Search Documents

By Elmer A. Jones

Development work in mines of St. Joseph Lead Co., Southeast Missouri, using trackless loading equipment shows definite advantages: Speed of cleaning, ability to work on steep grades and sharp crosscuts, good later tracking conditions, and possibility of wasting rock in old abandoned stopes. THE Desloge mine is one of a group of mines owned by the St. Joseph Lead Co., in the so-called Lead Belt of Southeast Missouri. It has been operating approximately 40 years producing a daily tonnage ranging from 1600 to 3800, depending on various factors. On an average, the present mine is 300 ft deep with an extreme extent of 2.7 miles by 1.7 miles. Most of the present mining is in the lower horizons of the Bonne Terre dolomite, a fairly soft rock requiring no support except occasional channel iron and roof pins. Due to the contour of the underlying sandstone and porphyry, some development work has been through short stretches of these different formations. In some areas the lower part of the dolomite is quite sandy and generally is considered abrasive. Sizes and Methods of Drifting Have Changed: Development work has, like other phases of mining, changed considerably in the last 20 years, from cleaning by hand to the use of a mechanical method. The conception of a standard drift has also changed. Before the advent of mechanical loading in stopes there were many pieces of main line drift averaging 7 ft high x 9 ft wide. With the coming of the St. Joe shovel the drift was increased to 8 ft high x 10 ft ELMER A. JONES, Member AIME, is Assistant General Mine Superintendent, St. Joseph Lead Co., Bonne Terre, Mo. AIME Columbus Meeting, September 1949. TP 2859 A. Discussion (2 copies) may be sent to Transactions AIME before July 31, 1950. Manuscript received Sept. 16, 1949. wide. Now with the Joy loader and shuttle car, a 9x11 ft drift is coming to be standard size. Methods of cutting drifts have changed considerably over the last few years. Some changes in drilling equipment have been made such as reducing the weight of column, clamp, air feed, and fittings to go with the HC10 Cleveland jackhamer. Other changes have been made in drill steel such as the use of detachable bits; throw-away variety, screw type, and the tungsten-carbide insert bits. Later developments have introduced spiral-welded pipe with victaulic couplings, millisecond exploders, bulky powder, and the use of electric cap lamps. Experimental work is going on continually in various phases of development work, some to be tried and discarded, others gradually to become standard practice. To sum up, the standard method of development now in use at Desloge is as follows: The work is done on a two-shift cycle 7:00 p.m. to 3:00 a.m. and 7:00 a.m. to 3:00 p.m. Two men known as development drillers comprise a crew on each shift. These two men arrive at their work about 7:30 to find a round blasted by the previous shift. After scaling down back and walls they proceed to the cleaning operation, using either a Joy loader and shuttle car, a drag hoist mounted on a slide ramp, or an Eimco Finlay to load into a 21/2 ton mine car. Cleaning may take from 2 to 4 hr depending on conditions such as length of round broken, length of haul, and other variables. After fitting up pipe and setting up columns and drills they are ready to drill a round which should measure 9 ft high x 11 ft wide and break from 5 to 7 ft advance. This may also take from 2 to 3 hr. Then they are ready to charge and

Jan 1, 1951

By L. Bombardieri, H. F. Mills

Iron King mine, producing gold-silver-lead-zinc-ore, is 10 miles east of Prescott, Ariz. At present the 1806 level is being developed. The echelon pat tern of ore deposit continues at depth but is less pronounced, and the orebody is now more or less continuous over 2600 ft of strike length, with widths 5 ft to as high as 26 ft where overlapping of lenses occurs in one section of the mine. Better continuity of ore at depth has encouraged systematic mining and improved plant facilities to offset higher operating costs. With favorable persistence of ore at depth, the three-compartment No. 6 hoisting shaft appeared inadequate to handle increased tonnage from greater depths, and in 1952, a four-compartment steel and concrete shaft was started. This is now at a depth of 1906 ft, and shaft pockets and loading cartridges are being installed on the 1806 level. Ore from the new shaft, hoisted in 5 ½ -ton Jeto bottom dump skips, is dumped into a 500-ton shaft bin, from which it is fed to a 16x30-in. gyratory crusher and conveyed 415 ft through an undersurface concrete gallery to the secondary crusher and conveying system supplying the 900-ton mill. Lead, zinc, and pyrite concentrates are floated, and the flotation tailings are cyanided after desliming. Waste from the new shaft is dumped into a 250-ton surge bin, fed from this bin to a 24-in. conveyor, and discharged into the glory hole above the block cave. The new shaft is served by a double-drum 400-hp hoist used for ore and waste; the No. 6 shaft conveys men and material.

Jul 1, 1956

By M. Cohen, R. J. Teitel

There is considerable interest in beryllium because of its low density (1.84 g per cu cm), high modulus of elasticity (40 X 106 psi), high melting point (1280°C), and special nuclear characteristics. Moreover, it has fair resistance to corrosion and oxidation. However, the purest beryllium known to the authors is relatively brittle at room temperature, and cannot be fabricated readily. The search for improved properties leads naturally to investigations of beryllium alloys and the phase relationships upon which they are based. The present paper is concerned with the alloys of beryllium and iron, primarily from the standpoint of the equilibrium diagram. Iron was selected (1) because of its all-round importance in metallurgy, and (2) because the beryllium-iron system is known to be quite complex. The most recent diagram in the literature is that of Gaev and Sokolov,' and covers only the iron-rich end up to 16 wt pct beryllium. Beryllium markedly restricts the austenitic field, closing the gamma loop at about 0.4 wt pct (3 at. pct). On the other hand, beryllium is soluble in a-ferrite up to a maximum of 7.5 wt pct (34 at. pct) at the eutectic temperature of 1160"C. The eutectic composition lies at 10 wt pct beryllium (42 at. pct) and corresponds to a mixture of or and FeBez (called j3 in the present paper). The solid solubility of beryllium in the a phase decreases with decreasing temperature, and makes precipitation-hardening possible. These findings substantiate the earlier work of Oester-held,2 Wever and Mueller3 and Laissus.4 In addition to the FeBe2 (ß) mentioned above, Misch6 has reported on FeBes, and indicated evidence for another compound containing still more beryllium. A preliminary diagram by Gordon,5 not hitherto published, is given in Fig 1. Besides the phases previously named, there are shown a solid solution of extended range (e), a compound of limited solubility (t), and a high temperature phase (7). Beryllium is designated as 8. The t field contains the compound composition FeBea, and the f phase undoubtedly corresponds to the beryllium-rich compound found by Misch.6 The region around the { phase was proposed by R. J. Teitel based on Gordon's data. The details of the diagram are self-explanatory. It was the unusual complexity of this system that prompted the authors to undertake the present studies. By the same token, more emphasis was placed on the beryllium-rich than the iron-rich end of the diagram. Exprimental Details RAW MATERIALS The beryllium employed in this investigation was one of the purest grades available. Its chemical analysis after vacuum melting is given in Table 1. The metal assayed 99.4 wt pct beryllium. Vacuum melted electrolytic iron of purity shown in Table 1 was the source of iron.

Jan 1, 1950

By J. O. Nelson, C. J. Altstetter

Single crystals of hcp cobalt, 3 mm in diameter and up to 35 cm long, were grown using an electron-beam, zone-melting technique. The martensitic-phase transformation was studied in single-crystalline and polycrystalline specimens by making length-change measurements as a function of temperature under various elastic compressive stresses. Upon thermal cycling, single-crystalline or polycrystalline specimens repeatedly transformed almost entirely on the same variant of close-packed plane provided the maximum temperature did not exceed 600°C. Cycling to 1000°C resulted in transformation on more than one {111} variant. This behavior is termed multivariance. The multivariant transformation occurred very rapidly at an M, temperature 2° to 6°C lower than the M, of a transformation which would result in a single-crystal product. Elastic compressive stresses (up to 253 g per sq mm) tended to lower the A, and raise the M, temperatures, decreasing the width of the temperature vs dilatation hysteresis loop. The transformation habit plane and transformation shear direction of an as-grown single crystal were not grossly affected by elastic compressi?ie stress. This was evidenced by similar dilatations on the temperature us dilatation loops joy specimens with and without compressive stress. A dislocation mechanism is proposed to explain the observed results. IT has been shown that, on heating, cobalt transforms martensitically from the hcp to the fcc phase.' The transformation habit plane is (0001)hcp || (lll)fcc and the transformation shear direction is (1010)hcp || (112)fcc. The transformation involves a shear of 1g°28', which may be achieved by a shearing of a/6(112) of every two planes with respect to the plane beneath, thus changing the ABABAB stacking of hcp to the ABCABC stacking of fcc. Associated with the phase change is a 0.3 x 10"3 contraction in the habit plane and a 4.2 X 10"3 expansion perpendicular to the habit plane resulting in a 3.6 x X volume increase on heating.' On cooling, an identical volume decrease takes place. The temperature at which the fcc phase begins to form on heating (A,) is reported as 430°C, and the temperature at which the hcp phase begins to form on cooling from an elevated temperature (A&) is reported as 390oC1,3 Consequently, temperature vs dilatation plots have the form of a hysteresis loop. If heating or cooling is reversed during a transformation, a smaller hysteresis loop results. Upon heating, the transformation is always complete; whereas, fcc is often retained at room temperature as a metastable phase entrapped in the polycrystal-line hexagonal matrix.1,4,5 Two obstacles in the theory of the allotropic-phase transformation of cobalt have been: 1) a detailed knowledge of the product nucleus, and 2) a plausible method of propagation of the transformation. Bilby,8 christian, 7 and seeger 8,9 have suggested a "pole mechanism" as a means of propagation of partiai dislocations from plane to plane. A pole dislocation and a Shockley partial come together at a node. The a/6(112) Shockley partial rotates about the pole dislocation effecting the transformation shear. The pole dislocation must have a 2a/3(111) screw component which causes extension of the transformed region by two atomic planes with each full rotation of the Shockley partial. Bollmannl0 suggested, on the other hand, that transformation propagation occurs due to the stress fields of intersecting (111)-type stacking faults. As faults intersect, a stress distribution is set up about their intersection which is in turn reduced by the emergence of another fault on the second nearest plane. This process continues with the final result of a complete phase transformation. In view of the similarities between deformation and transformation in cobalt, the effect of stress on the transformation would, hopefully, yield valuable information concerning nucleation and propagation. In the present work single-crystalline and polycrystalline specimen length changes were measured as a function of temperature at various compressive loads. PROCEDURE Several orientations of single crystals of hcp cobalt in lengths up to 25 cm were grown by electron-beam floating zone melting from 99.95 and 99.999 pct, 3-mm-diam cobalt rod as supplied by Johnson

Jan 1, 1964

By B. L. Averbach, Morris Cohen, S. A. Kulin

The martensitic transformation can be initiated by elastic stresses at temperatures above M. in a steel containing 20 pct Ni and 0.5 pct C. Shear strains and normal tensile strains acting on a potential habit plane promote the transformation but compressive strains oppose it. THE strain sensitivity of the martensitic transformation has long been recognized. It is now well known that martensite formation can be induced by plastic deformation at temperatures below, and not too far above, the M, point.' However, the exact role of elastic vs. plastic strains and of the concomitant stresses has proved to be a very elusive matter. Many investigators2-' of the steel hardening reaction have made use of the stresses resulting from volume changes to account for such observations as the existence of retained austenite and its variation across the section of a bar, the change in the amount of retained austenite with quenching rate, and the self-stopping nature of the transformation when the cooling is stopped. The effect of applied strain as an independent variable has been studied in 70 pct Fe-30 pct Ni alloys by Scheil7 and McReynolds.8 Some data are also available for lithium and Li-Mg alloys,9 Cu-Zn,10 Cu-Sn and Cu-A1 alloys," and aus-tenitic stainless steels."-" It has been found that martensite formation can be induced isothermally, even at temperatures above M,, by mechanical deformation of the parent phase. The competitive nature of plastic yielding by slip and by the martensitic reaction has been depicted by Scheil.7 Basically, Scheil postulated that: 1—at temperatures not too far above M, (where austenite is less stable than martensite), a critical resolved shear stress (within the elastic range) is required to promote the transformation to martensite; 2—at and below M,, the austenite lattice becomes mechanically, as well as thermodynamically, unstable and shears over spontaneously into martensite without the application of external stress; and 3—at temperatures sufficiently far above M8, the critical resolved shear stress for martensite formation increases to a level above that required for slip, and plastic flow then supersedes the transformation when external stress is applied. Scheil's concepts were tested by McReyno1ds8 ho found no change in the elastic moduli (measured both statically and dynamically) of 71 pct Fe-29 pct Ni alloys in the vicinity of the M, temperature. Since the moduli did not approach zero or become negative on cooling to M,, it was concluded that the austenite lattice does not become mechanically unstable at M2, as postulated by Scheil. McReynolds also reported that M, is not raised by elastic stresses. Accordingly, plastic deformation was considered to stimulate the transformation by generating martensite nuclei in the distorted regions of the parent phase. The above issues with regard to the role of applied stress require clarification, if a basic understanding of the martensitic transformation is to be obtained. For example, in the reaction-path theory,'"," it is postulated that strain embryos exist in the austenite that provide part of the activation energy for the nucleation process. These embryos are visualized to be regions of localized strain in which the atoms in the austenite lattice are displaced part way along the path to their ultimate positions in the martensite. Consequently, it would

Jan 1, 1953

By H. A. Lequear, J. D. Lubahn

A sudden change from one constant strain rate to another during a tensile test causes an unusual transient in aluminum alloy 61ST. A sudden change from one constant stress to another during a creep test does not produce an unusual transient in this material. A specially devised test shows that the nature of the previous steady-state conditions, which the sudden change disturbs, is one of the factors affecting the transient behavior. Some of the observations may be explained in terms of strain aging. USUALLY a sudden change during a tensile test from one constant strain rate to another causes a small, abrupt vertical shift from one stress-strain curve to another, parallel one. This behavior is apparently characteristic of all metals at very low temperatures and of many metals for wide ranges of temperature. It is illustrated in Fig. 1 for some early data on 61ST tested at — 195oC, and in Fig. 2 for some recent data on copper at room temperature. The greater accuracy of the results of Fig. 2 over previous ones' is due to the equipment shown in Fig. 3. Three levers apply the bulk of the load, while the changes in the small remainder load are indicated sensitively by a low capacity load scale. Refs. 2 and 3 describe the recording equipment. A test like those in Figs. 1 and 2 provides the information necessary to determine the rate sensitizrity, n,4 of the metal. ( a log s ) ? log s n = ------------------------ ----------------------------= ( a logs e, ? log e logS2-logS1 log S2/S1 log i2 — log e1 log e2/e1 where S equals stress: e is logarithmic strain or natural logarithm of (final gage length/initial gage length);" i is strain rate or de/dt: and n is rate sensitivity, rate of change of log stress with log strain rate at a given strain, or (a log S/a log i),. Normally, the rate sensitivity, n, is positive, which means that an increase in stress causes an increase in rate. However, certain exceptions, attributed to strain aging,5 have been observed. Fig. 2 indicates how rate sensitivity values are derived from the measurements. Table I summarizes the rate sensitivity values derivable from Fig. 1. In contrast to the behavior of copper in Fig. 2, the aluminum alloy 61ST, which strain ages when tested near room temperature, exhibits an unusual transient when the strain rate is suddenly changed,' as shown in Fig. 4. Initially, there is a comparatively sudden vertical shift of the stress-strain curve in a direction corresponding to the rate change, but then the curve gradually shifts back again. The initial shift is not as sudden as might be expected, because the testing machine is unable to achieve the impressed rate change instantaneously, as illustrated in Fig. 2. The behavior shown in Fig. 4 will be referred to as a tensile transient, the word tensile implying that the behavior was observed in a tension type of test. The corresponding test, where the strain rate is maintained constant except for the sudden change, will be called a tensile transient test. A creep transient, by contrast, will be defined as a temporarily abnormal behavior in a creep transient test, where there is a sudden change from one constant load to another.' In Fig. 4, a naive look at the gradually decreasing and then increasing load after a sudden rate incre-

Jan 1, 1957

By F. Clerf

Blast-furnace practice in France is determined more or less by the character of the ores used. Some French ores are siliceous and others are calcareous, therefore by proper burdening a self-fluxing mix can be used. This is not always done, as, for instance, at the Caen furnaces of the Société Métallurgique de Normandie, where the Soumont ore of Normandy is used, which is a carbonate. This ore is crushed and calcined at the mines, yielding a product that is porous and well sized for blast-furnace consumption. The lines of the Caen furnaces are given in Fig. 1. Originally these furnaces had 16 tuyeres; six are plucked and these tuyeres are set in the lower part of the bosh. Operating data on these furnaces are given in Table 1. Table 1.—Operating Data, Caen Furnaces Kg. Lb. Blast-furnace burden per ton of iron: Soumont ore....................................... 200&2100 (44004650) Limestone...................................... 900-1000 (2000-2200) Basic Bessemer slag (bearing phosphorus).............. 100 (220) Scale.............................................. 35 (77) Manganese ores.................................... Coke.............................................. 1100-1200 (2420-2640) Coke analysis: Ash, per cent............. 9.5 H2O, per cent............. 4.0-10.0 Flue dust (approx.), kg. per metric ton.... 200 (440 lb.) Blast volume, cu. m. per hr.............. 83,000 (49,000 cu. ft. per min.) Preesure, lb............................ 12 Blast heat, deg. C....................... 650 (1200" F.) Top temperature, deg. C................ 250 (445O F.) Top-gas analysis, per cent............... CO2 9.3 CO 30.3 O2 0.3 H2 3.0 Production per 24 hr. about 510 tons. MINETTE ORES The most important ore deposits in France are in the west of Lorraine. They are called the "minette" ores and are of two classes-—siliceous and

Jan 1, 1937

Executive Committee, Board of Directors Howard C Pyle, Chairman, J L Gillson, Vice¬Chairman, A W Thornton, Elmer A Jones, Augustus B Kinzel Finance Committee, Board of Directors J S Vanick, Chairman, John P Hammond, J W Woomer Investments Gail F Moulton, '60, Chairman, Andrew Fletcher, '62, John M Lovejoy, '61, C R Dodson, ex off as AIME Treasurer, J S Vanick, ex off as Chairman of Finance Committee Endowment Andrew Fletcher, Chairman, N G Alford, W J Coulter, Harold Decker, J V N Dorr, R B Gilmore, J B Haffner, Kenneth Hill, 0 H Johnson, J D MacKenzie, D H McLaughlin, J R McMillan, W S Morris, L F Reinartz, H DeWitt Smith, Wilfred Sykes, J R Suman, C E Weed Honorary Memberships C E Reistle, Jr, '60, Chairman, Grover J Holt, '61, Augustus B Kmzel, '62, (ex off as Past Presidents of AIME) M L Haider, '60, D H McLaughlin, '61, John M Lovejoy, '62, L F Reinartz, '63, Howard C Pyle, ex off as President of AIME

Jan 1, 1959

By F. J. Plecity, J. T. Michalak, W. C. Leslie

W. M. Williams (McGill University)-The authors are to be congratulated on completing this detailed investigation of recrystallization behavior. The present writer has recently completed some research at the University of Toronto on the recrystallization and grain growth behavior of a number of "pure" irons, and he would like to take issue with the authors' contention that recrystallization cannot be followed by means of hardness measurements. Two series of specimens of Ferrovac E, a com- mercially available iron, were annealed to complete recrystallization at 525" and 620" C, measurements being made both of Rockwell hardness and of volume percent recrystallized as a function of annealing time. Good correlation was found between these two quantities and, following the earlier practice of Cook and Richards for copper, hardness measurements were used in an extensive investigation of recrystallization. No anomalous behavior was observed as a result of this practice. Specimens which showed complete softening always showed, (metallographically and by X-rays), completely re-crystallized structures. These observations do not, of course, detract in the least from the results of the work under discus-

Jan 1, 1962

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872-1874 A L HOLLEY1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 - 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882 ROBERY W HUNT 1883 JAMES C, BAYLES 1884-1885 ROBERT H RICHARDS 1886 THOMAS EGLESTON 1887

Jan 1, 1923

By C. E. Mills

The Verde mining district is in Yavapai County, in north-central Arizona. Jerome, the principal town, has a population of 6000 and the two important mines of the district—the United Verde and the United Verde Extension—lie almost within its limits. Perched high on the southwest side of the Verde valley, at elevations of 4800 and 5500 ft. (1463 and 1676 m.) respectively, both mines have long tunnels from their lower levels through which the ore is hauled to the smelters. Clarkdale, the smelter town for the United Verde mines, lies in the Verde valley 4.1 miles (6.5 km.) distant in an air line from Jerome and at an elevation of 3560 ft. The two towns are connected by the standard-gage railroad of the Verde Tunnel and Smelter R. R., a subsidiary of the United Verde Copper Co. This road is 11 miles long and has a compensated grade of 4 per cent. At Clarkdale it connects with the Verde valley branch of the Santa Fe railroad. Clemenceau, the smelter town for the United Verde Extension mine, lies 3.5 miles (5.8 km.) in a southeasterly direction from Clarkdale, at an elevation of 3420 ft. It is connected to the Verde Valley branch of the Santa Fe railroad at Clarkdale by the Arizona Extension R. R., a subsidiary of the United Verde Extension Mining Co. The portal of the haulage tunnel, at an elevation of 3757.5 ft., is also connected with the smelter town by 4 miles of standard-gage track belonging to the same company. In the vicinity of Jerome, the great southern escarpment of the Arizona plateau forms the northeast side of the Verde valley. The general level of this escarpment, or "rim" as it is called, is about 4000 ft. above the Verde River. A corresponding elevation is reached only by the highest peaks of the Black Hills, which bound the valley to the southwest. Two lava-capped mesas, known as "Mingus" and "Woodchute mountains," form the culmination of the Black Hills. That part of the Old Black Hills mining district which lies between their crests and the Verde River is now known as the Jerome, or Verde, mining district. If the smelter towns are not included, a strip about 7 miles long by 3 miles (11 by 5 km.) wide, embraces practically all of the properties belonging to the Jerome district. T-bis strip lies parallel to and along the side of the Verde valley from First View, 2 miles northwest from Jerome, to the

Jan 1, 1925

By G. L. Boxer, C. B. Smith, W. J. Atkinson

Since the inception of the Ashton (formerly Kalumburu) Joint Venture in 1972 the parties have expended $24 million in exploration for diamonds in the Kimberley region. This has resulted in the discovery of the currently subeconomic Ellendale deposits in 1976/77 and the economic Argyle - Smoke Creek Deposits in 1979/80. In addition to Argyle and Ellendale, some 90 kimberlitic and lamproitic bodies have been discovered grouped broadly into three provinces, on the west, east and north margins of the Kimberley block. These bodies range in size from dyke-like features less than 1 m (3 ft) in width to pipes with a surface area of 128 ha (316 acres). The bodies with larger surface area are volcanic crater deposits, infilled with air-fall and water deposited tuffs and epiclastic sediments. Diamond content ranges from trace to economic concentrations. The exploration discoveries were facilitated by early recognition that the petrography, mineralogy and chemistry of the diatremes varied from the classical kimberlites of Kimberley, South Africa, to unusual more highly fractionated, alkaline, silicic varieties having affinities with leucite-lamproite. Indirect methods of exploration were used, primary reconnaissance work being stream gravel sampling for kimberlitic indicator minerals. Evaluation showed Ellendale diamonds are 90% gem and near gem, but the low grades and tonnage render the deposits unpayable at today's diamond prices. After discovery in late 1979 and completion of a feasibility study by the end of 1982, evaluation studies proved Argyle to be economic. Alluvial diamond mining commenced in 1983 producing 6.2 million carats (Mct) that year, 60% being of industrial quality. Open-pit mining of the AK1 lamproite should start in 198511986 at a rate of 3 million t/a (33 million stpy) and produce 25 Mct/a, making this mine, and Australia, the world's largest producer of diamonds by weight. The revenue from diamond deposits is a function of the grade and the value of the diamonds. The grade is the product of the frequency of occurrence of the diamonds (stone density) and the mean stone size; the value of the stones is strongly related to their size distribution. During evaluation of the West Australian deposits, the diamond distribution was found to vary markedly in stone density and stone size. These variations corresponded with changes in the rock type hosting the mineralization. As a consequence, geological mapping of individual lamproites within the multiple vents and careful monitoring of the diamond distribution became an important part of the evaluation work. Similar variations in stone size and frequency were found to accord with separate alluvial terraces and fan gravels derived by erosion from the Argyle AK1 lamproite.

Jan 1, 1985

By Horace R. Graham

CHEMICAL nitrogen and the "nitrates" of commercial significance are derived mainly from three basic sources: (1) the natural deposits in the form of nitrate-bearing earth and clay, which, being largely water-soluble, can exist only in the most arid portions of the earth; (2) coal, which yields not only nitrogen but also the additional by-product hydrogen required for the synthesis of ammonia and its compounds; (3) the atmospheric air, which contains 75.5 pct by weight of pure nitrogen gas. NATURAL NITRATE DEPOSITS Occurrence Although natural nitrate deposits consisting principally of the salts of sodium and potassium have been reported in Egypt, South Africa, Mexico, Argentina, Colombia, Peru and the USA, the only known natural nitrate resources of commercial importance are the vast deposits found in the Atacama, Tarapaca and Antofagasta regions of northern Chile, lying in a narrow strip 10 to 50 miles wide and roughly 450 miles long, between latitudes [19O] and [26OS]. In addition to yielding nitrates of sodium and potassium, these deposits are the source of the major portion of the world's supply of iodine. The nitrate-bearing ores known in Chile as caliche are variable in composition and may contain from 5 to 30 pct each of nitrate, chloride and sulphate. While the deposits are present chiefly in the form of the sodium salt, potassium, magnesium and calcium also occur in percent- ages from 0.1 to 5; usually as double salts with sulphate, which are but slightly soluble in nitrate leach solutions. These double salts are bloedite(Na2S04.MgS04.4H,0), glauberite (Na2S04.CaS04), polyhalite (K2SO4.- MgS04.2CaS04.2H20). Some deposits contain up to30 pct of their ni-

Jan 1, 1949

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872-1874 A L HOLLEY1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 - 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882 ROBERY W HUNT 1883 JAMES C, BAYLES 1884-1885 ROBERT H RICHARDS 1886 THOMAS EGLESTON 1887

Jan 1, 1923

By Eugene A. Alexandrov

The Minister of Geology of the Soviet Union P.Ya. Antropov, recently visited China and claims that this country occupies one of the foremost places in the world in reserves of tin, tungsten, molybdenum, antimony, iron ore, coal, and phosphates. Occurrences of economic value of chromite, nickel, gold, beryllium, tantalum, niobium, rare earths, and asbestos have also been reported. MINERAL RESOURCES Coal: The inferred reserves of coal are estimated at at 1,500 billion tons. A considerable part of the coal reserves is represented by coking coal, 80% of which is bituminous. Thicknesses of coal seams range up to 150 ft in the principal deposits located in northern and northeastern China. The total output of coal in 1958, 270 million tons, was produced by an army of 20 million people mainly in small mines operated by the agricultural communes. Modern hydraulic mining is applied besides primitive, obsolete methods and equipment

Jan 3, 1960

By David Segura

THE Huitzuco mercury deposits have been described by C. W. Vaupell,1 therefore the general information such as location, history, production, etc. will not be repeated here. The present owners acquired the property when the deep levels of the Cruz mine were flooded, and it was believed that a relatively large tonnage of low-grade ore and fills would be encountered in the flooded section, because of the early mining methods used in the Cruz mine. The mine was partly unwatered and about 187,000 tons of fills was pit-sampled in the San Cayetano stope. These fills average 2.4 kg. Hg per ton. During the period of maximum production at Huitzuco, the ores were sorted in the mine and cobbed into 3-in. pieces, which were treated in Scott furnaces. Large pieces of raw ore are found in the sinter, and it is indicated that both recovery and costs were not very satisfactory. Recent practice has been to treat the ores in closed retorts made of 10-in. pipes. Because of the presence of combined antimony in the mineral livingstonite (HgS.2Sb2S3) and considerable native sulphur, little or no metallic mercury is recovered in the condensers and a second retorting of the condenser muds is necessary. This makes the treatment of the ores expensive and tends to low recoveries of mercury. The principal costs of retorting are, in their relative order: (1) fuel, (2) low recovery of mercury, (3) replacement of retort pipes, (4) labor. METHODS TESTED Three series of experiments have been made, with the object of reducing the costs of recovering mercury and antimony from the ores, by: (1) wet metallurgical methods, (2) bulk roasting in large mechanical furnaces, (3) concentration to reduce the bulk to be followed by roasting in some mechanical furnace. The wet metallurgical methods did not appear feasible because of the high cost of the alkaline solvents used, and investigations of these were not carried beyond the preliminary stage.

Jan 1, 1938

By O. R. Morris, G. L. Hawkes

A galvanic cell, using as electrolyte a fused salt solution of calcium carbide and as electrodes carbon and a Fe-C alloy of known composition, has been set up to study the thermodynamics of Fe-C alloys in the temperature rmzge 800" to 1000°C. Time independence and reproducibility of the cell electromotive force were taken as evidence of the reversible behavior of the cell. Carbon was believed to be present in the electrolyte as the so-called acetylide ion, C;-. The plots of the cell electromotive force us temperature for a specific alloy composition were straight lines within the limits of experimental error. The average Partial molar enthalpy of carbon in iron relative to pure carbon was found to be +10,610 i 93 cal per g-atom C. Thermodynamic analysis of the data has led to the following equation for the carbon activity, ac, based upon pure carbon as the standard state: In ac = In Zc + 10,560/RT + (10.02 + 77O/T)ZC - 2.350 where ZC is the lattice ratio [nC/(nF, - nc )] and T is the absolute temperature. This equalion gives carbon activity values generally slightly lower than those from gas equilibration studies reported in the literature. METAL LOGRAPHIC examination of a polished cross section of the steel anode used in the electrolysis studies of fused salt solutions of calcium carbide by Morris and Harry revealed extensive carburization of the steel by the electrodeposited carbon. This carburization was reflected in the variability, with time, of the applied potential to the electrolysis cell, necessary to maintain a constant current density at the electrodes. This observation suggested the setting up of a galvanic cell of the "alloy concentration" type to study the thermodynamics of some metal-carbon alloys. Cells of this general type have been widely used for the study of alloy systems.2 In view of the availability of published data in respect of the austenite phase of the Fe-C system, it was decided to carry out measurements upon these alloys before proceeding to studies of less well documented systems. The galvanic cell may be written: where [C] is carbon dissolved in iron. The electrolyte was a fused salt solution of calcium carbide, containing some 5 to 10 mol pct of carbide. The cell reaction is believed to be: C(s)-[CI [I1 Carbon forms an interstitial solid solution in iron, with the atoms located in the octahedral interstices. In the fcc crystal structure of austenite there is one octahedral interstice per iron atom. Thus, the lattice ratio, ZC, shown by Gurney3 to be the fundamental concentration parameter in the context of interstitial solutions, is given by: where nc and nFe are the number of carbon and iron atoms, respectively. chipman4 has recently shown empirically the advantages of using this concentration parameter instead of the more usual atom ratio or atom fraction. The cell electromotive force, E, assuming reversible behavior, is related to the carbon potential or the partial molar free energy of carbon in the solid solution relative to pure carbon at the same temperature and pressure, GP at the composition ZC, by the equation: where z is the carbide ion valency and F is the Faraday constant. An activity of carbon, ac, in the solution relative to the value of unity assigned to pure carbon, and an activity coefficient, qC , are defined such that: where R is the gas constant and T the absolute temperature. GF is further related to the relative partial molar enthalpy Hm, and the temperature coefficient of the cell electromotive force, (aE/aT)Zc, by the equations: Measurement of the cell electromotive force thus enables calculation of the relative partial molar thermodynamic properties of carbon in iron, if z is known. At E = 0, the solid solution is in equilibrium with pure carbon. More convenient for many purposes is the standard state based upon the infinitely dilute solution, Henry's law. The relationship between the activity coefficient of carbon based upon this standard state, and that based upon the pure carbon standard state, qC , may be obtained by considering the free energy of transfer of carbon from the latter standard state to the former. The relationship is: where +:H is the activity coefficient of carbon in the hypothetical standard state based on a reference of

Jan 1, 1969

By T. A. Read, H. K. Birnbaum

Deformation of AuCd alloys having the 8 (orthorhombic) and (3" (tetragonal) structures occurs by the stress induced motion of twin boutdaries. A restoring force acts on displaced twin boutdaries as a result of internal energy increases in the volume through which the boundaries are displaced. The phenomonology of the twin boundary motion is described and a mechanism for twin boundary motion and the restoring force is proposed. A time-dependent stabilization behavior of the twin boundaries, which is observed after the twins are formed by the diffusionless phase transformations, is described. THE AuCd 8 phase (ordered bcc structure) exhibits a transformation to a phase having an orthorhombic structure, 8' (space group D'), for compositions in the vicinity of 47.5 at. pct Cd and to a phase having a tetragonal structure, 8" (point group 4/m, m,m), for compositions in the vicinity 50.0 at. pct Cd. Both transformations are diffusionless, occur on cooling at 60" and 30OC, respectively, and are crystallo-graphically reversible.' They are accompanied by an inhomogeneous deformation which was observed to be twinning in the low-temperature phase. 3'4 The transformations may occur by a "single interface" or by "multiple interfaces."5'6 In the "single interface" transformation, the twinned product phase consisted of two twin orientations as shown in Fig. 1. In the multiple interface transformation the product phase contained "domains" each of which contained two twin orientations, Fig. 2. Deformation of specimens containing transformation twins was achieved by motion of the twin boundaries. Releasing the applied stress resulted in the displaced twin boundaries returning towards their initial positions. This "pseudo-elastic" behavior of the boundaries varied with time after the formation of the twin boundaries by the transformation.

Jan 1, 1961

By E. J. Krokroskia

Fletcher Mill is located in the southern part of the New Lead Belt in Southeastern Missouri, in the northwestern part of Reynolds County. Shaft sinking began in July, 1964. The mill went on stream in February, 1967, and reached the designed rate of 5,000 tons per day in July, 1968. The ore occurs approximately 1,000 feet below the surface as disseminated deposits of galena, sphalerite and chalcopyrite. There is no oxidation within the ore body and dissemination is not fine enough to present liberation problems with a normal grind. Mining is by the room and pillar method with rubber-tired diesel- propelled drilling and loading equipment. The ore is dumped through a 27-inch square grizzly into a 5,000-ton pocket. The underground primary crusher is automatically fed by a vibrating feeder and discharges directly into skip measuring bins. Hoisting is automatic, in balance, with 8. 5-ton skips dumping into a 1,000-ton mill bin. MILL The concentrator is a 5, 000 tons-per-day single section plant equipped to produce lead, zinc and copper concentrates. Contained under 35, 347 square feet of roof, without fine ore storage or remote crushing, and with sufficient automation to be operated by one man, the plant is compact, unique, and efficient in operation. The design

Jan 1, 1970

By R. E. Ford, P. Tarassoff, P. H. Jennings

Copper oxide ore may be leached at all sizes from run-of-mine down to pulp, and consideration must be given to all available methods in determining the most economical one. Heap leaching was evaluated in a pilot plant at Gaspe Copper Mines, Ltd. which was designed to simultaneously leach two 1200-ton dumps of ore. The plant was operated for two years, in part under severe winter conditions. Two modes of leaching were investigated: acid leaching in which sulfuric acid was added externally to the leach solution, and pyritic leaching in which pyrite concentrate was added to the dump and acid was generated in situ by bacterial action. The pilot plant operation is described, and the results are compared with laboratory data obtained in 6-in.-diam columns. It is concluded that pyritic leaching offers certain operating advantages over acid leaching when copper is recovered by cementation in that iron buildup in the solution is prevented.

Jan 1, 1974