Search Documents

By Jan M. Mutmansky

A knowledge of rock characteristics forms the foundation for the application of rock mechanics to engineering works. Hence, there has been an increased interest in the determination and proper utilization of rock properties data. Most numerical values quoted for rock properties are obtained from arbitrary tests and are not necessarily indicative of any intrinsic rock characteristics. Recent attempts to correlate these properties by statistical methods have attracted considerable attention, in the hope that these might give some clue to the fundamental properties. To date, correlation and regression techniques have been employed for this purpose. The use of statistics has also been deemed appropriate because of inhomogeneity and anisotropy in rocks. The problems have been further compounded by the lack of standardized methods of measuring rock properties. The various ASTM committees are still deliberating on these matters, but recommendations should be forthcoming in the near future. As more reliable data become available, the ability of geoscientists to find more meaningful relationships between rock properties will be greatly enhanced. The objective of this paper is to outline another statistical technique which might be useful in providing an insight into the relationships that exist between rock properties. This method does not attempt to predict rock characteristics, but rather compares the similarity or dissimilarity between properties. This enables rock properties to be classified into groups with similar intrinsic characteristics. The technique described is one form of factor analysis. It allows the results obtained to be depicted geometrically, so as to make ready visual examination possible.

Jan 1, 1968

By Luis E. Vallejo

Experimental and theoretical analyses are presented to study the mechanics of growth and interaction for three inclined left-stepping, three inclined right-stepping and two inclined non-stepping cracks in a brittle material subjected to uniaxial compression. It was found that the non-stepping cracks did not interact and they propagated individually in a direction parallel to the uniaxial compressive stress. The propagating cracks formed in regions where tensile stresses developed. The left-stepping cracks interacted and formed branching cracks as a result of failure in tension of the material between them. Also, they propagated from their tips in a direction parallel to the uniaxial compressive stress. The right stepping cracks did not interact, but extended themselves from their tips following a direction parallel to the uniaxial compressive stress. The extended cracks formed in areas of compressive stresses.

Jan 1, 1984

By R. C. Gifkins

The ideas expressed in this paper interest me very greatly, partly for their own sake and partly because they are very close to some speculation I have recently made concerning grain boundary diffusion. This is in a paper describing an extension to Mott's "island" theory of the grain boundary, to be published shortly.37 The facets or islands of good fit are identified in terms of specific crystallography, as in the model put forward by Brandon et al., and the bad fit between them is suggested to be interlinked "channels" of relaxed vacancies, associated with grain boundary ledges.

Jan 1, 1969

By H. M. Howe, W. E. C. Eustis

THE processes which form the Subject of this paper have been experimented on in the laboratory of W. E. C. Eustis, but have not passed beyond the experimental stage. The first is the invention of Mr. J. L. Thomson, of Capelton, Quebec, Canada, the others have been invented by the writers. THOMSON'S PROCESS FOR THE EXTRACTION OF NICKEL This consists essentially in first rendering the nickel magnetic, and then separating it from the materials. with which it is mechanically

Jan 1, 1882

By Charles Macdonald

It may seem to be almost unnecessary to occupy the time of the Institute in further consideration of a question which has been so comprehensively treated in papers already on file in our own Transactions and in those of the American Society of Civil Engineers. Unfortunately, however, the results of these concerted efforts have not been materially to increase our stock of Knowledge in the direction sought for; and as the necessity for this information is becoming.more and more apparent as the demand for structural materials increases, it is believed that by continuing the agitation by means of discussions in this and kindred societies, whose members are vitally interested in obtaining reliable data as to the properties of the materials they are called upon to work with, public opinion may be educated up to the importance of exerting such an influence upon the law-makers of the country as will result in the formation of a competent board, with adequate means at its disposal, to carry out this great work in a manner alike acceptable to the makers and users of the materials in question. It may be proper in the first place to glance briefly at what has been attempted thus hr, then to indicate some of the more important lines of needed investigation, and finally to consider reasons why government aid may with propriety be sought for in carrying on the work. At a convention of the Society of Civil Engineers held at Chicago June 5th, 1872, it was, on motion of General William Sooy Smith, resolved, that, " Whereas, American engineers are now mainly dependent upon formula for the calculation of strength of the different form of iron and steel, not based on experiments upon American materials and manufacture; and " Whereas, There differ greatly in many of their ch~racteristics front thoae of foreign production, both in their nature and forma: therefore,

Jan 1, 1882

By James A. Burns

The challenge to designers of bulk materials handling systems is to apply the existing technology in areas where it has not been used and to foster better, cheaper and safer job performance. The Dashaveyor Co., a subsidiary of The Bendix Corp., built and tested a pilot system at Copper Range's White Pine mine. Based upon this success, a prototype system development was begun in 1967 to test the concepts in a full-scale, realistic environment.

Jan 11, 1973

By John M. Dealy, Robert D. Pehlke

This note presents a summary of the available literature on activity coefficients at infinite dilution in binary metallic solutions, Table I. These data should prove useful in not only examining the therm-odynamic properties of binary metallic solutions, but also in predicting the activity of a component in a complex alloy. The relationship proposed by wagner1 for expressing the activity coefficient in dilute solution is of the form:

Jan 1, 1963

By Guang Ping Cui

In this paper the imminent relationship between rock burst and its phenomenon with normal rock pressure and its appearance, as well as the factors of one changing into another have been analyzed. Based on this, the necessary and sufficient appearing factors of rock bursts have been put forward, and the term ''burst pressure" has been defined. According to the statistics data of tremendous rock bursts which appear in collieries in Hunan Province, the features of high frequency, great strength and shallow depth of the beginning burst have been found. There are some special structures in the coal seams, which are closely related with the burst phenomenon. A hypothesis of "star structure" has been suggested for the appearing mechanism of bursts. Inside and around this star structure the distribution rule of burst pressure and rock strength has been researched depending upon the theory of the limited stress field. A new description of the appearing causes of bursts has been raised.

Jan 1, 1984

By Frank Firmstone, Kenneth Robertson

Peculiar crusts having appeared on certain irons made at Glendon and Pequest, which, in our experience, were entirely new, some analyses of them were made; and these analyses, together with an account of the manner of appearance of the crusts, are herewith submitted to the Institute. At Pequest the ores mere: & Peters, from Ringwood, N. J.; + roasted sulphurous ore, from Charlotteburgh, N. J.; and + red ore (decomposed magnetite), from Chester, N. J. The fuel was 7/8 Lehigh anthracite and + Connellsville coke, and the limestone a dolomite from Andover, N. J. The resulting iron varied in silicon from 0 84 per cent. in No. 1 foundry to 0.51 per cent. in gray forge; in phosphorus, from 0.81 per cent. to 0.55 per cent.; sulphur, 0.035 per cent.; manganese, 0.375 per cent. It was highly "chilling" in its properties, and very strong. In running, it invariably appeared to be of a lower grade than it really was; the higher grades scintillating as much as hard iron usually does. After getting into the moulds, and beginning to cool, a black crust began to show itself, seeming to exude from the pigs, till finally, when the iron was cold enough to break, it completely covered the face of the pigs. At this time it was dense black, but after some exposure to the air it ac .

Jan 1, 1884

By Jacob T. Wainwright

The object of this paper is to describe some efforts and observations by the writer relating to this subject. Althongh the usual type of' blast-furnace is a most efficient device for smelting and melting purposes, it is not suitable for utilizing the cheaper grades of fuel, such as coal-slack and certain gaseous fuels. This problem not only involves the consideration of the furnace as a suitable apparatus, but also embraces the consideration of the chemical and calorific properties of the proposed fuel. In the hearth of the ordinary blast-furnace an extremely high temperature is maintained. This extreme temperature is due to the complete combustion of the fuel in the hearth, and before the gases reach the zone of fusion their temperature is reduced, by the absorption of carbon, 2300 degrees Fat). In a smelting-furnace, the maintenance of this extreme temperature at the hearth becomes useless when it can be reduced without

Jan 1, 1889

By Frank Linforth

THE object of this paper is to present a brief outline of the methods of geologic mapping employed in the Geological Department of the Anaconda Copper Mining Co., at Butte, and to show by means of a few typical examples the practical nature of the results obtained. The extremely complicated geological conditions early encountered in Butte mining led mine operators to realize the necessity of accurate detailed geologic mapping as an aid to successful development of the ore bodies. The organization of the Anaconda Geological Department was undertaken in 1900 by H. V. Winchell, who, in conjunction with D. W. Brunton, worked out the essential methods of procedure which are, in the main, followed at the present time. Since the year 1906 the geologic work has been under the direction of Reno H. Sales, and in some respects the scope of the work has been slightly enlarged. Au excellent article describing the general equipment of the geological department was presented by D. W. Brunton at the British Columbia meeting of the Institute in 1905.1 His idea, that data collected underground and recorded should be put to practical use and not remain a mere " inventory of the company's underground possessions," is the keynote to the success of applied geology in Butte. The geologic notes are taken as soon as possible after the ground is broken so that any mistake in the mining may be corrected at once, or any particularly advantageous procedure may be suggested before any useless work is done. Taking the notes underground is a comparatively simple matter, but a few necessary precautions may be pointed out. The essential to success is that the notes shall show exactly what geological facts are disclosed. The observer must discriminate carefully between important and unimportant exposures in making the record, especially as regards the relation between veins and stringers, between faults and minor slips, or between the characteristics of veins of different ages. A simple color scheme has been adopted for making this record: Red pencils are used to indicate.

Jan 11, 1913

By Gail Moulton

THE oilfields in Illinois are located principally along the LaSalle anti-cline in the southeastern part of the state. The oil produced comes most largely from beds of Pennsylvanian and Mississippian age, but there is an increasing important production from deeper horizons, as will be noted under new development. The oil is largely of paraffine base, and has an average specific gravity of about 35° Baume. The rank of Illinois as an oil producer has dropped from third since 1913, when its production was exceeded only by that of California and Oklahoma, to eighth in 1923. This has been the result of failure to find new pools of considerable size to offset the declining production of the old wells and of the greatly increased production of some of the other states. The noteworthy features of petroleum production in Illinois during 1924 are: the low rate of decline for the state as a whole; the smaller percentage of dry holes; and the larger average initial yield of the new wells.

Jan 3, 1925

Jan 1, 1909

By Frank Alfred Fahrenwald

A complete list of the elements as given for 1915 includes 18 that melt above 1,700" C. There does not exist one complete thermal equilibrium diagram for any pair of these 18 elements. Several of these elements have been combined, in relatively small proportions, with metals of lower melting point: e.g., tungsten, molybdenum, and vanadium, in steels, or with nickel and cobalt; but of this refractory group, platinum is the only one that has been extensively studied in this connection. When one considers that, with few exceptions, the industries have made use of alloys to the exclusion of pure metals, it is reasonable to expect that alloys of this refractory group will invade fields in which the pure metals have found little application. The past neglect of this class of metals has, no doubt, been partly due to the rarity of some of them, for even though alloys of very valuable properties should be developed, their cost, unless in exceptional applications, would be prohibitive. There is also a well-founded reluctance to undertake research involving very high temperatures which, in the case of most of these elements, must be accompanied by an inert atmosphere as well. This combination of high temperatures*and control of atmosphere within the heating chamber of any furnace of present design is a difficult problem. It is the purpose of this paper to give results,' of an investigation of one binary series of this group, in which methods were employed that avoided the usual difficulties accompanying high-temperature alloy investigation. , Historical.—The alloys of tungsten and molybdenum have received very little consideration during the past. A review of available literature reveals very little regarding this system, and that which has been recorded seems to be at fault. Mennicke2 writes, "Die bekannteste Verbindung

Jan 1, 1917

By R. S. McBride

The fertilizer industry is a meeting place of mining, manufacturing and agriculture. It is an industry of dynamic change, huge tonnages, and great aggregate value. In the United States from 5,000,000 to 8,000,000 tons of fertilizer are made and used per year, with a value at the works of from $200,000,000 to $300,000,000. The world uses about 50,000,000 tons yearly with an aggregate value between two-thirds and one billion dollars. This world output contains of the essential plant-food constituents, nitrogen, phosphate, and potash, approximately 8,000,000 tons. The corresponding United States quantity, as nearly as can be estimated, is 1,400,000 tons of plant food per year in the aggregate tonnage of fertilizer. With the steady increase in the practice of scientific agriculture throughout the world there has been a corresponding growth in the consumption of fertilizers. In the United States there has, indeed, been but a small upward trend in the tonnage sold, measured in millions of tons of all classes of goods which are made and marketed. The real growth has come through the increasing concentration of the essential plant foods in the mixture. Thus it is estimated that between 1920 and 1930, although there was little increase in tonnage of fertilizer, there was an increase of fully 30 per cent in the content of nitrogen, phosphate, and potash. Hence, the American farmer has actually been using more plant-food to

Jan 1, 1932

By Herbert E. Hawkes

“For his Pioneering leadership in the science and technology of mineral exploration, especially in the development and world-wide application of geochemical methods as major exploration tools, and for his lecture ‘Geothermal Hydrogen’.”

Jan 1, 1981

By John M. Pitt

A rapid in situ stress measurement technique was developed for exposed underground surfaces. The method applies radial stress in small diameter (38mm) boreholes, initiating fracture propagation which is monitored by measuring ultrasonic pulse velocity. Theoretical relations for stress concentrations near boreholes provide independent expressions for unknown principal field stresses at incipient fracture; fracture orientation defines principal stress orientation. Accuracy and precision were evaluated using blocks of brittle material subjected to known stresses. Results were comparable to those obtained by other in situ stress measurement techniques.

Jan 1, 1984

By Richard Pearce

IN looking around me for some subject on which to frame an address for this meeting, it has occurred to me that some results of observation and investigation, in regard to the varied conditions under which gold is found, may possibly prove of interest. The subject is one which frequently crops up in discussions at our meetings, but there is always an immense amount of uncertainty expressed as to the actual condition in which the gold exists in any particular ore. It follows, therefore, that any light which might be shed on this rather complex subject, would be of value to science and of service to mining and metallurgical practice. In some investigations which I have, from time to time, been led to make, for the purpose of determining to what extent an ore might be concentrated, I have been astonished at the very varied and apparently inexplicable results encountered, and have been naturally led to inquire into the causes for such seeming inconsistency. The mines of Gilpin county, Colorado, where gold was first discovered in that State, furnish an infinite variety of examples of its occurrence, and it was here that difficulties first presented themselves to the Colorado miners, in the sudden transition from what is called " free-milling gold-ore " to an ore characterized by properties which make the ordinary treatment by amalgamation stamp-mills utterly impracticable. So long as mining was limited to what might be called the zone of oxidation in the veins, just so long might amalgamation be conducted without difficulty; but directly the miner reached a point beyond the influence of the oxidizing power of the surface waters, the gold resisted all attempts at amalgamation, and recourse • was had to smelting.

Jan 1, 1890

By Benjamin C. Greene, H. Beecher Charmbury

Water is a most remarkable substance, essential for life of all kinds. As well as needing water to survive, man has always used it for agriculture, transportation, recreation, and many other things. When our country was young and inhabited by few people, the streams, rivers, and lakes were able to provide all the clean water needed by man and take away all the wastes created. However, with our growing population and an ever-increasing demand for goods and services, the public, industry, and government at all levels have become acutely aware of the need to manage the nation's water resources more efficiently. Abundant energy from many sources has helped this nation to become the greatest industrial nation in the world. Coal has contributed a major portion of this energy, generating electricity, running railroads, and maintaining national security during wartime. The result has been the highest standard of living in the world and a time of widespread economic prosperity. The use of water in coal mining is somewhat different from its use in most industries. With the exception of water used in cleaning plants, for underground dust control, and for fire protection, most of the water en- countered in coal mining operations serves no useful purpose. In other words, it is an undesirable element and must be removed, otherwise it will interfere with operations, cause potential water quality problems, and may even stop operations by flooding. In the past, removing water from working areas of most mines was usually a fairly simple matter. Pumps with piping were installed at sumps or low spots in the mine and the water was pumped to the surface or to drainage control facilities constructed for the operation. Ditches were often used to collect and drain the water by gravity to the outside or to main sumps for pump discharge. In either case, the water was allowed to flow into the nearest stream or river. The concept of "water is water" was generally accepted without too much concern for what was in

Jan 1, 1981

By William Glenn

The taking of proper samples of crude ores seems to he less thoroughly understood, or less carefully practiced, than its impor tance requires. We all know how often we encounter the reports of very accurate assays and analyses, the weight of which as evidence wholly depends on the method of obtaining the sample, and is very probably nil, because there has been no proper sampling. Pissages might be cited from technical books, and from current technical literature (all the work of writers whom we delight to honor) to show that even among high scientific authorities there is too little acquaintance with the practical art of the sampler. There is no metallurgical or chemical establishment which does not frequently receive samples truly representing nothing. They consist usually of bits of ore, or what not, selected because they are worse or better than the average of what they are meant to represent. And they are worthless, no matter who made the selection. Where conscious choice is permitted to enter into the operation, a fair sample will not result, unless by a miracle. The work of sampling is often looked upon as within the realm of boys and of pensioners only. At least, though the manual labor be left to subordinates, the principles on which it is conducted and the safeguards with which it is surrounded are not unworthy of the study of experts; and experts should he ready to teach these principles and enforce them in practice. For exact sampling is the indispensable first step towards learning the value of any boxful, carload or shipload of ore. I propose to give a simple account of the method of sampling by hand, such as I have always pursued. There is nothing new about it. So far as I know, it is the immemorial old method, as old at least as Cornish copper-mining. Perhaps my fellow-members in the Institute may suggest improvements in it. If not, it will constitute a record in our Transactions to which laymen and beginners may be referred.

Jan 1, 1892