE LIMESTONE AND TUFFS. S miles north of the town of San Cristobal, in the section known as Bucaro Hill; in San Francisco Hill; on the Nigua River; and on the Jaina (Liver. The district is reached by automobile from Santo Domingo city over an excellent road for 25 miles to San Cristobal, and then, by horse-back 6 or 8 miles up the Nigua River to what is locally known as "Camp

Jan 8, 1915

By J. R. Long, A. H. Roberson, T. R. Graham, R. S. Dean

EXPERIMENTAL work on the properties of high-purity alloys of the copper-manganese-zinc system has necessarily required extensive metallographic work to determine the equilibrium conditions in this system. Previous work on these alloys is fragmentary and, unfortunately, based on alloys made with impure grades of manganese, thus introducing significant amounts of iron, silicon, aluminum and carbon. Since these elements are known to affect equilibrium conditions, it became desirable to re-examine these alloys made from the pure metals. The alpha solid solution field was of particular interest and, therefore, was chosen for the initial work, which was outlined to determine the composition limits of this field. PREVIOUS WORK Heusler1 conducted an extensive survey of the liquid-solid regions of this system and also made an estimate of the solid-phase boundaries at 340°C. The pertinent part of his diagram is given in Fig. I, but it is of limited usefulness, since it applied to a single temperature only and is based on impure alloys under admittedly nonequilibrium conditions. Bauer and Hansen,2 likewise working with impure alloys, have determined the phase boundaries for alphabeta brasses containing small amounts of manganese and indicate an increase in the extent of the alpha field with increasing manganese. This is not in accordance with Heusler or with data obtained on pure alloys.3 They also described a third constituent precipitating in the alpha plus beta field below 350° to 400°C. but did not identify this constituent. Guillet4 and Heike and Ledibur5 have also noted this precipitate Each of these investigators recognized that impurities present in the manganese could and did have an effect on the structure and properties of their alloys. Corson6 in particular pointed out the hardening effects of silicon, aluminum, and carbon in copper-manganese alloys and Heusler reported that his alloys containing more than 25 per cent manganese were extremely brittle. In all probability this brittleness was due to the impurities present. This early work, therefore, should be taken as a general guide for preliminary studies only, and high-purity alloys may be expected to produce different results. The work of the Bureau of Mines laboratories with electrolytic manganese has been briefly summarized by Dean7 but includes only a short section on this system. Later work3 outlined a limited portion of the alpha field in the neighborhood of 65 per cent copper, 10 per cent manganese, and 25 per cent zinc. The present work was under-

Jan 1, 1945

By Duane L. Abata

Toxic gases produced by the detonation of six explosives were measured in an underground hardrock metal mine during actual mining operations. The six explosives included two semi-gelatin dynamites, three slurry explosives and an ammonium-nitrate, fuel-oil/ammonia dynamite combination. Explosives were detonated at the face of a drift and the toxic gases produced by the detonation were trapped to the end of the drift by a bulkhead located a short distance away from the face. Toxic gas concentrations were then measured with direct readout instruments and together with the containment volume, the toxic gas volumes per mass of explosive were calculated. Toxic gas measurements were found in the following ranges (ft3/lbm): N02 0.010-0.035; N02, 0.003-0.019; CO, 0.08-0.30; S02, 0.00-0.05; and C02, 0.7-1.8. Results showed that toxic gas production (ft3/lbm) correlated with the densities (kg/m3) and energy densities (kJ/kg) of the explosives tested.

Jan 1, 1978

By Enrique Fernández

INTRODUCTION The high speed rail link between Madrid and Asturias, in the North of Spain, has encountered in the Cantabrian range the biggest challenge of the whole line, a very deep tunnel, 25 km long through a foreseen difficult geology. This tunnel was divided in the following four lots for construction: ¦Lot 1: Pola de Gordón- Folledo. L=10,7 km ¦Lot 2: Folledo-Viadangos. L=4,166 m ¦Lot 3: Viadangos- Los Pontones. East tube. L=10,4 km ¦Lot 4: Viadangos- Los Pontones. West tube. L=10,4 km. Dragados S.A. leading a JV was contracted to design and built the Lot 2 on the captioned Pajares High Speed Railway Tunnel. The Lot 2, comprising the middle third section of the 25 km long tunnel has an additional challenge: the construction of one access from the surface to allow it own construction. Feasibility reports and preliminary design do not foresee the use of TBM due to the risk of squeezing ground at the deepest area of the tunnel. On the other hand, conventional NATM excavation of the twin tunnels and ancillary works, including access shafts were against the expected construction schedule by the client, due to the poor ground foresee at the early stage.

By M. C. Williams

The solution of the dynamic population balance model (PBM) of a closed grinding network consisting of a mill, sump, and cyclone is problematic. The fact that the dynamic PBM model equation solution to the Inverse Problem for grinding systems is degenerate or underspecified is demonstrated. Two numerical solution approaches to the Inverse Problem are used. These are: 1) providing additional constraints on breakage selection functions or 2) performing the Arbiter-Bhrany (or other) normalization of the selection functions. Actual experimental anthracite batch grinding data is used to demonstrate the non-unique functionality of the batch dynamic mill selection and breakage functions for a real physical system. The Levenberg-Marquardt algorithm for systems of constrained non-linear equations is used to solve the batch dynamic PBM grinding equations to obtain the grinding selection and breakage rate functions. Different solutions to the same PBM transport equations are provided. The mill, sump and hydrocyclone were modeled as a CSTR operating at various retention times. Batch dynamic PBM data was used to provide the mill kinetic and breakage selection function data. Two different solutions were obtained depending on the numerical solution approach. The severity of the non-uniqueness problem for dynamic grinding is demonstrated. Each solution approach to a dynamic PBM with transport, while giving the same prediction for a single batch grinding time, gives different solutions or predictions for mill composition for other grinding times. This fact makes dynamic nodal analysis and control problematic. The fact that the constraint solution approach gives a solution may suggest that normalization for closed networks is not necessary. Differences in solutions to the PBM cannot be excused away by inaccuracies in the data used to model the grinding phenomenon.

Jan 1, 1995

By M. John Brodie

This report reviews the regulatory environment as it pertains to waste rock management and disposal from mining operations, excluding coal and placer gold operations, in the \irate of Alaska. It is based on the EPA's staff position on an effective program to regulate mining waste as presented in the May, 1990 Strawman II document. The unique conditions which occur in pans of the state, including a fragile environment, high seismicity and permafrost, are identified. The special waste management practices which are necessitated by these conditions are delineated. The report provides a detailed outline of the current technologies that are suitable for designing, constructing, operating and closing a waste rock facility to meet environmental protection objectives. Cost implications to the mining industry of potential regulatory actions, such as the degree of groundwater protection, are examined.

Jan 1, 1992

By Wesley Schmutzler

The Deep Mixing Method (DMM) was employed to raise and support the LPV (Lake Pontchartrain and Vicinity) -111 Levee in New Orleans. Even using innovative technologies, the tight schedule to achieve the 100 year elevation by June 1, 2011 was a daunting endeavor. The size and scope of DMM proposed for LPV-111 was on a scale never attempted outside of Japan. Over 1.65 million cubic yards of DMM was installed. LPV-111 is adjacent to the Bayou Sauvage Wildlife Refuge, which is the largest urban National Wildlife refuge in the United States. By utilizing DMM to control settlement and improve stability of the taller levee, side slopes were steepened from the conventional 1V:4H to 1V:2.85H, thus avoiding encroachment into the Bayou Sauvage and reducing the amount of clay needed for the completed levee. The COE utilized Early Contractor Involvement (ECI) for this contract. The ECI process allowed for input from the DMM contractor, TREVIICOS South, in order to optimize equipment resources and material requirements. This paper gives an overview of the extensive DMM requirements for LPV-111 and explains the benefits of the ECI process.

By W. M. Armstrong, John A. H Lund

The paper describes an investigation of some of the tensile properties of single crystal vanadium, poly-crystalline vanadium and polycrystal-line tantalum, in the range of: W°C to -196°C. Techniques employed in the preparation and testing of specimens are discussed in detail. Some results of determinations of the temperature dependence of yield stress and ductility are given, and discussed in terms of the Cottrell-Bilby Theory of yielding. At subnormal temperatures, all the body-centred cubic transition metals in the Periodic Table exhibit; a) the "yield phenomenon" in tension, b) a strong temperature and strain rate dependence of yield stress, and c) a large decrease or complete loss of ductility. The yield phenomenon (existence of an upper and lower yield point) has been explained by Cottrell and Bilby ( 1) in terms of the dislocation-locking effect

Jan 1, 1961

By D. S. Kieffer

Ground characterized by hard boulders embedded in soft matrix represents one of the most challenging conditions for TBMs, as the cutterhead must cope with the non-optimal conditions of cutting hard blocks while simultaneously excavating through soft, soil-like matrix material. Dowden and Robinson (2001) and Hunt and Mazhar (2004) summarize several case histories relating to the problems of advancing a TBM through boulder-laden ground and provide guidance with respect to appropriate site investigations and baselining strategies. Some rock types constituting boulder-laden ground include: ?Sedimentary Rocks?cemented alluvial channel deposits, colluvium/talus, landslide debris, and glacial till. ?Igneous Rocks?agglomerates, lahars, and pyroclastic deposits. ?Metamorphic Rocks?tectonic mélange and cataclastic fault zones. ?Decomposed Rocks?corestone bearing saprolites. Disc cutters are commonly utilized to cut the hardblocks; however, as compared to the understanding of disc cutter behavior in hard continuous rocks, little is known regarding fundamental cutting mechanisms in highly heterogeneous bouldery ground conditions. To advance this understanding, a suite of full scale tests have been performed using a linear cutting machine at the Colorado School of Mines (CSM). This paper summarizes the observed cutting mechanisms and their practical implications for TBM excavations through boulder-laden ground.

Jan 1, 2008

By Daniel Journeaux

Introduction Daniel Journeaux is President of Janod Incorporated. Janod is a family owned and operated company that has been working in the field of slope stabilization since 1970. Daniel has worked in the rock stabilization industry for 25 years and has been President of Janod since 1992. Daniel has been an invited speaker for the Federal Highways Administration for the Northwest and Southwest divisions, Queens University in Kingston Ontario, The University of Laval, Vulcan Materials Company, CSX annual meeting for the Northeast Division. Daniel has written several articles and has been published in Pit and Quarry, World Tunneling, and American Shotcrete Association magazines. What is Required to Remediate Highwalls There are several techniques available to stabilize highwalls or temporary rock walls to allow for safe mining practices. The following are some of the techniques that can economically be used.

Jan 1, 2005

By Artur R. P. Junior Sergio, Pedro A. Netto, N. Monteiro, Foluke S. de Assis, Frederico M. Margem

Synthetic fibers are being replaced gradually by natural materials such as lignocellulosic fibers. Compared to synthetic fibers, natural fibers have shown advantages in technical aspects such as environmental and economic. So there is a growing international interest in the use of those fibers. The banana fiber presents significant properties to be studied, but until now few thermal properties on banana fiber as reinforcement of polyester matrix were performed. The present work had as its objective to investigate, by photoacoustic spectroscopy and photothermal techniques the thermal properties of diffusivity, specific heat capacity and conductivity for polyester composites reinforced with banana fibers. In the polyester matrix will be added up to 30% in volume of continuous and aligned banana fibers. These values show that the incorporation of banana fibers in the polyester matrix changes its thermal properties.

Jan 1, 2015

By John R. Rhodes

The objective of this project was to investigate the feasibility of analytical techniques potentially capable of determination of Mg, Al, Si, S, Ca and Fe in 1 to 2 mg samples of respirable coal mine dust, in a total analysis time of not more than 10 minutes per sample, using equipment capable of being truck mounted for field-laboratory operation. It was not essential that the technique be non-destructive, but the chosen technique is, and this enables the analysis to be performed directly on the 37 mm diameter membrane filter on which the respirable dust sample is normally collected. The sensitivity requirements are therefore quoted in terms of the units of measurement, µg/cm2. The detection limit (3o of the background criterion) should be 0.5 µg/cm2 or less. The precision should be 5% or better, at concentrations above which the detection limit is not the determining factor.

Jan 1, 1972

By HAROLD VINTON COES

MANAGEMENT has been tersely defined as getting things done through the efforts of other people; but before we proceed further, let us distinguish between administration, management, and organization. Oliver Sheldon in his book, "The Philosophy of Management," offers the following definitions: Administration is the function in industry concerned in the determination of the corporate policy, the co-ordination of finance, production, and distribution, the settlement of the compass of the organization, and the ultimate control of the executive.

Jan 1, 1943