Search Documents

By Leon W. Dupuy

SUPPLEMENT THESE tables should accompany Figs 6, 7, 8, 9 and 10, respectively. To follow Fig 6: TABLE 2[a]-Drill Rod [ ] To follow Fig 7: TABLE 3-Rod Coupling [ ]

Jan 1, 1947

By R. L. Dietrich

Magnesium alloy sheet has less ability to accept bending at room temperature than most of the heavier metals. In work designed to improve the bend properties, the preferred orientation of the sheet is of major importance as it is in all studies of the properties of wrought magnesium products. When rolled into sheet, all of the common magnesium alloys form an orientation texture having the basal (002) planes approaching parallel to the surface of the sheet. This texture is only slightly affected by annealing. Magnesium single crystals are highly anisotropic, and, as might be expected, so are magnesium alloy wrought products in which a strong preferred orientation is developed. It is therefore not surprising that bend properties are affected by orientation. Ansel and Betterton1 reported that the orientation of AZ3lXt sheet varies from surface to center and that bend properties are improved by etching away the sharply oriented material at the surface of the sheet to reach the more broadly oriented structure below. This paper covers a study of that orientation, either during the rolling process or by treatment of the finished sheet, in an effort to improve the bend properties and toughness of sheet. Literature The orientation texture of magnesium and magnesium alloy sheet has been studied extensively. Early determinations2 showed that pure magnesium sheet has a preferred orientation in which the basal planes are parallel to the sheet surface within very narrow limits. J. C. hIcDonald3 and J. D. Hanawalt4 reported that sheet containing a small amount of calcium develops a "double" texture, that is, the majority of the basal planes are a few degrees from parallel to the surface and there is a noticeable vacancy at the parallel position. Bakarian5 made careful quantitative pole figures of both pure magnesium sheet and MI alloy SEPTEMBER 1949 sheet which show these features. In all of these studies, however, the orientation was determined by transmission methods in which the resulting pattern is an average through the thickness of the sheet. The tendency of wrought metal to exhibit a different orientation at the surface from that in the center has been reported by many investigators. G. von Vargha and G. Wasserman6 found that with copper, aluminum, iron, and brass the textures of rolled compared to drawn wires were the same at the center but differed markedly at the surface. It was also reported by investigators7 that the orientation of rolled aluminum varies from surface to center. Har-greaves8 found that the surface texture of AM503 (magnesium alloy similar to MI) sheet was different from the center texture. It is reported by Edmunds and Fuller9 that zinc alloy sheet sometimes had a thin layer at the surface with a strong orientation of the basal planes parallel to the surface, which, if present, impaired the bend properties of the sheet. Part1 Surface Orientation ofMag- nesium Alloy Sheet and the Effect on Properties Attempts to correlate the bend properties of magnesium alloy sheet with tension ductility over short gauge lengths proved unsuccessful and the subsequent investigation showed that nonuniformity in orientation is a con- tributing factor as the properties of the surface material have a much more important effect in bending than in tension. A program to study the relationship between surface orientation at the surface and bend properties was then undertaken. First, the effect of etching away the surface of sheet on the bend properties and the orientations at the various depths were studied. Sheet samples of M1, AZ31X, and AZ61X were etched in dilute nitric acid to remove the surface material for various depths to 0.015 in. As may be seen in Table 1, the minimum bend radius improved considerably as the surface layers were etched away but it was necessary to etch the sheet quite deeply, much more so than was found necessary by Edmunds and Fuller9 on zinc sheet. It is also apparent that the amount of etching required is a function of the sheet thickness. In all of this work, radii were measured as R/t, the radius divided by the sheet thickness, in order to eliminate the effect of the reduction in sheet thickness produced by the etching. To determine the orientation texture of the sheet, X ray reflection patterns were taken using copper radiation with the bearn striking the specimen at an angle of 17' to the surface, which is the Bragg angle for the (002) planes of magnesium. Two exposures were made of each specimen, one with the beam perpendicular to the rolling direction and the other with the beam parallel to the rolling direction. The symmetry of the preferred orientation in magnesium sheet is such that these two photographs gave an approximation of the pole figure sufficiently accurate for qualitative work and it was not thought worthwhile to make complete pole figures. These X ray patterns show that the orientation has a much narrower spread at the original surface of the sheet than below the surface. The narrow spread is found in sheet having the majority of the basal planes (002) parallel to the surface, and since this is an unfavorable position for slip, it is

Jan 1, 1950

By Selma Hermann

For the past century, the so-called aluminum bronzes have been assuming a role of ever-increasing importance in the metallurgical field. The last quarter of that century has marked many efforts to find alloying elements that would alleviate some of the undesirable qualities of the aluminum bronzes-for example, the heterogeneity of the alpha solid solution and the extreme hardness of the beta. Much of this work, however, has been rather haphazard-compositions and heat treatment are usually so much at variance as to make comparison impossible. It is the object of this research to study the effect of certain percentages of common alloying elements on aluminum bronzes of analogous compositions and heat treatments. It is hoped that the material gathered here will at least serve as a basis for further systematic study.

Jan 1, 1930

Jan 1, 1892

By Thomas Fraser, David R. Mitchell

THE primary purpose of the loading plant is to transfer the finished product from the preparation machines to the railroad car, truck, or barge in which it is to go to market. Secondary purposes of the loading plant are: to prevent excessive degradation of sizes during loading, to reduce segregation as much as possible, and to prevent excessive quantities of very good or off-grade coal from entering any one car. Nonuniformity of consignments is one of the chief sources of com- plaints by consumers and coal merchants. A properly designed loading plant will do much to reduce complaints and ensure uniformity, not only from shipment to shipment but also in each individual consignment along the length of the car and in cross section. DEGRADATION IN STORAGE, LOADING AND SHIPMENT The object in loading is not only to handle the coal without breakage and segregation, but also to produce a well-trimmed load that will ride to its destination without spillage or breakage en route. The small sizes present in a car of prepared coal as received by the purchaser consist of: missed small sizes not screened out in the preparation plant, breakage during loading, and breakage caused by handling en route. For domestic sizes of anthracite shipped from the Pennsylvania anthracite field to Atlantic coast cities, the dealers' loss because of break- age in loading and shipment amounts to from 2 to 5 per cent and for anthracite shipped to Middle West cities, the loss is 8 to 9 per cent. This difference is in part because dealers in the Middle West rescreen their coal more thoroughly than is usual in the East. One dealer handling Illinois No. 6 coal shipped from southern Illinois mines to Chicago reports an average size loss of 10 per cent when lump coal is unloaded with a fork. This runs as low as 5 per cent for carefully loaded coal and as high as 15 per cent for carelessly loaded coal.

Jan 1, 1943

By C. Cronquist

Since April, 1962, Shell Oil Co. has operated a peripheral line-drive waterflood of the 10.750-ft lower Tuscaloosa (Cretaceous) Denkman sand in the Little Creek field. Located in southwestern Mississippi in the lower Tuscaloosa trend, the field was discovered by Shell in Jan., 1958. Among the largest in the trend, the accumulation is controlled stratigraphically and occurs in an extensive series of alluvial-point bar deposits across a nose that dips gently to the south. The crude oil is 39" API gravity and was highly undersaturated at initial conditions. Early production behavior indicated a depletion drive with slight water influx; primary recovery wm estimated to be 25 million bbl, or 24.5 percent of stock-tank oil originally in place. A.s a result of a favorable mobility ratio and remarkably uniform rock properties, the volumetric sweep eficiency in the waterflood has exceeded 90 percent. Despite the high connate water saturation (56 percent), the displacement efficiency by water injection has been quite efficient, contrary to traditional concepts. Based on observed field flood-out performance, ultimate recovery is calculated to be 46 million bbl. As anticipated, the production rate began declining during 1964 due to a continu ing reducrion in the number of producing wells as flood fronts advanced across the field. Cumulative recovery as of Jan., 1968, was 44.8 million bbl; waterflood operations ~hould be complete by 1970. Introduction Most waterfloods described in reservoir engineering literature involve pattern operations, the most common of which is the five-spot pattern. Only occasiona'lly are linear drives described, even though there probably are increasing numbers being put into operation. Increasing use of linear floods may reflect the accelerating trend towards early application of fluid-injection programs when linear drives are more efficient, as was the case at Little Creek. However. the Little Creek operation is unusual in several respects. It is one of a few successful waterfloods conducted in sands with connate water saturations approaching 60 percent, and it is among the deepest successful water-floods being operated anywhere. Development The Little Creek field was discovered in Jan., 1958, in the lower Tuscaloosa trend in southwestern Mississippi (Fig. 1). The discovery well, Shell-Lemann No. 1, was drilled on a seismic closure about 2 miles southeast of lower Tuscaloosa production at Sweetwater. The well was completed in the Denkman sand at 10,752 ft, and on initial potential it flowed 588 BOPD of 39" API crude on a %+-in. choke; psi was 730 and GOR was 442:l. Development proceeded rapidly on 40-acre spacing, and by the end of 1958 the field was producing approximately 9,100 B/D from 56 wells. Almost all this production came from the northern half of the field. The southern part was discovered in Nov., 1958, at a location almost 2 miles from previously established production. Subsequent drilling established an apparent conneotion about half a mile wide between the twd areas. Development of the field was practically complete by 1961 with the drilling of 155 producers and 35 dry holes. Some early wells were completed open hole but moslt are completed with casing cemented through the productive interval and perforated for production. Geology The lower Tuscaloosa structure in this area is a north-south nose with maximum dips of about 2" on the flanks. There is no discernible faulting at the producing horizon. Productive limits of the field are shown in Fig. 2, which is contoured on a marker just above the main productive zone. A common water level at 10,415 ft subsea was logged at both the northwest and southeast ends of the field. There is a gross oil column of nearly 100 ft (Fig. 2). Since there is less than 40 ft of closure, it is apparent that bhe accumubtion is controlled stratigraphically, being limited by a sand pinch-out across the creslt of the nose. The total produc-

Jan 1, 1969

By James F. Kemp

The iron ores of southeastern Cuba present a subject of exceptional geological interest. Their relations to the inclosing rocks are varied and in some cases unusual. The problem of their geological origin is not a simple one and for this reason has occasioned some divergence of views among previous observers. Profiting, however, by these earlier studies and by more detailed field and laboratory observations as well as by the experience of added years of mining, much more satisfactory descriptions and interpretations can now be prepared. Previous Work In 1884, interest in the southeastern coast of Cuba became active among the consumers of iron ore along the Atlantic seaboard of the United States. Active development was undertaken by the Juragua Iron Co., Ltd., a corporation affiliated with the Bethlehem Steel Co., and the Pennsylvania Steel Co. The property of the Juragua company, which is situated about 15 miles east of Santiago, was studied in June and July, 1884, by Dr. James P. Kimball, at the time Professor of Economic Geology in Lehigh University and one of the best known of American mining geologists. Dr. Kimball published on his return two papers, the first important descriptions which we have of the local geology.1 It is

Jan 1, 1916

By Thomas Fraser, David R. Mitchell

THE primary purpose of the loading plant is to transfer the finished product from the preparation machines to the railroad car, truck, or barge in which it is to go to market. Secondary purposes of the loading plant are: to prevent excessive degradation of sizes during loading, to reduce segregation as much as possible, and to prevent excessive quantities of very good or off-grade coal from entering any one car. Nonuniformity of consignments is one of the chief sources of com- plaints by consumers and coal merchants. A properly designed loading plant will do much to reduce complaints and ensure uniformity, not only from shipment to shipment but also in each individual consignment along the length of the car and in cross section. DEGRADATION IN STORAGE, LOADING AND SHIPMENT The object in loading is not only to handle the coal without breakage and segregation, but also to produce a well-trimmed load that will ride to its destination without spillage or breakage en route. The small sizes present in a car of prepared coal as received by the purchaser consist-of: missed small sizes not screened out in the preparation plant, breakage during loading, and breakage caused by handling en route. For domestic sizes of anthracite shipped from the Pennsylvania anthracite field to Atlantic coast cities, the dealers' lass because of breakage in loading and shipment amounts to from 2 to 5 per cent and for anthracite shipped to Middle West cities, the loss is 8 to 9 per cent. This difference is in part because dealers in the Middle West rescreen their coal more thoroughly than is usual in the East. One dealer handling Illinois No. 6 coal shipped from southern Illinois mines to Chicago reports an average size loss of 10 per cent when lump coal is unloaded with a fork. This runs as low as 5 per cent for carefully loaded coal and as high as 15 per cent for carelessly loaded coal.

Jan 1, 1943

By A. M. Gaudin

THIS paper presents, with the help of colored photomicrographs, the new method of mineral identification termed "selective iridescent filming." This method pertains to the field of determinative mineralogy, which it provides with tools for: (1) phase identification, (2) solid solution analysis. The method should be particularly useful in the applied fields of: (1) paragenesis of ore deposits, (2) mineral dressing, (3) mineral synthesis and study of phase equilibria.

Jan 1, 1938

By Clarence S. Ross

INTRODUCTION THIS chapter on the rô1e of physical-chemical processes in ore deposition presents unusual difficulties because it attempts to discuss the theory of processes that are very imperfectly under- stood, but which are among the most fundamental problems now before the student of ore formation. It is generally believed that a great variety of ore deposits are in some way derived from igneous rocks; but we desire to know the mechanism of their splitting off from the parent magma, the physical and chemical character of the material that acts as a medium for transfer from magma to the point of deposition, the manner of deposition, and the methods of replacement and removal of the invaded rocks. This problem is difficult for the field geologist because it concerns forces that for the most part have long since ceased to act. It involves a complex system of which the time for completion extends from the first development of the parent magma through its intrusion, its slow cooling and crystallization, and the final escape of its last residuum, a time probably represented by millions of years. In space the processes extend from profound depths of the abyssal magma which can never be directly observed, through the horizons characterizing deep-seated igneous rocks and ore deposits; those formed at moderate depths; and ends with surficial ones and surface thermal springs. The geologist usually can study the effect at but one of these horizons: he must attempt to fit his puzzle together while seeing but a few parts at a time. Thus he must deal with many isolated phenomena, as if they were the result of many physical and chemical systems; when in fact his problem involves a single exceedingly complex system, and will only be understood when that entire complex system is understood. The geophysicist is handicapped because he must attempt to interpret an extraordinary complex system, involving physical and chemical conditions which he can never hope to duplicate fully, through the study of many exceedingly simple systems.

Jan 1, 1933

By J. L. LeBlanc, R. L. Lewis

This study presents an analysis of annular backpressure variations associated with controlled gas kicks and their pronounced effect on casing .strings and exposed under lying formations. A mathematical model describing the volumetric behavior of an extraneous gas as it is transported from reservoir to .surface conditions under changing temperatures and pressures has been programmed in a Kingston FORTRAN II language for digital computer analysis. The gases under investigation typify Gulf Coast reservoir gases within a 0.6 to 0.7 .specific gravity range. The program output has been substantiated by actual field cases. of gas kicks encountered in Gulf Coart we1l.s. The development of empirical equations for calculating suitable gamy deviation factors for unique temperatures and pressures was incorporated in the program to provide realistic solution.. An output listing of annular backpressures and corresponding equivalent fluid densities resulting at a predetermined critical depth (casing setting depth) and total depth for selected .stages of circulation is provided in a chronological .sequence. Additional information including reservoir pressure and temperature, kill rnrid density, produced gas or surface volume of the expanded gas intro vion, drill pipe and annular volumes can he obtained from the model. This paper illustrates that a precise knowledge of the volumetric behavior of extraneous gases in annular flow and its effect on equivalent fluid densities at a critical depth is significant and should receive .serious consideration in controlling threatened blowouts and in the design of drilling programs. Surface pressures in excess of formation limitations are a threat to zones of lost circula/ion and are potentially injurious to productive intervals. A knowledge of annular backpressure and equivalent fluid density profiles for probable gas kicks aids in a technological accomplishment of drilling programs and provides a .sale tolerance in the event a threatened blowout is encountered. Introduction Drilling operations are frequently interrupted when the drill bit penetrates permeable gas sands with reservoir CtfuJ manuscript was received in Society of Petroleum Engineers ofice Am. 1 1967. Revised manuscript received JuIy 7. 1968. Paper (SPE 1860) kae presented at SPE 42nd Annual Fall Meeting held in Houston. Tex., Oct 1-4, 1967. @ Copyright 1968 American Institute of Mining, Metallurgical, and Petroleum Engineem, Inc. pressures greater than that exerted by the drilling fluid. The differential pressures resulting permit an extraneous influx of gas into the wellbore. A suspension in drilling progress is necessary to restore fluid equilibrium throughout the system. Whether formation gas kicks originate unintentionally or by design, the prospect of a threatened or actual blowout exists and a method assuring a safe and effective well control procedure must be observed. A significant contribution to well control technology was advanced by Records et a1.l in 1962. Using the concept of transmitting a constant equivalent formation pressure at the point of intrusion, Records et al. introduced a calculation technique providing the annular backpressures encountered in a well control environment as a func tion of the volumetric behavior of a 0.6 specific gravity natural gas. In essence, the procedure outlined an annular backpressure schedule in terms of fluid volume circulated at different stages of a well control operation. A number of other publications2-' proposing various techniques for controlling gas intrusions in a wellbore achieve pressure control essentially through maintenance of a constant bottom-hole pressure by surface choke adjustments. The subsequent pressure effects induced in the annulus unfortunately receive little emphasis. Due to the tedious and repetitive nature of annular backpressure computations, a theoretical solution by digital computer is introduced for predicting annular backpressure and equivalent fluid density profiles associated with controlled gas kicks. We point out the effects of volumetric behavior of extraneous gases in annular flow and related field phenomena on equivalent fluid densities at a critical depth. The investigation indicated that equivalent fluid densities at a critical depth are of significance and should receive consideration in the control of threatened blowouts and in the design of drilling programs. Theoretical Considerations The mechanism of vertical gas flow through an annulus is governed by the PVT properties of the fluid, the pressure distribution within the system, the fluid flow rates and the geometry of flow. Due to the numerous variables involved in this type of problem, certain assumptions were imposed in deriving the mathematical model and in establishing the solutions. Two gases, characterized by specific gravities of 0.6 and 0.7, were selected to typify Gulf Coast reservoir fluids. The gas intrustion entered the wellbore as an immiscible 'References given at end of paper. JOURNAL OF PETROLEUM TECHNOLOGY

Jan 1, 1969

By C. L. Bulow

In this discussion of stress-corrosion cracking of widely used copper-base alloys, no attempt has been made to prepare an extensive review or bibliography since this has been quite ably covered by other investigators. An excellent bibliography was published by H. P. croft(1)2 in connection with his studies of stress-corrosion cracking in mercurous nitrate solutions and his analyses of the magnitude and distribution of stresses in brass parts. We are reporting on a few of the results which have been obtained to date in connection with an ammonia vapor test and an alternate immersion test. These are accelerated corrosion tests for determining the susceptibility of materials to failure from season or stress-corrosion cracking due to the presence of moist ammonia and oxygen so prevalent in nature. Our experiences with the ammonia test seem to indicate that it is a more searching test, than the mercurous nitrate test.

Jan 1, 1945

By Max Roesler

Page I. Introduction........................... 78 Location.......................... 78 Scope of Work and Acknowledgments.............. 79 History and Mining...................... 80 I1. Topography and its Interpretation................. 80 III. Petrology............................ 82 Sedimentary Rocks...................... 82 Description....................... 82 Age.......................... 84 Igneous Rocks........................ 85 Diabasic Rocks..................... 86 Dioritic Rocks...................... 87 Granitic Rocks...................... 88 Later Dike Rocks.................... 88 IV. Areal Geology.......................... 88 Rock Types Found in the District............... 88 Distribution of the Various Rock Types............. 89 Surface Distribution................... 89 Vertical Distribution................... 90 Causes of Present Areal and Vertical Distribution of the Various Rock Types..................... 91 Faulting...................... 91 Magmatic Differenti~tion............... 91 Tilting........................ 95 Erosion....................... 96 V. General Description of Ore Deposits................ 96 Nature of Ore ........................ 96 Shap~ and Size of Orebodies.................. 96 Geologic Position....................... 97 Mineralogy......................... 98 Distribution....................... 98 Interpretation...................... 99 Superficial Alteration................... 102 VI. Genesis of the Ore Deposits.................... 104 Previous Theories...................... 104 J. P. Kimball...................... 104

Jan 1, 1917

By W. R. Shimer, F. O. Kichline

The investigation herein described was carried out for the purpose of studying, both by chemical and metallographical means, the extent of over-oxidation of steel that can be accomplished by excessive overblowing in a Bessemer converter. 111 addition there are appended some results of basic open-hearth and crucible steels. Remarks on Chemical Methods. The test block used was hemispherical in shape, 4.5 in. in diameter and 2 in. thick. Drillings for analysis were obtained by drilling through the entire solid part of the block, carefully avoiding all cracks and blow-holes and mixing these drillings thoroughly. Drillinga were carefully examined for scale and the finest were gone over with a microscope to be sure all scale from whatever source had been removed. Oxygen was determined by the well-known method of Ledebur, modified according to Cushman,1 with, however, the removal of the preheating tube, which was found unnecessary. This method has been found to give concordant results. Blanks run from 0.0003 to 0.0006 g. Duplicate determinations varied not more than 0.001 to 0.003 per cent. It seems to be generally supposed that the hydrogen method gives only that oxygen which is combined with iron. Whether this be true or not, the content of oxygen existing as iron oxide no doubt predominates sufficiently, so that the result obtained is sufficient to indicate whether the steel is over-oxidized or not. We are well aware that the oxides of manganese and chromium, when existing alone, are not reduced by hydrogen at a red heat. To learn of their action in steel the following work was carried out: A sample of ferro-manganese and of ferro-chrome were each exposed

Jan 1, 1914

By J. E. Hilliard

Various methods are given for estimating the number per unit volume and average size of convex particles from measurements on a projection through a slice of the structure. The determination of the size distribution is considered specifically for spherical particles. The results are applicable to any type of transmission microscopy and also to the correction of measurements made by reflected light on semitransparent materials. WITH the advent of electron transmission microscopy, the metallurgist is confronted with the problem of relating a projected image to the three-dimensional properties of the structure. This paper deals with the estimation of the number per unit volume and size of particles dispersed in a matrix. The case of convex particles will first be treated (the results will be applicable as approximations to particles of more general shape) and then spherical particles will be considered specifically. The latter represent a special case frequently encountered in practice and one which is also amenable to a calculation of the effect of overlap on the observed particle-size distribution. Although the present treatment was prompted by the needs of the electron microscopist, the results are applicable to transmission studies with any type of radiation. In addition, they can be used in the analysis of semitransparent materials by reflected light, the depth of light penetration corresponding to the thickness of the slice or section used in the transmission studies. 1) CONVEX PARTICLES 1.1) General Expression for N,. We will suppose that a "center" (such as the center of mass) is assigned to each particle. The convention used for defining the center is immaterial providing it does not depend on the orientation or location of the particle. Consider a slice through the structure having a pair of parallel faces a distance t apart. It will be assumed that the slice is randomly located with respect to its perpendicular distance from some fixed point, but it is not necessary to assume that its orientation is random. Our problem is to deduce the relationship between the number of par- ticle images seen on an orthogonal projection through the slice with the number, Nv, of particles per unit volume in the original structure.* *Symbols are listed in the Table. The expected number of particles with centers lying within the slice is Nvt per unit area. In addition, there will be elements in the slice contributed by particles whose centers lie without. The number of such elements will be the same as the number of intersections occurring on a two-dimensional plane through the structure; namely N~K, where K is the mean distance, Fig. 1, between tangent planes to a particle averaged over all particles, i.e., Where Ni is the number of particles of class i having the same shape and size, and pi (4, 8) is the probability that an i particle will have a given orientation with respect to the slice. If the particles are randomly oriented, then K is independent of the orientation of the slice and equal to the mean cali-per diameter. The total number of particle elements in the slice is therefore Nv(t + K) per unit area, but fewer will be seen as separate images on the projection plane because of overlap. If MA is the number of elements "lost" by overlap, the number of images per unit area will be NA = Nv(t + K) -MA 121 MA is a function of the slice thickness and must vanish at t = 0. As t increases, NA at first increases, reaches a maximum, and thereafter decreases as the overlap term MA becomes predomi-

Jan 1, 1962

By Lloyd B. Underwood

Dr. Gardener, in Chapter 2, has presented a comprehensive state-of-the- art review of site investigations For tunneling. Nearly all of the techniques he discussed will also be required for future site investigations. Therefore, this chapter will be devoted to a few rather new exploration techniques plus ideas for improving some of the present-day methods. In March 1962, the first symposium on "Remote Sensing of Environment" was held at the University of Michigan.l Since that time, four additional symposiums have been held at the same University. Also, the technical Literature has recently included a number of articles on remote sensing techniques. A recent one appeared in the February 1968 issue of Materials Research and Standards.Vt was entitled "Developments in Remote Sensing Applicable to Airborne Engineering Surveys of Soils and Rocks," and was written by Dana C. Parker. Mr. Parker predicts that aerial reconnaissance will someday supplant soil augers, rock drills, surface reconnaissance, and geophysical surveys as the engineer's primary means of obtaining information about soils and rocks. He states, "The engineer wishing to survey a route or a site or to locate rock and soils suitable for construction projects will be able to push some buttons in an airplane and record all the data required for determining the relevant conditions. In a short time after he returns to earth with his rolls of film and charts, he will be able to reduce and analyze the data by partially computerized techniques and to compile a concise and comprehensive engineering report that gives all the relevant information about rocks, soil, water, and vegetation in the area he surveyed. Most important he will feel as confident with his recommendations, derived primarily from image characteristics and spectral power distributions, as his predecessors did with recommendations based on more tangible evidence obtained from drill cores and surface reconnaissance." The airborne sensors for engineering surveys of soils and rocks are those that sample some electromagnetic property of the materials that com- prise the terrain and cover its surface. In addition to cameras, these include

Jan 1, 1970

By Roshan B. Bhappu, Zeki M. Dogan

Two magnesite ores containing 3.15% and 8.73% SiO2 and a calcined magnesite product assaying 2.6% Si02 were first reduced in size to -20 mesh by roll crushing. 'They were then treated dry on a high intensity magnetic separator to reduce their silica content by rejecting iron-stained silicate minerals in the magnetic fraction and obtaining marketable magnesite or calcined magnesite as a nonmagnetic product.

Jan 1, 1975

By Samuel S. Wyer

Discussion of the paper of SAMUEL S. WYER, presented at the New York meeting February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 263 to 279. DAVID T. DAY, Washington, D. C.-I would like to ask whether the court decisions quoted in the paper are general, or do they represent one side of the case; if so, are there any decisions that represent more than one side of the case? Are they of general application, or do they affect only one side? Also, what is the difference between a pump and a compressor from the standpoint of the natural-gas industry? I notice stress is laid on the word "pump" in. connection with some of the legal decisions, and then it is stated. that they must not pump or compress above 300 lb. The question is, is a pump a compressor and a compressor a pump, under certain conditions? SAMUEL S. WYER, Columbus, Ohio.-Answering the first question, I will say that the decisions cover both sides of the case very thoroughly, and are uniformly on the side that a company is justified in the use of gas compressors; in other words, there are no decisions holding it to be illegal to use gas compressors, with the exception noted in Indiana, Kansas, and Oklahoma where you cannot go below atmospheric pressure. In regard to the second question, I think the engineers and the gas operators themselves are responsible for the confusion. It is because the use of the term "pump" is almost universal, and so many people have obtained the idea that the primary function of a gas compressor is to pump air into the gas, in order to increase the consumers' gas bills. I appreciate that it is very hard to draw a clear line of demarcation. between a pump and a compressor. The distinction I have always made myself, and which I think is a logical one, is that you do not get the pumping action until you get below atmospheric pressure. As far as the compression end is concerned, there is only one State, namely, Indiana, that has any statutory limitation with regard to how high the pressure may be increased in order to put the gas into the transmission lines. The State law in Indiana limits the maximum pressure to 300 lb. per square inch.

Jan 5, 1916

By C.A. Zapffe

Both the foundryman and the theoretical metallurgist are now generally agreed that the anomalous "rising" or "bleeding" of certain ferrous castings of killed metal is primarily attributable to hydrogen. How and why the phenomenon occurs, however, have not been made clear. The following discussion is intended to harmonize foundry experience with metallurgical theory so that the foundryman may possibly improve his ability to prognosticate whether a certain casting may bleed or not. Bleeding, Rising, and Piping The "rising" to be discussed here is not to be confused with the action in rimming ingots as a result of the carbon-oxygen reaction, although a conclusion will be drawn that may apply to the art of controlling the rimming action. Only killed metal is considered, which includes both steels and irons. In Fig. I, three killed, chill-cast ingots are shown: a porous ingot whose evolution of gas during late stages of solidification has ejected metal through the top; an ingot in which moderate gas evolution during solidification has lifted the mushy central metal, i.e., it has "risen"; and, third, a sound ingot with good piping characteristics. The first type is referred to as "bleeding," and generally infers that a solid skin had first formed through which the liquid metal later erupted. There is no fundamental distinc- tion between bleeding and rising in reference to killed metal.* Porosity Hydrogen appears as a cause of bleeding because the gas evolution simultaneously leaves a porosity of a type traceable to hydrogen. Twenty years ago, Melmoth' noted that killed steel that rose unexpectedly in the mold, if returned while liquid to the furnace and heated further under a reducing lime slag, would again rise in the mold; but that if the ingot were allowed to solidify and was then remelted no rising occurred. A critical quantity of the responsible gas is therefore removed by the rising action. Melmoth associated rising with high silicon (0.7 to 0.9 per cent) and concluded that silicon increased gas absorption. Because silicon is a strong deoxidizer, oxygen must, therefore, be eliminated from consideration of the three common gases in steel—oxygen, nitrogen, and hydrogen. Butterworth2 later decided that pinhole porosity was caused by gases dissolved in the metal and that hydrogen was obtained from steam in the mold. Allen's classical work on copper castings,3 soon followed by

Jan 1, 1943

By C. A. Zapffe

Both the foundryman and the theoretical metallurgist are now generally agreed that the anomalous "rising" or "bleeding" of certain ferrous castings of killed metal is primarily attributable to hydrogen. How and why the phenomenon occurs, however, have not been made clear. The following discussion is intended to harmonize foundry experience with metallurgical theory so that the foundryman may possibly improve his ability to prognosticate whether a certain casting may bleed or not. Bleeding, Rising, and Piping The "rising" to be discussed here is not to be confused with the action in rimming ingots as a result of the carbon-oxygen reaction, although a conclusion will be drawn that may apply to the art of controlling the rimming action. Only killed metal is considered, which includes both steels and irons. In Fig. I, three killed, chill-cast ingots are shown: a porous ingot whose evolution of gas during late stages of solidification has ejected metal through the top; an ingot in which moderate gas evolution during solidification has lifted the mushy central metal, i.e., it has "risen"; and, third, a sound ingot with good piping characteristics. The first type is referred to as "bleeding," and generally infers that a solid skin had first formed through which the liquid metal later erupted. There is no fundamental distinc- tion between bleeding and rising in reference to killed metal.* Porosity Hydrogen appears as a cause of bleeding because the gas evolution simultaneously leaves a porosity of a type traceable to hydrogen. Twenty years ago, Melmoth' noted that killed steel that rose unexpectedly in the mold, if returned while liquid to the furnace and heated further under a reducing lime slag, would again rise in the mold; but that if the ingot were allowed to solidify and was then remelted no rising occurred. A critical quantity of the responsible gas is therefore removed by the rising action. Melmoth associated rising with high silicon (0.7 to 0.9 per cent) and concluded that silicon increased gas absorption. Because silicon is a strong deoxidizer, oxygen must, therefore, be eliminated from consideration of the three common gases in steel—oxygen, nitrogen, and hydrogen. Butterworth2 later decided that pinhole porosity was caused by gases dissolved in the metal and that hydrogen was obtained from steam in the mold. Allen's classical work on copper castings,3 soon followed by

Jan 1, 1943