Search Documents

By O. B. Bennett

WHEN diamond drilling was introduced in the Rhokana mines in 1939 it was used principally for pillar removal and for completion of the upper portions of shrinkage stopes which were being affected by increasing pressure. This method of drilling long blastholes proved so successful that it was extended gradually to cover stoping, pillar recovery, and hanging cave work. By 1949 virtually all the production of Mindola and Nkana was being obtained by this method. At the present time 87,500 ft are drilled each month by the 80 diamond drills in daily operation. Responsibility for control and issue of diamond drilling equipment and crowns, as well as tabulation of all performance figures, was taken over by a specially formed Roto drill department, which also investigated the problems encountered with this new method. To assist this department a fully equipped test chamber, Fig. 1, was established underground where performances of various types of machines and equipment could be studied under conditions as nearly uniform as possible.

Jan 12, 1954

By A. S. Richardson

THE design of mine airways receives, in general, very little engineering treatment. To a large extent this is, of course, due to the fact that information upon which to base calculations is seldom available in definite form. In many mines the extent of the workable deposits may not be known at the time an air course is planned, and the length of service is indeterminable. Volume of air required for ventilation may also increase with extension of the life of a property, and natural obstacles, such as heavy ground, often place limitations upon the size of opening that can be maintained. Perhaps a majority of the shafts used in ventilation of metal mines were originally intended as hoisting shafts, and many of the tunnels and cross-cuts similarly used, were also designed as haulage ways or for other operating purposes. Even when a shaft is sunk solely for ventilation, custom usually dictates a size and shape consistent with the type commonly used for ordinary operations, because experience has demonstrated it can be excavated and maintained. In fact it may not be very far wrong to say most ventilation openings were never made with any consideration as to economic design for such use. When an air course is required to pass air between different parts of mine workings under a fixed pressure, the size of opening required for a given volume of flow, is, of course, determined by the resistance factor of the air course. It is then impossible to proportion the opening with reference to economics of power consumption, and this paper is limited to the design of openings where ventilation pressure or power consumption may be varied for economic advantage.

Jan 2, 1926

By B. M. Harra, F. G. McCutcheon, O&apos

Until about 1930, the universal practice of horizontal-retort zinc smelters in the United States, as far as the writers are aware, was to operate the retort furnaces on a 24-hr cycle; that is, the retorts were charged in the early morning of one day, and in the early morning of the following day the residues were cleaned out, the retorts recharged, and a new cycle started. During the business depression of the early thirties, zinc production fell off to the extent that zinc smelters had idle retort capacity. Rather than continue to run some of the retort furnaces on a 24-hr cycle and shut down the remainder, a few companies decided to try out a longer cycle. Although the output of zinc per retort per day is lower, the longer cycle permits a larger charge per retort and improved zinc recovery. Advantages of the longer cycle were soon evident, and the practice spread rapidly. Various lengths of cycle were used, typical examples being 28-hr, 32-hr, 36-hr, and 48-hr. The 48-hr cycle fits in best with the standard routine of smelter practice that was built up on the basis of the 24-hr cycle; that is, the retort furnace "maneuver" always comes at the same time of day, and can be performed in the cool hours of the early morning. Under some conditions, particularly in some of the older plants, where the retorts are smaller than in newer plants, a 48-hr cycle is longer than necessary, and some intermediate length of cycle may theoretically be most economical. Use of an intermediate cycle, however, means that the maneuver comes at different times on consecutive days, and that sometimes it comes during the hottest part of the day. The work on the retort furnaces is extremely hot and arduous at best, and it is much worse, of course, if it is done during the heat of a summer day. When labor was plentiful and tractable, many plants were able to operate on cycles of intermediate length, but the workmen did not like the working hours. Under present labor conditions, it is hardly practicable to operate with a cycle of intermediate length, so the choice has narrowed down to the alternatives of 24-hr or 48-hr cycles. In any discussion of economics, too comprehensive generalization is not warranted, because local conditions affecting economics vary greatly. The best economic practice at one plant at any given time may be uneconomical at another plant, or even at the same plant at another time. To determine the length of cycle that is the better practice at a given plant at a given time requires a weighing of the advantages and disadvantages of each cycle, taking into consideration all the local conditions. some of the factors that must be considered in making the comparison are discussed briefly in the following paragraphs.

Jan 1, 1949

By J. L. Leland Myer

Some of the early experiments on the oxidation temperature of coal1 were undertaken in England in connection with a study of self-heating, or spontaneous combustion. It was then suspected that coals with low oxidation temperature were most likely to ignite by self-heating, but further experiments showed that many additional factors were involved. The oxidation temperature has importance as a physical property or characteristic of the coal. While only a few of the physical properties have been studied, they appear to have basic significance2 in the ultimate classification of all coals. When reliable data become available on the oxidation temperatures, as determined by standard and adequate methods, it should provide an additional basis for classification and comparative evaluation. Oxidation Temperature Defined For such a heterogeneous substance as coal is known to be, no simple definition of oxidation temperature can be established on a theoretical basis. If coals were homogeneous and of simpler structure, the accepted definition of "ignition temperature " as applied to simple gaseous mixtures might be adopted; that is, the temperature at which self-heating of the mixture sets in. But most coals self-heat slightly even at storage temperature, as evidenced by spontaneous combustion, and the definition for gases cannot be applied to coals with any exactness. By subjecting coals to suitable experimental conditions various oxidation characteristics can be obtained and examined for critical or significant stages of the oxidation process. Oxidation temperature itself must then be defined on the basis of such experimental results. Experimental Methods Attempts to determine critical points in the temperature functions of coal undergoing oxidation have resulted in the following experimental methods:

Jan 1, 1932

By F. H. Newell

At the Glen Summit meeting of the Institute, held in October, 1891, the writer presented a paper on the results of stream-measurements of the United States Geological Survey, reviewing briefly the data obtained at that time.* Since then the investigations have been steadily continued and enlarged, so that at the present time about 150 river-stations are main-

Jan 1, 1898

By Oswald J. Heinrich

At the Baltimore meeting of the Institute in February, 1879, Mr. Eckley B. Coxe, then president of the Institute, called attention in his address to the subject of Secondary Technical Education, and

Jan 1, 1881

By D. C. Seidel, E. F. Fitzhugh

Nickel sulfide ores lend themselves readily to concentration before smelting or pressure leaching, but neither of the major oxidized ore types-the iron-rich laterites and magnesium-rich, soft silicates-has been directly concentrated. Upgrading of crude ore in current practice is limited to cobbing lumps of the harder, lower grade rock (protore) from the softer, enriched silicate ore, because only a small percentage of the nickel in these ores occurs in discrete, contrasting mineral particles. There is no apparent mineralogical contrast in the superficial, iron-rich lateritic ores and, in fact, there is no firm assurance that the nickel atoms are within the lattices of the limonite minerals, or else irregularly adsorbed on the limonite. Within underlying, "rotten rock" silicates, occasional veinlets of garnierite and related nickeliferous silicates are found.1 The garnierite veinlets are only incidental, and the majority of the nickel atoms occur as erratic replacements of magnesium atoms in the micaceous chlorites of the ore mass.

Jan 4, 1968

By Robert E. Green, Edmund G. Henneke

The velocities of the three possible modes of elastic wave propagation have been calculated for single-crystal copper at 1-deg intervals throughout the standard stereographic triangle. The results are presented as isospeed contours. The deviations between the direction of maximum energy flux and specimen axes are presented as arrows drawn on stereographic projections. The orientation factors associated with dislocation motion on the primary slip system only and also on all twelve slip systems have been calculated for all three elastic waves. The orientation factors associated with a longitudinal standing wave resonant specimen have also been calculated. The results of these calculatians are compared with earlier calculations on aluminum crystals and the relevance of these results to ultrasonic attenuation measurements is discussed. GREEN and inton' have recently outlined a procedure for determining the orientation factors for dislocation damping in single crystals. The stress field associated with a given mode of elastic wave propagation is resolved on the slip systems in which it is assumed the dislocations are vibrating due to this stress field. Since, at room temperature, slip has been observed on a limited number of systems in fcc and hcp metal crystals, it is assumed that these systems are the appropriate ones to use for the resolving process. This procedure has been applied to aluminum crystals by Hinton and hreen' and to zinc crystals by Henneke and Green.3 In the present paper the modes of elastic wave propagation have been calculated for copper crystals possessing orientations at 1-deg intervals throughout the standard stereographic triangle. The deviation of the energy flux vectors from the specimen axis have been calculated for each mode. The stress field associated with each mode has been resolved on the (111)(110) slip systems in order to determine the orientation factors for dislocation damping. MODES OF ELASTIC WAVE PROPAGATION For any direction in a linear homogeneous aniso-tropic material three elastic modes can be propagated. In general, each of these modes has both longitudinal and transverse particle displacements associated with it and thus are not "pure" modes. However, there is always one component which is greatest in either a longitudinal or transverse direction and hence the mode may be referred to as quasi-longitudinal or quasi-transverse, accordingly. For certain axes of high symmetry pure modes may be propagated. The phenomenon of refraction of the energy flux vector is also exhibited by elastic wave propagation in ani-

Jan 1, 1969

By S. T. Yuster

An analysis has been made of the factors responsible for tilted fluid contacts in petroleum reservoirs. The factors are static and dynamic with the former being controlled by those variables responsible for the capillary rise of fluids, and the latter include rate of formation tilt and hydraulic circulation. The explanation that rate of formation tilt may be responsible for tilted contacts appears untenable. The role of some of these factors in the migration, fractionation. accumulation and possibly the prospecting for oil is indicated. INTRODUCTION While it is generally considered that the segregation of gas, oil, and water in a petroleum reservoir results in approximately horizontal planes separating these phases. there are factor; which modify this simplified picture to a very great extent. Some of these factors are static. and the departure of the fluid interfaces from horizontal may represent a static equlibriun. Some of these factors may be dynamic and the interface positions may be non-equilibrium and represent a steady .state condition. Of course combinations of these two situations may also exist. The reasons most commonly given for this behavior are hydraulic circulation of fluids, change in character of the formation, and a rate of tilt of the formations more rapid than the rate at which the fluids may re-establish an equilibrium. Russell's Principles of Petroleum Geology' contains an extensive discussion of tilted fluid interfaces and their importance in the migration and accumulation of petroleum. Russell cites examples of tilted water tables at Lance Creek, Wyo.; Rock River, Wyo.: Cut Bank. Mont.; Cushing, Okla.: and Graham; Okla. Also given was the Wasson Field of West Texas which has saucer shaped oil-water and gas-oil interfaces with the saucer being deeper in the case of the oil-water contact. The Bradford Field in Pennsylvania has a tilted water table. San Ardo. Coalinga None and some other California field.; have tilled contacts. A recent paper by King Hubbert discuses the effect of hydraulic circulation of the water underlying the oil in a given stratun and it- implications in the accumulation of and drilling for the oil. The foregoing would indicate that tilted fluid interfaces are not uncommon and that it would be of importance to underbtand the forces which are responsible. Further. it would be of interest to examine certain idealized models of situations which may cause tilting with the thought in mind of deriving relatinnships between the important variables. These relationships may only hold exactly for the model* assumed but the results may apply semi-quantitatively to actual formations and at least indicate trends. The discussion will be divided into the effect of static factors and the effect of dynamic factors. STATIC FACTORS It has already been mentioned that one reason given for tilted contacts is a variation in formation properties. Specifically this is a change in the pore size of the formation capilaries. If the internal surface of the reservoir is preferetially wet by water, capillarity will cause the water 10 rise to a greater extent above the free water table in a small capillary than in a large one. Consequently the water-oil contact will be higher in the lower permeability sands than in the higher permeability sand.;. The free water table may be defined as the position the oil-water interface would take if capillarity were absent. Since the phenomenon is the capillary rise of water in an oil environment, a derivation of this shold give a relationship between the variables. Fig. 1 is an idealized model of the situation with a uniform bore circular capillary ubstitttting for the tortuous non.circular formation pore. The upward force.; on the column of water will be equated to the forces downward to give the equilibrium situation. forces upward = force downward where r is the radius of the capillary in ceritimetera. a is the interfacial ten4on oil-water in dynes per centimeter, 0 is the

Jan 1, 1953

By Gregg A. Scott

Upper Stillwater Dam is to be a roller-compacted concrete gravity structure, founded on nearly horizontally bedded sandstone and argillite rock. An overview of the testing and analyses used to evaluate the adequacy of the foundation relative to deformation, seepage, and stability is presented.

Jan 1, 1984

Jan 1, 1935

By S. P. Singh, V. J. Hucka

There are a number of problems associated with underground coal mining, but the most serious and important are often related to the ground control. The influence of the prevailing geological conditions and features on the stability of underground mining has been outlined in this paper. Special emphasis has been given to the importance of geological techniques in the evaluation of coal mine roof conpetency prior to and during the mining operations. In addition to this, typi- cal ground control problems owing to the geological abnormalities have been depicted by appropriate case histories from coal seams in the State of Utah. The interdependence between longwall design and road- way stability on the one hand and geologic features on the other hand are shown in this study.

Jan 1, 1983

By Dermot Macaragh Ross-Brown, Brian Stimpson

Borehole information is often the only source of information on rock conditions at depth during the stage of feasibility studies of a project, and from this data the rock mechanics engineer would like to make some quantitative estimates of rock mass cohesive strength. While judgement and experience will usually play a paramount role at this stage, simple tools for estimating rock mass cohesive strength would be an asset. In this paper, an approximate technique is suggested for assessing the cohesive strength of a randomly jointed rock mass from borehole data on fracture intensity and intact rock strength.

Jan 1, 1980

By Walter M. Stephen

Modern developments in alloy steels have been so rapid and diverse that engineering practice has scarcely had time to re-appraise all items of past experience wherein conclusions became axiomatic under conditions that no longer apply. A case in point is the wet screening of abrasive ores within the fine range still looked upon as belonging exclusively to classifiers. By virtue of the development of stainless steels (18 per cent Cr, 8 per cent Ni), it is no longer true that classifiers are more economical than screens in closed circuit with large-tonnage ball or rod mills at 65 or even 100 mesh, provided a selective overgrind of the higher-gravity constituents of the ore is not desired. Wet screening of ores is a highly corrosive as well as an abrasive operation, because of the inevitably high degree of oxygenation of the water. Screen cloth of ordinary or spring-steel wire almost at once becomes pitted and covered with a film of corrosion products, which causes rust-blinding of fine-mesh screens and offers high frictional impedance to the flow of ore particles. On the other hand, the well-known properties of stainless steel enable it to maintain a bright surface, and so to eliminate blinding either by ore particles or by corrosion products. That a large-tonnage mill grinding hard ore to 65 mesh can be operated economically in closed circuit with screens instead of classifiers has recently been demonstrated at the Copper Cliff concentrator of the International Nickel Co.; in the test to be described, a 6½ by 12½-ft. Marcy rod mill ground from 625 to 820 tons of ore per day to approximately 65 mesh, operating in closed circuit with three 4 by 5-ft. Hum-mer screens, without any classifier. Stainless-steel cloth gave an indicated life of several months. There was no difficulty with blinding, yet dilution and spray water could be controlled so that screen undersize averaged not less than 40 per cent solids. In contrast, ordinary carbon steel was pitted and blind with rust within 40 hours.

Jan 1, 1939

By Walter M. Stephen

Modern developments in alloy steels have been so rapid and diverse that engineering practice has scarcely had time to re-appraise all items of past experience wherein conclusions became axiomatic under conditions that no longer apply. A case in point is the wet screening of abrasive ores within the fine range still looked upon as belonging exclusively to classifiers. By virtue of the development of stainless steels (18 per cent Cr, 8 per cent Ni), it is no longer true that classifiers are more economical than screens in closed circuit with large-tonnage ball or rod mills at 65 or even 100 mesh, provided a selective overgrind of the higher-gravity constituents of the ore is not desired. Wet screening of ores is a highly corrosive as well as an abrasive operation, because of the inevitably high degree of oxygenation of the water. Screen cloth of ordinary or spring-steel wire almost at once becomes pitted and covered with a film of corrosion products, which causes rust-blinding of fine-mesh screens and offers high frictional impedance to the flow of ore particles. On the other hand, the well-known properties of stainless steel enable it to maintain a bright surface, and so to eliminate blinding either by ore particles or by corrosion products. That a large-tonnage mill grinding hard ore to 65 mesh can be operated economically in closed circuit with screens instead of classifiers has recently been demonstrated at the Copper Cliff concentrator of the International Nickel Co.; in the test to be described, a 6½ by 12½-ft. Marcy rod mill ground from 625 to 820 tons of ore per day to approximately 65 mesh, operating in closed circuit with three 4 by 5-ft. Hum-mer screens, without any classifier. Stainless-steel cloth gave an indicated life of several months. There was no difficulty with blinding, yet dilution and spray water could be controlled so that screen undersize averaged not less than 40 per cent solids. In contrast, ordinary carbon steel was pitted and blind with rust within 40 hours.

Jan 1, 1939

By R. W. Marrs

Kimberlite contains a unique assemblage of minerals and exhibits a characteristic pattern of spectral reflectance in the visible and near-infrared wavelength region. This spectral pattern is readily discerned in well exposed kimberlite outcrops, but becomes increasingly difficult to identify when outcrops are partially covered by vegetation or soils derived from nonkimberlitic materials. Detection of poorly exposed kimberlite diatremes is possible using multispectral imaging techniques where spectral bands are chosen to optimize contrast between the kimberlitic soils, nonkimberlitic soils, and vegetation. Careful processing of the multispectral data is essential to separate the spectral signature of kimberlite from the signatures of other components of the scene.

Jan 1, 1986

By Henry N. McCarl, John J. Dran

In recent years, market rates of interest have risen well above their historical long-term average. Also during this period, the short-term variability of interest rates has been greater than in prior years. Interest rates have a significant effect on the operation of our economy. They influence the extractive industries in a number of ways. Their major long-range impact is on in- vestment decisions-specifically the valuation of mineral deposits. An understanding of the factors that influence interest rates is important to the engineer or businessman who makes the investment decisions for the mining company. The effect of changes in the market rate of interest on the value of mineral reserves is critical to the future financial success of the mining enterprise.

Jan 6, 1977

By I. A. Violic, L. D. Cruz, M. A. Solari

In Exxon's Los Bronces Expansion Project in Chile, a stochastic simulation is performed to resolve the complex decision problem of matching the mine to mill system capacities from both technical and economic standpoints. The unique combination of weather conditions at the mine and the 30-km (18.6 mile) belt conveyor network for ore transport to the mill necessitates this analysis in the planning phase to optimize the design capacity of the system. Appropriate statistical distributions of major equipment performance, snow storm duration, power outage, etc., are developed from actual mine local records and manufacturers' specifications. The interactions of operational constraints including ore storage capacities, number and sizes of individual equipment, ore variations, and mine and mill production rates are studied more realistically than in a traditional planning approach. Details of the computer modeling and typical results of simulation studies are discussed.

Jan 1, 1984

By P. W. George

THE rapid increase in cost of discovering new orebodies by churn drilling in the Tri-State district has led to some attempts to lessen the expense by using geophysical methods. Electrical prospecting was tried three or four years ago, but no successful results were recorded. In 1926, the Federal Mining and Smelting Co. engaged the North American Exploration Co., of Houston, Texas, to make some tests with the torsion balance. At first, it was thought that the most favorable conditions for discovery of ore deposits with the torsion balance would be in locations where the ore was known to occur at rather shallow depths, FIG. 1.-CROSS-SECTION OF DUENWEG LEASE. therefore the first trial was made at Duenweg, east of Joplin, where some zinc ore had been developed at a depth of 130 ft. The gravity gradients at 61 stations on a tract of about seventeen acres indicated plainly one large zone of maximum gravity and a smaller narrow zone of minimum gravity. Fourteen churn-drill holes, half of which struck ore, show that all the ore found was located outside the zones of maximum and minimum gravity. In the zone of maximum gravity the limestone beds were closest to the surface, and the first chert beds encountered were at the greatest depth. The results (shown in Table 1) indicated that the gravity of the limestone was greater than the gravity of the fractured chert together with its orebodies, and probably also greater than the bouldery soil and clay on top of the limestone. A cross-section of the Duenweg lease is shown in Fig. 1.

Jan 1, 1928

By H. C. Otis

During the past year or two considerable time and money have been spent in developing equipment for tubing large-volume high-pressure oil and gas wells without loss of production. That the efforts have met with success is proved by the fact that any properly cased well, regardless of its production or regardless of its rock pressure or working pressure, can now be safely tubed with no appreciable loss of production, provided experienced crews handle the new equipment. It is conceded that a far better gas-oil ratio can be secured by flowing a well through tubing of a proper diameter—the diameter of the tubing depending, of course, upon the volume of fluid and gas and the depth of the well—than by the more usual method of installing a choke at the mouth of the well. Where possible it is becoming the practice to bring wells in through tubing, though in the majority of instances this is not feasible. In many instances it has developed, after a well has been brought in through tubing, that the tubing installed is either too large or too small for the most efficient operation or that the well had not been drilled deep enough. The equipment described in this paper, in the hands of experienced men, permits the tubing of these wells after they have been brought in, with the size of tubing then determined by actual observation to be best suited for each particular well, and with no danger of the well getting out of control, of catching fire, of drilling itself deeper, or of any loss of production. The deeper the flowing production with the consequent future higher lifting costs, the more essential it is that the size of tubing used be such as to give the best possible gas-oil ratio. The ability to bring in these deep wells through the casing and then, immediately after their completion, regardless of volume or pressure, to tube them with the size of tubing that permits the most efficient use of the gas present will doubtless save many dollars. Uses for the New Equipment The equipment permits a further step in the operation of wells where the conservation of gas is of major importance. Perhaps 3-in. tubing

Jan 1, 1930