Search Documents

By Theodore H. Orem

In 1928 Elam,1 discussing the subject of twinning in metals, disclosed that she had observed this phenomenon in aluminum, a metal little susceptible to twinning. The twinning described was one in which the boundary between the twinned portions was not a geometric plane but appeared, in one section, more like a normal grain boundary. Under these circumstances twinning might remain unrecognized by an observer of microscopic sections. She therefore suggested that twinning in aluminum might be much more prevalent than expected. Whereas the parallel composition lines shown in sections of polysynthetic twins were characteristic of the phenomenon of twinning, Elam pointed out that from the absence of

Jan 1, 1963

AS If see it, then, the engineering advances of which yob have studied here at Golden, the continued growth of. industry that you see about you here in Colorado, and the country-wide progress that I have not time to discuss-these illuminating facts should clear away any doubts as to your future. You have little license to ask, "Where is the call for engineering or what the need? Yankee fashion I might ask you by way of reply, "Have all the mines been opened? Have all the power-houses and transmission lines been built? Have the last improvements in. mill and smelter been in-stalled?" We know that the general answer is No, and the rest of the answer, which tells where are those mines and power plants and what are the new methods and processes in mining and metallurgy, must be sup-plied by you engineers of the future. And anyone who has even casually observed what recent years have brought forth in our profes- sion cannot but envy you your job. Our reconnaissance excur-sion into your future should not be much longer extended, but before turning back there are four landmarks that I would like to point out-not lofty peaks but useful tie points that are worthy of your attention as you traverse the territory of your future work. Two of these are in fact low spots or depressed areas which call for engineering activity; these are commonly called "waste" and "average." The other two are of larger significance and are rather extensive regions in the domain you are to enter and occupy. These larger tracts bear the suggestive place names "fact-finding" and "human engineering" and perhaps will prove to be the heights from which the broadest outlook is to be had in this "pilgrim's progress:" In the first place, waste deserves your attention, al-though I realize that it is possibly the most unpopular word anyone hailing from Washington can publicly utter. Its unpopularity naturally follows from its overuse in the somewhat strong charges made against the industrial and business world some years ago, when the doctrine of conservation was first preached in the land. But waste is a word to be used in an engineering sense as well as for political effect. Properly used, waste is not a word to shy at-rather it is a challenge to the engineer. For example, at present, the loss of 1 kilowatt-hour to every 5 sold is a clarion call to the electrical engineer. Waste is your target to shoot at, the obstacle for you to surmount, the giant for you to slay.

Jan 7, 1928

By P. E. McKinney

DEVELOPMENTS in engineering during the past decade, particularly as applied to marine construction, mining machinery and other purposes in which corrosion offers a serious problem, have created a large demand for a non-ferrous metal highly resistant to corrosion and at the same time useful in general construction work as a substitute for steel without materially decreasing the factor of safety or increasing the weight of the various parts over that ordinarily used in the case of mild steel. To obtain the combination of desired properties many compositions have been proposed and used with excellent success, but at the present time probably the most popular and most widely used combination is the non-ferrous alloy commonly called manganese bronze. This is nothing more than a high brass to which have been added, by the proper method of alloying, comparatively small percentages of aluminum, iron, or manganese with the definite purpose in view of strengthening the alloy and rendering it more dense and close-grained than the average yellow-brass casting. In the manufacture of manganese bronze a great deal has been said about the importance of using only the highest grades of raw material and the beneficial or detrimental effects, as the case may be, of various impurities, as well as the importance of adding the ingredients according to various formulas proposed; but in most of these cases the literature on the subject has dealt principally with the manufacture of this alloy from virgin metals And raw materials of the highest purity. It is the purpose of this paper to deal particularly with the possibilities that lie in the proper development of methods for manufacturing such an alloy by more economical methods than those which have usually been discussed in other literature on the subject. Shortages have recently existed in raw materials needed for many products entering into the various branches of engineering work, particularly the non-ferrous metals, and during the next few years of reconstruction the country will be flooded with many

Jan 2, 1919

By E. P. Pfleider, C. A. Dufresne

The problem of mooing open-pit ores over large vertical distances is increasing in importance because of the immense deposits being mined. Gravity fall of ore through transfer raises to central haulage points underground has advantages for certain open-pit operations, and this method is being seriously considered for the Carol Project now underway in Canada.

Jan 6, 1961

By E. C. Mahan

THE text of my talk was suggested by the invita-tion of your secretary, who said that the excess productive capacity of the bituminous industry was a matter of common concern to engineers and coal operators. Cognizant of the depressed condition of the industry, he tactfully added that in common council we might find wisdom. Certainly it would seem that the application of the best engineering knowledge available would be helpful in solving mining problems. There is no doubt that clear thinking, characteristic of the engineering type of mind, is essential to untangle the shapeless pattern which increased complication, so often mistaken for progress, has developed. There is much thinking today which neither looks forward to a logical combination of ideas nor backward to simple fundamentals. The result of that sort of thinking is hopeless confusion. Lately we have heard much about excess capacity and overproduction, along with their attendant evils. Respecting the bituminous coal industry, these terms have been frequently misused. How many of us have seen them applied to the coal industry but how few of us have understood them. I am reminded of a state-ment which William Green, president of the American Federation of Labor and a former miner from the Ohio field, gave to the Associated Press last month, in which he was quoted as saying: "The coal men must realize that conditions have altered since the World War. To-day they are producing a billion tons a year, with a market for only half that tonnage." I cite this instance as a glaring example of the flood of. loose statements about the bituminous industry with which the public is being deluged. If the general public, or some of the newspapers, had any passion for the facts, this sort of misleading statement would not get very far. Unfor-tunately, in these days, opinions are more sought after than facts, and statements by such a person as Mr. Green and are promptly accepted by a credulous public.

Jan 4, 1928

By E. O. Lilge, H. Siebert

A design of a multiple-bomb leaching unit particularly suited for the study of heterogeneous reactions, i.e. sol id-liquid-gas interfaces at high temperatures and pressures is presented. The component parts and overall design are described and illustrated in detail. The system has been tested by a limited number of experiments and found to work satisfactorily. Heterogeneous reactions at solid-liquid-gas interfaces, at high temperatures and pressures, are studied in either autoclaves1'4 or bombs5'9. Autoclaves are usually fairly large vessels which have a stirring arrangement incorporated in the design. Mechanical design limits the use of these vessels to relatively low temperatures and pressures. They are particularly well suited to rate or kinetic studies. Bombs can be designed to be operated at high temperatures and pressures, and are smaller vessels; because of this, stirring arrangements are not easily incorporated. In this paper a multiple-bomb system is described, that has been designed to incorporate the desirable features of both the autoclave and the bomb. The described unit has flexibility for an over all study of leaching. Most of the component units in this assemblage are standard equipment, designed and produced by well known manufacturers. No claim is made to the design of this equipment, and although described in some detail, this is done merely for clarity in the elucidation of the system presented. The general layout of the multiple-bomb assemblage is shown in Fig. 1A and 1B. The basic units in this system are: 1) 6 stainless steel 100 ml bombs (Fig. 4)

Jan 1, 1964

By E. H. Rennhack

When cast hypoeutectic Zn-Ti alloys are rolled, the TiZn15 compound particles arising from eutectic decomposition form a network of fibers promoting improved creep resistance.' The effect is magnified with increasing titanium content and extends to hy-pereutectic concentrations. Strip produced from the latter-type alloys, however, also contains large, primary crystals of the compound that tend to initiate cracking during subsequent fabrication operations. In a study of the influence of various casting modifications on the size and distribution of these crystals, the phase relationships existing between the eutectic and the TiZnIs intermetallic compound in the Zn-Ti system were of major interest. Although several in- vestigators1 4 have explored the equilibria within this compositional range, their results show considerable lack of agreement. Consequently, with the exception of the solvus boundary, the constitution of this system containing up to approximately 1.0 wt pct Ti was . The findings are reported in the present note.

Jan 1, 1967

By K. Stout, E. Van Eeckhout, L. Friel

Previous research at the Montana College of Mineral Science and Technology indicated that it is practical and economically feasible to place stiff back- fill in a cut-and-fill stope. This backfill would reduce wall closure and high stress buildup in pi1llars, thus alleviating rockburst potential. Three ;topes from the Sunshine Mine, of the Coeur d’Alene Mining District, were chosen for a test verification of this concept. Although the first stope was lever mined beyond the initial cut (for economic reasons), some vibrating wire stressmeter results were obtained and found to compare favorably with numerical predictions. Some other instrumentation devices were built and tested, but never installed .

Jan 1, 1984

By Thomas M. Drown

Theodore Dehon Rand was appointed Treasurer of the American Institute of Mining Engineers by the Council, at the Boston meeting of February, 1873, to fill a vacancy caused by the resignation of the treasurer who had been elected at the first meeting in Wilkes-Barre in May, 1871. He was elected by the Institute to this offce in the following May, and yearly thereafter until 1903. He often alluded with amusement to the abrupt way in which he was injected into this position, by my coming to his office and asking him to accept the appointment as Treasurer, on the ground that he was eminently fitted for the position by reason of his legal and business knowledge, his interest in geology and mineralogy, and more particularly because he was a neighbor of the person (to wit, myself) who was slated for the Secretaryship, and they could thus convenient.ly confer on Institute matters. He consented, on condition that the duties should not involve too.much additional work for him. This assurance was easily given, for the Institute then

Jan 1, 1904

Jan 1, 1904

New Products Equipment

Jan 4, 1953

Jan 1, 1917

By I. Fatt

Networks of resistors are used as analog computers to obtain relative permeability and resistivity index curves for networks of tubes. These curves have all of the characteristics of those obtained on porous media and, therefore demonstrate the validity of the network of tubes model. INTRODUCTION In paper I' of this series the network model was shown to give information on the structure of porous media that could not be obtained from the bundle of tubes model. The agreement between the capillary pressure characteristics of a network of tubes and those of typical porous media does not prove the validity of the network made. The bundle of tubes model, although it gives less information, also shows this agreement. In this paper the flow properties of a network of tubes are shown to be in agreement with flow properties of porous media. The flow properties of the bundle of tubes model are not in adequate agreement with those of porous media. The dynamic properties of porous media, such as fluid permeability and electrical conductivity, have been found experimentally to be more sensitive functions of structure and pore size distribution than are the static properties such as porosity and capillary pressure characteristics. The network model can, therefore, be best tested by comparing the dynamic properties of a network of tubes with the observed properties of porous media. All static and dynamic properties of a completely valid model must agree with the observed properties. The most commonly measured sensitive dynamic properties are the relative fluid permeability and the relative electrical resistivity. Experimental measurements of these dynamic properties on sandstone, sintered glass, sintered alumina, and soil are reported in the petroleum and soil science literature. These properties were chosen, therefore, for the test of the network model. In the network model, relative permeability is the permeability of the network when some of the tubes are not conducting fluid, relative to the permeability when all tubes are conducting fluid. Similarly, the relative resistivity is the electrical resistivity of the network of tubes when some of the tubes are filled with a nonconductor. relative to the resistivity when all tubes are filled with the electrical conducting fluid. Single Size Tube Network The simplest porous medium is one in which all pores are of the same size. Such media can be approached by packing beds or columns of uniform size particles of sand, glass, or metal. The model of such medium in this study is a network of single size tubes. The network form, the ß factor, is usually not known for real porous media. If the validity of the network model can be established, then the study of the flow properties

Jan 1, 1957

By T. Egleston

There has alrvays been atheory among those working placer mines that gold is both folind rusty," and becomes so under treatment, hy which they nleun, not that gold becomes coated with oxide: of gold, but that it, is either coated superficially or alloyed with some substsnee which prevents the contact with mercury,and thus precludenthe possibility of amtrlgamation. To such aoiiditions of the

Jan 1, 1881

By T. Egleston

THERE has always been a-theory among those working placer mines that gold is both found " rusty," and becomes so under treatment, by which they mean, not that gold becomes coated with oxide of gold, bat that it is either coated superficially or alloyed with sortie substanee 'which prevents the ,contact with mercury, and thus precludes the possibility of amalgamation. To such conditions of the

Jan 1, 1881

By Waldemar F. Dietrich

Mineral fillers are relatively inert chemically under the conditions of use but have physical properties* that modify those of the materials in which they are incorporated. The mineral fillers considered in this article are asbestos, barite, clays, diatomite, crushed limestone, limestone whiting and lime, mica, silica, talc and soapstone, and pyrophyllite. Slate and stone, other than limestone and its derivatives, are excluded because, even though used in large quantities, they are exceptionally low-cost materials generally produced close to the area where they are used.

Jan 8, 1959

HONORARY Membership in the Institute is limited to twenty and the roster is now only fifteen, so Dr. Reynders becomes a member of a select circle. All of his life, following graduation from Rensselaer Polytechnic Institute in 1886 at the age of twenty, lie has been connected with the steel industry. For about thirty years he stayed with the same company, the Pennsylvania Steel Co., until it was acquired by the Bethlehem Steel Corp., in 1916. For many years he had been vice-president and general manager. Before he attained that position, Dr. Reynders organized and remained in charge of the bridge-building department of the company, and during his professional life he has directed the construction of many

Jan 1, 1938

By AIME AIME

CADWALLADER EVANS JR. has long been a leading figure in the anthracite mining industry and one of Pennsylvania's prominent citizens. He is, in fact, a native son, having been horn in Pittsburgh on Sept. 17, 1880. At Lehigh, from which he graduated in 1901 with the degree of Mechanical Engineer, Tom Girdler was a classmate, and both were active in football affairs. Going hack to Pittsburgh, he got his first job as trouble shooter for the Oliver Iron & Steel Co. A year later he entered the coal industry, getting a job with the Blaine Coal Co. as inspector of construction and later was superintendent of the Blaine mine at Elizabeth. Pa.

Jan 1, 1943

By S. A. Ford

I WOULD like to call the attention of our Bessemer steel manufacturers to a few facts in regard to the action of the manganese in. the Spiegel with the oxide of iron in the blown iron. The oxygen is united with the iron as a magnetic oxide, as Gautier asserts, and this oxide is reduced to a protoxide by one-atom of the manganese uniting with one atom of the oxygen of the magnetic oxide of iron. This oxide of manganese and the protoxide of iron thus formed unite with the silica which has been formed by the oxidation of the silicon in the pig iron. Mr. Snelus and others

Jan 1, 1881

By R. C. Emmett, D. A. Dahlstrom

Application of continuous filtration to precipitate dewatering requires not only careful equipment selection, choice of appropriate media, but also close control of precipitation technique itself.

Jan 1, 1961