Search Documents

By F. F. Aplan, P. H. de Bruyn

The adsorption density of hexyl mercaptan was measured at the gold-solution and the gold-vapor interfaces. This collector is strongly adsorbed at low concentrations, a monomolecular layer being formed at the gold-solution interface at concentrations as low as 2 x 10'6 moles per liter. A maximum contact angle of 83 ± 3° is observed. From a thermodynamic analysis of the experimental data the changes in surface tension at the gold-gas and gold-solution interface are calculated. The data also suggest that the adsorption density of mercaptan at the gold-gas interface exceeds that at the gold-solution interface. In the equilibrium state, a simple flotation system consists of three phases, the solid to be floated, air, and an aqueous solution in stable contact along a line. During the process leading to this final state, a solid-gas interface is created at the expense of a portion of the liquid-gas and solid-liquid interfaces. This change of state is achieved by addition of a collector and, if necessary, suitable modifying agents to the system. By a combined application of the Gibbs Adsorption and the Young Equations, de Bruyn, Overbeek and Schuhmannl were able to show theoretically that the equilibrium distribution of the collector at all three interfaces determines the magnitude of the contact angle. Their analysis led them to conclude that the equilibrium adsorption density of the collector at the solid-gas interface exceeds its density at the solid- liquid interface. This paper succeeded in focussing attention on the neglected role of the solid-gas interface in flotation. In recent years the application of radiotracer, infrared, electrochemical and electro-kinetic techniques to studies of the solid-liquid interface2-5 enhanced our understanding of adsorption processes at this interface. Except for the measurement of contact angles, the solid-gas interface received no attention in fundamental flotation studies. In an attempt to apply the analysis of de Bruyn, Overbeek and Schuhmann to a simple flotation system, an investigation of the adsorption of hexyl mercaptan onto gold was undertaken. Gold was chosen as the solid phase in order to keep the number of dissolved chemical species in the solution phase to a minimum. Hexyl mercaptan (1 - hexanethiol) was selected as collector because its relatively high vapor pressure at room temperature makes it possible to obtain adsorption measurements at the solid-gas interface. This flotation system consists, therefore, of a pure solid phase (gold), an aqueous solution of a weakly dissociated collector (1 -hexanethiol), and a gaseous phase, nitrogen saturated with respect to both water vapor and mercaptan vapor. EXPERIMENTAL MATERIALS AND METHODS Materials: Liquid 1-hexanethiol (C6H13SH) was obtained from Distillation Products Industries and was further purified by double distillation. The purity of the final product was established by boiling point and refractive index measurements. For the adsorption studies from aqueous solution, the radiotracer element, sulfur-35, (half life 87.1 days, 0.169 Mev beta ray) was synthesized into the mercaptan by Tracerlab Inc., Boston, Mass. A close boiling fraction of the synthesized compound was used in the adsorption studies. The specific activity of the radioactive compound was 10 millicuries per gram.

Jan 1, 1963

By Robert J. Hite, Samuel S. Adams

Potash, the generic term for a variety of potassium-bearing minerals, ores, and refined products (Table 1), owes its importance as an industrial mineral to the potassium requirement of growing plants. The term potash originally referred to potassium carbonate produced by the leaching of wood ashes. This process, for which the first US patent was issued in 1790, was the basis for the largest United States chemical industry in the early nineteenth century. The agricultural use of potash soon eclipsed the chemical applications following the German discovery in 1840 that potassium is essential to plant growth. The initial discoveries of large deposits of soluble potassium minerals, essential for agriculture applications, were made in 1857 in Germany and in 1914 in the United States. More than 90% of the 27.5 Mt K20 produced in the world in 1980 (Searls, 1981) was derived from marine evaporite deposits and approximately 90% was used in fertilizers. The potassium content of an ore, mineral, or product is customarily expressed as % K20, a unit of measure which is neither a natural nor synthetic compound of potassium (1.0% K is equivalent to 1.2046% K2O). Geology Potassium, the seventh most abundant element in the earth's crust, is present in silicate minerals in igneous, sedimentary and metamorphic rocks. Potassium is also a major constituent of many surface and subsurface brines (Table 2). Economic potash deposits are essentially restricted, however, to widespread, thick accumulations of marine chloride evaporite deposits. These deposits yield high grade, large tonnage ore bodies, many of which are amenable to low cost mining and beneficiation. The products from these deposits are, moreover, ideal for use in fertilizer because of the high relative solubility of the potassium chloride and sulfate evaporite minerals. World potash production and reserves for such deposits so vastly overshadow other sources of potassium that the following discussion will be limited largely to potash deposits in marine evaporites with brief reference to certain potash-rich brines. Approximately 85% of current domestic production is from bedded salt deposits and much of the balance is from brines. Marine evaporite deposits are accumulations of salt minerals deposited in structural sedimentary basins through the evaporation of seawater or mixtures of seawater and other brines. The salt minerals are precipitated in assemblages and sequences of assemblages as determined by the compositions of the brines and the solubility relations in the salt systems (D'Ans, 1933). The evaporation of seawater normally yields carbonate minerals as the first precipitates (Table 3). Further evaporation and concentration of the brine leads to the precipitation, in succession, of sulfate, chloride, and supersaline mineral assemblages including the salts of potassium and magnesium. The common minerals, ores, and products of potassium deposits are listed in Table 1. Many potash deposits contain accessory evaporite minerals together with a variety of detrital and authigenic silicates (Braitsch, 1971). The structural basins within which marine evaporites occur are of two main types: (a) cratonic basins formed by broad epirogenic movements (for example, the Michigan Basin of the midwestern United States and the Permian Zechstein Basin of eastern Europe), and (b) grabens, commonly related to continental

Jan 1, 1983

By D. J. Carney, J. Chipman, N. J. Grant

An absolute calibration has been achieved for sampling and analyzing liquid steel for hydrogen based on Sieverts' values of hydrogen solubility in iron. Further checks were made in nickel, iron-nickel, and 18-8 stainless melts. The sampling method was successfully applied to a large number of commercial steel melts in various types of furnaces. The concurrent problem of sample storage was also solved. THE problem of sampling of liquid steel for hydrogen is more difficult than the problem of analysis. Hydrogen has a greater mobility than any other element; it is the only element that will diffuse out of steel at room temperature. In accordance with the known relation between temperature and diffusivity, the diffusion of hydrogen is extremely rapid at the temperature of liquid steel. Consequently, in the past, attempts to quench molten steel to retain the dissolved hydrogen have not been as successful as similar attempts with nitrogen or oxygen. The retention of hydrogen is especially difficult since it will continue to escape at room temperature even if the molten metal has been rapidly quenched. The hydrogen sampling methods may be classified broadly as (1) the rapid quenching techniques which attempt to preserve super saturation and (2) those methods which attempt to collect the gases evolved as the metal freezes and cools to room temperature. With all methods of sampling but especially with the rapid quenching methods, there is also a concurrent problem of storing the sample until analysis is undertaken. The two problems are interrelated and must be considered together when discussing liquid steel sampling techniques. The major obstacle in liquid steel sampling has been that there was no way of evaluating properly the various sampling and storage techniques which have been developed. It has not been possible to compare the accuracy of the various methods. For evaluation of sampling methods some known standard is required; this may be found in the published work on the equilibrium solubility of hydrogen in liquid iron which has been determined in three separate investigations.1,2,3 The data are shown in table I. Sieverts' original method of obtaining gas solubilities involved measurement of the volume of gas required to saturate the liquid metal contained in an evacuated bulb of known volume. This procedure, improved by introduction of high frequency induction heating, has yielded reproducible results which appear to be entirely dependable. Using Sieverts' method, it has been proved for iron and other metals and alloys that the hydrogen solubility is proportional to the square root of the pressure of the hydrogen gas above the liquid, so that one may work with various partial pressures of hydrogen to put different amounts of hydrogen in solution. From Sieverts' law it is possible to know accurately what amount of hydrogen is dissolved in the liquid metal at the time of sampling. The accuracy of a sampling method may be gauged by reference to this known solubility. It was the purpose of this investigation to develop a method for sampling liquid steel and for storing the sample so that the analytical result would represent the actual hydrogen content of the metal bath. For this purpose an induction furnace was

Jan 1, 1951

By Arthur F. Taggart

RECENT jig practice has shown such marked departures from the pronouncements of the textbooks, particularly as to particle size recovered and size range of feed, as to make it desirable to reexamine the mechanism of jig action. This paper presents the results of such a study. The general conclusions of the paper are: I. A jig bed is a bi-functioned as well as bi-parted body. The upper layer comprises a plastic stream moving slowly in a substantially horizontal direction from feed lip to tail board. It serves to rough out tailing and light middling and to pick up heavy middling and lift it out of the jig box. The lower layer acts as the ultimate separating means by absorbing concentrate and rejecting heavy middling. 2. The separating function of the lower layer is performed in three definitely different ways, depending upon the relative sizes of the grains presented to it and those composing it. EXPERIMENTAL The experimental work consisted of close and long-continued visual observations of operating beds in a plunger jig, eccentric driven, and in determinations of the settling rates of various metal spheres through a quartz bed under various conditions of operation. Falling velocities were measured by an ingenious method devised by A. C. Dorenfeld, a student in the Mining Department at Columbia. Spheres of different metallic alloys, Y8-in. diameter, were cast with a short piece of fine copper wire frozen in to serve for suspension. A short piece of black cotton thread was looped to the top of the wire to serve as an indicator. The set-up for a test is shown in Fig. I. The thread should be boiled, if necessary, to make it freely water absorbent. The piece of clean plate glass D is supported rigidly at the proper height in a vertical position. The white scale E is similarly supported behind the glass. At the beginning of a test, D is filmed with water by holding it (best with clean rubber finger cots) under running tap water. It is then clamped in approximate position and C, already wet, is laid across it and drawn straight and vertical with the upper end at or near the top of D, and the ball A slightly above the top of the expanded bed. The water film holds the string to the glass. For a test the string is released, its upper end position noted just after the top of the ball becomes submerged, when the corresponding time is read, and thereafter simultaneous readings of position and time are taken as desired. Results of the visual studies of the bed are given at the pertinent places in the following discussion. Results of the settling tests are summarized in Figs. 2 and 3. DEFINITIONS The name bed as used herein refers to the entire mixture of solids and water filling the jig box. A layer is a stratum of a bed composed of particles of substantially the same specific gravities. A granular product is long-range when it approximates a crushed or ground product limited as to upper size only; a shorlrange product is one closely sized. A bed is loaded when operating with continuous feed

Jan 1, 1943

By D. R. Shreve, L. W. Welch

An analysis for predicting the behavior of reservoirs exploited by a combined gas drive and gravity draintrge mechanism is presented. The method allows the prediction of gas-oil ratio, oil production rate, and cumlulative oil recovery for high relief pools in which pressure is maintained either by gas injection in the crest of the structure or by a combined gas and water injection program. The reservoir is represented by a model of communicating vertical prisms, with production or injection at the upper or lower boundaries of each prism. The theory of macroscopic gravitational segregation of two fluids within a reservoir is discussed in detail for all ranges of saturation. A description of an application of the analysis to a typical field problem is also presented. INTRODUCTION The importance of gravity drainage as a producing mechanism has become more evident during recent years. However, many of the reservoir engineering methods which have been used in the past for predicting the behavior of reservoirs producing by this mechanism have required such drastic, simplifying assumptions that the calculated performance in some cases does not resemble the actual pool behavior. The mechanism of fluid displacement in porous media has been described by Buckley and Leverett,1 and a simplified "one zone" method based on this development has been used by engineers to evaluate the performance of gravity drainage pools. Welge2 has modi- fied this approach so that the calculation time has been markedly decreased. In addition, many other authors3-9 have analyzed various phases of the gravity drainage producing mechanism during the past several years. In a high relief reservoir in which gravity may affect the recovery mechanism, there are two main types of exploitation programs which can be employed: 1. Reservoir pressure is maintained by injecting gas into the upper portions of the reservoir. In this case gas is not released from solution and, if dynamic pressure drops are small compared to the total pressure of the system, the gas and oil may be considered to be immiscible and to have constant fluid characteristics. 2. Reservoir pressure is not maintained and a "natural depletion" mechanism prevails. The term "natural depletion" can be used to describe the production history of a reservoir in which a gradual decline of average pressure and the associated release of solution gas continue throughout the producing life. In this mechanism gas is released throughout the reservoir and there is a continuous change in the characteristics of both the gas and the oil phases. It is the purpose of this paper to present the results of mathematical developments by which a method has been devised for evaluating the performance of reservoirs which are depleted by the first type of exploitation program discussed above. It should be mentioned that, although throughout the analysis gas and oil represent the two fluids existing in the reservoir, the method is equally applicable to gravity drainage in water-oil systems. STATEMENT OF PROBLEM In reservoirs of pronounced structural relief, where the closure of the oil section is great or the angle of

Jan 1, 1957

By Edward F. Winter, C. E. Ruoff

A silicon solid-state array image scanner is described. This paper deals with structural and performance properties of the array which basically consists of PIN photo and gating diodes, and low capacitance isolation diodes. Each chip of the array is composed of an 8 by 9 matrix of photo detector cells; each cell contains one each of the three diode types mentioned. This x-y matrix is read a column at a time with an access delay of approximately 100 nsec per column. It is designed to detect the presence or absence of illumination within 10-mil diam image spots located on a 15- by 15-mil grid. Radiant power level of an illuminated spot is low; of interest is the range around I uw with a of 8400g Structural improvements to the original array which will result THE purpose of this paper is to describe the results of a solid state scanner exploratory development activity. The scanner is intended to sense the presence or absence of low-level illumination falling upon a matrix of 10-mil wide squares arranged on a 15- by 15-mil x-y grid pattern. The light of interest has a wavelength of 8400, characteristic of radiation emitted from a GaAs lasing diode. This wavelength matches well the spectral absorption of silicon,' thus the well-developed silicon processing technology can be applied to fabricating large integrated arrays of PIN photocells to sense the radiation. The illumination state of the cells of the array is read, one column at a time, by addressing a drive line of the particular column in question and examining the state of those sense lines which are orthogonal to the drive Lines of in greater sensitivity at various wavelengths, both above and below 8400Å, and in greater speed are presented. These include variations in diffusion depth, resistivity of N and P regions, isolation techniques, and packaging. Trade-offs between access speed, cycle frequency, and sensitivity are discussed. A packaging approach to achieving an array composed of several chips is described. Requirements on this package are: 1) maintenance of 15- by 15-mil pitch of the light sensitive cell position, therefore positional accuracy of mounted 8 by 9 cell photo detector chips; 2) maintenance of inherent high array speed even though signal levels are low through high density close proximity mounting of monolithic sense amplifier circuitry. the array. One bank of N sense amplifiers is required, where N is the number of photodiode cells in each column of the array. CELL AND CHI" STRUCTURE A photograph of a single monolithic cell is shown in Fig. 1. Each cell is composed of three junctions, an isolation junction, a logic or blocking diode junction, and a photodiode junction; all of these junctions are connected electrically by a common N region. An electrical schematic of four cells of the array is shown in Fig. 2 with the associated driver and sense amplifier circuits in block diagram form. Note the common cathode configuration of the three diodes of each cell. Fig. 3, a diagram of the cell vertical struc ture, illustrates how the electrical configuration of

Jan 1, 1970

By AIME AIME

Air transport supplants the old methods. The 3-piece canoe fits in the plane and likewise makes possible not a bad division of labor over a 5-mile portage

Jan 1, 1933

By J. Wade Watkins, E. S. Mardock

The accurate evaluation of reservoir-performance characteristics in the secondary recovery of petroleum by water flooding requires use of a water tracer that may be injected into water-input wells and detected at oil-production wells to supplement data obtained from core analyses, wellhead tests, and subsurface measurements. Radioactive iodine has been used successfully as a water tracer in field tests to determine: (I) relative rates and patterns of flow of injected water between water-input and oil-production wells and (2) zones of excessive water entry into oil-production wells. Laboratory evaluations of potential water tracers, previous tracer studies, the value of using a radioactive tracer, general field procedures, and the use of surface and subsurface instruments for the detection of the emitted gamma radiation, are summarized. Data from the field tests are presented graphically and discussed in detail. It is concluded that the radioactive-tracer method, using radioactive iodine, may be used successfully to measure either the relative rates and patterns of flow or zones of excessive water entry into wells under conditions of comparatively rapid transit time between wells. INTRODUCTION Extensive use is made of data obtained from core analyses, wellhead tests, fluid characteristics, and subsurface measurements in evaluating the sweep efficiency of water injected into oil sands for the recovery of oil. Theoretical flow rates and patterns may be calculated from those data using radial-flow formulas, if it is assumed that the physical conditions in the productive formation are homogeneous. Unfortunately, homogeneous conditions rarely, if ever, exist in oil-productive formations. The use of a tracer that may be injected into an oil sand and detected quantitatively, or even qualitatively, at offsetting oil-production wells provides basic data that may be used in determining more accurately the subsurface rates and patterns of flow of injected water between wells than is possible by theoretical calculations based on assumed conditions. Consideration of the data obtained by using a water tracer assists in the application of remedial measures to water-input wells, such as plugging of channels, or selective plugging of highly permeable zones, thereby effecting a more uniform flood and a greater ultimate oil recovery. A water tracer should have the following characteristics: (1) low adsorption on solid reservoir material; (2) high solubility in water; (3) low or negligible solubility in crude petroleum; (4) a wide range of solubility of compounds that may be formed by chemical reactions with ions present in reservoir rocks or waters; (5) high detectability in low concentrations by portable apparatus; and (6) general availability at low cost. Additional desirable characteristics are that the tracer should be nonhazardous in nature under normal working conditions and quantitatively detectable in the well bore, as well as at the surface. Review of Previous Tracer Studies The need for a water tracer has been recognized for many years. As far back as 1906, Dole1 described the use of fluorescein in flow-rate studies made in France in 1901. In 1921, Ambrose" discussed in detail the use of organic and inorganic dyes, chlorides, nitrates, and other anions, lithium salts, and the Slichter electrical

Jan 1, 1955

By Michael P. Richardson

INTRODUCTION This paper is intended to be a summation of the state-of-the-art i n draw theory and draw- point spacing. Knowledge of this very important factor in the successful design and operation of a block caving mine is scarce and nonconclusive. It is hoped that the presentation of this paper will stimulate interest and discussion which will lead to a stronger understanding of these a1 1 important factors. Please note that block caving as used here- in refers to block, panel, and mass caving systems in general, not just to the specific system of block caving where discrete blocks of ore are prepared and caved as a unit. DRAW THEORY The knowledge of draw theory as related to the practice of block caving mines is, unfortunately, very limited. In recent years much work in draw theory has been done in respect to sublevel caving systems and an understanding of draw mechanics relating to sublevel caving seems to be emerging. This work is certainly helpful to those of us interested in block caving but the question of "what goes on up above" still hounds us since we are more interested in the region of draw which begins just above the area where sublevel caving interest ends. Herein is presented a brief summary of draw theory with an attempt to look at the factors which can help our understanding of the area of draw influence in block caving mines. Nature of Gravity Flow An understanding of the flow of granular material (rock, sand, grain, or prill as examples) is the first step toward understanding block caving draw. If we take a supported column of granular material and allow gravity flow through an aperture at the bottom of the column, an ellipsoidal shaped zone of disturbance of the in-place material will form and grow with extraction of material through the aperture. The volume of this zone of disturbance or loosening is about 15 times the volume of material extracted at any given time (Kvapil, 1980). Figure 1 shows the development over time of the zone of disturbance. The ellipsoid of disturbance represents a future ellipsoid of extraction which will equate to the volume of materia1 extracted by that future time. Extraction involves the movement of the particles located vertically over the drawhole directly downward while material outside this direct vertical volume moves radially inward and down toward the drawpoint as shown in Figure 2a. Figure 2b shows the result of this motion on originally horizontal strata within the ore column. Increased draw increases the eccentricity of the ellipsoidal volume or, in other words, the ratio of the height over the width of the disturbed area increases as ore is withdrawn from the column (Kvapil , 1980). This becomes important to block caving since eventually a vertical cylinder of draw will be approximated as this ratio increases without bounds. Figure 3 shows this result. The width of this draw cylinder is a critical dimension for the determination of draw point spacing in relationship to block caving mine design. McCormick (1968) for one, felt that within this cylinder of draw, mass flow would take place. This is the

Jan 1, 1981

By Richard E. Lounsbury

Coal mine refuse handling traditionally has been the redheaded stepchild of the industry-a problem to be ignored as much as possible. During the past few years, however, mining companies have become more aware of the potential water pollution problem associated with refuse handling and storage. Planning for refuse disposal involves environmental protection and the economics of refuse handling. For over two years, Monterey Coal Co. has operated a non-polluting refuse disposal system at its No. 1 Mine located in Brushy Mound Township of Macoupin County 6 miles south of Carlinville, Illinois. Drainage goes to Spanish Needle Creek and eventually to the Illinois River. The mine produced 3.5 million tons of clean coal during its first two and one-half years of operation and is designed to produce 3 million tpy of clean coal at capacity.

Jan 6, 1973

C. Q. PAYNE, New York, N. Y. (written discussion*).-The method adopted by Mr. Lennox is a very interesting test of the practical application of Mr. Gates' crushing-surface diagram to a greet variety of gold and copper ores. His method of dealing with the material below 200-mesh is also a distinct contribution to the subject, although, as he suggests, it seems likely that some microscopic measurement of this material may be advisable before the mesh reciprocals of its group particles can be dealt with as accurately as can those coarser than 200-mesh. In examining the general results shown in Table 3, it is somewhat puzzling to perceive why Calumet &, Hecla jig tails should show a crushing resistance 3 - times greater than that of the ore from the Ray Consolidated copper mine. The latter is, I believe, an altered. Pinal schist

Jan 10, 1918

By S. A. Herres, A. R. Elsea

Temper brittleness refers to the loss in the notched-bar impact resistance encountered in most medium- or low-alloy steels when they are tempered within the temperature range of 700 to ll00°F or slowly cooled from a higher tempering temperature. Temper brittleness is important because it impairs the service properties of otherwise suitable steels over the range of hardnesses obtained at medium tempering temperatures and because it is impractical to cool pieces of large section rapidly enough from higher tempering temperatures to prevent temper brittleness. The problem of temper brittleness has always been closely associated with ordnance manufacture because armor plate and gun steels require good shock resistance and are often heat treated in heavy section. However, it is now realized that many brittle failures in structural alloy steel parts are attributable to temper brittleness, and there is little question that it contributes to the low impact resistance of alloy steels used in the hot-rolled or normalized condition which are slowly cooled from the hot-rolling or normalizing temperature. Recently Hollomonl has presented a comprehensive summary of the literature on the subject and an excellent description of the manner in which temper brittleness affects the notched-bar impact resistance and other mechanical properties of steel. Carpenter and Robertson2 have given a good analysis of the probable mechanism of temper brittleness, which is similar in many respects to the precipitation-hardening phenomenon. Fig 1 is their diagram illustrating the response to tempering of a susceptible steel. Three changes are recognized as the temperature of tempering a previously quenched steel is raised: (1) pre- cipitation occurs more rapidly and to a greater extent and the notched-bar impact value falls to a minimum; (2) coalescence of the precipitated particles begins to be effective and the impact values for both rapidly cooled and slowly cooled specimens increase; (3) the precipitate goes back into solution at higher tempering temperatures and the impact values of specimens cooled rapidly enough to retain the solution increase, while reprecipitation occurs in slowly cooled specimens and their impact values decrease again. No change must proceed to completion before the following one begins and there is overlapping in temperature ranges. Although there have been a large number of experimental investigations of temper brittleness, insufficient evidence has been accumulated to permit definite identification of the precipitate wnich causes temper brittleness nor have the specific effects on it of various alloy elements and impurities in steel been definitely established. This lack of evidence is largely a result of the lack of a suitable measure for temper brittleness. Temper brittleness is evidenced by an increase in the temperature of brittle failure of notched-bar impact specimens, but most of the data are in the form of an arbitrary susceptibility ratio of the room-temperature impact value for specimens quenched from a high tempering temper to that of similar specimens furnace cooled from the temper. It is obvious that this numerical ratio is dependent upon the type of specimen used and the specific conditions of testing rather than the characteristics of the steel. In general, manganese, chromium, and nickel alloy steels are most susceptible to temper brittleness and molybdenum has heen used to decrease

Jan 1, 1950

By R. A. Deju, R. B. Bhappu

Further information on the surface characteristics of the silicate minerals was obtained by experimentally correlating the oxygen-silicon ratio of the silicates with their electrokinetic properties. Specifically, the behavior of the minerals in an electric field was investigated using zero point of charge as a parameter. A modified electrophoresis cell was used for the determination of electrophoretic mobilities. It was shown that there is an increase in the zero point of charge with increasing oxygen-silicon ratio in the silicates. Finally, a chemical interpretation was presented to describe the surface phenomena observed in the experiments. In recent years great interest in surface chemistry has produced a number of methods to study the surfaces of minerals and to observe the phenomena occurring at their interfaces. One such method is discussed in this paper. A rather complete review of the surface characteristics of the oxide minerals has been undertaken by parks,' but, a similar study has not been made for the silicate minerals. Two previous papers by the authors2'3 attempted to remedy this situation. In these papers it was demonstrated that the reaction between the silicate mineral particles and acidic water involves mainly an exchange of metal ions for hydrogen ions on the surface of the solid, leading to an increase in pH of the aqueous phase. Also, the degree of reaction was found to depend on the oxygen-silicon ratio of the silicate structure, being least for the quartz and greatest for the olivines. A hypothesis was then set forth explaining that upon the fracturing of a silicate mineral, the oxygen-metal bond (which is almost entirely ionic in character) will break more easily than the stronger oxygen-silicon bond. This results in the exposure of unsatisfied oxygen sites on one hand and active, exchangeable cations on the other. These active sites on the fractured surfaces are then available for reaction with the hydrogen ions in acidified aqueous solution. Thus, an increase in degree of adsorption of hydrogen ions occurs as the oxygen-silicon ratio increases due to the presence of a larger number of active sites on such minerals. A correlation between oxygen-silicon ratio and electrokinetic properties will be further pursued in this paper from both the theoretical and experimental points of view. Efforts will then be made to present a chemical interpretation of surface phenomena observed in the experiments. It is believed that this study may supply pertinent information on the behavior of silicate minerals in froth flotation systems. ELECTROKINETIC STUDIES Equipment: In a previous paper,2 Deju and Bhappu described a simple method for determing the zero point of charge using a potential across a cata-phoresis cell and observing particle movement by means of a Rayoscope* optical system. This setup is simple in design and operation and extremely reliable. With care, reproducible results within 1.5% accuracy may be obtained. A new setup has been developed, based partly on the design by Zeta-Meter Corp.4 and partly on previous cells used at the New Mexico Bureau of Mines. This new, modified cell is shown in Fig. 1. Although

Jan 1, 1967

By H. T. Clark

NO previous determinations of the deformation or recrystallization textures of titanium or of titanium-base alloys have been reported in the literature. The room-temperature structure of titanium is hexagonal close-packed with a c/a ratio less than 1.633. It would be expected, therefore, to have a rolling texture similar to that of other hexagonal close-packed metals, namely (0001) [1010]. Burgers and Jacobs1 have shown that zirconium, a metal isomorphous with titanium in its structure and similar in many of its properties, has such a texture with a scatter of the basal plane toward the transverse direction. This scatter is in the opposite direction from that found in magnesium by Bakarian2 but similar to that reported by Smigelskas and Barrett3 or beryllium. The rolling and annealing textures reported here for high-purity iodide titanium are significantly different from the . textures of any other hexagonal close-packed metal. All titanium used during this investigation was prepared by the iodode process." The annealed hardness of this material varied from 73 (material used for sample No. 2) to 97 Vickers hardness number. An estimate of the chemical composition of this grade of titanium has been reported by Finlay and Snyder.5 With one exception, shown in table I, the as-deposited titanium was cast into 10 to 20 g ingots in an electric arc furnace in purified argon before being rolled to sheet. The cast ingots were forged and ground until their cross-section was approximately rectangular, annealed 1 hr at 700°C in vacuum and cold rolled. Rolling was carried out in a two-high, 4 in. diam mill, using reductions no greater than 10 pct per pass. The direction of rolling was reversed after each pass, and, in order to avoid temperature effects, the sheet was allowed to cool after each pass. Unless the rolled sheet was sufficiently thin for X-ray penetration (about 0.004 in.), it was reduced to this thickness by pickling. Because of the possibility of introducing twinning or other deformation during grinding, no attempt was made to maintain uniform thickness of the sample during pickling by intermediate grinding or sanding operations. Those samples to be used for determining the annealed texture were recrystallized by vacuum annealing the cold-rolled sheet for 1 hr at 500°C. These thin samples were held between thick titanium sheets during annealing to prevent distortion. Table I outlines the rolling and annealing schedule of those samples for which photograms or texture patterns are shown. X-ray Techniques The usual techniques for determining textures were employed during this work. Molybdenum radiation was used for the transmission exposures and copper radiation for the glancing angle ones. Since titanium fluoresces under these conditions, it is necessary to employ a filter between the sample and the film. The Kß radiation filters are very satisfactory for this purpose. Sufficient grains having favorable orientation were present in both the cold-worked and in the cold-worked—500°C annealed samples to provide satisfactory patterns with the samples stationary. Because of the difficulties of comparing intensities of transmission photograms with those obtained

Jan 1, 1951

By B. M. Larsen, T. E. Brower

For some years we have been carrying on a rather comprehensive investigation of the occurrence of oxygen in liquid open-hearth steel. This investigation was interrupted by the war emergency and is therefore incomplete, with many questions still answered only partially, if at all; yet it seemed worth while to present a report of progress on this difficult field of research, if for no other reason than to promote discussion and further investigation of this important problem. The significance of such studies depends in large measure upon the accuracy of measurements of oxygen content in liquid steel while it is still in the furnace or as it flows into the ladle, or thence into the mold and there is, as we shall show, good reason for believing that the main source of uncertainty is in the sampling, not in the analytical method as such. The difficulty arises from the fact that any method of sampling is of itself apt to alter the amount of oxygen in solution in the liquid steel, because this oxygen is in a readily reactive condition. On the one hand, being usually present at a concentration appreciably in excess of that corresponding to equilibrium with the carbon then present, it may decrease rapidly in percentage by reaction with carbon and evolution of CO, especially if the liquid metal is in any way shaken or brought in contact with a cooler solid surface. On the other hand, it may increase rapidly by ab- sorption of oxygen from a slag, a furnace atmosphere, or from air. These circumstances, which are inherent in the problem, as well as our conclusion that, despite the considerable amount of careful work already done, there is still no method of sampling liquid steel acceptable as an unquestioned standard, ed us to undertake systematic comparisons of oxygen content of large numbers of samples taken: (I) by a single method at different positions and levels in the bath; (2) at the same place by different sampling methods; and (3) from bath, tapping stream and pouring stream. The different sampling methods yield somewhat different values and there is as yet no way to tell with certainty which is the most accurate. But the general reproducibility and consistency of the results give us some confidence in certain inferences we draw from them: namely, that the "spoon" method of sampling, properly carried out, gives somewhat more consistent results than the "bomb" method, as it has usually been practiced; that, in the bomb method, an aluminum cap is preferable to a steel cap; that the oxygen content of liquid steel in a finished heat is substantially the same all over the bath at the same level, and tends to decrease at lower levels further from the slag interface; also that it tends to decrease, and to decrease erratically, from furnace bath to tapping stream entering the ladle. Accordingly it seemed desirable to report these observations in detail as a first step, so that the reader may judge their significance as a contribution towards solution of the main problem, which is to find a means of pre-2

Jan 1, 1945

By R. A. Swalin, B. W. Roberts

ONSIDERABLE controversy has centered about the existence of an order-disorder transformation in alloys in the composition vicinity of 75 atomic pct Ni and 25 atomic pct Cr. All the evidence to date for such a transformation is of a rather indirect nature, since direct X-ray confirmation is difficult to obtain as a result of the small difference in X-ray scattering factors between nickel and chromium. As a result, superlattice lines would be very faint if present. Several investigators1-5 have observed anomalies in the electrical resistivity vs temperature curves of alloys in the vicinity of 25 atomic pct Cr. The observed change is characterized by a rather broad resistivity peak at about 540°C. A discontinuous drop in resistivity is normally associated with ordering. However, Taylor and Hin-ton4 have rationalized that the discrepancy could conceivably be caused by changes in the Brillouin zones upon ordering. The same investigators measured the specific heat as a function of temperature and have also observed anomalies in the vicinity of 540°C. Nordheim and Grant5 have proposed, because of the absence of superlattice lines and the absence of a discontinuity in the resistivity vs temperature curve, that long-range order is improbable and that the results could be better explained by short-range ordering. To date, however, the question has not been resolved satisfactorily. Neutron diffraction techniques provide a method for partially resolving the question since nickel and chromium have considerably different atomic scattering factors in the case of neutrons and, therefore, superlattice peaks, if ordering occurs, should be readily discernable. The results of a neutron diffraction investigation* coupled with a dilatometric in- vestigation are reported here. An alloy containing 28.0 atomic pct Cr was prepared from carbonyl nickel and electrolytic chromium in the form of a 1-in. diam x 10-in. ingot. Melting was done in an alumina crucible and casting in a graphite mold. The ingot was homogenized at 1250°C for seven days, after which a 5-in. long piece was cut into shavings in order to obtain a suitable neutron diffraction sample. Hardness samples and samples suitable for dilatometric analysis (% in. diam x 2 in.) were prepared from the remainlng piece. The neutron diffraction sample, along with a hardness sample, was annealed at 501°C for seven days, at which time the temperature was lowered to 479°C and held at this temperature for twenty-four more days. The hardness was observed to increase from 133 to 147 Vhn during the course of the annealing treatment, in qualitative agreement with Nordheim and Grant." Neutron diffraction traces taken at room temperature and at 42 °K are shown in Fig. 1. The insert shows the trace taken at room temperature with short counting times and thus only fair statistical accuracy. No evidence for superstructure reflections of Cu3Au-type ordering is observed. The statistical accuracy of the 4.2°K trace was improved by using longer counting periods. Several weak intensities are observed at small angles, including an aluminum reflection from the cryostat assembly and a very

Jan 1, 1958

By W. R. Opie, O. W. Mole

By confining the electrolytic reduction of TiCl4 to the interior of a porous basket-cathode the electrolyte between the anode and the cathode can be kept free of reduced chlorides of titanium eliminating undesirable reactions of reduced titanium chlorides with brickwork or oxygen in the cell atmosphere. Semiwalls are not needed. Operating conditions are given and discussed. Titanium yields based on TiCl4 introduced are 93 pct. Cell voltage and amperage characteristics are adaptable to multiple cathode-series cell urmngements. EXPERIMENTS conducted in the National Lead Co., Titanium Division, Research Laboratories showed that titanium metal could be deposited in an electrolytic cell in which titanium tetrachloride was introduced through a tubular cathode.' The reduced chlorides as formed were confined to the vicinity of the cathode. They were reduced to form a cocoon-shaped growth of sponge titanium metal at the end of the cathodic tube below the surface of a sodium chloride-strontium chloride electrolyte. No diaphragm was needed.' Although high-purity, coarse crystalline metal was produced in the cocoon growth, the yields of metal removed from the cell, based on the amount of titanium introduced as TiCl4, were usually only 40 to 60 pct. The growth of the cocoon deposits was away from the cathodic tube for introduction of TiC14 toward the anode following the flu lines. The reduced chlorides of titanium diffused through the deposit and were reduced to titanium electrolytically within the deposit or on the outer surfaces. Deposition within the pores of the cocoon was detrimental to further deposition because it plugged the passages used by the reduced chlorides to diffuse away from the point of titanium introduction. As plugging due to deposition in the pores proceeded, the reduced chlorides in the center of the cocoon would force their way out by forming a channel and would escape from the vicinity of the cathode without being reduced to metal. Some work had been done previously1, 2 which indicated that if the end of the cathodic tube for introducing TiC14 was surrounded by a screen connected to the tube so that it too was cathodic, growth could be made to occur within the screen. Direction of growth was observed to be from the screen toward the point of TiCl4 introduction. Through a series of design modifications a cathode evolved which consisted of an introduction tube surrounded by a perforated metal basket as shown in Fig. 1. Modifications of this design are described in Refs. 3, 4, and 5. This basic cathode designa" was incorporated in electrolytic cells containing graphite anodes and constructed of high-silica brick refractory for containing the electrolyte (see Fig. 2). The inner crucible was surrounded by insulating brick and the entire unit contained in a welded steel shell. Suitable cooling chambers with inert gas atmospheres were devised so that the cathode could be removed from the cell without exposing the deposit to air while hot. Various alkali and alkaline earth chlorides were used as electrolytes.

Jan 1, 1961

By J. L. Huitt, B. B. McGlothlin, J. J. Day

Laboratory tests were made with pure minerals and actual reservoir rock samples to study the effects of hydrothermal (steam m hot water) treatments on reservoir rock properties. These tests showed that hydro-thermal treatment of many reservoir rocks can result in significant rock softening. The softening was attributed primarily to the partial destruction of dolomite and kaolinite and the synthesis of montmorillonite in the presence of excess silica. In many cases, the softening was great enough to cause considerable healing of propped fractures; therefore, a serious reduction in welt productivity could result. In other tests it was found that the addition of ammonia to a hydrothermal treating fluid in a concentration as low as 0.013 Ib/lb of water not only could prevent rock softening but could cause rock hardening. The results of X-ray diflraction analyses of rock samples showed that when ammonia was added to the treating fluid, ammonium-mica and analcite were formed instead of montmorillonite. No significant permeability damage was observed in the sandstones that were subjected to the ammonia-hydro-thermal environment; in some sandstones, permeabifity improvements resulted. INTRODUCTION As the use of steam or hot water becomes more prevalent in well stimulation methods. the need for information on the effects of such treatments on reservoir rock properties becomes increasingly apparent. Several works have been published on high-temperature changes in rock properties,',' but these are more applicable to in situ combustion operations than to steam or hot water injection processes. The mineralogical literature contains many publications which report on the changes occurring with various pure minerals in hydrothermal systems. A review of this literature denotes the ease with which entirely new, crystalline mineral phases can be synthesized from other minerals in hydrothermal environments at temperatures, pressures and residence times typical of those encountered in oilfield thermal recovery or stimulation processes. Discussions of many of these experiments are given by Deer et al. Grim,' Roy et al., Zen\ and Hawkins.' One of the most significant of these pure mineral studies is the hydrothermal synthesis work of Levinson and Vian" in which montmorillonite was synthesized from naturally occurring minerals; i.e., kaolinite, quartz and carbonate minerals (particularly dolomite). These reactions occurred at 575F in only 2 days and at 300F in 5 days. These results may be applicable to petroleum reservoir rocks since the minerals studied were those which are commonly found in sandstones. Furthermore, the environmental conditions imposed in the studies were very similar to those involved in thermal stimulation of petroleum reservoirs, e.g., steam or hot water injection. Other studies have suggested that weak rocks could be hardened by "electrochemical induration", a process in which an electric current is applied to a clay-containing rock body. These tests can be regarded as hydrothermal treatments since they were conducted in some instances with aqueous solutions and since clay temperatures during the electrical treatment reached a maximum of about 100C. Although a number of studies of the reaction of pure minerals have been reported, very little has been published on the reactions of petroleum rock-hydrothermal systems. No work has been reported on preventing the more detrimental rock changes in rock softening which might occur during the injection of steam or hot water into reservoirs. The studies described in this paper were conducted to provide such information. EXPERIMENTAL APPROACH The laboratory tests included studies of the effect of hydrothermal treatment on core samples from several different reservoirs. The hydrothermal treatments (simulated steam treatments) were conducted with distilled water at 575F, for the most part, for periods of 2 to 6 days. This temperature level was selected because it represented that temperature which would probably prevail in several cases under consideration for steam injection projects. The core samples, as well as the pure mineral samples, were contained in high-pressure stainless steel, autoclave-type pressure vessels. The effects of the hydrothermal treatments were evaluated by measuring the penetrometer hardness, formation rock embedment strength and permeabilities of the core samples before and after the treatments (Fig. 1)'" In addition, the mineralogical changes in the specimens were studied by X-ray diffraction. Concomitant with the core sample studies, the mineralogical changes were studied in greater detail by conducting hydrothermal synthesis experiments with pure minerals at similar temperature levels and residence times. For the most part, samples of finely-crushed pure dolomite.

By Ralph W. M. Lai, D. W. Fuerstenau

This paper presents the results of a study of the principles which control the distribution of ultrafine particles between an oil phase and an aqueous phase. Alkyl sulfonates were used to control the wettability of fine alumina particles and to stabilize the water-isooctane emulsion system in the extraction process. The effects of sulfonate chain length, sulfonate adsorption, pH, and oil-water ratio on the recovery of solids in the oil phase were investigated. Higher extraction was found under conditions which yield higher hydrophobicity and large interfacial area of the oil-water emulsion. Today there is considerable interest in developing methods for the recovery of fine particles from disseminated ores. One such method might be the extraction of fine particulate solids from aqueous suspensions into an oil phase, and one example of a successful industrial process based on oil-water distribution phenomena is the emulsion flotation process used in concentrating manganese ore.' The oil agglomeration process of Farnand, Smith, and Puddington has been suggested for concentrating tin ore. Patents 3-4 for oil flotation processes extend back to that of William Haynes in 1860. The basis of all these processes is directly related to the stabilization of emulsions with solid particles. The first extensive study of oil-water emulsions stabilized by finely divided solids was made by Pickering. Later, Briggs,6 weston, 7 Chessman and King,8 and Leja and Schulman9 experimentally demonstrated how solid particles control water-oil and oil-water systems. Hildebrand10 suggested that fine particles can stabilize an emulsion because the fine particles are partially wettable by both oil and water, that is, that the contact angle must be finite. Takakuwa and Takamori 11 recently applied emulsion inversion to the study of collector adsorption in flotation systems. At the Royal School of Mines, Shergold and Mellgren12 are currently carrying out a comprehensive study of the extraction of fine particles into an organic liquid phase. In the present study of the liquid extraction or oil flotation of ultrafine particles, the recovery of hydro-philic alumina particles of 0.1-µ average diameter was determined after separating an isooctane-water mixture (emulsion) into its two phases. Alkyl sulfonates of different chain lengths were used to change the wettability of the alumina and to effect emulsifi-cation of the oil-water mixture. The effects of the oil-water volume ratio, sulfonate adsorption, and pH on the recovery of the fine particles were investigated. Since the surface charge on an oxide such as alumina is determined by the adsorption or interaction of H+ and OH- with the surface, pH control is extremely important. Furthermore, since the zero point of charge (zpc) of alumina13-14 occurs at pH 9 to 9.4, major adsorption effects with anionic collectors in these systems will occur below pH 9. The results of the foregoing investigation are discussed in terms of the recovery of the fine particles, the oil-water ratio, contact angles, surface tension, the adsorption of sulfonate onto the solid surface, and the emulsifica-tion of oil. MATERIALS AND EXPERIMENTAL METHODS Materials: The particulate solid used in all the experiments was Linde "A" alumina, a high-purity, readily available form of a-alumina. The surface area of the alumina, as evaluated from measurements of stearic acid adsorption from benzene, was 14.5 sq m per gm, based on a value of 20.5 sq Å for the cross-sectional area of stearic acid.13 All aqueous solutions were prepared from triply distilled conductivity water. Other materials included high-purity crystals of sodium alkyl sulfonates, isooctane, and, for pH adjustments, reagent grade hydrochloric acid and sodium hydroxide-Because sulfonic acids are strong acids, they are

Jan 1, 1969

By Wayne E. Glenn

The San Miguelito Field of Ventura County, California, lies along the coast approximately five miles northwest of the city of Ventura. The structure is one of several in the Ventura anticline, a series of anticlinal folds trending northwest-southeast through the San Miguelito Field. The Ventura Avenue Field lies to the southeast along the anticline, and Padre Canyon and Rin-con Fields lie to the northwest; the series then extends beneath the Pacific Ocean. Production is obtained from the Lower Pico and Repetto formations of Pliocene age, and oil accumulation is controlled by faulting, lithology and structure. The first well in the First Grubb Pool was completed in November, 1931, and to date 48 producing wells have been drilled on the 276 productive acres. Approximately 685 ft of net pay are contained in the eight sand bodies grossing 1,220 ft of section. Production of oil to date has been 15,-600,000 bbl. A gas injection project was instigated in April, 1940, but was discontinued in September, 1949. This paper is confined to a discussion of the development and performance history of the First Grubb Pool of the San Miguelito Field. LOCATION AND GEOLOGY The San Miguelito Oil Field is located in Ventura County about five miles northwest of the city of Ventura along the coastal highway to Santa Barbara. It is located within sections 23, 24, 25, and 30 of Township 3 North, Range 24 West, San Bernardino Base and Meridian. Surface elevation in the field ranges from sea level to plus 1,200 ft, and the terrain is extremely rugged. The structure is well defined on the surface and on the wall of the Amphitheatre Canyon where appears a so-called "text book" anticlinal section. The San Miguelito structure is an asymmetrical, elongated anticline about two miles long and three-fourths of a mile wide. The trend of the axis of the anticline is northwest-southeast. Fig. 9 illustrates the contours and major faults of this structure. Dips on the southwesterly flank average about 40 degrees, whereas the northeasterly flank ranges from 60 to 75 degrees. There are several faults striking generally east and west. These faults do not appear to affect materially the area of accumulation or performance behavior. It is believed that accumulation was affected by steeply dipping beds and extremely low permeability of the northeast flank of the structure. As shown by the typical log, Fig. 1. the San Miguelito Field is divided into two stratigraphic producing intervals. The First Grubb Pool comprises the interval from the "G" to "L" markers; the Second Grubb Pool from the "L" to "M" markers. The First Grubb Pool, ranging in thickness from 1,105 to 1,680 ft, with an average of 1,220 ft, includes approximately 685 ft of oil-bearing sands. The First Grubb zone consists of eight sand intervals separated by shales. The shale bodies separating the eight sand intervals within the First Grubb Pool are continuous throughout the major part of the structure and serve as an effective barrier. Many of the thin, irregular shale or siltstone streaks within these sand bodies are discontinuous and do not affect well performance appreciably. The productive horizons in the First Grubb Pool are siltstones and sandstones of the Lower Pico and Repetto formations of Pliocene age. It is apparent from inspection of the typical log that the "G" to "L" interval might have been separated into at least six producing zones and selectively pro. duced. Unfortunately the electric log and some of our modern tools were not available or were in their infancy dur. ing the period 1931 through 1937. Not until 1937 when eight wells had been completed were there sufficient geological data to permit definition of the sand bodies. Then the problem of reservoir control in this multiple-sand field, where all sands are open to a common

Jan 1, 1950