Search Documents

By M. R. Geer, H. F. Yancey, P. S. Jacobsen

Two growing problems confront the preparation engineer—still further restrictions on stream pollution and a greater proportion of fine coal as more and more continuous miners come into use. The de-watering screens, centrifuges, and settling ponds that sufficed a few years ago must often be supplemented by more effective equipment, and in some instances the finest solids are now being recovered by vacuum filtration, once considered too costly in many coal washeries. Unfortunately not all slurries can be readily filtered. Some are virtually unfilter-able, and others do not permit the high cake rates needed to hold costs within reason. Often, however, these difficult slurries can be rendered filterable by flocculation. Starch and lime have long increased settling rate in thickeners and can also aid filtration. More recently there have been other flocculants, primarily synthetic polymers or gums. Reports of their great effectiveness prompted the U. S. Bureau of Mines to test their use in filtration as part of its program on recovering and cleaning fine coal. The object of the present work was to compare some of the newer flocculants with starch and lime and to test the reaction of different types of slurries to flocculation. Three natural slurries, three synthetic coal-clay mixtures, and five flocculants were tested, all with a laboratory filter leaf. Slurries and Flocculants Tested: First of the slurries was the thickener feed from the washed coal section of the Michel colliery of Crow's Nest Pass Co. Ltd., Michel, B.C. As shown by the screen and ash analyses in Table I, practically all this slurry was finer than 28 mesh, and about half the solids were finer than 200. Substantially all material coarser than 200 mesh was clean coal, but the ash content of 20.7 pct in the finest size indicates a moderate amount of impurity. This coal is medium-volatile bituminous in rank. Slurry was also obtained from the Black Diamond washery of Palmer Coking Coal Co., King County, Wash. This underflow of a 1/2-mm vibrating slurry screen is a waste product discharged to a settling pond. As shown by the data in Table I it contained about 20 pct material finer than 200 mesh, which analyzed 77.5 pct ash, indicating a high proportion of clay. The coarser sizes were also high in ash content because of the presence of bone and shale. Black Diamond coal is on the dividing line between bituminous and subbituminous rank. The third slurry, from the washery of Roslyn-Cascade Coal Co. in Kittitas County, Wash., was the underflow of a battery of 8-in. cyclones that is wasted with the coarser refuse from the plant. In both size and ash content this slurry was similar to the Black Diamond, but since it was a cyclone-underflow product, the fraction finer than 200 mesh undoubtedly contained a much smaller proportion of finely divided clay than was present in the Black Diamond slurry. The Roslyn-Cascade coal is high-volatile A bituminous in rank. Initially the slurry samples were stored in the laboratory at a concentration of 40 pct solids. A progressive change in filtration and flocculation characteristics during storage was noted, however, presumably because of progressive disintegration of the clay. After careful testing demonstrated that the slurry solids could be dried and then repulped without changing the original filtration characteristics, this procedure was adopted. The flocculants used were Separan 2610, Kylo 27, Jaguar MD-A, Idaho potato starch, and lime. The lime was used as a slurry, the Separan 2610 as a 0.10 pct aqueous solution, and the other flocculants as 0.50 pct aqueous solutions. The starch was causti-cized with sodium hydroxide before use. As some of the flocculants are reported to deteriorate on storage, new batches of flocculants were prepared every two days. Test Procedure: Fig. 1 diagrams the filter leaf apparatus employed. This consists of a test leaf having an effective area of 0.10 sq ft., a 60°, 8 1/2-in. diam cone to hold the slurry sample, a variable-speed electric stirrer, vacuum gage, bleed line for controlling vacuum, filtrate flask, moisture trap, and vacuum pump. Two filter cloths were selected—Saran SA 603, a monofilament, coarse-weave cloth, and polyethylene PO-801 HF, a monofilament, fine-weave cloth. The Saran was selected to provide maximum cake rate without regard to clarity of filtrate and the polyethylene to provide the best quality of filtrate without regard to cake rate. The test charge for the filtering vessel consisted of 800 g of solids (previously soaked for 24 hr) and

Jan 1, 1960

By R. L. Sebastian

ALUMINUM'S war history is the record of a successful race to expand facilities fast enough to meet the multiple increases in military requirements, principally for aircraft. From the beginning of the war program in 1940 through 1942, requirements estimates were repeatedly lifted to new high levels, and plans for increasing capacity had to be constantly revised. In 1943, basic metal supply caught up with and exceeded requirements, and by 1944, the surplus of primary production was large enough to force reduction in output and plant closings. In the past two years, ingot capacity has been ample, though periodic critical shortages have been experienced for a few fabricated shapes as a result of sudden shifts in demand. And now with all controls lifted we are faced with surplus capacity, surplus stocks, and surplus scrap. In 1938 the Aluminum Co. of America was the only U. S. producer of primary

Jan 1, 1946

By Paul E. Nilles

For every single BOF heat, the steelmaker must control the refining operation in order to satisfy at turndown the following conditions : - to reach the correct steel analysis (C, S, P, ...) in the shortest time possible, i.e. without reblow; - to maintain the temperature of the metal in a narrow range; - to produce the optimum steel weight. It is obvious that during refining limited time and scarce information are available and only very few corrective actions can be taken. For this reason, it is of the greatest importance to facilitate the control of the BOF process by taking adequate measures before and during charging of the converter. These are : - the availability of accurate and reliable equipments for the classical measurements, 5.e. weights, temperatures, flow-rates, analyses, etc... - the operation of an optimal charge calculation model which takes into account all information concerning the preceeding heats and the charged materials. '

Jan 1, 1972

By J. S. Ross

Few Canadians realize the role of their domestic industrial minerals industry because it is over-shadowed in production value by a large metallic minerals industry. But since 1960, Canada has had a reasonably well balanced, mature industrial minerals industry; and although the nation's sparsely scattered population has not been able to support an industrial minerals industry in a manner comparable to the domestic and foreign support given the metal mining sector, Canada is, nevertheless, exporting large quantities of higher priced nonmetallic minerals. Production of many of the basic minerals had been firmly established long before 1960, but it was not until the late 1950's that the output of cement, salt, titanium dioxide pigment and slag, sulfur, gypsum and sodium sulfate reached relatively high levels. Shortly after 1960, the significant potash and lithium chemicals industries were established and their effect is just now being realized.

Jan 11, 1964

By W. J. Keep

Those who have observed the influence of various elements upon cast-iron will be interested in the methods used by us to form the several series of test-bars, which form the basis of the conclusions presented in this paper. We found that we could not, by adding ordinary white stickphosphorus to molten iron, produce bars which would exhibit to the eye the peculiar influence of phosphorus. By melting wrought-iron drillings with red phosphorus, Mr. H. S. Fleming produced in his laboratory 10 pounds of phosphide of iron, containing 10.22 per cent. of phosphorus. With this we made two series of test-bars, the first with our white-base iron, and the second with our FLM gray-base iron. Before the time of making these bars we had been unable to procure regularly made pig-iron which contained enough phosphorus to permit of the production of

Jan 1, 1890

By H. E. N. Stone, B. L. Daniell

This paper examines the cracking behavior on chemical reduction of three types of ore/oxide briquette mixtures. The complex sintering/hardening atmosphere was replaced by 100% oxygen and the blast furnace atmosphere by a 5/95 hydrogedsteam mixture which was used isothermally at 700°C for a constant, arbitrary time. Cracking has been assessed by measurement of reduction expansion or increase in specimen diameter as a result of chemical reduction and a subjective index based on appearance and friability. Oxidized briquettes of iron ore concentrate crack on reduction'-3 in a manner which parallels the degradation of sinter in the Linder test. In the present work, the cracking behavior on chemical reduction of three types of ore/oxide briquette mixture has been studied. Firstly, LD converter fume with additions of silica; secondly, Oxfordshire ore with ferric oxide; thirdly, ferric oxide with separate additions of silica, alumina and lime. Motivation for the first-mentioned experiments lay in the improvement of the fume as furnace feed; for the second, in assessing the tolerance of a finely divided ferric oxide as a base for low melting point additions. The third series provided additional information. In this work, the complex sintering/hardening atmosphere is replaced by 100% oxygen and the blast furnace atmosphere is replaced by a 5/95 hydrogen/ steam mixture used isothermally at 700°C for a constant arbitrary time. The particular reduction conditions were known from previous experience3 to be capable of disclosing any tendency to cracking. Cracking has been assessed by measurement of reduction expansion (i.e., increases in specimen diameter as a result of chemical reduction) and a subjective index based on appearance and friability. Generally

Jan 1, 1970

By P. L. Allsman

Butte mining district contains extensive manganese vein deposits forming a peripheral zone. Oxidation in the veins studied usually extends to a depth of about 75 ft. Secondary minerals formed by oxidation were found to be ramsdellite—always accompanied by intermixed pyrolusite—and cryptomelane. Enrichment of the gossan is accomplished by reduction of weight upon oxidation; theoretical enrichment is 32.2 pct. Additional enrichment is caused by leaching of soluble minerals, particularly calcium and magnesium carbonates. BUTTE mining district contains extensive manganese vein deposits in the outer zone, surrounding the copper and zinc deposits and corresponding to the well known silver zone. This article describes the mineralogy of the manganese veins, the oxidation and enrichment processes, and the use of this information in prospecting. Information was derived from a study of the Emma, Star West, Tzarena, and Norwich mines, selected as representative of the district. Vein exposures at these mines were mapped, studied, and sampled on the outcrops and throughout the oxidized zone. Specimens were cut and polished for minera-graphic examination, identification, and textural studies. Knowledge of the manganese oxide minerals is scanty, previous information having been rendered obsolete by publication of the first correctly identified list of manganese oxide minerals by Fleischer and Richmond in 1943. Positive identification of the manganese oxides is possible only by X-ray analysis. Identifications for this study were made by the author with a Phillip's Diffractometer at the Montana School of Mines and confirmed by Lester Zeihen of The Anaconda Co., using a Norelco X-ray camera. It was necessiary to re-evaluate some X-ray data, as published patterns of several manganese oxides proved to be of mixtures, mostly showing pyrolusite as a contaminant. Perhaps the most useful information on oxidation and enrichment of manganese is presented in recent books by Goldschmidt1 and Rankama and Sahama.2 While their hypotheses are not conclusively proved, all laboratory and field evidence has served to substantiate them. This information was very useful in this study. Mineralogy: The primary minerals of the manganese veins are chiefly rhodochrosite and quartz. Rhodonite is abundant in the northern part of the district and in places has been found to comprise over a third of the vein matter. A variable but generally small amount of sulfides may be present, principally pyrite and silver minerals. Sphalerite is progressively more abundant near the zinc zone. Rhodochrosite is believed to form complete iso-morphous series with siderite, ankerite, and calcite. Some variation into these compositions is common, and the intermediate forms are termed manganosid-erite, manganankerite, and rnanganocalcite. Much of the rhodochrosite is remarkably pure. Other manganese minerals in the district include huebner-ite, alabandite, and helvite. Ramsdellite (MnO2, orthorhnmbic) is the principal manganese oxide mineral, comprising perhaps two-thirds of the total oxides. It is dull to iron black, and generally massive or platy in structure. A prominent platy cleavage is the only distinguishing megascopic characteristic. Pyrolusite (MnO2, tetragonal) is next most abundant to ramsdellite, with which it is usually intimately mixed. The luster is often brighter or more metallic than in ramsdellite, and needle-like crystals are diagnostic. Pyrolusite is common in small cavities formed by oxidation of pyrite grains. It is relatively abundant in zones of high limonite content. Cryptomelane (KMnO16 tetragonal ?) is rare in the outcrop, but becomes more abundant with depth. At depths of several hundred feet it is the principal oxide. Although its appearance varies, a blue-black flinty luster and blocky to conchoidal fracture are most common. A potassium flame test will identify this mineral. Hardness of all three oxides varies from 2 to 6. The three are quite commonly intermixed, and their textures can vary greatly. The commonest textures are massive or colloform, representative of colloidal deposition, or vuggy and boxwork textures, formed by partial leaching and oxidation in place. A box-work of either ramsdellite or chalcedony is formed after rhodochrosite rhombs and is indicative of ore shoots in this district. Some replacement of both quartz and the granitic wallrock by ramsdellite has been noted, but most of the oxide was deposited as a fissure filling by fine particles. No trace of manganite, hausmannite, braunite, or manganosite was found. No minerals of the psilome-lane group were detected besides cryptomelane. Amorphous MnO, was found at several spots. A specimen of oxide coated with yellow barite crystals was amorphous and not psilomelane (BaMn9O18. 2H2O). Voids formed by the leaching of sphalerite were coated with cryptomelane, not hetaerolite (ZnMn2O4) as might be expected. No manganese sulfate minerals were found in the gossans; however manganese alum (apjohnite ?) has been re-

Jan 1, 1957

By Bernard Moore

THE last few decades have witnessed the introduction of many new nonmetallic mineral products and changes in the use of many of those already well known. Among these is diatomite, formerly employed as a mild abrasive and, at one time, as the absorbent material in dynamite. Now nearly 100,000 tons a year are mined and milled into such things as filter aids, cement admixtures, insulants, fillers, absorbents, cosmetics, cleansers, etc. Pumice, commonly regarded as only an abrasive, is now also employed as an insulant, as light-weight aggregate and as a concrete admixture. With increasing use of insulants, light-weight aggregates, and acoustic stuccos and plasters in the building trades, both these mate-rials should find increased application. Very large deposits occur in eastern Oregon and have been studied by the U. S. Geological Survey in cooperation with the Oregon State Mining Board.

Jan 1, 1934

By John McCaslin

ONE of the most common technical terms in the U. S. today is automation-a word not listed in the 1946 dictionary. The influence of automation on the national economy has been tremendous. It has even been the subject of congressional investigations. Automation, writes Aronson, substitutes mechanical, hydraulic, pneumatic, electric, and electronic devices for human effort and decision? Automatic devices and instruments are used extensively in some industries, but many others have yet to take full advantage of these great discoveries. The petroleum industry has been a leader in using automatic controls-some refineries are almost completely controlled by automatic devices. The field of geophysics is entirely dependent on instruments and has progressed at almost exactly the same rate as improvements in instrumentation. In metallurgy and mineral dressing use of instrumentation is increasing very rapidly. Mining engineers throughout the country are beginning to think in terms of instruments and controls.

Jan 3, 1958

By H. O. Hofman, H. L. Norton

Zinc smelters in the central western States have established a very high standard of purity for blende-concentrates, viz., zinc 60, iron less than 3, and lead less than 1 per cent. The very low percentage of iron is made possible by the blende containing less than 0.5 per cent. of isomorphous iron sulphide and by the sparing occurrence of pyritic material in the large blende-deposits of southwestern Missouri and southeastern Kansas. The blende in these districts occurs in sub-carboniferous limestone, and is associated with chert, residual clay, cal-cite, pyrite or marcasite and bitumen. The different minerals are coarse and therefore readily separated by mechanical washing from the blende, with the exception of pyrite and marcasite, as blende has a specific gravity of from 3.9 to 4.1; marcasite, from 4.85 to 4.90; and pyrite, from 4.95 to 5.10. The common procedure of dressing the ores' is to crush in a breaker, size in a trommel with 0.5-in. holes, pass the over-size through roughing-rolls and then jig the ore, now reduced to 0.5 in. maximum size, in roughing multiple-sieve jigs. The products of these are waste-tailings, side-discharge coarse concentrates, side-discharge coarse middlings and bottom-discharge fine middlings. The coarse concentrates are sent to the market. The coarse middlings are crushed in middlings-rolls and brought back into the system by feeding into the main trommel. The fine middlings are cleaned upon finishing-jigs. Any pyrite or marcasite present follows the blende and increases the percent- +1MASSACHUSETTS INSTITUTE OF TECHNOLOGY, BOSTON, MASS.

Jan 1, 1905

By Ta M. Li

Application of an hydraulic mining system to a troublesome overburden removal project has unlocked an estimated three million tons of ore reserves at Caland Ore Co., Ltd.'s open-pit iron operation in Ontario, Canada. The mine, operated by Caland under a 99-year lease and royalty agreement with Steep Rock Iron Mines, Ltd., would have been forced to curtail its mining operations later this year as the economic limits of the original pit design were being reached. As a result of the stripping program, which uses a tandem set of Marconaflo jet slurry systems, Caland officials now estimate that mining will continue into 1977. These reserves, added to existing ore stockpiles, are expected to sustain the firm's pelletizing operation well into 1981. In addition, Caland engineers are initiating studies to continue mining since the ore body, to date, has yet to bottom out.

Jan 10, 1976

By Frank C. Frischknecht

Most early development and application of electromagnetic prospecting methods took place in Scandinavia, where geological conditions favor their use. In other parts of the world these methods have aroused cycles of interest, but in Scandinavia they have been used continuously and successfully since the 1920's. Electromagnetic methods may be classified into two general groups. One group includes methods in which the source of the electromagnetic field remains stationary while the receivers are moved about to explore the area. The other includes procedures in which the energizing and receiving systems are moved together. Other classifications could be based on the size of the energizing source, the particular components of the electromagnetic field which are measured, or the mode of trans- porting the equipment. The difference between fixed-source and moving-source methods, however, is of such great fundamental importance that it will be emphasized in this discussion.

Jan 9, 1959

By F. Louis Grammer

THE difference between blast-furnace gas and ordinary producer-gas is chiefly that blast-furnace gas is richer in CO, and poorer in hydrocarbons and hydrogen, as is shown in Table I. TABLE I.-Volume-Composition of Producer-Gas and Blast-Furnace Gas.. Producer-Gas. Blast-Furnace Gas. Per Cent. Per Cent. (Volume.) (Volume.) CO . 22 to 33 25.5 00., . 6 to 3 13.0 H . . 13 to 7 1.5 CH, 3 to 1.5 0.0 N . 54 to 60 60.0 If natural gas, water-gas, or by-product coke-oven gas be available, blast-furnace gas can be made to resemble very closely in calorific value the average producer-gas by merely mixing in one of these products, which are richer in hydro-carbons and, hydrogen. Blast-furnace gas, however, possesses a virtue which is sometimes absent in producer-gas, especially with coals very high in sulphur-namely, that blast-furnace gas is relatively free from sulphur. In some regions the sulphur in coal is an acute problem, and it is highly desirable to find uses for the products which are specially high in sulphur-content. An advantage would be gained if coal was coked before charging into the gas-producers, but this adds to the expense. Sulphur may be partly eliminated from coal by washing it, the success depending upon the form in which the sulphur occurs, and upon the efficiency of the washer, but it cannot always be removed to the extent desired at most American plants. It is not practicable to remove all the sulphur from producer-gas by washing it, though Mr. Reinhardt, of Germany,

Sep 1, 1908

By L. D. Lash

The key to successful liquid-liquid extraction is the solvent. First, and most important, it must be highly selective for the metal desired and yet reject other metal ions present; second, the ideal sol- vent is completely insoluble in the aqueous feed liquor; third, it has rapid phase separation and will not form emulsions; and, fourth, low cost is desirable, since losses occur even though the solvent is recycled. For this application a solvent known as DDPA (dodecyl phosphoric acid) was chosen since it closely met these requirements. DDPA is a long-chain alkyl phosphate developed for AEC by Oak Ridge National Laboratories, Dow Chemical Co., and the U. S. Bureau of Mines. The long chain contributes to low solubility in the aqueous phase and to high extracting power from acidic sulfate solutions, whereas the alkyl phosphates generally exhibit high selectivity for uranium solutions.

Jan 11, 1958

The Pennsylvania State College, Mineral Industries Experiment Station, State College, Pa For publications address the Director The Pennsylvania State College through the Minerals Research Experiment Station has issued 10 Bulletins and three Technical Papers, from which the following have been selected as of greatest interest to mining engineers and geologists: Bulletin 1, An investigation of the properties of smitliing coals (1922), free; 2, Petrography of the Mica Pendotite Dike at Dixonville (1926), free; 4, The Helderberg Group from cen¬tral Pennsylvania to southwestern Virginia (1929), 25 cents, 5, Bentonite in Pennsylvania (1929), 10 cents, 6, Production data on Appalachian oil fields (1930), free; 8, Oil field waters of Pennsyl¬vania (1930), free; Technical Paper 2, Condition of water in coals of various ranks.

Jan 1, 1933

By R. M. (Mike) Robb

Introduction The requirements to investigate a wide range of alternatives and analyze a variety of ‘what if’ questions make the automation of pit design a requirement in today’s rapidly changing mining industry. The wide-spread application of computers has relieved the engineer of much of the tedious and error-prone work related to mine design. He is thus free to do the creative and innovative thinking for which he is trained. It is now possible to investigate a large number of alternative pit designs in a reasonably short time period. In the past it was very easy for a team of engineers to consume 12 to 14 man-months in the detailed hand design of a large open pit. The pressure of today's mining industry, the desire to investigate a variety of alternative designs, and the shortage of qualified engineers make the slowness of hand design less preferred.

Jan 1, 1979

By E. A. Holbrook

AT the meeting of the Committee on Engineering A Education of the Institute at the New York meeting last February, it was brought out that the number of men graduating in mining engineering from our colleges at the present time is not sufficient to meet the ordinary needs of the mineral industries. Following the meeting, Samuel S. Wyer, consulting engineer of the Fuel-Power Transportation Educational Foundation of Columbus, Ohio, prepared a pamphlet called "Mining Engineering's Appeal to High School Seniors." Under the auspices of this Foundation the pamphlet is being sent to every high school in the United States. The pamphlet does not in any way paint glowing word pictures of the profession; rather it is a statement of the importance of mining engineering in our present-day civilization, together with the requirements in young men who are looking forward to an engineering career.

Jan 1, 1930

By Charles Sanford, William B. Schmidt, Eugene Moroni, John Murphy, Richard Bullock

An industry/government team sponsored by the Dept. of the Interior completed a study tour of the underground coal mining industries in Great Britain and Germany to review new and emerging coal mining technology. The group found that differences in tradition, mining conditions, and industry capabilities have led to different approaches in technological developments, many of which have the potential for application in U. S. mining. Both countries are working to improve materials and procedures for roadside pack wall. The British are developing a pump-packing system in which bentonite, water, stone, and a special cement are pipelined to the pack area to form a low strength compressible pack wall. The German industry is using anhydrite or blotzdammer to form a high strength pack wall. Both countries are using full-face tunnel-boring machines. The German industry has had considerable success with shield-type longwall supports.

Jan 1, 1977

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the period Oct. to Nov. 10, 1915: Lester S. Thompson, New York, N. Y. Arthur L. Sweetser, Boston, Mass. William Reed, El Oro, Mexico. Dorsey A. Lyon, Salt Lake City, Utah Heinrich Ries, Ithaca, N. Y. D. W. Blaylock has resigned his position with the St. Joseph Lead Co., Bonne Terre, Mo., and has accepted the position of division engineer for the Big Creek Coal Co., of Chicago, at Harrisburg, Ill. R. B. Lamb announces the removal of his office to Room 1809, 43 Exchange Place, New York, N. Y. C. C. Sanders has taken a bond and lease on the Red Mountain group of 34 mining claims (copper), Patagonia, Ariz., and has commenced extensive development.

Jan 12, 1915

By James W. Malcomson

The Tigre Mining Co. of Mexico, owned by the Lucky Tiger Combination Gold Mining Co. of Kansas City, decided early in 1910 to enlarge its mill, which consisted of a concentrator milling 3,000 tons of ore per month. The enlarged plant was designed to crush and concentrate 6,000 of ore and to cyanide 7,500 tons per month. The extra tonnage cyanided was to be obtained from tailings which were stored below the old mill. Power was supplied to the old mill from four boilers; a 150-h-p. Corliss engine and two Weber 60-h-p. gas-engines using producer-gas made from charcoal. The total horse-power required, including 60 h-p. used for machine-drills in the mine, was approximately 275. Cord-wood cost $4.32 per cord, 8 by 4 by 3 ft., and charcoal $15 per ton. The fuel supply in the surrounding country was approaching exhaustion; more than 150 mules and 50 men were engaged in cutting and transporting this fuel, and the unsettled political conditions in Sonora were such that it would be practically impossible to keep an organization of this kind together. The price of fuel was steadily rising and at times it became almost impossible to get sufficient fuel to operate. It was estimated that the enlarged plant, together with the mine, would require 750 h-p., as follows: Horse-Power. Old mill, which was left unchanged,..............180 New concentrator,.......................90 Cyanide-plant,........................380 Mine and other requirements,................. 100 Total,........•..................750 In a study of the best manner to obtain power the following alternative propositions were considered:

Jan 1, 1914