Search Documents

By H. J. de Haan, L. Schenk

Scope for Thermal Recovery in Shell's Heavy Oil Fields in Venezuela The main heavy oil reservoirs on the East coast of Lake Maracaibo (Fig. I), known as "Bolivar Coast", initially contained some 20 billion bbl of oil in place with gravities in the range of 10 to 15° API. The current total production rate is about 400,000 B/D. Since the recovery to date is on an average only 12.5 percent of the initial oil in place, these fields offer a vast potential for secondary recovery methods. The reservoirs are characterized by moderate depth (generally 1,000 to 3,000 ft; maximum 5,000 ft), good formation properties such as net oil sand thickness (50 to 300 ft), high porosity (30 to 40 percent) permeability (1 to 3 darcies) and oil saturation (initially about 80 percent) and high oil viscosity (100 to 10,000 cp in situ), all of which are favorable for the application of thermal recovery processes. Since 1957, steam drive, steam "soak" and underground combustion have been tested or are being tested in this area.1-3 This paper deals with a major steam drive test in the Tia Juana field. The test was commenced in Sept., 1961, on the basis of encouraging results of laboratory experiments and pilot field tests, which will be discussed briefly. Early Laboratory Investigation of the Steam Drive Process In 1956 a series of model experiments was carried out in the Koninklijke/Shell Laboratorium, Amster- dam, to investigate the displacement of heavy oil by steam.' The prototype studied was a horizontal, un-consolidated heavy oil reservoir, subjected to a linear steam drive. The model, representing a slab from this reservoir along the main flow direction, consisted of a steel tube filled with oil-saturated sand, provided with layers of rock at the top and bottom to simulate conductive heat losses to cap and base rock. Lateral heat losses, perpendicular to the main flow direction, were minimized by insulating the sides of the model. Heat flow and viscosity and gravity forces were scaled by taking the steam injection rate and sand permeability inversely proportional to the geometric reduction factor of the model, and using materials (oil, steam, cap rock, etc.) identical with those of the prototype. The main feature of the process was a frontal displacement mechanism that was observed within wide ranges of injection pressure and rate, oil viscosity, initial oil saturation and sand permeability. The high stability of this front can be attributed to the high volumetric steam flow rates, combined with the reduction in oil viscosity. High recoveries were obtained due to the low residual oil saturation of about 15 percent in the zone swept by steam. The latter value pertains to the specific test conditions (heavy oil, uncon-solidated sand) and may be lower for light oil, due to the effects of steam distillation. The applicability of this experimental approach is limited, as it does not take into account the fact that

Jan 1, 1970

Upon the recommendation of its Technical Committee, The Com-pressed Air Society has adopted the following definitions of, certain terms. Displacement.-The displacement of an air compressor is the volume displaced by the net area of the compressor piston. Capacity.-The capacity should be expressed in cubic feet per minute, and is the actual amount of air compressed and delivered, expressed in terms of free air at intake temperature and at the pressure of dry air at the suction. Volumetric Efficiency.-Volumetric efficiency is the ratio of the capacity to the displacement of the compressor, all as defined above. Compression Efficiency.-Compression efficiency is the ratio of the work required to compress isothermally all the air delivered by an air compressor to the work actually clone within the compressor cylinder, as shown by indicator cards, and may he expressed is the product of the volumetric efficiency (the intake pressure and the hyperbolic logarithm of the ratio of compression), all divided by the indicated mean effective pressure within the air cylinder or cylinders.

Jan 8, 1918

By Thomas L. Garrard, James A. Sprague, Rex B. McLellan, Samuel J. Horowitz

A simple rnodel for interstitial solid solutions has been devised in which each solute atom interacts with the solzlent lattice in such a way as to exclude an integral number of nearest-neighbor sites from being occupied by solute atoms. The vemaining interstitial sites ave not affected. In calculating the entropy of such a solution the increase in the number of interstitial sites available to solute atoms due to the ozlerlap of blocked sites is taken into account. The ther-modynamic functions and the solute activity fov the solution rnodel are calculated. It is shown that considevation of the overlap sues vise to a correction term of the order 8' ( where 0 is the ratio of solute to solvent atoms) in the thevmodynamic functions of the solution and the solute activity. The theo,uetical equation for the solute activity was used to analyze the available data for the activity of carbon in austenite at three different temperatures. The use of a computer enabled many comparisons to be made between the experimental activity data and those predicted by both the complex blocking model and the simple, widely used blocking model in which the ozierlapping of blocked sites is not taken into consideration. Even though at the highest concentvations oj carbon the value of 0 is small it is shown that the best fit to the experimental data is found with the complex blocking model. RECENTLY it has been shown by analysis of gas-solid equilibriums that many interstitial solid solutions can be described by the quasi-regular solution model in which the partial energy of solution E, is independent of composition and, apart from a composition-independent term due to nonconfigurational factors, the partial entropy is that of an ideal solution. Dilute solutions of nitrogen in both bcc and fcc iron,' dilute solutions of oxygen and silver,' carbon in a Fe,' and dilute solutions of carbon in ? Fe2 are all quasi-regular. In addition many hydrogen-metal solutions, both dilute and concentrated (with the notable exceptions of the H-Ni and H-Pd systems), can be described by this model.3 However, it has been shown that, at various temperatures, solutions of carbon in ? Fe begin to depart strongly from quasi-regular behavior at low concentrations. A plot of the activity of carbon in ? Fe relative to pure graphite vs atom fraction of carbon (Cc) calculated from Smith's data4 begins to depart from the (nonlinear) plot for a quasi-regular solution at about Cc = 0.02. Several statistical models have been proposed to account for the thermodynamic behavior of carbon in y Fe. Darken and smith4 set up a model in which a carbon atom in its octahedral site in the fcc lattice has either one or no neighboring carbon atoms in the twelve nearest-neighbor octahedral sites. It is assumed that the number of carbon atoms having more than one nearest neighbor is negligibly small and that a solute atom does not interact with another solute atom located at a greater distance than the first shell of interstitial sites. Thus this model contains two characteristic interaction energies. Darken and Smith showed that this model gives reasonable agreement with the measured variation of carbon activity ac with composition. It is noteworthy that Darken and Smith concluded from their analysis of the activity data using this model that there was a repulsive force between carbon atoms in austenite which reduces the concentration of C-C pairs below that corresponding to random mixing. Recently Aaronson, Domian, and pound5 have considered in detail the statistical model developed by Lachere and by Fowler and Guggenheim7 and have shown that it is compatible with the activity data for carbon in austenite. In Darken's model the energy of solution of carbon in austenite is dependent on temperature and concentration; the departure from Henry's law arises from the concentration dependence of the energy of solution. In Aaronson, Domian, and Pound's discussion of the Lacher, Fowler, Guggenheim model the interaction energy wy between adjacent carbon atoms in austenite is strongly temperature-dependent. Aaronson et al . suggested that this temperature dependence of wy and hence the energy of solution of carbon could be explained either by the formation of clusters of carbon atoms (despite the repulsive nature of wy) or by the dual occupancy of the octahedral and tetrahedral sites by the carbon atoms. However, a temperature-dependent heat of solution

Jan 1, 1968

By T. B. Counselman

AfteR several years study, the Universal Atlas Cement Co. decided to rebuild its plant at Leeds, Alabama. The entire old plant, which was to operate during the new construction, was then to be scrapped with the exception of two kilns. The quarry was to be mechanized, new and larger kilns installed, with the most modern type of equipment all through the plant. Raw grinding operations at all of the Universal Atlas plants were dry. However, the dust hazard of this operation and the growing emphasis on occupational diseases made wet grinding attractive. Coal at Leeds is cheap, so that a slightly higher coal practice was unimportant. Power was cheap, so that waste-heat boilers were not desirable. Since new kilns were to be installed, these could be made long enough to make filters unnecessary. Wet raw grinding could be either the old practice of open-circuit compartment mills or closed-circuit grinding in accordance with metal-lurgical practice. The latter saved power and steel wear and saved initial investment. This had been demonstrated in cement plants. Also, the elimination of tramp oversize was a most important advantage. Ease of chemical control was another factor. Blending in the thickener, with elimination of slurry mixers had been found practicable. Therefore, if wet raw grinding were used at all, the advantages were clearly in favor of closed-circuit grinding. Detailed layouts of the most modern possible closed-circuit dry-grinding plant and of a closed-circuit wet-grinding plant were prepared, and careful estimates were made of initial investment and operating costs. Full consideration of all the factors involved resulted in a decision to install wet closed-circuit grinding. The capacity of the new kilns was established at 4000 bbl. per day. Two new kilns were installed, each with a capacity of 80 bbl. per hour. Since 625 lb. of raw material is required to make a barrel of finished cement, the capacity of the grinding plant for the new kilns had to average only 1250 tons per day. Sufficient additional grinding capacity had to be provided for the two remaining old kilns, or their possible replacement by a third new kiln. The grinding rate, therefore, was set at 90 tons per

Jan 1, 1939

By T. B. Counselman

AfteR several years study, the Universal Atlas Cement Co. decided to rebuild its plant at Leeds, Alabama. The entire old plant, which was to operate during the new construction, was then to be scrapped with the exception of two kilns. The quarry was to be mechanized, new and larger kilns installed, with the most modern type of equipment all through the plant. Raw grinding operations at all of the Universal Atlas plants were dry. However, the dust hazard of this operation and the growing emphasis on occupational diseases made wet grinding attractive. Coal at Leeds is cheap, so that a slightly higher coal practice was unimportant. Power was cheap, so that waste-heat boilers were not desirable. Since new kilns were to be installed, these could be made long enough to make filters unnecessary. Wet raw grinding could be either the old practice of open-circuit compartment mills or closed-circuit grinding in accordance with metal-lurgical practice. The latter saved power and steel wear and saved initial investment. This had been demonstrated in cement plants. Also, the elimination of tramp oversize was a most important advantage. Ease of chemical control was another factor. Blending in the thickener, with elimination of slurry mixers had been found practicable. Therefore, if wet raw grinding were used at all, the advantages were clearly in favor of closed-circuit grinding. Detailed layouts of the most modern possible closed-circuit dry-grinding plant and of a closed-circuit wet-grinding plant were prepared, and careful estimates were made of initial investment and operating costs. Full consideration of all the factors involved resulted in a decision to install wet closed-circuit grinding. The capacity of the new kilns was established at 4000 bbl. per day. Two new kilns were installed, each with a capacity of 80 bbl. per hour. Since 625 lb. of raw material is required to make a barrel of finished cement, the capacity of the grinding plant for the new kilns had to average only 1250 tons per day. Sufficient additional grinding capacity had to be provided for the two remaining old kilns, or their possible replacement by a third new kiln. The grinding rate, therefore, was set at 90 tons per

Jan 1, 1939

By John Nunes, Frank R. Larson

Temperature-dependent functions of various ten-sile flour stress and fracture parameters were investigated on iron and low composition alloys of Fe-C, Fe-Cr, Fe-Mn, and Fe-Ni. Data were obtained over a range of test temperatures from 200" to -196"C at an initial strain rate of 0.01 min". It was found that the strain-hardening exponent, n, for the Fe-Ni alloys increased significantly at very low testing temperatures with increased alloy addition. Also, the stress and strain at fracture followed a predictable transitional type of behavior. The flour stress-temperature dependence was evaluated employing the relation: M where it is shown that composition can strongly influence the constant M. An empirical formula describing this effect is as follows: M = MI (equivalent at. pct Ni)-'" Some preliminay, tests were run on several commercial steels to test the generality of this relationship. One of the phenomenological explanations of the ductile-to-brittle transition encountered in bcc metals is based upon the difference in the temperature dependence of the flow and fracture stresses.' It states simply that the fracture stress is relatively insensitive to temperature and that the yield or flow stress rises rapidly with decreasing temperature so that, when the flow stress reaches the fracture stress, brittle fracture occurs without appreciable plastic deformation. This behavior is illustrated schematically in Fig. 1 where the ductile-to-brittle transition is shown to occur at two possible temperatures. The lowest temperature, TB, represents essentially completely brittle behavior while the higher temperature, TN, represents "notch" brittle behavior. Support for this theory is obtained when it is observed that fcc metals, which do not commonly have a ductile-to-brittle transition, also do not commonly exhibit any strong temperature de- pendence of the yield stress. This relationship of yield or flow stress behavior with the ductile-to-brittle transition has been generally observed for most metals representative of these two crystallo-graphic structures. One exception to this generalization appears in the case of tantalum where no apparent ductile-to-brittle transition has been observed. However, this may simply be an indication that this type of behavior is not directly related to the flow stress and that some other mechanism such as twinning must also be operative. A comparison of the typical temperature dependence of the yield stress of some representative metals is shown in Fig. 2. In the study of the temperature dependence of the strength of metallic materials, considerable ef-

Jan 1, 1963

By G. Reinberg, C. D. Clarke

Most underground mining operations are dependent on pumping installations to keep the mine unwatered. The reliability of such installations is obviously of paramount importance. The volume of water to be handled is often considerable, and the total head is relatively high. In these cases, both capital cost and operating expense of the pumping installations will become significant factors in overall mining costs. To insure reliability and to keep efficiencies, and hence operating costs, within acceptable limits it goes without saying that mechanical maintenance of a mine pumping installation must receive scrupulous attention at all times. Large mine pumping installations today almost invariably use multistage centrifugal pumps, since positive-displacement units would not be economically competitive except under very unusual conditions of small volume combined with extremely high heads. Centrifugal pump maintenance, under ideal circumstances, would be confined to parts subject to normal running water, i.e., bearing surfaces, stuffing box packing, and shaft sleeves. Under adverse conditions, however, metal may be lost from the wetted surfaces of a pump by erosive or corrosive action of the pumped fluid, and maintenance costs can easily attain enormous proportions.

Aug 1, 1956

AIME 1953 DIRECTORY SUPPLEMENT COMMITTEES NOMINATING E. H. Rose, Chairman R. E. Byler J. F. Myers Grover Molt S. W. Engelmann S. J. Swainson EDUCATION A. C. Dorenfeld, Chairman G. P. Lutjen A. E. McHugh H. Rush Spedden T. G. Chapman T. M. Morris T. Barker S. R. B. Cooke W. O. McClintock

Jan 1, 1953

By Jerry Tien

Mine regulators are normally used for proper air distribution in underground mines. They are deliberately introduced resistance in the regulated airway, and by altering sizes, they can distribute specific air quantities to regulated splits and free splits (4, 5). The enactment of the Federal Coal Mine Health and Safety Act of 1969, the Federal Mine Safety and Health Amendments Act of 1977, and the regulations adopted by the Mining Enforcement and Safety Administration (now called the Mining Safety and Health ministration) prompted greater discussions of optimal mine regulator locations because of the Act's stringent ventilation requirements (2, 3). For example, by requiring the separation of the air used in the belt haulage entries from the intake and return airways, the regulations required the creation of a third type of airway---the neutral airway, as opposed to the intake and return airways, adding to the complexity of a mine's ventilation network. It is the intent of this report to show that panel regulators should be located in intake airways at the neck of a panel for a blowing fan system and in return airways at the neck of a panel for an exhausting fan system in order to achieve optimal air control. A computer simulation model is used to determine optimal mine regulator location.

Jan 1, 1983

By Hisaaki Takada, Atsushi Yoshida, Kazuo Satoh, Norikazu Nanko, Naoshichi Higashi

Kamioka Mine of Mitsui Mining & Smelting Co., Ltd. is the largest lead-zinc mine in Japan and is composed of two mines, Tochibora Mine and Mozumi Mine, which have daily production rates of 5,200 metric tons and 1,800 metric tons of crude ore respectively. In the mines, there are many massive pyro-metasomatic deposits which have been derived from the replacement of limestone. The deposits are composed of skarn minerals which mainly contain hedenberite. The country rock is generally hard and fine-grained gneiss. These deposits have been mined by means of the sublevel stoping method, induced block caving method and sublevel caving method at Tochibora Mine and mainly by the cut and fill method at Mozumi Mine. Since the 19601s, the trackless mining system has been introduced successfully into both mines, and is still promoted to be applied over wider areas. The underground hauling system is simplified remark- ably and much improved by adopting trackless ramps to the existing vertical and horizontal underground framework. Moreover, through the combination of the trackless mining system with the mining methods stated above, a notable increase in efficiency has been achieved. This is due to the high performance of the introduced machinery, reductions in man power of miscellaneous jobs, and also has enabled a highly efficient performance through its mobility. In addition, as it becomes possible to realize a flexible development to meet the irregularly shaped deposits and also becomes much easier to recover the remaining pillars by secondary mining, the extraction rate of ore has been improved considerably. With the introduction of the trackless mining system, the development method has been changed, thus former hand-hold leg-drills are now mostly re- placed by jumbo-type drills. Repair shops for Load-Haul-Dump machines also have been provided with an established service system. Reinforcement and rearrangement of the ventilation system has been carried out.

Jan 1, 1977

Institute of Metals Iron and Steel Mineral Industry Industrial Minerals Year Division Petroleum Division Division Coal Division Education Division Division 1918 W. M. CORSE ' 1919 " 1920 W. H. BASSETT 1921 1922 W. B. PRICE RALPH ARNOLD 1923 E. DEGOLYER 1924 G. K. ELLIOTT 1925 " F. JULIUS FOHS 1921; PAUL D. DIERICA " 1927 JOHN M, LOVEJOY 1928 S. SKOWRONSKI A. W. AMIBROSE RALPH Fl. SWEETSER 1929 " J. B. UMPLEBY G. B. WATERHOUSE 1930 ZAY JEFFRIES C. V. MILLIKAN \V. J. MACKENZIE HOWARD N. EAVENSON 1931 SAM TOUR C. E. BEECHER F. AT. BECRET 1932 C. H. MATHEWSON EARL OLIVER F. N. SPELLER THOMAS G. FEAR , C. H. FULTON 1933 T. S. FULLER W. E. WRATHER JOHN JOHNSTON ELI T. CONNER 1934 .J. L. CIIIRISTIE H. D. WILDE, .JR. L. F. REINARTZ T. T. READ 1935 W. M. PEIRCE HARRY H. POWER A. B. KINZEL JOHN T. RYAN SAMUEL H, DOLBEAR 1936 E.H. DIX,JR. HALLAN, N. MARSH C. E. WILLIAMS EUGENE McAULIFFE WILLIAM B; PLANK' OLIVER BOWIES 1937 A. J. PHILLIPS AL ALBERTSON FRANCIS B. FOLEY J. B. Moscow " CHESTER A.. FULTON 1938 R. F. MEHL G. B. CORLESS J. T. MACKENZIE PAUL WEIR FRANCIS A.THOALSON J. R. THOENEN 1939 R. H. LEACH W. I-1. G E I S J. HUNTER NEAD C. A. GIBBONS " AT. M. LEIGHTON 1940 C. A1. WISE T. V. MOORE F. T. SISCO C. E. LAWALL W. R. CHEDSEY W. M. WEIGEL 1941 D: K. CRAJIPTON E. A. STEPHENSON C. H. HERTY, JR. JULIAN E. TOBEY " . PAUL AT. TYLER 1942 CARL E. SWARTZ HARRY P. STOLZ E. C. SMITH NEWELL G. ALFORD A. F. GREAVES-WALKER B. L. MILLER 1943 CYRIL STANLEY SMITH C. A. WARNER HERBERT W. GRAHAM CADWALLADER EVANS, JR. " HOWARD 1. SMITH 1944 ARTHUR PHILLIPS W. S.-MORRIS WILLIAM A. HAVEN A. W. GAUGER A. C. CALLEN C. H. BEHRE, JR

Jan 1, 1944

Pulverized Fuel Combustion The apparatus shown in the illustration is a complete equipment f r supplying coal to boiler and metallurgical furnaces, cement and lime kilns, dryers, and to all furnaces requiring a temperature and quality of fame under prompt and easy control. It is claimed that the Aero Pulverizer makes practicable the highest efficiency obtainable from burning coal. It makes coal burn like a gas, a flame, the physical and chemical character of which is regulable- a flame that may be elongated or shortened, thus placing the zone of highest temperature where needed- a flame that may be made oxidizing, reducing, or neutral, as occasion may require. The coal is burned as pulverized, and there is no storage of the powder with its attendant hazard. Artificial drying before pulverizing is not necessary if the coal supply be sheltered from rain and snow. Where the Aero is used, it is wholly a furnace question whether a dryer should be installed; it is not at all a pulverizing or storage question. Labor is reduced to a minimum. Slack coal at low cost yields its last B.T.U.

Jan 11, 1915

By Gerald Greene

Tan various lead producers have given the subject of lead drosses much attention in recent years but the problem of their economical treatment is yet to be solved. Formerly the copper in the furnace feed was removed from the furnace in the form of matte. The speiss at that time consisted principally of the iron arsenide. The practice today is to roast off most of the sulfur and the copper in the feed forms a dross in the furnace, which is removed from the furnace with the lead. This material is poured into the drossing kettles and allowed to cool down to but slightly above the freezing point of lead. The copper dross, containing almost all of the arsenic and part of the antimony, is skimmed off and treated in a small reverberatory furnace at most plants. This is essentially a liquation process. The skimmed dross contains from 70 to 80 per cent lead, and much of this lead is liquated out. The products from this treatment are: (1) impure lead, (2) speiss and (3) matte. The speiss from the reverberatory furnace was studied in this research. The literature on the subject is of very little assistance, as almost no work has been done on the problem of establishing the exact identity of the various phases present. One author(1) states that speiss consists of a series of isomorphous compounds of the general formula FexAsy in which the Fe may be replaced by Ni, Co, Cu, Pb, Ag, Au, Pt, Zn, Cd and the As replaced by Sb, S and Bi. Hofman(2) states that the iron arsenide present is Fe5As.

Jan 1, 1935

By P. H. Metzger, D. W. Fuerstenau

The activation of sphalerite was found to occur at a much lower rate with Pb++ then with Cut++ or Ag+. To prevent activation with Pb++, the ratio [m in solution must approximate 103. An example is given illustrating how this condition is met in practice through the addition of zinc sulfate and soda ash. In selective lead-zinc flotation, the mill operator, especially the one who is concentrating a partially oxidized ore, often must add zinc sulfate and/or soda ash for effective depression of the sphalerite. In the present paper the authors show how this practice prevents the activation of sphalerite in the presence of Pb++. A number of years ago Gaudin (1) postulated that Zn++ might control the activation of sphalerite with Pb++ through competitive adsorption. However, recent experimentation has shown the activation of sphalerite with Ag+ and Cut++ to be a chemical reaction in which silver or copper ions replace zinc in the sphalerite lattice through the formation of a more insoluble sul-fide (2,3,4) Thus, if activation with Pb++ is similar to that with Ag+ or Cu t+, zinc salts should control the activation of sphalerite not through competitive adsorption but because the ratio of [zn++/Pb++] in solution regulates the extent of the chemical exchange between Zn++ and Pb++ in the solid phase. The objective of this investigation has been to study the kinetics and equilibrium conditions for the uptake of Pb++ by sphalerite and to investigate the prevention of lead activation with zinc salts. BASIC PRINCIPLES Sphalerite activation has been shown to be a replacement reaction wherein a less soluble compound is formed at the expense of the more soluble zinc sul-fide (2,3,4) For example, if sphalerite is placed in an aqueous silver nitrate solution, ZnS gives to the solution more S= than can exist together with Ag+, and hence the following reaction takes place: ZnS + 2 Ag+? Ag2 S + Zn ++; k = [zn ++]/[Ag ++]2 = 10 26 (1) Therefore, ZnS will dissolve in the presence of Ag+ and activation of sphalerite with Ag+ will proceed after monolayer coverage by solid state diffusion until equilibrium conditions are reached in the system (2, 4) Because of the large difference in the solubility of ZnS and Ag2S, zinc salts cannot affect the reaction unless a complexing agent, such as cyanide ions, is present to complex Ag+ more tightly than Zn++ . By complexing Ag+ and Zn++ in solution, the uptake of Ag+ by sphalerite can be regulated by controlling the ratio m. . Experimentally (2) it was found that the activation of sphalerite by Ag+ could be prevented through the addition of NaCN if this ratio reached a value of approximately 10 26. The mechanism of sphalerite activation with copper salts is given by the following reactions: ZnS + Cu ++ ? CuS + Zn + + ; (2) k = [Zn++]/[Cu++] = 10 11 ZnS + Cu + ? Cu2S+ Zn++; (3) Experimentally Mao (3) found that the activation of sphalerite with Cu++ or Cu + was prevented if the ratios expressed in Equations 2 and 3 were approximately l09 and l022, respectively, with cyanide ions as the deactivator. Although zinc salts do not affect the activation of sphalerite with silver or copper ions in the absence of a complexing agent, activation with lead ions theoretically can be controlled by the addition of zinc salts because of the relatively small differences between the solubility of ZnS and PbS (5). Equilibrium

Jan 1, 1961

By G. F. Olsen

ON superficial consideration a technical library might be considered a luxury to the business institution that possesses one. After all, public libraries and research institutions probably contain all the data that would be found in a private technical library, and able consultants are available both within and without a company. In all probability the technical men of a company have in their combined personal libraries sufficient information to answer most inquiries. Nevertheless, possession of such a department is of real economic benefit because of the time it saves its users, because it prevents expensive duplication of technical literature in a company, and lastly, but most important, be- cause it makes readily available a central storehouse of technical facts classified and indexed to meet the demands of the industry or industries concerned.

Jan 1, 1940

By Raymond B. Ladoo

NONMETALLIC minerals (excluding fuels) arid their primary products produced annual in the United States have a value in excess of one billion dollars, or more than that of the metals, yet the lack of expert knowledge of some of the fundamental technical and economic aspects of this most important and complicated business is astonishing. This paper will deal with the economics of this non- metallic mineral field-the business of making money from producing these minerals. The incentive behind all business activity in a capitalistic economy is to make money-to plan so that each dollar invested in property, plant, equipment, services, and so on will return more than a dollar plus simple interest. Of course, business has social, civic, and national duties and responsibilities, but the fulfillment of these is largely dependent upon financial success.

Jan 1, 1939

By G. Beghi, G. Piatti

THE authors examined the problem of the gradual transformation of Al2O3 from the transition phases normally encountered in SAP (r -x-n)1-3 to the stable a phase. This phenomenon is well-known at temperatures above the melting point of aluminum,3"6 whereas in this paper the transformation was studied at temperatures lower than the melting point of the aluminum matrix.

Jan 1, 1967

By B. A. Eaton

The subject of many discussions and technical papers in the last 20 years has been the prediction of the well-bore pressure gradients that are required to induce or extend fractures in subsurface formations. The subject merits this attention because of the frequently recurring problems that arise from an inability to predict fracture pressure gradients. Encountered in several common types of operations in the oil industry are problems associated with the prediction of formation fracture pressure gradients. When wells are being drilled in both new and old fields, lost circulation is often a very troublesome and expensive problem. Complete loss of circulation has been disastrous in some cases. Many times, such disasters could have been avoided if techniques for calculating fracture pressure gradient had been employed in the well plans, and if casing strings had been set, and mud weight plans had been followed accordingly. In areas of abnormally pressured formations, the prediction of fracture gradients during the well-planning stage is extremely important. In fact, it is as important as the prediction of formation pressure gradients, which has received a great deal of attention in recent years. There are several published methods used to determine fracture pressure gradients. However, none of these methods appears to be general enough to be used with much reliability in all areas. In 1957, Hub-bert and Willis published a classical paper that included the development of an equation used to predict the fracture extension pressure gradient in areas of incipient normal fau1ting.l Overburden stress gradient, formation pore pressure gradient and Poisson's ratio of rocks were the independent variables that were shown to control fracture pressure gradient, the dependent variable. In 1967, Matthews and Kelly published another fracture pressure gradient equation that is different from that of Hubbert and Willis in that a variable "matrix stress coefficient" concept was utilized.3 Later the same year, Costley wrote about a similar idea.5 Goldsmith and Wilson used a least-squares curve-fitting technique and field data from the Gulf Coast area to correlate fracture pressure gradient with formation pore pressure gradient and formation depth.' They noted that the fracture pressure gradient increased with increasing depth while the pore pressure gradient remained constant. In each of these cases, the problem for which a solution was sought was to determine the bottom-hole pressure gradient required to initiate or extend a fracture. Results of the previous work show that fracture pressure gradient is a function primarily of overburden stress gradient, pore pressure gradient, and the ratio of horizontal to vertical stress. There is argument for a fourth variable in that in many cases breakdown fracture pressure gradient is greater than the fracture extension pressure gradient. However, if the fracturing fluid is able to penetrate the formation through the pores or existing cracks, there is very little

Jan 1, 1970

LIST OF MEMBERS AND ASSOCIATES ARRANGED ACCORDING TO STATES AND TOWNS ALABAMA Aldrich, Aldrich, W F Anniston, Noble, A E, Smith, N B Aibacoche, Bradley, D II Bessemer, Fergusson, V Birmingham, Aldrich, T H, Aldrich, T H, Jr, Bowron, J, Bowron, C E, Davis, F H, Dimmick, F D, Hillman, McCarthy, M E , McCormack, McCrery, Ramsay, E, Shook, A M Bridge¬port, Wheeler, S K Ensley, McDonald, S, Shook, J W Fanbanks, Hamil¬ton, A L Helena, Squire, J Huntsville, Moss Lehigh, Toulmin Oxmoor, Green¬amyer, A G Plasma, Gage Rock Run, Garvin Sheffileld, Miller, D I Tuscaloesa, Lodge, J University, McCalley Woodward, Bukofzer, Woodward, A H ALASKA Dawson, Buck Douglas Island, Corbus, J P , Macdonald, J Hames, Le Wald, E A Jualin, Hoggatt, W B Juneau, Denby, Gaifield, Garside, Hamp¬ton, W H Rodman Bay, Phillpots Snettisham, Tisdale Sumdum, Thane Tel¬ler, Hirshberg, M R Treadwell City, Batcheller, J H , Kinzie Valdez, Esterly, G M Yukon, Dawson, Elmer, J M ARIZONA Bisbee, Clark, G C, Coombs, H L , Douglas, W, Hoatson, Parnall, S A, Pelton, R T, Ricketts, L D, Sherman, G F G, Smith, F W, Smith, H A Black Diamond, Bagge Blanchard, Cummins, Murray, J J Casa Grande, Rich¬mond, A B Clifton, Colquhoun, Grabill, Murray, H T , Plater, Smith, J D A, Veitch, Watson, W S Congress, Goodloe Crown King, Alexander, G E Douglas, Cornell, Kraemer, E L, Lee, G B, Rutherford, F Globe, Berray, Hoar, Snell Harrisburg, Smith, F C Jerome, Clark, W A, Thomas, C A Kingman, Treadwell, Wallace, J P Kirkland, Bretherton, G K Kofa, Lamp¬shire, J O , Pomeroy, H G Mayer, Haggott, E A Metca j, Blumenkranz, M , Forbes, D L H Morenca, Clark, C D, Fleming, J B, Honey man, Mills, C E, Wallace, L R Morristown, Stevens, H W Nogales, Glove, H G, Sandoval, A , Sandoval, P Octave, Rose, G W Phoenix, Armstrong, T , Butler, C E, Defty, Lindsay, L Prescott, Blauvelt, H , Bunker, C E, Claypool, W M , Drescher, F M , Fairbank, Nissen Tombstone, Gage, Poindexter, C L , Staunton, Walker, E W Troy, Cutting Tucson, Blake, W P, Burgess, De Lashmutt, I, McCleary, Mann, Prout, J W , Jr ARKANSAS Fayetteville, Purdue Fort Smith, Bache, F , Denman, H Little Rock, Fordyce, Scholz CALIFORNIA Alameda, Arents, King, L Arnador City, Downs, Tregloan Angeles Camp, Dig¬gles, R N , Kenney, C E Antioch, Belshaw Auburn, Coe, I J Ballarat, Thorns Berkeley, Abadie,, Christy, Dozier, Hall, F F , Hersam, Landfield, Lind¬say, L , Mansfield, N T, Morley, W S , Sharwood, W J Bag Oak Flat, Dron Bodae, Hamilton, W R, Hoover, T, Hoover, T J, Jackson, B L , Nutter , E, H Bullion, Power, H T Callahan, Scott, E H Campo Seco, Baird Cartero,

Jan 1, 1910

INTRODUCTION Engineering studies of many near surface coal deposits that are amenable to strip mining can be enhanced and expedited by the application of computer techniques for defining coal reserves and overburden and intraburden yardage and their stripping ratios. The case study discussed herein could be from the western coalfields of Colorado, Wyoming, or Montana; the lignite deposits of the Dakotas or Texas, or from the strippable coal seams of the midwest. Because the techniques can be applied so universally, the actual map locations are not identified. The same computing principles apply to one seam or multiseam deposits, and the capability of the computing programs and plotting routines to display the coal seams in plan and sections provide excellent base maps for further engineering planning and mine layout studies. MANAGEMENT OF DRILL HOLE DATA Drilling for coalfield information is usually done at much wider centers than for other mineral deposits. The geologic logs of the holes are generally quite simple, and frequently record only major lithologies and depths to the top and bottom of the coal seams, together with hole collar survey information. A header card is prepared for each drill hole showing: Hole ID Northing Fasting Elevation Azimuth Dip The header card can be followed by any number of downhole lithologic intercept records: [Hole Depth Lithology Hole ID From-To Coal] Less data errors occur if the computer cards are punched directly from drill hole logs, thus eliminating opportunities for mistakes in transcribing data. All arithmetic manipulations should be left to the computer to avoid as much human error as possible. The SURVEY program is run over the raw data file and all lithologic intercepts are computed and defined in XYZ space. BOUNDARY SURFACES-COAL SEAMS AND LITHOLOGIC UNITS The most useful computer program for defining coal seams in 3D space is a linear inter-

Jan 1, 1980