Search Documents

By G. W. Bain

The Canadian magnesite deposits are situated in Grenville township, about 8 miles from Calumet station, on the Canadian Pacific Railway, but the poor transportation facilities have hindered their development. Magnesite was discovered in the boulders near White Rock Lake by Rev. W. P. Boshart in 1900. Observing that the material of these boulders was more glistening and whiter in color than Grenville limestone, he sent a specimen to the Department of Mines, Ottawa. An analysis showed this to be almost pure carbonate of magnesia and of commercial value if present in sufficient quantities. That summer, Boshart and McAllister found numerous outcrops, both of boulders and of bed rock, that gave promise of being magnesite of a commercial grade, and decided that this mineral deposit, if developed, would rival that at Veitsch, Austria. So they procured options on most of the land on which they knew the magnesite occurred. But the transportation difficulties were too great for the deposits to be mined at the prices offered for the product. In 1907, T. J. Waters organized the Canadian Magnesite Co. and opened a quarry on the north half of lot 18, range IX, and later on lot 15, range IX, of the same township. A lirnestone kiln was erected and the calcined rock was hauled to Calumet. In 1914, the North American Magensite Co, took over the quarries and shipped both crude and calcined magnesite until January, 1923. During 1915, S. Melkman organized the Scottish Canadian Magnesite Co. and opened a quarry on lot 15, ranges X and XI, Grenville township. A light, narrow-gage railway connects this quarry with the C. P. R. at Magnesite station. but shipments are made only during the summer months. Numerous other quarries have contributed to the output of the district but the greater part has come from the open pits of the

Jan 1, 1923

By Dr. O’Neil Thomas J., Donald W. Gentry

"October. This is one of the peculiarly dangerous months to speculate in stocks. The others are July, January, September, April, November, May, March, June, December, August and February." -Mark Twain Although the preceding chapters describe the type of preliminary evaluation frequently performed in the mining industry, it has been assumed that input data are known with certainty-clearly an enormous simplification. In reality, estimates of ore grade, mining cost, metal price, etc., are subject to varying degrees of uncertainty due to the inability to predict the future with much precision. Management would probably not, for example, be equally attracted to two projects each offering a 20% DCFROI-one for a new gold venture in Nevada and the other for an undersea manganese nodule operation in the Pacific. The high risk with the latter investment tells the obvious; there is more to investment decision-making than a deterministic analysis using "best estimates" of input parameters. The science of decision theory normally distinguishes between decisions under uncertainty, where probabilities of various outcomes are unknown; and decisions under risk, where such probabilities can be estimated. The first case is rarely en- countered in practical capital investment analysis in mining, so the remainder of this chapter focuses on that class of problems where rational probability distributions for the future states of input variables can be estimated. RISK IN MINING Risk in the context of this chapter is the unforeseen deviation of individual cash flows from expected values for a capital project. For a mining venture, the source of this uncertainty could be any number of factors relating to such items as ore grade, ore reserve tonnage, operating costs, product prices, etc. With conventional *Adapted from O'Neil, T.J., 1979, "Procedures for the Preliminary Financial Evaluation of Metal Mining Ventures," Computer Methods for the 80s, A. Weiss, ed., AIME, New York, pp. 556-573.

Jan 1, 1984

By D. P. Harris

This paper surveys a few of the quantitative exploration models that might be of interest to an ex-plorationist seeking to apply methods of operations research to mineral exploration. A general development of each model is presented, and the model is evaluated relative to the exploration activity. Finally, a philosophy of exploration and mineral resources is presented, and a possible exploration strategy incorporating concepts of some of these models consistent with this philosophy is proposed. The high cost of conducting an effective exploration program has generated an increasing interest in methods of optimizing the allocation of the resources of a firm engaged in mineral exploration. As a step towards this, mathematical models have been formulated which are designed to quantify those variables of mineral exploration in such a manner that they can be integrated with all phases of the firm's operations so as to optimize its profit objective. QUANTITATIVE MODELS General: Exploration models express at least two concepts: mineral occurrence and effectiveness of search. In simplest terms, an exploration model might be formulated mathematically as follows: P(X) = F(X) . G(X), where P(X) = the unconditional probability of discovery of X deposits, F(X) = the probability of occurrence of X deposits, and G(X) = the probability of discovery of X deposits, conditional upon their existence in the search area. With these general models as a basis of reference, some of the specific exploration models are examined below. The Allais Model: DEVELOPMENT - M. Allaisl performed the first study in which a philosophy of exploration was formulated into a probability framework. His objective was to estimate the economic profitability of the exploration of the Algerian Sahara. Allais divided the Algerian Sahara into blocks of land (called cells) 10 km square and defined the random variable, X, as the number of mining districts per cell. Thus, F(X) would describe the probability of 1, 2, or n mining districts occurring within any cell of the search area. Allais reasoned that his best information as to the form of the distribution, F(X), was the number of mining districts per cell that had been found in well explored areas in the world, such as the Western States of the U.S. He found that the Poisson function produced a reasonably good fit to the distribution of districts in these explored areas: where? is a parameter, such as the average number of districts per cell. Thus, by determining the value

Jan 1, 1968

By Hoyt Gale

RECENT work on borate deposits near Kramer, in the extreme southeast corner of Kern County, California, is of special interest to those who are making a study of the mode of origin of the borate minerals colemanite and ulexite. A valuable clue to the mode of origin of colemanite in its present known deposits is given in a paper by W. F. Foshag1, of the United States National Museum. Colemanite is found in or near original deposits of ulexite, from which it is supposed to have been derived by a change in the rate of movement or the character of the ground water. Indications that an alteration of this sort had produced colemanite were first recognized by the writer' in specimens collected in the Kramer district in 1920, and sent to W. T. Schaller, at U. S. Geological Survey, for identification. The identity of the two borate minerals in these specimens was not at once determined, but the relations of the minerals as seen in the specimens afforded a manifest clue to the origin of the deposits. Similar specimens were obtained by the writer from deposits in death Valley soon after he had examined the deposits near Kramer. After studying the specimens submitted to him Dr. Schaller wrote as follows: "I have finally positively identified the boron minerals you sent me with your letter of Sept. 27. The `white fibrous mineral like ulexite' is ulexite; the harder nodules' in the clay are colemanite, apparently formed from the ulexite as a result of leaching, with recrystallization in place-a theory that Foshag is working on." The present paper is a report on the facts observed at. the deposits near Kramer, and some general observations on the geological relations noted, which, unfortunately, still form only a very incomplete record.

Jan 2, 1926

By Cyril Stanley Smith

The method of thermal analysis, so important in the development of metallographie science, has of recent years been falling into disuse owing to the development of other physical methods which give result's easier of interpretation and which can be used for the study of either equilibrium or transitional conditions because they do not require a continuously changing temperature. Nevertheless thermal analysis remains useful in the study of reactions that take place rapidly, and the simplicity of the experimental technique and the general availability of the apparatus involved are point's in its favor. Theoretically, thermal analysis is capable of giving specific and latent hat measurements and therefore should permit the study of reactions on a more fundamental basis than any other method. It is, however,difficult or impossible to obtain quantitative heat measurements from cooling curves obtained in the usual way. Even if the furnace containing the sample is cooled or heated at a linear rate, or if a gradient furnaec is employed to maintain a constant rate over a large range of temperature, the heat flow from or to the specimen depends on its previous history, for the difference of temperature between the specimen and its surroundings varies. The emissivity of the specimen surface, moreover, is unlikely to be constant. The able mathematical analysis by Russrll,1 although it prevent,s misinterpretat,ion of data, has an effect rather the reverse of that intended, and leaves the reader doubtful of the possibility of ever obtaining quantitative results from thermal curves. Nothing can be done to apply thermal analysis t'o the study of equilibrium conditions of reactions that arc not completed at rates of temperature change above about 1° C;. per minute, and this unfortunatetly excludes most solid transformations in alloys.† For the determination of liquidus

Jan 1, 1940

By Cyril Stanley Smith

The method of thermal analysis, so important in the development of metallographie science, has of recent years been falling into disuse owing to the development of other physical methods which give result's easier of interpretation and which can be used for the study of either equilibrium or transitional conditions because they do not require a continuously changing temperature. Nevertheless thermal analysis remains useful in the study of reactions that take place rapidly, and the simplicity of the experimental technique and the general availability of the apparatus involved are point's in its favor. Theoretically, thermal analysis is capable of giving specific and latent hat measurements and therefore should permit the study of reactions on a more fundamental basis than any other method. It is, however,difficult or impossible to obtain quantitative heat measurements from cooling curves obtained in the usual way. Even if the furnace containing the sample is cooled or heated at a linear rate, or if a gradient furnaec is employed to maintain a constant rate over a large range of temperature, the heat flow from or to the specimen depends on its previous history, for the difference of temperature between the specimen and its surroundings varies. The emissivity of the specimen surface, moreover, is unlikely to be constant. The able mathematical analysis by Russrll,1 although it prevent,s misinterpretat,ion of data, has an effect rather the reverse of that intended, and leaves the reader doubtful of the possibility of ever obtaining quantitative results from thermal curves. Nothing can be done to apply thermal analysis t'o the study of equilibrium conditions of reactions that arc not completed at rates of temperature change above about 1° C;. per minute, and this unfortunatetly excludes most solid transformations in alloys.† For the determination of liquidus

Jan 1, 1940

By D. C. McLean, S. A. McKay

The purpose of this paper is threefold: 1) to describe actual ground control installations made at the various mines of the International Nickel Co. (Canada) Ltd mines in Sudbury, Ont. during a planned test program. 2) to suggest new ground control techniques which are now possible by the use of fully grouted bolts 3) to indicate the possible economic advantages to be gained by the use of resins and resin grouted bolts to control difficult ground conditions. Were a theme selected for this paper it would be: "Preserve the original roof in best condition possible by the use of smooth blasting techniques and fully grouted roof bolts — since the original rock is the best and cheapest material available for ground support." TYPES OF BONDED BOLTS As has been shown previously, there are several ways in which a bolt may be bonded. These are illustrated in Fig. 1 and 2. There are three general types of grouted bolts: 1) pretensioned, 2) post-tensioned, and 3) untensioned. The type which will be of most benefit to the user will depend upon the particular ground support problem involved. Despite the many arguments propounded for the necessity for using a tensioned bolt, ample evidence exists from actual experience that untensioned bolts can be effective in many instances. The outstanding characteristic of a grouted bolt is that it provides the user with a variety of rock consolidation techniques heretofore unavailable with conventional rock bolts. Many of the unusual characteristics of grouted reinforcing bar have been evaluated by researchers in the concrete structure field.' Underground application has largely been pioneered in the construction field, with especially good work being reported from the Snowy Mountains Hydroelectric Authority in Australia. Techniques developed there using cement grouted bolts are now being adapted in many large government construction projects in this country with excellent results. The ap- plications described in this paper are those in which Cyanamid's Roc Loc Mining Kits were used exclusively. SLUSHER DRIFTS AND FINGER RAISES (BOX HOLE BROWS, DASHES) A common mining problem especially where block caving methods are applied is that of maintaining the roof in slusher trenches particularly at the intersections of the trench with the feed raises (box holes) through which the large fragments of broken ore tumble. Typical sections are shown in Fig. 3 and 4. In Fig. 3, the drift is normally driven 7 ft wide by 8 ft high initially. The rock involved is a hard norite (diabase) which is usually competent but has "block cleavage". This roof has a tendency to fall out in large blocks when subjected to operating stresses. Depending upon the initial condition of the roof, the drift is either lined with 2 to 3 ft of concrete immedi-

Jan 1, 1964

ALBERT SAUVEUR, Chairman. A. A. STEVENSON, Vice-Chairman. HERBERT M. BOYLSTON, Secretary, Abbot Bldg., Cambridge, Mass. John Birkinbine, William Kelly, J. S. Unger, William H. Blauvelt, Charles Kirchhoff, Felix A. Vogel, James Gayley, Richard Moldenke, Leonard Waldo, Henry D. Hibbard, Joseph W. Richards, William R. Walker, Henry M. Howe, C. F. W. Rys, William R. Webster, Robert W. Hunt, E. Gybbon Spilsbury, Frederick W. Wood. J. E. Johnson, Jr., The innovation of a special meeting under the auspices of the Iron and Steel Committee was well justified, if we accept as a criterion the number of papers presented at the meeting held on Oct. 16 and 17 in New York and the attendance at that meeting. Twenty-four papers were read, and most of these were widely discussed orally, while doubtless the written discussions will be even larger in extent. Discussions will be received up to Dec. 1, 1913. The attendance at the meeting of 106 members and 75 guests is an evidence of the wide anti growing interest in the Institute of men interested chiefly in iron and steel. It is especially interesting to note this large attendance at a meeting where very little of a social nature was introduced into the program. An informal dinner for the men at the Engineers' Club closed the meeting. At this dinner were present about 70 members and guests. One of the Vice-Chairmen and the Secretary of the new Committee on Petroleum and Gas told of the important plans in prospect of that Committee. Brief impromptu speeches by a considerable number of the members and guests were enjoyed. Professor Marburg reiterated his previous assertion that he believed that the Institute and the American Society for Testing Materials, as well as some of the other technical societies, were all fighting for one good cause; that there was room in the field for all of these societies with their various points of view; and that they should march shoulder to shoulder. The success of this dinner was due largely to the efforts of Mr. Johnson who had the affair in charge.

Jan 11, 1913

By L. W. Bahney

Many methods for the determination of gold or silver, or both, in cyanide solutions have been published, which with care in manipulation, and modification in some cases, will give results that are satisfactory. It is possible to classify or group these methods as follows: 1. Evaporating the solution in a porcelain or agate-ware dish containing litharge,l or in a "boat" made of lead foil. 2. Forming a lead sponge containing the precious metals by means of zinc shavings,2 zinc dust,3 or a piece of aluminum.4 3. Decomposing the cyanide solution with an acid and precipitating the precious metals by the use of one or a combination of some of the following: Copper sulphate,5 sodium sulphite,6 hydrogen sulphide,' cement copper.ll 4. Precipitating the silver by zinc dust held in a Gooch crucible and determination with a standard solution of sulphocyanate.9 5. Electrolysis.l0 . 6. Colorimetry.ll

Jan 1, 1915

By Paul R. La Pointe

GEOTECHNICAL OBJECTIVES OF UCG PROGRAM Underground coal gasification (UCG) is one of several in situ extraction technologies for utilizing deep, otherwise unmineable coal. This technology involves the injection of air or oxygen into the target coal seam, ignition of the coal and recovery of product gases. Geotechnical characteristics of the coal and enclosing rock strata strongly influence the success of this Process. The flame front follows the coal cleats (Hill, 1979), and cleating and bedding control the manner in which coal collapses into the cavity, thereby affecting recovery efficiency (Ramirez and others, 1982). Moreover, coal seams typically behave as fracture dominated aquifers in which cleat orientations govern subsequent contaminant dispersal. For these reasons, the Anaconda Minerals Co. undertook a detailed study of fracturing within the Wyodak-Anderson Coal in the eastern Powder River Basin (PRB) near its Rocky Hill UCG test site (Fig. 1). STRESS HISTORY AND FRACTURING IN THE POWDER RIVER BASIN Vertical jointing, or cleating, in coals may arise from shrinkage shortly after deposition under low confining pressures, or later in time, soon after burial but after the coalification process is well advanced (Ting, 1977). There is much evidence to support the formation of cleating after coalification (e.g. Hawkes and Mellor, 1970; McCulloch and others, 1974), which suggests that the stress state existing at that time strongly influences cleat formation. McCulloch and others (1974) argue that the typically better developed face cleat forms parallel to the plane containing [ol] and [o2]. Where the relation between cleats and stess has been studied (McCulloch and others, 1974; Stone and Snoeberger, 1977; Ward, 1977; Kulander and Dean, 1978), the highly systematic face cleat strongly parallels the [o1] direction. Stone and Snoeberger (1977) report face and butt cleat measurements of N70E and N29W for the Felix Coals 220 m stratigraphically above the Wyodak at the Hoe Creek UCG site (Fig. 1). Structural trends also indicate the past state of stress in the PRB. Glaze and Keller (1963) suggest that the NE-SW regional compression during the late Permian formed major N-S fold lines and basement magnetic anomalies. Mapel (1959) describes folds having N60W and N30W rends in the northern PRB, as well as a large normal fault trending northeast. Glass (1976) also describes normal faults trending northeast. Similarly, Olive (1957) mapped normal faults

Jan 1, 1984

By Herman Dykstra, R. L. Parsons

A numerical method for solving partial differential equations in steady state fluid flow is described. This method, known as the "relaxation method," has two advantages over analytical methods: (1) practically any problem can be solved, and (2) a solution can be obtained quickly. A disadvautage is that the solution is not general. The method is applied to core analysis and relative permeability measurement to calculate constriction effects and to calculate the true pressure drop measured by a center tap in a Hassler type relative permeability apparatus. Further applications are suggested. INTRODUCTION Many problems in fluid flow cannot be solved analytically because of the nature of the boundary conditions. For many problems, however. an exact answer is not necessary because boundary conditions are not exactly defined or the parameters describing the porous medium are not accurately known. The relaxation method can be used to obtain an approximate answer easily and quickly for the flow of incompressible fluids in porous media. The method can also be used for other types of problems, such as determining the stress in a shaft under load. or the temperature distribution during steady state heat flow. In this discussion only calculations concerned with the flow of fluids in porous media will be considered. The method was introduced by R. V. Southwell in 1935.' THEORY The treatment given here follows that given by Enimons.2 Consider a porous medium to be replaced entirely by a net of tubes of equal length and uniform cross-sectional area as shown in part in Fig. 1. Assume that the net of tubes behaves exactly like the porous medium which it replaces; that is, the net can be made fine enough to reproduce exactly the porous medium. Assume also that Darcy's Law can be used to calculate the flow from one point to another point through these tubes. The flow from point 1 to point 0 is KA . ------ P-P) .......(11 where a is the distance between points: K is the "permeability" of a tube; A is the cross-sectional area of a tube; is the viscosity of the liquid in the porous medium; and (P1 — P0) is the pressure difference between point 1 and point 0. In like manner the flow can be calculated from points 2, 3, and 4 to point 0. The net flow into point 0 is Qo = KA/µa (P1 + P2 + P33 + P4-4P0) . . (2) MB For an incompressible fluid the net flow into point 0 will be zero or, Q. = 0. This says that at point 0 fluid is neither being accumulated nor depleted. 'Therefore. P1 + P2 + P3 + P4 - 4P0 = 0 .... (3) . If. now. with specified boundary conditions. the pressure i.; known at a finite number of points in a given region, as at the points shown in Fig. 1, Equation (3) will be satisfied at every point. If, on the other hand, the pressure is not known, the pressure can be guessed at these points. Then. unless the guess is perfect. Equation (3) will not be satisfied at all of the points. When Equatiol~ (3,) is not satisfietl. let d = P1 + I?, + P, + P, - If' .,....(4) where 6 is an apparent error and is called the residual at point 0. Equation (4) shows how much the pressure guess is in error at point 0 with respect to the surrounding points. A positive residual means that the pressure is too low, and a negative residual means that the pressure is too high. To bring the residual, 6. to zero in order to satisfy Equation (3). it is necessary to make changes in the pressure guesses. Equation (4) shows that a +1 change in Po will change the residual at point 0 by -4. A +1 change in the pressure at any of the four surrounding points will change the residual at point 0 by +l. Thus it can be seen that a change at any point will affect the residual at that point and the four surrounding points. By changing the pressure from point to point, all of the residuals can eventually be brought nearly to zero and the problem will be solved. This procedure is the essence of relaxation methods and is used to relax the residuals so that Equation (3) is satisfied at every point. The procedure can be most easily explained in detail by solving a simple problem. as Southwell says, "To explain every detail of a practical technique is to risk an appearance of complexity and difficulty which may repel the reader. A

Jan 1, 1951

By R. L. Parsons, Herman Dykstra

A numerical method for solving partial differential equations in steady state fluid flow is described. This method, known as the "relaxation method," has two advantages over analytical methods: (1) practically any problem can be solved, and (2) a solution can be obtained quickly. A disadvautage is that the solution is not general. The method is applied to core analysis and relative permeability measurement to calculate constriction effects and to calculate the true pressure drop measured by a center tap in a Hassler type relative permeability apparatus. Further applications are suggested. INTRODUCTION Many problems in fluid flow cannot be solved analytically because of the nature of the boundary conditions. For many problems, however. an exact answer is not necessary because boundary conditions are not exactly defined or the parameters describing the porous medium are not accurately known. The relaxation method can be used to obtain an approximate answer easily and quickly for the flow of incompressible fluids in porous media. The method can also be used for other types of problems, such as determining the stress in a shaft under load. or the temperature distribution during steady state heat flow. In this discussion only calculations concerned with the flow of fluids in porous media will be considered. The method was introduced by R. V. Southwell in 1935.' THEORY The treatment given here follows that given by Enimons.2 Consider a porous medium to be replaced entirely by a net of tubes of equal length and uniform cross-sectional area as shown in part in Fig. 1. Assume that the net of tubes behaves exactly like the porous medium which it replaces; that is, the net can be made fine enough to reproduce exactly the porous medium. Assume also that Darcy's Law can be used to calculate the flow from one point to another point through these tubes. The flow from point 1 to point 0 is KA . ------ P-P) .......(11 where a is the distance between points: K is the "permeability" of a tube; A is the cross-sectional area of a tube; is the viscosity of the liquid in the porous medium; and (P1 — P0) is the pressure difference between point 1 and point 0. In like manner the flow can be calculated from points 2, 3, and 4 to point 0. The net flow into point 0 is Qo = KA/µa (P1 + P2 + P33 + P4-4P0) . . (2) MB For an incompressible fluid the net flow into point 0 will be zero or, Q. = 0. This says that at point 0 fluid is neither being accumulated nor depleted. 'Therefore. P1 + P2 + P3 + P4 - 4P0 = 0 .... (3) . If. now. with specified boundary conditions. the pressure i.; known at a finite number of points in a given region, as at the points shown in Fig. 1, Equation (3) will be satisfied at every point. If, on the other hand, the pressure is not known, the pressure can be guessed at these points. Then. unless the guess is perfect. Equation (3) will not be satisfied at all of the points. When Equatiol~ (3,) is not satisfietl. let d = P1 + I?, + P, + P, - If' .,....(4) where 6 is an apparent error and is called the residual at point 0. Equation (4) shows how much the pressure guess is in error at point 0 with respect to the surrounding points. A positive residual means that the pressure is too low, and a negative residual means that the pressure is too high. To bring the residual, 6. to zero in order to satisfy Equation (3). it is necessary to make changes in the pressure guesses. Equation (4) shows that a +1 change in Po will change the residual at point 0 by -4. A +1 change in the pressure at any of the four surrounding points will change the residual at point 0 by +l. Thus it can be seen that a change at any point will affect the residual at that point and the four surrounding points. By changing the pressure from point to point, all of the residuals can eventually be brought nearly to zero and the problem will be solved. This procedure is the essence of relaxation methods and is used to relax the residuals so that Equation (3) is satisfied at every point. The procedure can be most easily explained in detail by solving a simple problem. as Southwell says, "To explain every detail of a practical technique is to risk an appearance of complexity and difficulty which may repel the reader. A

Jan 1, 1951

The Hurghada field is still the major producing field in Egypt. There was almost no activity in the Abu Durba field during 1936 and no new evidence is available. The following table summarizes the information on the Hurghada field for the year 1936. Hurghada Field Age of field to end of 1936, years.................... 23 Producing area for gas and oil, acres................. 1,050 Barbels Total oil production to end of 1936.................. 29,046,572 Total oil production during 1935.................... 1,212,182 Total oil production during 1936.................... 1,218,708 Daily average during November, 1936............... 3,249 MillionB CU. Ft. Total gas production (Aug. 1925 to end of 1936)...... 3,966 Total gas production during 1935................... 278 Total gas production during 1936................... 280 Maximum daily in 1936............................ 0.9 Number of producing wells completed to end of 1936... 94 Number of producing wells completed during 1936. ... 3 Number of wells abandoned during 1936............. 3 Producing wells at end of 1936...................... 768 Average depth of bottom of producing wells, ft....... 1,720 Average depth of top of producing horizon, ft......... 1,598 Character of oil, approx. average during 1936: Gravity at 60' F., 0.900; base mixed. Character of gas, approx. average during 1936: gallons gasoline per 1,000 CU. ft., 6.2. Producing rock (main): Nubian sands, Cretaceous; character, sand rock and sandy shales. 1 The figures given by the author were in tons. A conversion factor of 6.98. based on 0.900 sp. gr., was used to obtain the number of barrels.—Ed. 2 All pumping.

Jan 1, 1937

The following list of corrections has been compiled from the thirty-five volumes, with some additions: VOLUME I. Page 160. The first two sentences of the second paragraph should read as follows : " For No. II we find that 2.33 percent. A1,08 take 4.07 per cent. 8109, leaving 3.48 per cent. 8102 free, which requires 3.25 per cent. CaO." Page 160, line 14, 3.79 should be 3.25; and in the 15th and 18th lines, 48.44 should be 46.98. VOLUME VI. Page 59. The discharges of the miners' inch per second, given as .2624 and .2499 cubic feet, should be .02624 and .02499, respectively. The discharges per minute, hour, etc., are correctly given. VOLUME VIII. Page 214. 16th and 25th lines, ferric carbonate should be ferrous carbonate. Page 486, 16th line, 10,000 should be 5,000. [ ]

Jan 1, 1907

By A. J. Lena, M. F. Hawkes

Changes in hardness, tensile properties, microstructure, electrical resistance, and X-ray diffraction effects indicate that lattice strains are necessary for the embrittlement of ferritic stainless steels when heated for relatively short times at 475°C (885°F). It is suggested that 475°C (885°F) embrittlement is due to the accelerated formation of an intermediate stage in the formation of s under the influence of these strains. FERRITIC stainless steels (low carbon alloys of iron with more than 15 pct Cr) are subject to two forms of embrittlement when heated in the temperature range of 375° to 750°C. The embrittlement which occurs after long time heating between 565" and 750°C is well understood; it is caused by the precipitation of the hard, brittle s phase. Sigma is an intermetallic compound of approximate equi-atomic composition with an extended range of formation in Fe-Cr alloys. The maximum temperature at which this form of embrittlement can occur is dependent upon chromium content; and is approximately 620°C for a 17 pct Cr steel and 730°C for a 27 pct Cr steel. The other form of embrittlement occurs after relatively short heating periods in the range of 375" to 565°C; in the higher chromium steels, hours may be sufficient as compared to months for s embrittlement. This phenomenon is not at all well understood and several controversial theories have been proposed. The rate and intensity of embrittlement increase with increasing chromium content but the maximum rate occurs at 475°C re-gardless of chromium content. As a result of this, the phenomenon has been termed 475°C (885°F) embrittlement. The effect of 475°C embrittlement on the properties of ferritic stainless steels has been thoroughly reviewed by Heger.1 The embrittlement causes a pronounced decrease in room temperature impact strength and ductility, a large increase in hardness and tensile strength, and a decrease in electrical resistivity and corrosion resistance. Microstructural changes accompanying embrittlement are minor and difficult to interpret with a general grain darkening, appearance of a lamellar precipitate, grain boundary widening, and precipitation along ferrite veins having been reported at various times. With the exception of reported line broadening, X-ray diffraction studies by conventional Debye analysis of solid samples have been of little value. BY making use of electron diffraction methods, Fisher, Dulis, and Car-roll' have recently shown the existence of a chromi-um-rich, body-centered cubic phase in 27 pct Cr steels which had been aged at 482°C (900°F) for as long as four years. Two types of theories have been advanced to account for the embrittlement. The first of these requires the precipitation of a phase not inherent in the Fe-Cr system with various investigators suggesting a carbide,3 nitride,3 phosphide,4 or oxide." Theories of this type have difficulty accounting for the influence of alloying elements on the embrittlement and for the facts that a minimum chromium content is necessary for embrittlement and the intensity of embrittlement increases with increasing chromium content. The second type of theory that has been proposed relates 475°C embrittlement to s phase formation which is inherent in the Fe-Cr system. An assumption of this kind can adequately explain the influence of alloying elements, for they exert an effect on 475°C embrittlement similar to that on s phase for-mation as can be seen in Table I. The minimum chromium content is essentially the same for both phenomena and it has been shown12,13 that s is a stable phase in the embrittling temperature range. In addition, it has been reported14,15 that pure alloys embrittle to the same extent as commercial type alloys. There are, however, several factors which have prevented complete acceptance of a s phase theory. Foremost of these is that the embrittlement can be removed by reheating for short time periods above 600°C, which in the higher chromium steels is within the stable s region. No s has ever been observed after one of these curing treatments, nor has any s been found as a result of embrittlement at 475°C. In addition, the simple precipitation of s cannot explain the time-temperature relationships for reactions between 350°and 750°C. This behavior is shown schematically in Fig. 1. Newell 16 and Ried-rich and Loib4 have shown that 475°C embrittlement follows a C-type curve as illustrated, while Short-

Jan 1, 1955

By B. Ball, C. H. Cox, S. N. Yap

Electrokinetic measurements on cassiterite were made in the presence of sodium di-hydrogen phosphate, mono-hydrogen arsenate, bisulfite, and sulfate. Flotation studies were also conducted using sodium dodecyl sulfonate in the presence of these salts. It was found that the anions specifically adsorb on cassiterite in the order H2AsO-4 H2PO4 HSO3 SO4 and consequently cause flotation depression. The adsorption mechanisms of the various inorganic anions are discussed in detail.

Jan 1, 1980

By D. A. Stevenson, R. A. Burmeister

Single-phase silver antimony telluride has been prepared by zone-melting techniques using initial compositions of A new phase appears upon prolonged annealing of this material, but the reaction does not appear to be a simple eutectoid decomposition. A complete analysis of the phase equilibria is complicated by the slow kinetics involved. The Hall coefficient, magneto -resistance, electrical resistivity, and Seebeck coefficient are all sensitive to the presence of second phases. The low Hall mobilities measured for single-phase material indicate that the usual band theory is inadequate to explain the observed transport properties in the system. Density anomalies of up to 2.5 pet between measured and theoretical density were observed but are not conclusive evidence for a defect structure. COMPOSITIONS in the Ag-Sb-Te system have been studied previously by several investigators.1"18 The interest in this system arises from potential thermoelectric applications of alloys on the Ag2Te-Sb2Tes vertical section. Although the composition corresponding to the formula AgSbTe, has received most attention, it has been found to consist of more than one phase.7'8 A thorough understanding of the properties of this heterogeneous material has been impeded by both lack of knowledge of the properties of the homogeneous phases comprising it and the problem of analysis of transport properties in an inhomogeneous system. The present work describes the preparation of the homogeneous ternary phase and the corresponding electrical properties of both homogeneous and heterogeneous material. MATERIAL PREPARATION Most specimens for this investigation were prepared by encapsulating the elements in evacuated quartz tubes after which they were melted and homogenized in the liquid state. The ambient temperature was then dropped to 500°C and the resulting ingot zone melted. The growth rate, width of zone, stoichiometry, and number of passes have an effect on the resultant microstructure. Grains several centimeters in length were easily produced by this method. Other solidification techniques were also used, including uniform slow cooling of the entire specimen and rapid freezing. The microstructures of specimens produced by these techniques frequently differed appreciably from similar compositions prepared by zoning. A variety of nonequilibrium microstructures characterized by long needlelike particles resulted from the rapid-freeze method. PHASE EQUILIBRIA The lack of information on phase equilibria is a major difficulty associated with a comprehensive study of the Ag-Sb-Te system. Considerable confusion has resulted from the use of the formula AgSbTe, to identify the cubic ternary intermediate phase even though it has been established that material of this stoichiometry normally contains AgzTe as a second phase.798 In this paper, silver antimony telluride will denote the cubic ternary intermediate phase comprising the major portion of AgSbTe,. The term "single phase" will denote material which consists of only the cubic phase (as evidenced by metallographic examination and X-ray diffraction) and the term heterogeneous will describe multiphase material containing AgzTe, SbzTe3, or other phases in addition to the cubic phase. The single-phase material may actually contain a variety of inhomogeneities—gradual changes in composition on a macroscopic scale, localized fluctuations in composition, clusters or other products of early stages of the precipitation process, and a variety of point and line defects—all of which will not be detected by the present techniques for determining homogeneity. Single-phase material has been prepared from compositions close to 59 mole pct SbzTe3 21 (this notation refers to the location on the Ag,Te-Sb2TeS vertical section). Zone widths of =2 cm and growth rates 51.2 cm per hr were used. The single-phase region at elevated temperatures extends off the vertical section to a composition which can be expressed approximately as Ag,,SbzgTes,.9 The latter two compositions as well as AgSbTe, are represented in the conventional Gibbs triangle in Fig. 1. It is not presently possible to ascribe exact values to the limits of the single-phase region on a given isotherm or vertical section due to the extremely

Jan 1, 1964

By Benjamin C. Koskiniemi

Introduction When evaluating any ore body, one of the first questions concerns the ore reserves. In the case of an open pit mine, this is not possible to answer reliably until the ultimate (final) pit limits have been established. Techniques used in designing an ultimate pit are classed as (1) manual, (2) computer, and (3) combined manual-computer. This chapter will describe how manual techniques can be utilized in designing an ulti¬mate pit Certain economic and design criteria must be established before the actual design begins In order to begin designing an ultimate pit, it will be assumed that the engineer already has the following data available (1) vertical sections, (2) horizontal sections for each level, (3) stripping curve, (4) bench height, (5) bank slope angle between levels, (6) level berm width, (7) roadway width, (8) pit slope angles at ultimate pit limits (estimated average including roads and ramps and between roads and ramps), and (9) minimum width of pit bottom

Jan 1, 1979

By S. G. Epstein

Using the capillary-reservoir technique, electromi-gvation rates of cadmium and indium in liquid bismuth were measured at several temperatures. The electric mobility of cadmium Jrom 305° to 535°C and indium from 310° to 595°C can be expressed as a function of temperature by the equations UIn = 1.52 x 10-3 exp sq caz per v-sec Migraion of both solutes was cathode-divected at a rate rnore than four tiMes tHAt previously found for siluer in liquid bisnmth. The electric mobilities of cadmium and indiulrz in liquid bismuth at 500° C are nearly identical with their respective mobilities in mercury at room temperature. AS part of a systematic study of the variables which are considered to control electromigration in liquid metals, the electromigration rates of cadmium and indium in liquid bismuth have been measured. Mass transport properties of silver in liquid bismuth have been reported previously,&apos; and measurements of tin and antimony in liquid bismuth are forthcoming. Comparisons will be made with literature values for these same solutes in mercury.2&apos;3 This series of solutes was selected to determine the effect of the solute valence on its electromigration. Silver, cadmium, indium, tin, and antimony have nearly equal atomic masses but have chemical valences ranging from +1 to +5. They are all fairly soluble in bismuth above 300°C and all have radioactive isotopes, which are an aid in making analyses. EXPERIMENTAL TECHNIQUE Electromigration of cadmium and indium in liquid bismuth was measured by the modified capillary-reservoir technique previously described.&apos; In this method irradiated cadmium or indium is added to bismuth to form alloys containing about 1 wt pct solute (<2 at. pct solute). Several quartz or Pyrex capillaries: 1 mm ID and 5 cm long, vertically oriented, are simultaneously filled in the reservoir of the liquid alloy. A direct current is passed through two of the capillaries, which contain tungsten electrodes sealed in the upper end. The other capillaries sample the reservoir during the experiment. After a measured time interval the capillaries are removed from the reservoir and rapidly cooled. The glass is then broken away from the solidi- fied alloy, which is then weighed, dissolved in acid, and analyzed for solute content by chemical and radiochem-ical techniques. An electric mobility (velocity per unit field) can be calculated from the amount of solute entering or leaving each capillary by the simplified expression1 in which Ui is the electric mobility of the solute, ?mi the solute weight change, Ci the solute concentration of the reservoir, I the current, p the alloy resistivity, and l the duration of the experiment. This expression is valid as long as the experiment is terminated before a concentration gradient develops across the capillary orifice. Earlier experiments showed that the concentration gradient formed initially at the electrode changes with time and eventually reaches the orifice, due to back-diffusion. This condition produces a solute exchange between capillary and reservoir by diffusion or convection, opposing the electromigration, which results in a lower measured value for the electric mobility. To determine if the concentration gradient had reached the orifice, the capillaries used in some of the experiments were sectioned at 1-cm intervals and the solute content of the alloy from each section was radiochemically determined. A typical concentration profile for an experiment with indium in bismuth is shown in Fig. 1; cadmium in bismuth showed similar behavior. As illustrated in the graph, very little back-diffusion has occurred in the capillary containing the cathode, since the concentration gradient is confined to the upper 1 cm of the capillary. In the capillary containing the anode, however, the concentration gradient is much broader, extending nearly to the orifice, even though the net change in solute concentration is nearlv the same in both capillaries. Since cadmium and indium probably lower the density of bismuth when alloyed, depletion of the solute from the alloy adjacent to the anode would increase the density of the liquid in the uppermost region of the capillary. This would give rise to convective mixing within the capillary, causing the broadened concentration gradient. Conversely, the alloy adjacent to the cathode should have a reduced density as the solute concentration is increased by migration, explaining the "normal" concentration profiles found in these capillaries. This disparity was not found for electromigration of silver in bismuth. Both metals have similar densities at the operating temperatures, and nearly symmetrical concentration profiles were found in the two capillaries of each exueriment. This density effect was also apparently encountered when an attempt was made to measure diffusion coefficients for indium in liquid bismuth by the same technique which was successfully used to measure diffusion of silver in bismuth.&apos; Capillaries 1 mm ID and 2 cm

Jan 1, 1968

By Paul Klopstock

(Butte Meeting, August, 1913.) THE Kennedy mining district is situated about 55 miles in a southerly direction from Winnemucca, and about the same distance south-east from Battle Mountain : two towns situated oil t the main line of the Southern Pacific railroad. History. Prospectors were first attracted to the district by the reported discovery of gold by Chinamen in Cinnabar creek in the early 90&apos;s. The prospectors came from the rich placer workings in and about American canyon ; but the new diggings were not found sufficiently rich to justify their being, worked as placer properties, and the prospectors started work in a number of places, looking for the veins which had fed the canyon. In 1893, Charles E. Kennedy, a prospector who had been attracted by the reported discoveries in the vicinity, left Hawthorne and came to the present site of the town of Kennedy. Within a short time he discovered the vein known as the Imperial, and proceeded, with the aid of some friends, to develop it. The vein was readily traced for a distance of about a mile, and about $10,000 worth of high-grade ore was shipped to the Utah smelters. At about the same time the Lawler Brothers, who had been prospecting in the district for some time, located the ?Gold Note group," which showed some extremely rich ore. Within a very short time they extracted from &apos;the Gold Note vein 150 tons of ore, which was shipped to the Utah smelters, and netted about $105 per ton above all expenses. Their good fortune attracted attention to the camp, and within .a short time a town was laid out, with a population of about 500 people. It was named in honor of Kennedy, who had made the first discovery of pay ore in the district.

Jan 6, 1913