Search Documents

By Fred C. Bond, Jen-Tung Wang

Comminution energy is principally energy of deformation before breakage, which appears as heat An empirical equation is presented which covers the entire comminution range. The new strain-energy theory considers comminution from the known principles of mechanics and the reduction ratio. Energy requirements according to the different theories the romnnred. THE present status of the theory of comminution is extremely unsatisfactory. The amount of various ores and rock products crushed and ground annually approaches the staggering sum of perhaps one half billion tons. Yet the basic concepts underlying an operation of such magnitude are unknown, and actual knowledge of what takes place in comminution is almost entirely empirical. The responsibility for this situation cannot be charged to apathy or lack of appreciation of the importance of the problem. Many attempts have been made to evolve a workable hypothesis, but none has been completely successful. General Considerations In order to break rock, it must be subjected to a stress which strains the rock beyond its critical breaking point. The stress imparts energy to the rock, most of which is released in the form of heat when the stress and resulting strain are removed. If the strain induced exceeds the critical strain, the energy is released by breaking; if the induced strain does not reach the critical point, the energy is released with removal of the stress as energy of resilience. Rock is a brittle material and it is assumed that it breaks approximately at its yield point, so that no permanent deformation results from strains below the critical. When rock is broken the total energy input is accounted for by the heat liberated, and by the surface energy of the new surface produced. A small and probably negligible amount is released as noise. Rock is commonly broken under compression and the applied stress is ordinarily compressive. However, for breakage to occur, it is only necessary that the induced strain exceed the critical value, and this strain may represent the resultant of compressive, shearing, and tensile forces. The stress-strain diagram of rocks under compression, and the modulus of elasticity as determined therefrom, should be fundamental considerations in the development of any theories of rock breakage. Crushing in jaw or gyratory crushers results primarily from a squeezing action, and reduction in a hammer mill is the result of impact. The action in rod and ball mills is a combination of impacting, squeezing, and wearing away by attrition, or rubbing. In ordinary crushing and grinding, the forces are applied at protruding points and are not distributed evenly throughout the rock. This is one of the features of comminution which theoretical considerations have not covered adequately. Another feature is the effect of impact velocities, which may greatly influence the total energy required for breakage. Impact velocities may vary from 1 or 2 fps in crushers to 10 or 20 fps for ball mills, and as high as 100 or more for hammer mills. However, according to the findings of geophysicists, the velocity of sound and of compression waves in stone is many times greater; the primary longitudinal compression waves travel at perhaps 15,000 fps, and the secondary transverse waves, which may reach the surface and cause cracks to form thereon, travel at perhaps 5000 fps. When a crack tip forms, the total surrounding stresses are concentrated in this tip, which rapidly extends throughout the rock particle.1 It would seem that the energy required to deform the rock beyond its critical strain, resulting in the formation of a crack tip, represents practically all of the energy required. Most of the primary crack tips presumably form on the surface. A simple method of designating feed and product size is necessary for the evaluation of crushing and grinding results. Taggart's suggestion2 that the 80 pet passing size be used has been found very practical. In this paper, the square opening screen size which 80 pct of the feed passes is designated as the feed size F, and the size which 80 pct of the product passes, or the product size, is designated as P. The reduction ratio at the 80 pet passing size, or F/P is designated as n. The feed and prod-

Jan 1, 1951

By H. R. Hanley

ELECTROLYTIC zinc produced from sulfate solution and, with pure lead anodes is always contaminated with a small and varying percentage of lead. The purpose of this investigation is to determine the characteristics of several lead alloys and their influence on the products of electrolysis and power consumption. The study of alloyed anodes has been a matter of interest for some years. Tainton, Taylor and Ehrlinger prepared a highly interesting paper1 on this subject a year ago, in which the effects of silver-lead and some ternary alloys of lead-silver-tin were described. The present paper describes a study of various combinations of 10 metals. The general plan of the work provides for the fabrication of the alloyed anode, its adequate conditioning by preparatory electrolytic operation, the production of cathode zinc and its analysis, the determination of the anode polarization, and other features. A list of the anodes tested, showing composition and polarization at various current densities together with the lead assay of the cathode zinc, is shown in Table 1.

Jan 1, 1930

'The Institute conducts jointly with the American Society of Civil Engineers, American Society of Mechanical Engineers and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them of certain properties. United Engineering Trustees, Inc. When Mr. Carnegie made his gift which made possible a home for the engineering societies, a separate corporation was organized to act as a holding company and to manage the common property. This was long known as the

Jan 1, 1932

By V. R. Garfias, R. V. Whetsel

As pointed out in previous studies, estimates of petroleum reserves if they are to be of value must not only presuppose a clear understanding of what is actually meant by reserves but must be subject to constant revision to conform with changes in their component factors. When such estimates are analyzed it must be clear that it is virtually impossible to obtain comparable figures reflecting the same degree of accuracy, to represent the reserves not only in various countries, but at times even of different fields in the same country. Estimates of reserves in the United States, subject to frequent independent checks, are obviously more reliable than those furnished, for instance, by the Soviet Government, as the latter must be accepted at their face value and are open to the suspicion of being made to conform with predetermined programs of propaganda. Any tabulation of the reserves of all producing countries, therefore, gives a total that is misleading, as the component items arc not arrived at on the same basis and therefore are not homogeneous in a true sense. Only a fraction of the petroleum stored underground, usually associated with natural gas, is or can be brought to the surface, and although practically all the natural gas underground can be rccovered, in actual practice in some fields a large part of the gas that reaches the mouth of the well is wasted. It is thus estimated that in the United States only some 25 to 35 per cent of the petroleum underground in proven fields is actually economically recovered. Estimates of reserves, therefore, should make clear the distinction between the known amount of oil underground in producing fields and the portion that actually can be brought to the surface. It cannot be overemphasized that as a result of the operation of the "Law of Capture," which controls subsoil ownership in the United States on comparatively small landholdings that seldom if ever cover the entire producing area, the oil fields are not as economically exploited as some forrign fields, and that as a result (were it not for the easy accessibility of the domestic market, the largest in the world) some American production would now be unprofitable in open competition with foreign oils.

Jan 1, 1939

The opening session of the Institute was held at Hazle Hall, Tuesday evening, October 27th, with a large attendance of members. President Raymond called the Institute to order, and after a few introductory remarks, introduced Mr. I. Lowthian Bell, President of the Iron and Steel Institute of Great Britain, and Honorary Member of the American Institute of Mining Engineers. Mr. Bell was received with great applause, and made his acknowledgments in a brief speech, of which the following is the substance: He desired to thank the Institute personally for the honor conferred upon him in his election to membership, and also for the invitation extended last year to the body of which he was President. The difficulty felt by many members of the Iron and Steel Institute, of leaving for a long journey the works of which they had charge, aggravated by special industrial troubles at the time of the invitation, had obliged them to conclude that it could not then be accepted in a fitting manner. The iron .manufacture of this country is a subject of great interest to Englishmen, who look with pride upon the achievements on this side the water of the descendants of a common ancestry. His own reception in this country had far surpassed in cordiality even the well-grounded anticipations he had formed from the assurances of the President and other friends. Notwithstanding the flattering manner in which his friend, in introducing him to the Institute, had spoken of his contributions to the science of iron metallurgy, he could not take to himself alone the significance of this welcome. He knew it was a recognition of the services rendered by the body which he had the honor to represent; and he was glad to see present a member of that body, Mr. Thomas Whitwell, who had fortunately been able to make the journey at this time, arid whom he had had the pleasure of meeting on the shores of Lake Champlain. He had been requested to say something of his impressions of the American iron industry. It was not easy to digest so soon the vast

By R. V. Whetsel, V. R. Garfias

As pointed out in previous studies, estimates of petroleum reserves if they are to be of value must not only presuppose a clear understanding of what is actually meant by reserves but must be subject to constant revision to conform with changes in their component factors. When such estimates are analyzed it must be clear that it is virtually impossible to obtain comparable figures reflecting the same degree of accuracy, to represent the reserves not only in various countries, but at times even of different fields in the same country. Estimates of reserves in the United States, subject to frequent independent checks, are obviously more reliable than those furnished, for instance, by the Soviet Government, as the latter must be accepted at their face value and are open to the suspicion of being made to conform with predetermined programs of propaganda. Any tabulation of the reserves of all producing countries, therefore, gives a total that is misleading, as the component items arc not arrived at on the same basis and therefore are not homogeneous in a true sense. Only a fraction of the petroleum stored underground, usually associated with natural gas, is or can be brought to the surface, and although practically all the natural gas underground can be rccovered, in actual practice in some fields a large part of the gas that reaches the mouth of the well is wasted. It is thus estimated that in the United States only some 25 to 35 per cent of the petroleum underground in proven fields is actually economically recovered. Estimates of reserves, therefore, should make clear the distinction between the known amount of oil underground in producing fields and the portion that actually can be brought to the surface. It cannot be overemphasized that as a result of the operation of the "Law of Capture," which controls subsoil ownership in the United States on comparatively small landholdings that seldom if ever cover the entire producing area, the oil fields are not as economically exploited as some forrign fields, and that as a result (were it not for the easy accessibility of the domestic market, the largest in the world) some American production would now be unprofitable in open competition with foreign oils.

Jan 1, 1939

By Clarence Linville

FULTON1 says: "Speiss is an artificial arsenide of iron containing smaller amounts of other metals. In constitution it is similar to a matte except that arsenic replaces sulfur." For the purposes of this paper it will be necessary to broaden the definition, and I propose the following: Speiss is an artificial mixture of arsenides, of which arsenide of iron may be taken as a type, but iron may be replaced in part or wholly by other metals (such as copper, nickel, cobalt, lead and zinc) and the arsenic may be replaced in part or wholly by antimony. In addition to antimony and arsenic, speisses often contain sulfur. Speisses usually also contain both silver and gold. Table 1 illustrates the variations that may be encountered. TABLE 1.-Speiss Analyses

Jan 5, 1925

F. E. BACHMAN, Port Henry, N. Y. (written discussion*).-Experi-ments with titaniferous ores found in Essex County, New York, made by the MacIntyre Iron Co. in 1914, showed' that titaniferous concentrates are reduced in the furnace with no greater, and probably with less, expenditure of heat, and consequently of fuel, than non-titaniferous mag-netites; and as a greater proportion of their oxygen is removed by carbon monoxide than is the case with non-titaniferous magnetites, a lower fuel consumption for the reduction of iron may be expected. After the furnace was blown out at the end of the experiment, the formation in the hearth was found to be abnormal. The brickwork was replaced, entirely around the furnace, by a layer which at -the tuyere circle was made up of cinder, fine carbon, and coke; the coke, however, gradually disappeared toward the bottom, being replaced by cinder and graphite. The usual salamander of graphite and iron was missing. The material left in the hearth seemed to be cinder that had not drained from the last cast; its composition, though, would indicate that it was in the furnace previous to the taking off of the titaniferous ore. At first, this material was thought to be blast-furnace cinder mixed with less iron and graphite than is normal; but an examination showed it to be made up of cinder with small masses of iron and graphite. There were also patches of a steel-gray material having a metallic luster; a microscope showed these patches to be made up of black metallic crystals interlacing white crystals.

Jan 11, 1919

By J. J. Frawley, W. J. Childs

PREVIOUS studies have shown that if a supercooled liquid metal was perturbed by vibration the probability of nucleation is is During a recent investi- gation to determine quantitatively the amount of energy needed to cause nucleation in a given supercooled liquid specimen, it was found that at low-energy values in the megacycle range, below the threshold energy value for cavitation, the amount of dynamic supercooling was greater than the amount of static supercooling. That is, if a specimen had a given amount of thermal supercooling under static conditions, its thermal supercooling could be increased by the addition of low-energy sound waves. The material used in this investigation was high-purity bismuth. This material was chosen because of its low melting point and the high degree of supercooling which could be easily obtained. The sound gener- ator employed in this work was a commercially built Sperry ultrasonic testing unit. This unit was equipped with a barium titanate crystal as a piezoelectric transducer. These sound waves were transmitted to the supercooled melt by a Pyrex rod, as shown in Fig. 1. The transducer was coupled to this Pyrex rod wave carrier by motor oil. The Pyrex wave carrier was approximately 1.5 ft long to prevent damage to the transducer by heat. The diameter of the Pyrex wave carrier appears to be critical. In the initial tests a wave carrier of 0.5 in. in diam was employed. However, the sound waves had no effect on the amount of dynamic supercooling. When the diameter of the wave carrier was increased to approximately the inside diameter of the Pyrex crucible, the sound waves were more effective. Approximately 200 g of metal was melted under a stannous chloride flux in a 30-ml beaker by induction heating. The temperature was recorded by a Pyrex-encapsulated chromel-alumel thermocoule which was placed in the beaker after the bismuth melted. The Pyrex wave carrier was immersed slightly below the surface of the liquid bismuth and the specimen was reheated to about 500°C. It was observed that the amount of supercooling depends on the amount of superheating the specimen receives; therefore, for meaningful results the amount of superheating was the same for all heating cycles. The specimen was allowed to cool in air and the change in temperature was continuously monitored with a potentiometric strip-chart recorder.

Jan 1, 1969

By P. Martignan

UNTIL quite recently, Alsace was the only district in France where petroleum could be found in somewhat industrial quantities. The Pechelbronn fields produce, however, only about 80,000 tons a year, which represent approximately one-eighth of the domestic consumption. Much research work has been done in Alsace to find the prolongation of the Pechelbronn fields, but instead of oil the drillings revealed the existence of large deposits of potash. This can, be easily explained when one remembers that the Pechelbronn oil is of the Oligocene period, and, that in the Alsatian stratification the Oligocene lies immediately on the Keuper, i. e., on the strata that originate from a period during which the largest salt and potash deposits were constituted. Before the war, and mostly at the end of the last century, some wells were drilled in various districts of France where some analogies could be found with the Alsatian geology, the borings being mainly made in the Triassic and Tertiary beds. They led to negative results. After the war, the growing importance of oil urged the necessity of resuming the explorations. But it is our belief. that this was greatly facilitated by the enacting of new legislation, which is embodied in the Mine Act of May 16, 1922.

Jan 3, 1925

By A. H. Bell

The results of repressuring (or gas-drive) have been very encouraging to the several companies doing experimental work along these lines in California. The most notable examples are the Shell and the Union Oil companies at Dominguez, the Marland Oil Co. at Seal Beach, and the California Petroleum Corpn. at South Mountain. The results of the Marland test at Seal Beach are interesting in that re pressuring was started while several wells were still flowing; also, on account of the high pressures required to overcome the hydrostatic pressure exerted by high-head edge water. The well first chosen for repressuring is about halfway up the flank of the structure and had been on the beam making about 250 bbl. of fluid daily, cutting about 60 per cent. emulsion. The fluid lcvel was 230 ft. from the surface and the top of the sand was 4393 ft. Tubing was run to 4000 ft. with a packer and the space above the packer was filled with water to balance the high pressures. Gas was started in slowly to allow the fluid to be pushed back into the sand, and required three days at a pressure of 1500 Ib. per sq. in. before starting into formation. The pressure was once built up to 1800 Ib. and the compressor was shut down for a few hours. When again started, the well took gas at 1500 Ib., and after about three weeks the pressure was dropped to 1450 Ib. The present pressures required range between 1400 and 1450 lb. Volumes as high as 1,500,000 cu. ft. per 24 hr. were put into the well. Increases as high as 50 per cent. in production were obtained in wells up-structure with very little increase in wells down-structure. Also, the water cut on one edge well materially decreased. After about 40 days the repressuring was moved to two wells farther down-structure and the well originally repressured was put on production. The result of this was a great increase in the production of wells one location farther down-structure, a rapid increase in one well one location up-structure, and a decrease in production of the wells farthest up-structure. Later the gas started to short-cut to the nearest well down-structure, nullifying to a certain extent the effects of the repressuring work. The increased production that could be definitely attributed to the repressuring work

Jan 1, 1928

By J. Walter Scott

IT is usual practice in the copper industry to use open horizontal molds for casting tough-pitch copper wire bars.1 A wire bar cast in this manner is partly characterized, by heavy wrinkles and a comparatively deep skin of oxide on the top of the bar, corresponding to the open side of the mold. On the theory that the rough, high-oxide surface might have an adverse effect on the rolling and drawing properties of a wire bar and might account for some of the irregularities of mill behavior, several bars which had been planed to remove the wrinkled surface were processed into wire. These bars responded to mill treatment more satisfactorily than did the regular wire bars. Realizing that machining the surface of one face of each bar would not be commercially feasible, it was decided that casting the metal into a vertical mold and cropping off the pouring end would accomplish. approximately the same result. Several wire bars of commercial size (250 lb.) were so cast and processed into wire for comparative test with bars cast in the usual horizontal molds. It is the purpose of this paper to present the results obtained from this investigation, in which commercial bar sizes and processing technique were used throughout. The results show that in general copper wire bars cast vertically are superior to those cast horizontally.

Jan 1, 1930

By E. H. Barton

The necessity, on the Pacific Coast and throughout the semiarid regions in particular, of the conservation of waters for agricultural, industrial and mining purposes has forced itself upon the minds of those directly or indirectly interested in these industries. To meet the requirements of the case, storage must be provided for the flood-waters so abundant during the rainy season in order to insure a constant and unfailing supply during the summer months. Such storage can only be obtained, in the greater number of instances, by the erection of reservoir-walls of great height. The feasibility of employing earth or timber in the construction of such high dams is questionable, especially when (as is often the case) they must be placed in torrential streams. The experience of recent years with masonry dams, throughout this and foreign countries, has demonstrated that such dams, when intelligently and correctly designed and properly constructed, will meet the requirements of larger storage by means of increased height. The failures of masonry dams have been few; only two of any consequence being on record, namely, that of the Puentes dam, in Spain, in 1802, and that of the Habra dam, in Algiers, in 1810.* On the other hand, the failures of wooden and earthern dams are innumerable. The following are some of the most important structures constructed in recent years. The list is taken from Mr. Wegmann's book, just cited: The Furens, Zola, Ternay, Ban and Verdon dams, in France; the Nizar, Lozoya, Villar and the two Hizar dams,

Jan 1, 1900

By V. Annamalai, J. B. Hiskey, L. E. Murr

The kinetics of copper cementation on rotating disks of body and tear-top beverage can aluminum alloys were studied as a function of temperature and copper ion concentration. Both alloys followed the two-step kinetic regions, an initially slow rate followed by an enhanced rate. Experimental activation energy determinations (9.04 to 19.62 kJ/mol) indicated that ionic diffusion controlled the reaction mechanism between 20° and 60°C. At low temperatures (< 20°C), the system appeared to be controlled by the presence of an aluminum oxide surface film. The results of this study showed that cementation kinetics for the beverage can aluminum alloys are similar to those for pure aluminum. It was also found that the chemical removal of the oxide layer is less important for the alloys than /or the pure aluminum system. The characteristics of the resultant copper deposits were studied under a scanning electron microscope, and the reaction kinetics seemed to depend strongly on the nature and morphology of the deposits. In addition, maximum rates occurred when the deposit structures were fine feathery dendrites.

Jan 1, 1980

By J. H. Keeler

QUESTIONS raised during earlier investigations of the preferred orientation in titanium1 and zirco-nium sheet led to the examination of the rolling and annealing textures of beryllium and hafnium sheet. Since the c/a ratios are 1.568 and 1.584, less than that of ideal close packing, 1.633, it would be expected that the preferred orientations would be similar to those exhibited by zirconium and titanium. This was found to be true. However, in several regards the orientations observed for beryllium differed from those reported by Smigels-kas and Barrett4 and so are given here. The okientations for hafnium are presented since only the cold-rolling texture has been reported in the unclassified literature. The pole figures were determined by transmission using an X-ray spectrogoniometer with copper Ka radiation and the automatic pole-figure recorder designed by Geisler described previously.6 The intensity units in the pole figures in this case are only arbitrary since calibration against a random sample of the same material was not considered necessary for the original purpose of the examination. The beryllium sheet, cold-rolled from 0.036 in. to 0.006 in., a reduction of about 84 pct, exhibited a split texture with the [1010] direction in the rolling direction as shown in Fig. 1. The same specimen annealed in vacuo for 1 hr at 1000°C showed no change in orientation. These textures

Jan 1, 1959

By ELTCENE A. WHITE

WE are all interested in our ou7n lines of endeavor and consider ourselves the center of the universe. The farmer thinks he is the most important man because he feeds us. The doctor knows he is the real center because he keeps us well. The lawyer says that he is indispensable because he keeps the peace. The banker furnishes us a place to keep our money and tells us how to make proper use of it. The miner sags that without metals there would be no civilization. I think that my branch has sufficient interest and exhilaration. of accomplishment to fully occupy any man&apos;s mind and attention. Mining and metallurgy are as old as the human race. It did not have much, if any, importance in the stone age as there are not found remains of iron and copper, but in the bronze age, which was co-existent with the stone age, it came to the front. Iron and copper were the most important metals. Copper, as bronze, was known in ancient Egypt, I\~:IS important in Rome and other parts of Europe and in Asia; in South America among the Aztecs and farther North were the Mound Builders and the early inhabitants of Lake Superior. At a very early date the Egyptians conquered the Sinai peninsula for the sake of the copper produced there. The history of copper metallurgy can be compared to that of a flower. The seed is sown in darkness and in the Dark Ages the crude metallurgy of copper began. As the shoot comes up from the seed it may be compared to the age of alchemy; the branches of the plant can be compared to the Middle Ages; the flowering shoots to the 17th century, the budding to the 19th and the blossom to our own time from 1870 on.

Jan 1, 1930

By R. V. Ramani, G. W. Luxbacher

The approach proposed in this paper is, as stated by the authors, an update of methods well discussed in the literature. The authors are to be congratulated for their excellent effort in quantifying a difficult problem with realistic cost data. Economic analysis of the components of a mine ventilation system is complicated by both the dynamic nature of the system and the uncertainty as to the time when system changes occur. We wish to address three specific areas of this paper which require further consideration: shaft designed air capacity, shaft location, and economic criteria used within the analysis. With regard to ventilation shaft size optimization, the system complexities are illustrated in the quantity flow through the shaft. Obviously, the capacity chosen by the designer is a static parameter while the utilized capacity is usually a dynamic variable over the life of the shaft. The designed capacity may be used for a short or a long period, and this may occur during the beginning, middle, or near the end of the shaft life, leading to different operating costs at different times. Operating costs, as shown by the authors&apos; Eq. 8 are more dependent on air quantity than any other single factor (quantity cubed as compared with other factors to the single power); hence, extreme accuracy in the assessment of some of the other factors discussed by the authors may be secondary to the quantity estimation. Incorporation of a variable usage factor for air quantity over the life of the shaft in this optimization problem deserves some consideration. Although the authors have chosen to examine optimum ventilation shaft sizing, it must be remembered that optimization of the whole system-is the primary objective of any optimization process; unit optimization of such items as shafts may not complement the overall process. We have discussed this subject in some detail in another paper in this Transactions volume (Luxbacher and Ramani, 1979). While the recommended process by Wang, et al. can be used in shaft sizing, the shaft operating conditions (pressure head and air quantity) are intertwined with the shaft location within the mine infrastructure:

Jan 1, 1980

By R. V. Wheeler, F. V. Tideswell

Coal being essentially a complex conglomerate of plant remains that have undergone decay and interaction in varying degree, it is understandable that attack on the problem of its chemical constitution by normal chemical methods should have been attended by but slight success. The obvious method of fractionation by means of selective solvents has yielded a few results of some value. Thus it is known that from many, if not all, bituminous coals organic solvents extract small percentages of oxygenated compounds, which are generally assumed to have been derived from the original plant resins, though a more probable source would appear to be the glycerides and waxes of the plants. Organic solvents also extract small proportions of hydrocarbons, the origin of which is doubtfill. Of more importance is the action of such pseudo solvents as pyridine, which, in addition to their specific solvent action, have the power of resolving and simplifying a portion of the coal substance in a manner analogous to that by which water can disperse a hydrogel. Early work with pyridine indicated that coals are composed of two main classes of compounds: the one soluble in organic solvents, the other capable of being partly dispersed in pyridine. Recent work has shown that the dispersion is colloidal in character and that it may be accomplished by the use of solvents less active than pyridine, such as benzene or chloroform, provided that the temperature of extraction is raised or the coal has been suitably preheated. The action of reagents on coal has proved of little value in the past, but some insight into the constitution of coal has been given by regulated destructive distillation. Thus, it has been shown that coals behave on distillation as though composed of two main classes of compounds: the one readily decomposable at moderate temperatures (yielding mainly the paraffins), the other undergoing a preliminary early decomposition (with evolution of oxides of carbon and water) and yielding a residue that at higher temperatures breaks down, yielding much hydrogen.

Jan 1, 1925

By Robert S. Schecter, Mark P. Walsh, Michael J. Humenick

In recent years in situ leach mining has emerged as a viable technology for the recovery of uranium from strata in South Texas which contain relatively low concentrations of uranium ore. Because the ore bodies lie within ground-water aquifers, a significant determinant in the economics is the requirement that such aquifers be protected from contamination. Since ammonia is one of the constituents of the leach solutions now being field tested, one environmental problem to be resolved is the removal of ammonia at the end of mining. A second related question is the fate of the ammonia which is not removed by the restoration procedure. This paper considers the displacement and migration of ammonium in a flowing electrolyte with concomitant ion exchange. The ion exchange is an important feature since, during the solution mining phase, ammonium saturates the mineral exchange sites and must be removed from these sites. A mathematical model is used to simulate this process and the model is tested against the results of laborator.y experiments. It is found that the simulations are adequate if an appropriate selection of parameters is made. The model is then used to investigate the effect of cation composition and concentration of the restoration medium as well as dispersion on the overall effectiveness of the process. It is concluded that increasing the concentration of monovalent ions in a solution containing a mixture of both monovalent and divalent ions decreases the adsorption selectivity of the divalent ions with respect to all monovalent ions including ammonium. Thus increasing the ionic concentration of a restoration fluid by increasing the concentration of a nonselectively adsorbed (with respect to ammonium) ion may have a very limited benefit.

Jan 1, 1979

I have attended these meetings, every year, since 1926 and have served on both the Pittsburgh and the National Executive Committees, so that I am fully aware - of the ruling of this organization regarding, "No Papers by Vendors". Since I am now classified as a VENDOR, I wish to express my sincere appreciation for the invitation to formally discuss these very interesting papers --all of which herald the coming of an entirely new era in the manufacture of quality steels. I also appreciate the references by Mr. Mosser and Dr. Swinkels to my first paper on the oxygen probe which was presented at the meeting of this group, here in Chicago, in 1966 and was subsequently published in the NOH Proceedings of that year. (1)

Jan 1, 1972