Search Documents

By A. S. Yue

The movphology of the Mg-32 wt pct Al eutectic has been studied as a function of freezing- rate and temperature gradient. At slow freezing rates a lamellar eutectic was formed; whereas, a rod-like eutectic was generated at fast rates. The inter-lamellar spacing increased as the freezing rate decreased in aggreement with theoretical predictions. Lamellar faults, morphologically similar to edge dislocation models in crystals, were responsible for the subgrain structures in the eutectic mixture. A linear increase in fault density with freezing rate was observed. Fault concentl-ations of the order of 10 per sq cm for a range of freezing rates from 0.6 to -3.0 x 10 cm per sec were estimated. The transformation from lamella?, to rod-like morphologies was determined experimentally to be dependent on the freezing rate and independent of the temperature gradient. Moreover, the number of rods formed per- unit cross-sectional area increased exponentiallv with increasing freezing rote. BRADY' and portevin2 classified eutectic structures into lamellar, rod-like, and globular according to the morphology of the solid phases present. Although this classification is quite descriptive, very little has been reported on the details of the mechanism by which the eutectic structures are formed. Recent work by Winegard, Majka, Thall, and chalmers3 and by chalmers4 on lamellar eutectic solidification suggest that the maximum thickness of the lamellae decreases with increasing rate of solidification due to inadequate time for lateral diffusion. scheilS and Tiller' have shown theoretically that the lamellar widths indeed depend on the solidification rate. However, there has been no experimental evidence to support the theory. Chilten and winegard7 have studied the interface morphology of a eutectic alloy of zone-refined lead and tin. They found that the lamellar width decreased as the freezing rate increased in agreement with the theoretical predictions of scheils and Tiller.' More recently, Kraft and Albright' have investigated the microstructures of the A1-CuA12 eutectic as a function of growth variables. They observed lamellar faults present in the lamellar eutectic, similar to edge dislocation models in crystals. Furthermore, Kraft and Albright reported that they could not designate which extra lamellar was responsible for the formation of a lamellar fault even under electron microscopic magnification. In this paper, the morphology of the Mg-A1 eutectic structure is described. The effects of freez- ing rate on the interlamellar spacing and on the lamellar fault density are presented in detail. The transformation from lamellar to rod-like eutectics is discussed in terms of the freezing rate and the temperature gradient. EXPERIMENTAL PROCEDURE The experimental details of alloy preparation, the decanting mechanism and the determinations of the freezing rate and the temperature gradient have been reported elsewhere. Measurements of plate-edge angles were made with a microscope. The true angles used to determine the interlamellar spacings were determined by a two surface analysis technique.'' Since the decanted interface structure does not represent the true eutectic morphology on the solid,g all measurements were made from an area in the solidified bar behind the interface. Measurements of the apparent interlamellar spacings between the two phases of the eutectic were made on a photographic negative by means of a calibrated magnifier. Each value listed in Table I represents the average of thirty measurements on one negative. In general, these measurements are approximately equal with an error of less than pct. The average rod diameter for each specimen was also measured on a magnified photomicrograph. Each value of the diameter represents the average of fifty measurements. RESULTS AND DISCUSSION The experimental observations and their discussion to be presented here are restricted to the morphology of the eutectic structure and to the effects of the freezing rate and the temperature gradient on the solidification of eutectics. INTERLAMELLAR SPACING It has been shown previouslyg that the micro-structure of the decanted interface and the longitudinal section of the Mg-A1 eutectic is characterized by the presence of both lamellar and rod-like morphologies. The lamellae become more regular as the freezing rate is decreased. A three-dimensional photomicrograph representing a perfect lamellar morphology is illustrated in Fig. 1. The lamellae of the top and longitudinal sections of the specimen are regularly spaced while those in the transverse section are not quite straight and parallel. Their parallelism is slightly distorted because fault lines producing a discontinuity are present. A method for calculating the interlamellar spacings A, is described in Appendix 1. The true

Jan 1, 1962

By WALTER B. JONES

PIG iron was first produced in Alabama in 1818 from limonite or brown ore and since then much of this ore has come from the so-called mineral district of northern Alabama, especially along the Cretaceous-Paleozoic contact. For many years the Russellville district in Franklin County, where the first blast furnace was erected, produced more than 100,000 tons of brown ore annually. Limonite has been reported at many places in the Coastal Plain region, where the formations are of Mesozoic and Cenozoic age, but these scattered deposits were never considered to be of much commercial importance. However, in the last three years a considerable quantity of this ore has been scraped up and shipped, particularly from the city of Greenville in Butler County.

Jan 1, 1938

By AIME AIME

M ALBERTSON is research engineer for the Shell Petroleum COT. He joined the Roxana Petroleum Corp. (later the Shell) in 1920, at Hanger, Texas, became district geologist at Shreveport, and after two years was transferred to the production department, where he has been for the past fifteen years. His jobs have ranged from a modest field engineer up to assistant production manager. During this time hc has successively resided in Texas, Louisiana, Missouri, Louisiana, Oklahoma, Missouri, Texas, The Hague (Holland), and Texas. II? the Yates Pool, Texas, in 1929, "Al" initiated' the tubing of wells under pressure to control gas-oil ratios, particularly at restricted rates of flow. This led to the compulsory tubing of all oil wells drilled in the State

Jan 1, 1937

By AIME AIME

NOTWITHSTANDING the metropolitan appearance of M. L. Haider, the present Chairman of the Petroleum Division, he is not a native New Yorker, but was born at Mandan, N. Dak., Oct. 1, 1904. He began his travels at an early stage in life and after attending the University of Southern California for two years he spent two additional years at Stanford University and was graduated in 1927. After a few months as an analytical chemist for the Portland Cement Co. he became research engineer in the natural gasoline department of the Richfield Oil Co. where he remained for approximately two years before taking a position with the Carter Oil Co. in Oklahoma. He was chief engineer for this company for three years before being trans-

Jan 1, 1945

By A. English, M. J. Greaves

This paper is a discussion of pelletizing systems developed over the last 15 to 20 years for the agglomeration of fine iron ore concentrates. Five different pelletizing systems are now in commercial use in the U.S., and for the purposes of comparison, estimated operating costs and capital costs for the construction of four of them are included. Capacities of existing commercial plants are examined, together with the anticipated capabilities of plants presently being built or projected. In just 21 years, the art of pelletizing iron ore concentrates has reached maturity with mastery of the separation of finely divided concentrates from low-grade iron ores and their agglomeration into pellets containing about 65% iron. This accomplishment has firmly established an improved feed for the blast furnace, with resulting benefits in faster reduction of burdens and greater economy of operation. The present production capacity of pelletizing facilities in the U.S. is about 20 million tons annually, and it is expected to double by 1970. The rapid expansion of pelletizing in the U. S. has been closely observed in European countries, notably in Sweden and Germany, where pioneer agglomerating techniques were developed early in this century. PELLETIZING PLANTS AND PROCESSES Twelve commercial pelletizing plants are presently in operation in the U. S. and Canada. An equal number are in various stages of engineering and construction, and many others are being considered. The pelletizing systems currently employed include shaft furnaces, horizontal grates using three different airflow arrangements, and grate kilns. The capacity of pelletizing operations in North America is shown in Table I. All of these plants are integrated with the mine, the ore-crushing facilities and the concentrating plant and are equipped with storage and loading-out facilities for the product. Normally, a pelletizing plant is composed of a shuttle conveyor above the receiving bins; balling equipment; a heat-hardening system including the necessary auxiliaries such as furnaces, burners and controls, ducts, fans, meters and instrumentation; fines recovery equipment; and product handling equipment. Also included are the necessary auxiliaries and utilities such as boilers or power plant; oil unloading and storage facilities; coal unloading storage, grinding and distribution facilities; and bentonite or other additive storage and distribution equipment. Shaft Furnaces: Vertical shaft furnaces used in this country are limited to the treatment of natural magnetite concentrates containing minor quantities of residual fluxing elements. Fig. 1 shows a perspective view of the shaft furnace with balling, feeding and pellet-handling equipment. An elevation of a shaft furnace is shown in Fig. 2. A commercial shaft furnace unit is about 45 ft in height with a 6 x 14-ft rectangular cross section and has a nominal production rate of approximately 50 gross tons of pellets per hour. The upper portion of the furnace shaft is constructed of fire brick as protection from the high process temperatures involved. The lower portion of the shaft is lined with abrasion-resistant brick to withstand erosion from the fired pellets. Rectangular-shaped, refractory-lined and insulated combustion chambers are situated on each side of the shaft furnace. Oil or gas is burned to produce high temperature gases which are forced into the furnace through ports located near the top of the combustion chambers. The shaft furnaces operate at a pressure of approximately 6 psi. Pellets are fed into the top of the furnace by a pantographic feeder designed to produce the desired pellet stockline. The furnace is kept filled at all times and pellets are fed and discharged from the furnace at the same rate. In early development, 10 to 12 lb of solid fuel was incorporated in the pellets. However, the main source of process heat is now derived from the combustion chamber gases. In some instances no solid fuel is used. The pellet movement in the shaft furnace is counter-current to the flow of gases. Ambient air is introduced through louvers at the lower end of the furnace, at about 6 psi, cooling the fired pellets and supplementing the heat of the high temperature gases from the combustion chamber ports. The zone of maximum temperature, located above the ports of the combus-

Jan 1, 1963

By L. W. Kempf

DURING the recent development of aluminum alloys for free-cutting screw-machine rod, it became desirable to know something of the solubility of lead and bismuth in liquid aluminum and in some aluminum alloys. The literature is not particularly helpful in supplying this information. These portions, therefore, of the constitutional relationships of aluminum-ismuth and aluminum-lead alloys were investigated by thermal analysis and by chemical analysis of samples taken from aluminum-rich melts in equilibrium with precipitated lead or bismuth. The solubility of lead and bismuth in some liquid aluminum-copper alloys was also investi-gated. Some consideration was also given to the solubility of these elements in solid aluminum. Among the earliest investigators of the aluminum-lead and aluminum-bismuth systems was Wright,1 who reported that melts of aluminum and lead formed two layers indicating limited liquid solubility. Under his conditions, the aluminum-rich layer was reported to contain 1.91 per cent Pb and the lead-rich layer, 0.07 per cent Al. Subsequently, Pecheau2 found that in aluminum-rich alloy melts with more than 10 per cent Pb three layers were distinguishable. He reported that the middle layer contained from 3 to 10 per cent Pb. He also found that the melting point of aluminum appeared to be lowered slightly by the addition of lead. Gwyer3 investigated these alloys and found evidence of a slight lowering of the freezing point of aluminum by the addition of either lead or bismuth. He found no evidence of solid solubility in either case and made no attempt to determine the liquidus curves. Hansen and Blumen-thal4 reported that the addition of lead distinctly lowered the solidifica-tion point of aluminum. They also found that bismuth lowered the melting point of aluminum. Guillet5 reported almost complete mutual immiscibility for the aluminum-bismuth alloys in the liquid state. Bohner6 examined the effect of various concentrations of lead and bis-muth on the electrical conductivity of aluminum. He found decreases in conductivity on annealing at 500° C. as compared with the conductivity of the same alloys on annealing at 300° C.

Jan 1, 1938

By K. L. Meissner

It is well known that the so-called pure aluminum contains noticeable amounts of impurities, chiefly iron and silicon, and many investigators have studied the forms in which these impurities exist. Hanson and Archbutt1 state that iron exists in aluminum as FeA13 and silicon as elementary Si. The solubility of FeA13 in solid aluminum is practically zero, or at least so small that the smallest trace of this compound is always visible as a separate constituent. Under the microscope an untrained eye can hardly distinguish, without etching, the two constituents FeA13 and Si, but they can be differentiated by suitable etching reagents. Anderson2 also found the same results. At the same time, Merica, Waltenberg, and Freeman3 found a constituent of unknown composition. They found a small thermal effect, at 610" C., on the cooling curves of aluminum with small amounts of iron and silicon. The intensity of this effect increased with increasing silicon content, until an effect occurred at 576" C. due to the eutectic between aluminum and silicon. The authors ascribed the effect at 610" C. to a compound, which they call "X constituent." It was thought to be a ternary compound containing iron and silicon and could be observed under the microscope as dark particles. Dix4 has published unetched photomicrographs of an aluminum with 0.51 per cent. iron, 0.99 per cent. silicon, and 0.32 per cent. copper that shows three constituents: the dark Si (black in the figure), the lighter FeA13, which appears in half tone and crystallizes in needles, and a constituent of the same color as FeAL3 but of different crystal form, often resembling Chinese script. This last constituent, Dix thought, is a compound of Fe and Si; not the compound FeSi but a compound containing a relatively small amount of silicon. Therefore an alloy of aluminum. iron, and silicon (the copper should not be regarded in the following considerations) must contain the following four constituents: Al, FeA13, Si, and a compound of Fe and Si. This, however, does not agree with the laws of chemical equilibrium.

Jan 1, 1926

By Charles M. Ryder

IN presenting this paper to the Institute I beg to mention, first, the results which I have obtained and the apparatus which I have employed, and to follow this with a brief description of the steps by which I have perfected this process. My present mode of testing is as follows : I obtain, either from the furnace or from the finished product in any stage in which it may chance to be, a small test-piece, usually about 4 of an inch square by 3 1/2 inches in length. I place this test-piece upon the poles of an ordinary electro-magnet, for about one minute, and thus magnetize it to its extreme limit. I then place it upon an indicator (which I will shortly describe), on which indicator there is already placed a piece of steel of similar form which has been magnetized in the same manner, the percentage of carbon of this second piece being definitely known. I then, by means of a scale, which forms part of the indicator, marked in degrees of carbonization, read the exact percentage of carbon contained in the piece under examination. My apparatus consists of an ordinary electro-magnet, connected with a suitable battery of moderate power, by which I magnetize the pieces as before described, and of an indicator which consists of a magnetic needle suitably mounted or suspended, so that it is free to deviate a few degrees only from the zero point, and having a rest, which is used to check the vibrations when in use, and to support its weight when not in use. At a right angle to the natural position of the needle I have a scale about 3 feet long, the zero point of which coincides with the natural position of the needle. This scale is marked in each direction from the zero point in degrees of carbonization. The marking of the scale is in accordance with the following rule: Taking the carbonization of the steel as a basis, I maintain the same proportion between the squares of the distances on the scale as exists between the percentages of carbon in the steel, for instance, if .08 of

Jan 1, 1877

By Henry Rogatz

Oil.—During the year 1938, there were 434 oil wells drilled in the Texas Panhandle, increasing the daily initial production by 192,706 bbl. —that is, 229 fewer oil wells drilled than in the previous year, with a decrease in total daily initial production of 129,626 bbl. The total daily potential of the field on Dec. 1, 1938, as determined by the Texas Railroad Commission, was 1,250,645 bbl., an increase of 210,663 bbl. over the previous year. On Dec. 1, 1938, the daily allowable of 82,466 bbl. was assigned to the field to be produced from 3931 wells. The total amount of oil produced for the year was 23,227,170 bbl. The total proven productive area includes 148,298 acres. This is 30,248 acres more than for last year, and represents a more accurate calculation of the areas and not new discoveries. Gas.—There were 103 gas wells drilled during 1938, having a combined open flow of 3,166,300,000 cu. ft.; that is, 65 less than the number of wells drilled in 1937, with a decrease in the open flow of 3,144,488 cu. ft. per day. Pipe-line Gas.—The pipe-line companies withdrew 230,307,854,000 cu. ft. of gas (a daily average of 630,980,000 cu. ft.). The total withdrawals by pipe line decreased 5,624,481,000 ft. from that of 1937. Natural Gaso1ine.—Throughout the greater part of the year, 46 gasoline-extraction plants processed 1,376,186,000 cu. ft. per day, a total of 502,308,010,000 cu. ft. for the year. This gas yielded about 275,875,000 gal. of natural gasoline. The total daily capacity of all the plants is 2,519,500,000 cu. ft. During the latter part of 1938, one of these plants was shut down, leaving 45 plants operating at the close of the year. Carbon Black.—Thirty carbon-black plants operated during 1938, burning 266,881,000,000 cu. ft., or a daily amount of 731,180,000 cu. ft. This produced approximately 400,000,000 lb. of carbon black. During the year one plant was dismantled and two plants were shut down.

Jan 1, 1939

By Henry Rogatz

Oil.—During the year 1938, there were 434 oil wells drilled in the Texas Panhandle, increasing the daily initial production by 192,706 bbl. —that is, 229 fewer oil wells drilled than in the previous year, with a decrease in total daily initial production of 129,626 bbl. The total daily potential of the field on Dec. 1, 1938, as determined by the Texas Railroad Commission, was 1,250,645 bbl., an increase of 210,663 bbl. over the previous year. On Dec. 1, 1938, the daily allowable of 82,466 bbl. was assigned to the field to be produced from 3931 wells. The total amount of oil produced for the year was 23,227,170 bbl. The total proven productive area includes 148,298 acres. This is 30,248 acres more than for last year, and represents a more accurate calculation of the areas and not new discoveries. Gas.—There were 103 gas wells drilled during 1938, having a combined open flow of 3,166,300,000 cu. ft.; that is, 65 less than the number of wells drilled in 1937, with a decrease in the open flow of 3,144,488 cu. ft. per day. Pipe-line Gas.—The pipe-line companies withdrew 230,307,854,000 cu. ft. of gas (a daily average of 630,980,000 cu. ft.). The total withdrawals by pipe line decreased 5,624,481,000 ft. from that of 1937. Natural Gaso1ine.—Throughout the greater part of the year, 46 gasoline-extraction plants processed 1,376,186,000 cu. ft. per day, a total of 502,308,010,000 cu. ft. for the year. This gas yielded about 275,875,000 gal. of natural gasoline. The total daily capacity of all the plants is 2,519,500,000 cu. ft. During the latter part of 1938, one of these plants was shut down, leaving 45 plants operating at the close of the year. Carbon Black.—Thirty carbon-black plants operated during 1938, burning 266,881,000,000 cu. ft., or a daily amount of 731,180,000 cu. ft. This produced approximately 400,000,000 lb. of carbon black. During the year one plant was dismantled and two plants were shut down.

Jan 1, 1939

By George C. Stone

The stack gases from regenerative furnaces lare very seldom utilized for the production of steam. If the temperature of the gases is not higher than 300" C. (572" F.) there is no economy in their use for this purpose, as the amount of available heat is very small and the temperature is so little above that of the steam that the interchange is too slow. With higher temperatures of the waste gases, however, good results can be obtained. At the plant of the New Jersey Zinc Co. (of Pa.) at Palmerton there are a number of return tubular boilers, each 6 ft. in diameter and 20 ft. long, with 96 3.5-in. tubes, which are heated by the waste gases from the spelter furnaces. These furnaces have continuous regenerators heating the air only and the stack gases reach the boilers at a temperature of about 450". The gas producers for one of these furnaces require 14 tons of anthracite (a mixture of Nos. 2 and 3 buckwheat), and the waste heat from the furnace gives a little more than 42 h.p. in steam. The boilers are not well adapted for the purpose, as they are much too large for the amount of heat going to them and the area of the tubes is not sufficient to take the gas from two furnaces without causing an objectionable amount of back pressure. The plant was built without any idea of using waste-heat boilers, and it was impossible to place the latter as close to the furnaces as they should be. Furnace and boiler are connected by an underground brick flue in which the temperature of the gas drops about 100°, losing 40 per cent. of its available heat. If the boilers were close to the furnaces the horse power of each would be 70 instead of 42. Even under these unfavorable conditions the boilers have been very advantageous, as one boiler easily supplies the steam necessary for two batteries of producers. With such low gas temperatures the heating surface of the boilers is, of course, not as efficient and the flue areas need to be considerably larger than for coal firing.

Jan 1, 1914

By John L. Schroder

The demands for increased productivity on the 1967 coal industry have generated new operating trends and fresh approaches to old methods, which have enabled the industry to keep pace with the expanding economy. Changes, while not radical in concept or design, have been plentiful and are marked by the refinement of the already tried, tested and proven. Perhaps not since World War II have there been demands on equipment manufacturers to design and deliver such diversified types of machines as those required by the industry in the past year. Equipment developments-following a plan which calls for higher productivity, lower maintenance costs and greater machine availability- have tended more toward increased horsepower and heavier, more rugged equipment. Electrical and mechanical components, designed in many instances with maximum reliability rather than initial costs as the main criterion, have contributed to the improvements in over-all performance. High-strength, specialty steels are finding use in a wide range of equipment applications. The horsepower capacity of electric motors being installed is more frequently being rated on a continuous basis rather than the former one hr or less and, as a result, fewer failures now occur because of overloading. These developments reflect the pyramiding cost of equipment down-time and represent definitive progress in reducing the magnitude of the problem.

Jan 2, 1968

By Paul A. Schafer

BaLatoc mine, the principal gold-producing mine in the Philippines, is 10 miles southeast of Baguio, in the Cordillera Central of northern Luzon.' The region is a deeply dissected plateau, ranging in altitude from 3000 to 5000 ft. above sea level. The rocks consist chiefly of granodiorite, diorite, and remnants of metamorphosed sediments, cut by dikes of andesite porphyry and quartz-diorite porphyry. All are intruded by a volcanic breccia plug, oval in horizontal section, about 3200 ft. long and 2300 ft. wide, which is the north central part of the mineralized area. Three main vein systems have been developed (Fig. I): 96, 231 and 364, which strike about N.70°E. and dip 50° to 90°S. Each system is a braided zone consisting of many individual components. They are disturbed by a series of premineral faults or shear zones striking about N.4s°E. Twelve of these produce important effects on the persistence, character, and quality of veins. From west to. east the faults are named (after claims): Hog, Big Gun, Bull, Pine, Lolita, Bar No. I, Bar No. 2, Curt, Sun, Helen, Itoe, and Frog. They are early breaks formed prior to the N.70°E. vein fractures. Mineralization occurs on them but, with several prominent exceptions, they are too low grade to mine. A number of northwesterly striking faults complete the structural pattern. Although they are relatively abundant, the effect on the veins is so small that they do not present any problems in mining or development. All of these faults that have been observed are later than the N.70°E. veins and offset them to the left. Northeast Faults The early northeast faults* are notably continuous in spite of their small displacements, 20 to 100 ft. Frequently they appear so weak that their importance is masked and their identity clouded. The gouge along any of these faults may vary from exceedingly weak at one point to very strong at another point only a short distance away. In other words, the amount of gouge depends on the changes of attitude of the fault plane, and is no indication of the extent of the movement. Places where walls are spread apart are filled with gouge squeezed from tight places. Also, mineralization sometimes obscures fault gouges by replacement. The mineralization of northeast faults has produced several important ore bodies; namely, 231 west on On fault and 96 vein on the same fault. To a smaller extent, Lolita, Curt, Bull, Bar NO. I, and Sun

Jan 1, 1949

By Paul A. Schafer

BaLatoc mine, the principal gold-producing mine in the Philippines, is 10 miles southeast of Baguio, in the Cordillera Central of northern Luzon.' The region is a deeply dissected plateau, ranging in altitude from 3000 to 5000 ft. above sea level. The rocks consist chiefly of granodiorite, diorite, and remnants of metamorphosed sediments, cut by dikes of andesite porphyry and quartz-diorite porphyry. All are intruded by a volcanic breccia plug, oval in horizontal section, about 3200 ft. long and 2300 ft. wide, which is the north central part of the mineralized area. Three main vein systems have been developed (Fig. I): 96, 231 and 364, which strike about N.70°E. and dip 50° to 90°S. Each system is a braided zone consisting of many individual components. They are disturbed by a series of premineral faults or shear zones striking about N.4s°E. Twelve of these produce important effects on the persistence, character, and quality of veins. From west to. east the faults are named (after claims): Hog, Big Gun, Bull, Pine, Lolita, Bar No. I, Bar No. 2, Curt, Sun, Helen, Itoe, and Frog. They are early breaks formed prior to the N.70°E. vein fractures. Mineralization occurs on them but, with several prominent exceptions, they are too low grade to mine. A number of northwesterly striking faults complete the structural pattern. Although they are relatively abundant, the effect on the veins is so small that they do not present any problems in mining or development. All of these faults that have been observed are later than the N.70°E. veins and offset them to the left. Northeast Faults The early northeast faults* are notably continuous in spite of their small displacements, 20 to 100 ft. Frequently they appear so weak that their importance is masked and their identity clouded. The gouge along any of these faults may vary from exceedingly weak at one point to very strong at another point only a short distance away. In other words, the amount of gouge depends on the changes of attitude of the fault plane, and is no indication of the extent of the movement. Places where walls are spread apart are filled with gouge squeezed from tight places. Also, mineralization sometimes obscures fault gouges by replacement. The mineralization of northeast faults has produced several important ore bodies; namely, 231 west on On fault and 96 vein on the same fault. To a smaller extent, Lolita, Curt, Bull, Bar NO. I, and Sun

Jan 1, 1949

By Andrew Corry

GEOPHYSICAL investigations based on radioactivity have been applied to the earth's crust for the purpose of discovering bodies rich in radioactive substances, or for the location of solutions with high emanation or radioactive-salt content, or for the detection of oil, which, in virtue of colloidal properties, has strong powers of radioactive absorption. RADIOACTIVE SUBSTANCES Radioactive substances are distributed in all rocks, waters, and gases in the earth's crust in small quantities. Granites and similar acidic rocks are richest in uranium and thorium, two chief radioactive substances; yet the quantities present in such rocks are of the order 10-12g., this concentration being expressed in grams per gram of the whole substance per cubic centimeter. In granites the uranium yields, according to Haddock, 3 X 10-12 g. of radium per gram of rock. In basalts the uranium yields 1.19 X 10-12 g. per gram per cubic centimeter. Of thorium the granites yield -2 X 10-5 g. per gram of rock; the basalts, 0.77 X 10-5 g. per gram. Certain series of alkalis of low atomic weight, like potassium and rubidium, show weak radioactivity; this property has no significance so far for geological research. The uranium is esti-mated indirectly from the electrical properties of one of its derivatives as a -gas (emanation) into which it is transformed. The thorium is expressed directly, though it is measured as a derivative, thorium emana-tion. There is a measure for the gaseous radium emanation, the curie, which is that quantity of radium emanation, or radon, which stands in equilibrium with 1 g. of radium. The concentration of the emanation is the Mache unit corresponding to 3.64 X 10-10 curie per liter. When gases become permeated by alpha, beta, and gamma rays, plus and minus ions are produced in them by the decomposition of neutral gas molecules, and under the influence of an electrical field these ions are given opposite motions. The measurement of the alpha rays and the bisection thicknesses of the beta and gamma rays is a means of analyzing unknown radioactive substances. These rays accompany the disintegration of radioactive substances and arise from "spontaneous internal changes

Jan 1, 1929

R. M. Raymond, New York, N. Y.—The filling and drawing down of the overhead material was done at considerable depth, which is not the usual method in which it starts at the surface.. R. J. Mechin.— It is a little more than 1000 ft. at El Bordo. The vein above had been caved practically to the surface and some of the ore had been excavated, using underhand and overhand square-set methods. This was far enough away from the shaft to prevent any bad effects. When the sill floor was taken out, to insure the old cave material following down well, we put chutes in the square sets for several weeks until we were sure that the material from above was moving down; on each level above, several crosscuts were driven into the old fill by which we could see the material coming down and thus be sure it was following the first. We had to dynamite it very little because it was dry and dusty. The only trouble was that timber starting from the old square sets would get across the chute and hang up. R.. M. Raymond.—HOW many floors did you operate at once? R.. J. Mechin.—We would operate one floor through the whole length and prepare for the second. F. W. SperR, Houghton, Mich.—Could you have worked it in steps? R.. J. Mechin.—Yes; but working it all on one floor was much better for ventilation. The passage between steps would tend to become heavy and blocked and, as the passages from the mining floor down are usually filled with ore, there would be no way for the air to pass up. By means of doors and fans, air was driven to the extreme end of the orebody through the stope and up the other end; but it could have been worked in steps. F. W. SpeRR.—D the following-up material ever become so heavy that you could see weight on the caps before you had to take out the posts?

Jan 1, 1927

By F. J. Tuck

The Hayden mill of the Ray Mines Division, Kennecott Copper Corporation, is now equipped with two 9 by 12-ft. rod mills having a daily capacity of 6000 tons of coarse-crushing plant product from the mine. These two mills crush a ¾-in. product to approximately 19 per cent on 14 mesh, with only one pass through the mills. Each rod mill has taken the place of four sets of 42-in. Garfield rolls with their attendant screens, and is making a product for the fine-grinding department comparable to that formerly made by rolls in closed circuit with screens. The rod mills are lined with wave-type liners of white iron, varying in thickness from 2 to 3 in. The shell and end liners last approximately 600 to 700 days. Manganese-steel lifter bars, 3? in. thick, are used, spaced about 11 in. apart, and they give a life of 350 to 450 days. Fig. 1 shows the general design and thickness of the wave-type liners and lifter bars; 1½-in. liner bolts are used to fasten the lifter bars to the shell. The shell liners are held in place by the tapered lifter bars. A ¾-in. wood backing is used between the shell and the liners. The rod-mill scoop has removable manganese-steel lips, which last 250 to 300 days. The scoop proper has shown some wear in spots, and these spots have been protected by rubber bolted over them. Water and milk of lime are added to the elevator feeding the mill, but not enough water to cause a pounding of the rods against the shell. Roughly, the water added amounts to 25 to 33 per cent of the ore. Additional water is added to the mill discharge to facilitate distribution to the classifier bowls in the fine-grinding department. Rods are charged to the mill once every four days, the mill being down about 20 min. for this purpose. Other delays are negligible, and usually are due to a loose liner bolt or possibly power trouble. However, these occasions are extremely rare. In charging the mill, a crane is used

Jan 1, 1939

By F. J. Tuck

The Hayden mill of the Ray Mines Division, Kennecott Copper Corporation, is now equipped with two 9 by 12-ft. rod mills having a daily capacity of 6000 tons of coarse-crushing plant product from the mine. These two mills crush a ¾-in. product to approximately 19 per cent on 14 mesh, with only one pass through the mills. Each rod mill has taken the place of four sets of 42-in. Garfield rolls with their attendant screens, and is making a product for the fine-grinding department comparable to that formerly made by rolls in closed circuit with screens. The rod mills are lined with wave-type liners of white iron, varying in thickness from 2 to 3 in. The shell and end liners last approximately 600 to 700 days. Manganese-steel lifter bars, 3? in. thick, are used, spaced about 11 in. apart, and they give a life of 350 to 450 days. Fig. 1 shows the general design and thickness of the wave-type liners and lifter bars; 1½-in. liner bolts are used to fasten the lifter bars to the shell. The shell liners are held in place by the tapered lifter bars. A ¾-in. wood backing is used between the shell and the liners. The rod-mill scoop has removable manganese-steel lips, which last 250 to 300 days. The scoop proper has shown some wear in spots, and these spots have been protected by rubber bolted over them. Water and milk of lime are added to the elevator feeding the mill, but not enough water to cause a pounding of the rods against the shell. Roughly, the water added amounts to 25 to 33 per cent of the ore. Additional water is added to the mill discharge to facilitate distribution to the classifier bowls in the fine-grinding department. Rods are charged to the mill once every four days, the mill being down about 20 min. for this purpose. Other delays are negligible, and usually are due to a loose liner bolt or possibly power trouble. However, these occasions are extremely rare. In charging the mill, a crane is used

Jan 1, 1939

By James C. Fulton

Since publication of the First Edition of "Basic Open Hearth Steelmaking," in 1944, this book has been a major reference on the subject of steelmaking. The Second Edition of 1951 was so fundamental that it has retained its general usefulness to the present date. However, recently some of the material has been updated in connection with the writing of a companion book, "Electric Furnace Steelmaking." The sponsor of these two books, the Physical Chemistry of Steelmaking Committee, has felt that the new material should be made equally available to purchasers of either book. Accordingly the subject matter of Chapters 14, 15, and 16 of this new edition is duplicated by corresponding chapters in "Electric Furnace Steelmaking." It was also recognized that the use of oxygen in the open hearth and in the new basic oxygen processes represents a major development that should not be omitted from any basic reference. Thus the major new feature of this Third Edition is the supplement on "Oxygen in Steelmaking." The cooperation of the Iron and Steel Division's Acid Converter and Basic Oxygen Steel Committee (now merged to form the National Open Hearth and Basic Oxygen Steel Committee) is specifically recognized. In addition to the authors of chapters listed elsewhere, it should be noted that Arthur B. Wilder was the Committee Chairman. Although the changes in the Third Edition are important, the Committee cannot overlook the classic character of the Second Edition. This edition was edited by W. O. Philbrook and M. B. Bever in collaboration with H. B. Emerick and B. M. Larsen. It is anticipated that the Third Edition will maintain the value of the book until the current rapid changes in all basic steelmaking processes stabilize themselves sufficiently to justify a complete revision of the entire text in Part I. The experienced service of Wesley Burr in incorporating the new material in the index is also recognized.

Jan 1, 1964

By P. Barnes

It may he of interest, and perhaps of inzportance, to the members of the Institute that specific mention should be made in detail of the great value of this method of copying or photographing all kinds of tracings." Several samples are laid upon the table which may serve as illustrations of the results obtained. Some of these show slight imperfections, depending upon the character of the tracing, and upon the length of the exposure to the light, but it may be clearly seen that even a faint copy would be quite available for actual use. The process is believed to be of French origin, and has been used for many years. Special attention seems to have been directed to it recently, and its great value to engineers appears likely to be fully recognized. The manipulations required are of the simplest possible kind, and are entirely within the skill and comprehension of any office boy who can be trusted to copy a letter in an ordinary press. These particulars may be summarized somewhat thus: 1. Provide a flat board as large as the tracing which is to be copied. 2. Lay on this hoard two or three thicknesses of common blanket, or its equivalent, to give a slightly yielding backing for the paper. 3. Lay on the blanket the prepared paper with the sensitive side uppermost. 4. Lay on this paper the tracing, smoothing it out as perfectly as possible so as to insure a perfect contact with the paper. 5. Lay on the tracing a plate of clear glass, which should be heavy enough to press the tracing close down upon the paper. Ordinary plate-glass of 3/8" thickness is quite sufficient. 6. Expose the whole to a clear sunlight, by pushing it out on a shelf from an ordinary window, or in any other convenient way, for six to ten minutes. If a clear skylight only can be had, the exposure must be continued for thirty or forty-five minutes, and under a cloudy sky, sixty to ninety minutes may be needed.

Jan 1, 1879