Search Documents

By Rollin Farmin

Rock pressure against the supports for underground workings in certain mines becomes sufficiently severe to crush sound timbers. The cost of maintenance of these mines increases critically as the workings are extended. "Heavy ground " and "swell-jng ground" are terms commonly applied to a condition of excessive pressure from the wall rock. Defined for the purposes of this paper, "heavy ground" delivers gravi-tative pressure on the supports of a mint opening; "swelling ground" delivers pressure arising from expansion of the wall rock. Mining problems created by heavy ground have been studied extensively by mining engineers, as in the recent Symposium on Block caving.' A parallel study of rock bursts2 attacks the field of ground that ruptures under strain. The problem of swelling ground, which has received less current attention, is the subject of this paper. An ExaMPLe of Swelling Ground Severe cases of swelling ground are found in the gougy shear zones in mines along the western Sierra Nevada, where the veins are accompanied by faults through altered serpentine, schist and slate. For example, along troublesome stretches in the ldaho Maryland mine, Grass Valley, California, swelling ground continues to crush drift timbers, with diminishing intensity, for 3 to 10 years after entry. During this period, from five to nine generations of crushed timber sets must be replaced and a large additional tonnage of scaly rock and wet gouge must be removed from the drift to make room for this succession of new timbers. After "the squeeze has been taken out of the ground" the timbers will stand for years, until they collapse from decay. Heaving of floor and footwall along drifts develops soon after the timber sets are placed and frequent grading down of the track is necessary to keep it serviceable and to maintain headroom. If sills are placed under the drift posts, the sets break more quickly and the track becomes impassable at once. When the floor is left Open? and the bottoms of posts and stulls are pencil-pointed, the scaly ground of the fault zone swells up around the timbers (Fig. I) instead of breaking them (Fig. 2). A foot or two of this encroaching ground is trimmed from the floor and lower sides of the drift several times before complete retimbering is necessary. when a set of timber fai1s under the Pressure of swelling ground, there is no immediate fall of timber and broken rock to fill the drift, as is customary in heavy, caving ground. Instead, ground swelling from sides, top and bottom gradually closes the opening, over a period of weeks or months, and no especial hazard to workmen is present while they have room to walk through the narrowing drift. Most

Jan 1, 1946

By Bain, Edgar C.

THE results are presented of an investigation to discover the fundamental atomic conditions existing in Corson's high-copper alloys hardenable by means of silicide solution and reprecipitation. The study attracted the writer because it offered a very convenient example of the general type of hardenable alloys exemplified by duralumin. Sykes' iron-tungsten and iron-molybdenum alloys and the hardenable lead-antimony. SUMMARY OF RESULTS AND CONCLUSIONS In brief, the investigation shows that very perfect crystallinity exists in the solid solutions prepared at high temperature to contain as much dissolved silicide as possible. The lattice parameter of copper is altered very little by the amount of cobalt, nickel or chromium, and silicon dissolved. The hardening by drawing at a temperature to initiate precipitation of excess silicon and metal produces a remarkable change in the atomistics of the solid solution. The old perfection of crystallinity in the solid solution is destroyed and the new atomic spacings are of variable magnitude even in one grain, and a condition in a measure resembling that found in martensite is observed. Were no particles whatever precipitated by the drawing action, still ample causes for hardness would be in evidence in the solid solution alone. The lack of plane continuity in the crystal grains would oppose slip in a very effective manner. Complete annealing restores the crystalline perfection in large measure. In these alloys even the most sensitive methods failed to reveal the characteristic pattern of the silicide precipitated by the anneal, but this was largely to be expected as the amount is relatively small.

Jan 1, 1927

By E. C. W. Perryman

The recovery of X-ray line broadening, hardness, and electrical resistivity from cold worked AI-Mg alloys has been investigated. The results, together with those from density measurements, suggest that magnesium atoms freeze in the excess vacancies formed by cold working, and that this affects the climb of dislocations during the recovery process. PREVIOUS work1, " has shown that while 1 pct Mg increases the activation energy for recrystalliza-tion, it decreases the activation energy for the recovery of mechanical properties and decreases the subgrain size both after cold working and annealing. A similar result has been reported by Varley2 for an A1-2 pct Mg alloy. With plastic deformation at high temperatures, McLean and Farmer' and Rachinger have found that magnesium appears to retard the motion of dislocations and, furthermore, they find little or no effect of magnesium on the size of subgrains formed during high temperature deformation. In view of the apparent contradictions as to the effect of magnesium on subgrain size, the recovery process in Al-Mg alloys has been investigated more thoroughly by studying the annealing out of X-ray line broadening, hardness, and electrical resistivity from alloys cold worked at room temperature. Material Used—The chemical analyses of the alloys are given in Table I. Fabrication—The material used was cold rolled 20 pct at room temperature, the grain size prior to the last cold rolling operation being similar to that used in previous work; i.e., 230. The experimental procedure for annealing, determination of X-rav half-veak breadth. hardness measurement, electEica1 resistivity, and density and metallographic examination was exactly the same as previously described." Variation of X-Ray Half-Peak Breadth with Annealing Time—Isothermal annealing curves at 100°, 200°, and 250°C were obtained for material cold worked 20 pct. The half-peak breadth of the (333) Ka, line directly after cold working is shown as a function of magnesium content in Fig. 1. Only with the 2.87 pct Mg alloy was overlapping of the a, and n.. reflections observed to any appreciable extent. To separate these, Rachinger's method' was used. Typical isothermal annealing curves are shown in Figs. 2 and 3 for 100" and 200°C, respectively. These curves are similar to those obtained previously for super-purity aluminum except that the

Jan 1, 1957

By D. D. Porter, H. G. Carlevato

Blasting to prepare orebodies for in situ leaching usually involves extraordinary conditions which sometimes require special and innovative techniques. To date several unusually large blasts have been made for leaching with results that are very encouraging. Among the factors considered when designing these large blasts are orebody shape and depth, rock properties, vibration and damage potential, loading logistics, and safety. All of these factors, and others, are discussed with an effort made to put each of them into its proper perspective.

Jan 1, 1974

By R. I. Jaffee, J. G. Dunleavy, W. Hodge, H. R. Ogden

Early in 1946, at the instigation of the U. S. Army Signal Corps, the authors made an extensive survey of the available literature covering high-strength, high-conductivity alloys. For the purposes of the Signal Corps, the minimum tensile strength to be considered was 150,000 psi, together with at least 50 pct IACS conductivity. No single alloy was found to be in production, or mentioned in the literature, which had this combination of properties. The constitution diagram for the iron-copper alloys is not well established in the respect to the two-liquid region. Fig I, taken from the 1939 Ed. of the ASM Metals Handbook, shows a two-liquid system existing above the liquidus temperature, but disconnected from it. Although Ruer and Fickl and Ruer and Goerensz definitely established the fact that two liquid layers could occur in the system, Ruer3 was not convinced that the line of immiscibility was closed in the center. Maddocks and Claussen4 found no liquid immiscibility at temperatures up to 157oOC in alloys containing almost no carbon. Although the diagram would indicate age hardening of the copper-iron alloys is possible, Hanson and Fords found that little hardening effect could be obtained. However, Gordon and Cohen6 reported that the response is better if the quenching is very efficient. Although iron has a potent effect on the conductivity of copper, Hanson and Fords have shown that, when hot-rolled copper-iron alloys are aged at 1200°F, the electrical conductivity decreases sharply with iron contents up to 0.2 pct Fe, and then levels off at conductivities between 60 to 70 pct IACS with compositions to 2.1 pct Fe. They also found that aging did not increase the tensile strength, although increasing iron content gave a moderate improvement in strength. High-strength copper-iron alloys, usually containing about 60 pct iron, had been reported by Smith and Palmer.7 They found that an alloy containing 56.4 pct copper, 0.21 pct magnesium, balance iron, would give a maximum tensile strength of 170,000 psi and an electrical conductivity of slightly over 35 pct IACS. The alloy could also be processed to have I50,000 psi tensile strength, and about 41 pct I.\CS conductivity. Decreasing the iron content increased the electrical conductivity, but the long mushy range during freezing of the alloy containing 10 to 20 pct iron made the production of good castings difficult. In spite of the difficulty encountered by Smith and Palmer with alloys of around 20 pct iron, it was decided to make a rather complete investigation of this type of alloy. As a result of this investigation, a method of alloying and fabricating copper alloys containing 10 to 15 pct iron was developed

Jan 1, 1949

By G. Sachs, G. Espey

It is well known that high residual stresses are created in tubing by the sinking process, in which no internal tool or mandrel is used.l-4 In this process, the wall thickness is usually slightly increased.4,5 In tube drawing with a plug, the residual stresses are gradually reduced with increasing reduction of wall, and, by the conventional approximation methods of stress measurement, no stress is detected in tubing in which the wall reduction is over 50 per cent of the total reduction in cross-sectional area.l,6 It has also been observed that higher stresses are set up by the use of wide-angle dies than by acute dies.? 'he actual stress distribution in drawn tubing has been investigated by a few workers,7"9 but has not been related to the conditions of the drawing process. Some attempts have been made to correlate accelerated cracking tests for stresses in brass products with the magnitude of the circumferential stresses and the condition of the metal. l-10 Materials and Preparation The material used in this experiment was commercial cartridge-brass (70 per cent Cu, 30 per cent Zn) tubing in the straightened and annealed condition.† This tubing was of various outside diameters and had a wall thickness of 0.032 in. It was sunk to 1/2-in. outside diameter by means of an experimental 10,000-lb. hydraulic draw-bench, with a maximum drawing speed of 8 ft. per minute. All dies were of 1/2-in. diameter. Various die materials and contours were used in order to study the effect of die design on residual stresses in the tubing; the specifications for the dies are given in Fig. I. Castor oil was used throughout as lubricant. Chattering occurred in sinking some of the tubing, particularly when dies having the more acute angles were used, but the tubes showing chatter marks did not differ markedly from those with a smooth surface regarding the magnitude of residual stress. The source of the chattering has not yet been revealed. The wall of the tubing becomes thicker during s nking, as previously observed.4,5 The increases in wall thickness were 3, 7 and 9.5 per cent on the average for 6, 20 and 33 per cent reductions in diameter, no effect of the contour being noticeable. The reductions mentioned throughout this investigation do not consider this fact, but are reductions of the outside diameter. For the evaluation of the residual stress two fundamentally different methods were used. The approximation methodl,ll of splitting a certain length of tubing was employed to obtain a bird's-eye view of the effect of various drawing conditions on the circumferential stress measured by the diameter change occurring On splitting. For

Jan 1, 1942

By G. Sachs, G. Espey

It is well known that high residual stresses are created in tubing by the sinking process, in which no internal tool or mandrel is used.l-4 In this process, the wall thickness is usually slightly increased.4,5 In tube drawing with a plug, the residual stresses are gradually reduced with increasing reduction of wall, and, by the conventional approximation methods of stress measurement, no stress is detected in tubing in which the wall reduction is over 50 per cent of the total reduction in cross-sectional area.l,6 It has also been observed that higher stresses are set up by the use of wide-angle dies than by acute dies.? 'he actual stress distribution in drawn tubing has been investigated by a few workers,7"9 but has not been related to the conditions of the drawing process. Some attempts have been made to correlate accelerated cracking tests for stresses in brass products with the magnitude of the circumferential stresses and the condition of the metal. l-10 Materials and Preparation The material used in this experiment was commercial cartridge-brass (70 per cent Cu, 30 per cent Zn) tubing in the straightened and annealed condition.† This tubing was of various outside diameters and had a wall thickness of 0.032 in. It was sunk to 1/2-in. outside diameter by means of an experimental 10,000-lb. hydraulic draw-bench, with a maximum drawing speed of 8 ft. per minute. All dies were of 1/2-in. diameter. Various die materials and contours were used in order to study the effect of die design on residual stresses in the tubing; the specifications for the dies are given in Fig. I. Castor oil was used throughout as lubricant. Chattering occurred in sinking some of the tubing, particularly when dies having the more acute angles were used, but the tubes showing chatter marks did not differ markedly from those with a smooth surface regarding the magnitude of residual stress. The source of the chattering has not yet been revealed. The wall of the tubing becomes thicker during s nking, as previously observed.4,5 The increases in wall thickness were 3, 7 and 9.5 per cent on the average for 6, 20 and 33 per cent reductions in diameter, no effect of the contour being noticeable. The reductions mentioned throughout this investigation do not consider this fact, but are reductions of the outside diameter. For the evaluation of the residual stress two fundamentally different methods were used. The approximation methodl,ll of splitting a certain length of tubing was employed to obtain a bird's-eye view of the effect of various drawing conditions on the circumferential stress measured by the diameter change occurring On splitting. For

Jan 1, 1942

By W. R. Seyfried

The problem of extracting alumina from clay and low-grade bauxites has been the subject of considerable interest for some time. The basic reason, of course, lies in the fact that known reserves of high-grade bauxite are not inexhaustible and that the present commercial process cannot successfully cope with low-grade bauxites or clay. Ultimately it may be necessary to use these poorer raw materials for all commercial operations. An unprecedented demand for aluminum during the war emergency and the constantly threatened shortage of imported bauxite caused the United States Government to take an active role in this problem. Through the National Academy of Sciences, the War Production Board and the Defense Plant Corporation, it investigated processes and finally selected four to be used in the construction and operation of four experimental plants. Each plant was to be designed in such a way as to facilitate its incorporation into a larger commercial plant should the need arise. The Chemical Construction Corporation process, or "Chemico" ammonium sulphate process as it is better known, was one of the four selected. The extensive literature and patents on record before the war generally follow one of two process-types depending upon the extracting reagent used. One group uses an acid reagent, the other an alkali. The Chemico process uses an acid reagent. For those interested in other processes described in literature, there is a short bibliography at the end of this paper. The basic steps of all acid extraction processes are: (I) to make the aluminum silicates acid soluble, (2) to separate the released alumina from impurities and insoluble gangue, and (3) to recover the reagent for re-use. The Process as Planned In April 1941, a group of chemists and engineers of the Chemical Construction Corp. became interested in the problem of extracting alumina from clays and low-grade bauxites and, under the leadership of Mr. Blakeslee Barnes, Vice President and General Manager of the company, first drafted a process in July of that year—five months prior to Pearl Harbor. The work continued in our research laboratories and with a small pilot plant. By June 1943, the work had progressed to a point where it was possible to apply for a patent on the process which was U.S. patent 2,405,426, granted August 6, 1946. Immediately prior to the development of the Salem plant, the process was envisaged to be as follows: I. The first step was to make the aluminum silicates acid soluble. It was planned: (a) Clay or lour-grade bauxite would be roasted at 700 to 800°C (1292° to 1472°F). (b) The roasted ore would then be leached with hot aqueous ammonium bi-sulphate to form a slurry. In this way the

Jan 1, 1949

By Jay R. Burns

Two magnesium sand-casting alloys are commonly favored in the United States. These are referred to as H and C alloys (Dow Chemical Co.) or AM265 and AM260 alloys (American Magnesium Corporation). Both are of an aluminum-zinc-manganese type. H alloy contains 6 per cent aluminum and 3 per cent zinc and is characterized by relatively good toughness. C alloy contains g per cent aluminum and 2 per cent zinc and is employed where high yield strength and pressure tightness are required. Examination of magnesium castings poured in Europe and England,1,2 however, demonstrates that H and C alloys are replaced by A8 and AZ91, respectively. That is, A8 represents a magnesium alloy having superior toughness while AZ91 is suitable for high yield strength and pressure-tight applications. The basic difference between the American and European alloys is that the foreign alloys employ a somewhat higher aluminum content and less zinc than is found in H and C alloys. The mechanical properties of the alloys, when divided into high and low-aluminum groups, are quite similar, as determined from separately cast foundry-control type test bars.3 In this paper the decrease of mechanical properties caused by any given amount of microporosity is measured for H, C, A8, and AZ91 alloys. The relative susceptibility of each of the four alloys to microporosity is also determined. Typical mechanical properties and nominal chemical analyses are reported in Table I. [ ] The apparent similarities between the two alloys in each group have led to considerable discussion as to the relative merits of each of the compositions.2 Popular points for comparison between the alloys have been the relative susceptibility of each of the four alloys to microporosity5 and the effect of this microporosity on their mechanical properties. It is primarily intended, in this paper, to show the

Jan 1, 1946

By H. Rush Spedden, A. M. Gaudin

ALTHOUGH the number of minerals that are ferromagnetic) or highly paramagnetic is strictly limited, it has been known for some time that many minerals have slight but supposedly characteristic magnetic susceptibilities. With the exception of pyrrhotite, however, sulphides have been thought nonmagnetic. A new magnetic separator has been made available recently in limited quantity to research laboratories. This device, the Frantz Isodynamic Separator, has been used for the separation of various nonsulphides from each other. Its application to the separation of sulphides, however, does not seem to have been reported. In the Richards Mineral Dressing laboratories, the success achieved through the use of this device in separating associated sulphides has been so startling as to lead us to believe that it constitutes a magnificent adjunct to heavy-liquid separation and to quantitative mineragraphy as a tool for the mineral investigator. THE SEPARATOR The separator (Fig. I) consists of: I. A powerful magnet, the strength of which can be adjusted by means of a rheostat; 2. A vibrating chute of nonmagnetic metal on which the mineral to be separated is made to flow (Fig. 2); 3. A feed bin and adjustable feeder; 4. Receptacles for the collection of products; 5. Means for changing, setting, and accurately reading the two slopes of the chute; viz., the cross slope and longitudinal slope. The separator is made operative by the special shape of its pole pieces, which ensures a strongly converging field. It is said by the makers of the machine that the pole pieces apply a constant mechanical force to a particle of given susceptibility, regardless of its position in the operating space of the separators.* Susceptible particles, therefore, behave as though of lower specific gravity than under ordinary circumstances. This effect, combined with the slopes of the chute and the action of the vibrator, causes a stratification not unlike that obtainable on a shaking table. The chute is of rectangular cross section, and shallow; it is broadened toward the discharge end and divided longitudinally by a partition into two compartments that lead to the collecting receptacles. Although the separator probably can be used to make separations at fairly coarse

Jan 1, 1943

By J. H. Jackson, R. B. Fischer

VERY little is known about the properties of relatively pure refractory metals in the cast state since these metals are customarily made by powder-metallurgy methods. Recently, the development of the vacuum arc-melting furnace has made possible the study of large, sound ingots of cast molybdenum. The ductility of molybdenum, at room temperature, may vary considerably. Often the brittle state depreciates the utility of molybdenum, even for the material prepared by powder-metallurgy techniques. At the outset of this program, it was felt that if the causes of brittleness were to be determined it might be possible to reduce the difficulties met in the working of molybdenum. Also, the problem of producing strong, fusion weldrnents of molybdenum might be solved. The conditions required to produce ductile molybdenum by the powder-metallurgy technique are reasonably well known. A fibrous or elongated-grain structure has good ductility although this property is probably directional. The equiaxed structure obtained in fully recrystallized molybdenum has been considered to be brittle. The reasons for this behavior of molybdenum have not been established. The preparation of cast molybdenum ingots by the vacuum-arc method was described by Parke and Ham.' By this method, ingots weighing up to 250 Ib were produced." Parke and Ham1 found that molybdenum ingots containing more than approximately 0.0025 pct oxygen could not be hot forged. On the other hand, they found that fully deoxidized cast molybdenum, containing up to 0.06 pct carbon, could be hot forged. However, the as-cast ingots containing either carbon or oxygen were brittle at room temperature. Parke and Ham,1 Woodside,3 and Zapffe, Landgraf, and Worden4 noted the inter-granular precipitation of oxide or carbide in cast molybdenum. This study—part of an extensive program on mo-lybdenum—had the following objectives: (1) To investigate the causes for the brittleness of cast molybdenum at room temperature, (2) to investigate the means for improving the ductility of cast molybdenum at room temperature, and (3) to add to the knowledge of cast molybdenum and of cast metals in general.

Jan 1, 1951

By J. Larsen-Badse

The resistance to dry sliding abrasion us been measured for some hardened and tempered carbon steels. The wear resistance, defined as the reciprocal of the volume loss per unit sliding distance, is found to vary linearly with the hardness of the abraded surface. The data fit two lines, one, of high slope, for the pure metals and for the annealed steels and another, of smaller slope, for the hardened and tempered carbon steels. A relationship is developed showing the alwasion resistance to be proportional to the hardness of the material and to en, where n is the exponent of work hardening. The values of n and of the hardness FOR most materials a high resistance to abrasion is generally associated with a high value of indentation hardness. Brine11 even used the abrasion resistance as a measure of hardness in an attempt at expanding the hardness range covered by his indentation-hardness test.' When comparing different types of materials there is, however, only a very general relation between abrasion resistance and hardness. Sample brittleness seems to contribute to the deviation from a direct relationship. In general, increased brittle- are those relating to the heavily deformed abraded surface. However, for materials having n constant or varying m a regular manner over a wide range of strailts, the wear resistance will also be a linear function of the bulk hardness of the material. For tempered steels containing a dispersion of cementite in ferrite the increase in wear resistance due to the dispersion is found to be a linear function of the volume fraction of Fe3C and of the reciprocal of the mean free ferrite path. This indicates indirectly that the yielding of this material, when it is already heavily deformed, follows the Orowan criterion. ness leads to decreased abrasion resistance.' When comparing materials in the same group, e.g., the metals, the spread is less. Kruschov found that the abrasion resistance of pure metals and of annealed steels is directly proportional to the hardness of the metal. For hardened and tempered steels he obtained another linear relationship, one of smaller slope and intersecting the line for the pure metals at the location of the data for the annealed steels. He also found that the abrasion resistance of cold-worked metals is independent of the degree of cold working. This shows, as he concluded, that the process of abrasion work hardens the metal in the surface region to a very high degree.

Jan 1, 1967

By James F. McDivitt

The mineral industry of today is faced with a number of dilemmas, not the least of which grows out of the series of related facts-world mineral consumption is growing, and is expected to continue to grow; maintaining adequate capacity to meet needs will require very great capital investment over the next decades, investment which must be measured in billions of dollars; much of the new production must come from remote and relatively underdeveloped countries; many of the areas in which such development must take place are not areas in which private capital enters without some trepidation. There are real problems in financing new mineral development-problems which have occupied the thoughts of many in the industry. One group which is currently providing part of the answer, and perhaps pointing the way to further progress in the future, is the World Bank. Loans from the World Bank are arranged usually for countries which are attempting to develop their economies through expanded industrial production. More often than not they are for the development of electric power projects or transportation facilities. Although we consider the mineral industries to be basic factors in industrial development and very important factors in the early stages of development of a country, few of these loans are for mineral development-no more than a half dozen out of a total of well over 300 loans which have been granted to date. Yet the World Bank has played a far more important part in world mineral development than these figures would indicate. The few loans for mineral development which it has made are important, but of considerably greater importance are the secondary effects of many of the non-mineral development loans and some of the special services which the Bank also offers.

Jan 5, 1963

By Arthur B. Cummins, Henry Mulryan

DIATOMITE is a hydrous or opaline form of silica, commonly known as diatomaceous earth, diatomaceous silica or kieselguhr. The term "infusorial earth" has lost its original meaning and today is incorrect in view of the distinctions between diatoms and infusoria. Various locality and variety names are obsolete but some retain local significance. Moler and Celite are trade names that have become associated with diatomite products from certain deposits in Denmark and near Lompoc, California. COMPOSITION Diatomite is essentially silica with some combined water (2 to 10 pct). Frequently it contains organic matter (from traces up to over 30 pct) and varying amounts of inorganic impurities such as sand, cryptocrystalline silica, clay, volcanic ash, calcium carbonate, magnesia and soluble salts. In the natural or crude state, diatomite contains from 10 to 65 pct or more of free water. Table I gives analyses of several diatomites from deposits of different types. PROPERTIES Pure varieties, either massive or stratified, are friable and porous, of low apparent density, and somewhat chalklike in appearance. Varieties containing organic matter vary from sedimentary oozes to peatlike materials. Impure varieties may be more or less claylike, sandy, calcareous or cherty. Compacted types approach porcellanite and silicified shales. COLOR-white, cream, gray, tan, brown, greenish to nearly black. HARDNES-light-weight varieties appear 1 to 1.5 because of porosity, but microscopic particles are 4.5 to 6.5. SPECIFIC GRAVITY-1.9 to 2.35. APPARENT DENSITY---dry block form, 20 to 40 lb per cu ft; dry powder, 5 to 16 lb per cu ft. CRYSTAL SYSTEM-generally amorphous (isotropic by X-ray diffraction) but frequently showing faint cristobalite pattern.67.68,70 MELTING POINT-1400° to 1650°C. STREAK-white. LUSTER

Jan 1, 1949

By John W. Cahn

The spinodal has long been regarded as a limit beyond which a homogeneous phase could no longer be metastable. But only recently has it become apparent that a phase beyond the spinodal would decompose by simple diffusional clustering mechanism quite different from the nucleation and growth mechanisms encountered for metastable phases. The theory of spinodal decomposition, which is based on the diffusion equation modified by thermodynamic requirements , is phenomenological, and each parameter can be measured by independent thermodynamic or diffusion experiments. The details of the theory have been carefully verified in a number of simple systems. It appears that the spinodal mechanism is commonly encountered in clustering reactions in solids and glasses. HISTORICAL INTRODUCTION The understanding of the earliest stages of precipitation in alloys has been the subject of three prior Institute of Metals Lectures. In 1932 Paul ~erica' reviewed the puzzling evidence that hardening of duralumin is completed before precipitation of CuAlz takes place and suggested that hardening occurs when the copper atoms "assemble in random groups on lattice positions of the duralumin, not of the CuAlz lattice". He called these random groups knots. This modification of his dispersion hardening theory seemed to fit all the facts, but Merica worried that the required diffusion "is just the reverse of what we deem normal; although quite spontaneous, it proceeds uphill, if you please". The reality of Merica's knots was quickly confirmed by Guinier's' and preston's3 X-ray work and these knots are today known as G.P. zones in their honor. Theoretical justification for uphill diffusion was also quickly provided by Becker and Dehlinger~ who noted that the diffusion coefficient could be negative in certain regions of phase diagrams. The boundaries of such regions could be described by a 90-year-old thermodynamic concept first described by ~ibbs' in 1877 as a limit of metastability for fluid phases, which by 1890 had received the name spinodal (see Appendix A). Spinodal in fluids is as old as nucleation theory. Both appear for the first time in the same paper by Gibbs who called the spinodal the limit of metastability. For the first 50 years, nucleation theory was forgotten and the spinodal was extensively treated in every good thermodynamics textbook.81Q The idea was simple and logical and it was accepted as part of a rigorous thermodynamic development of metastable phases, and for a while it was extensively investigated theoretically.

Jan 1, 1969

By D. Silverman, A. R. Brown

EquipmENT and methods for locating the points of entry of salt water into oil wells are described. These techniques make it possible to delineate accurately the top and bottom boundaries of water zones whether bottom water or intermediate zones of production, Data are given on tests by this survey method on a number of producing wells, Complete results were obtained on wells shelving water percentages ranging from high values to as Little as 10 pct salt water. A number of the wells tested were plugged back and the results are reported in detail. While not all the work-overs were successful, evidence, including the results of reruns by this survey method, points to failure of the plugback operations. The data provided in the tests discussed show, contrary to general opinion, that a large percentage approaching 50 pct of the wells showed intermediate water instead of bottom water. Furthermore, approximately a third of the wells tested showed multiple zones of water production. The equipment comprises a long pipelike assembly carrying 10 pairs of electrodes spaced apart a distance of 4 ft. A surface-controlled solenoid-operated switch is provided to connect each of the individual pairs of electrodes in turn to a single-conductor steel-armored cable by means of which the conductivity of the fluid in the vicinity of each of the electrode pairs can be continuously recorded at the surface. Any number of electrode pairs and any spacing can be used. This assembly is lowered on tubing and placed in position opposite the section of the well to be studied. A conventional rod pump is used to produce the well for the survey. The pump inlet is placed below the lowest electrode pair. The well is conditioned by pumping Out the salt water normally standing in the well and introducing fresh water into the annulus at the surface. When the resistivity of the water standing in the well has been increased to a sufficiently high value, the inflowing fresh water is stopped and the drawdown operation of the survey is started. As the fluid head is lowered by pumping, fluids flow into the well and the entry Of salt water is indicated by the change in resistivity of the fresh water opposite the 'Ones Of water entry, The process can be repeated as Often as necessary with little effort and without moving any well equipment to be sure that the fluids produced from each zone are representative Of the true reservoir content. Introduction The oil industry has been concerned from its inception with the control of fluids entering its wells. In order to effect the greatest economy of operation and to get the greatest total production of petroleum liquids out of the ground, the flow of gas and water must be controlled and often extensive workovers are planned and carried Out for this purpose. This has become even more important in recent Years because of the need for the conservation of natural resources. Whereas producing operations concerned with the original completion of a well are assisted to a great extent by a wide variety of instruments developed and perfected for that purpose, workover operations on oil wells have been greatly hindered by a lack of suitable instrumentation. The industry has searched for many years for a satisfactory instrument and process that

Jan 1, 1948

By A. R. Brown, D. Silverman

EquipmENT and methods for locating the points of entry of salt water into oil wells are described. These techniques make it possible to delineate accurately the top and bottom boundaries of water zones whether bottom water or intermediate zones of production, Data are given on tests by this survey method on a number of producing wells, Complete results were obtained on wells shelving water percentages ranging from high values to as Little as 10 pct salt water. A number of the wells tested were plugged back and the results are reported in detail. While not all the work-overs were successful, evidence, including the results of reruns by this survey method, points to failure of the plugback operations. The data provided in the tests discussed show, contrary to general opinion, that a large percentage approaching 50 pct of the wells showed intermediate water instead of bottom water. Furthermore, approximately a third of the wells tested showed multiple zones of water production. The equipment comprises a long pipelike assembly carrying 10 pairs of electrodes spaced apart a distance of 4 ft. A surface-controlled solenoid-operated switch is provided to connect each of the individual pairs of electrodes in turn to a single-conductor steel-armored cable by means of which the conductivity of the fluid in the vicinity of each of the electrode pairs can be continuously recorded at the surface. Any number of electrode pairs and any spacing can be used. This assembly is lowered on tubing and placed in position opposite the section of the well to be studied. A conventional rod pump is used to produce the well for the survey. The pump inlet is placed below the lowest electrode pair. The well is conditioned by pumping Out the salt water normally standing in the well and introducing fresh water into the annulus at the surface. When the resistivity of the water standing in the well has been increased to a sufficiently high value, the inflowing fresh water is stopped and the drawdown operation of the survey is started. As the fluid head is lowered by pumping, fluids flow into the well and the entry Of salt water is indicated by the change in resistivity of the fresh water opposite the 'Ones Of water entry, The process can be repeated as Often as necessary with little effort and without moving any well equipment to be sure that the fluids produced from each zone are representative Of the true reservoir content. Introduction The oil industry has been concerned from its inception with the control of fluids entering its wells. In order to effect the greatest economy of operation and to get the greatest total production of petroleum liquids out of the ground, the flow of gas and water must be controlled and often extensive workovers are planned and carried Out for this purpose. This has become even more important in recent Years because of the need for the conservation of natural resources. Whereas producing operations concerned with the original completion of a well are assisted to a great extent by a wide variety of instruments developed and perfected for that purpose, workover operations on oil wells have been greatly hindered by a lack of suitable instrumentation. The industry has searched for many years for a satisfactory instrument and process that

Jan 1, 1948

By John V. W. Reynders

Our entry into the World War suddenly brought home to us in a startling way the vital importance of manganese. Since the war, much has been written and said upon the subject of manganese and a great deal of time and money have been spent in attempts to find an adequate substitute for this metal in the manufacture of steel; none has been found. It is true that ways are known by which it is possible to make small amounts of good steel without manganese, but taking into consideration the diminishing quality of iron ores and fuels as well as the increasing exaction of specifications for finished products, it may safely be assumed that, high-grade manganese ore will be more and more a necessity in the production of steel as time goes on. Taking world resources as a whole it may be well to point out that the problem of obtaining needed supplies of manganese from a strictly commercial viewpoint is now less serious than it was before the war. Formerly it was feared that world resources of high-grade manganese ore might be exhausted in a relatively short time, but, largely as a result of the stress laid upon the importance of manganese during the war, the world's available supply of high-grade manganese ore has been greatly augmented by new discoveries and fuller development of previously known deposits. Sources of Production Russia alone, of countries producing the major part of the world's stee1, has within its geographical boundaries sufficient manganese to supply its needs. The domestic production of England is inadequate and English requirements for high-grade manganese are supplied principally from India. France also draws largely upon India, as it depends upon foreign sources of supply except with respect to a small tonnage of silico-manga-nese and silico-spiegel produced in the Hautes-Pyrénées. Germany and the United States likewise depend upon foreign sources of high-grade ore, though each possesses comparatively large reserves of ferruginous manganese ore and manganiferous iron ore. At present the world demand for high-grade manganese ore is met with ease by the production of Russia, India, Gold Coast and Brazil.

Jan 1, 1927

By B. F. Oliver, C. W. Haworth

Pure tin and Sn-0.5pct Pb ingots have been frozen unidirectionally from the base. For quiescent melts that were initially undercooled, a transition from lower eqlciaxed structure to an upper columnar structure is found in the alloy ingots. Columnar to equi-axed back to columnar transitions are observed in superheated alloy ingots, but no such equiaxed band is observed impure tin. The reproducible equiaxed band is associated with a thermal undercooling followed by a recalescence. This undercooling is <5"C, whereas the critical (maximum obtainable) under-cooling for both the pure tin and the alloys used is -20°C. A similar undercooling is observed at the same position in the pure tin ingots, although in this case no clear transition in structure can be seen. The structure of the pure tin ingots is either entirely columnar or mixed columnar-equiaxed. A consideration of the detailed thermal history of the ingots indicates that the ingot macrostructures are determined by the occurrence of a local therlnal undercooling in conjunction with nuclei multiplication and transport mechanisrris. GENERALLY it is found that a pure metal ingot solidifies so as to produce an entirely columnar structure. Frequently an alloy ingot is found to have a columnar outer zone and an equiaxed central portion. Early systematic work to examine the factors controlling the formation of the equiaxed structure was reported by Northcott&apos; who showed that, for copper alloys frozen unidirectionally with a given ingot practice, the alloying element influenced the length of columnar crystals and the extent of the equiaxed structure. Northcott showed that alloys with a wider freezing range more readily produced the equiaxed structure. The nucleation process can be important in producing equiaxed structures; frequently an alloy which readily solidifies with an entirely columnar structure will produce an entirely equiaxed structure when a nucleating agent is added to the melt.&apos; The formation of the equiaxed structure was attributed by Winegard and chalmers3 to the presence of constitutional supercooling; that is, a region of liquid in front of the growing solid could have a temperature below its equilibrium liquidus temperature. Thus, with a small enough temperature gradient in the liquid, it was suggested that the presence of constitutional supercooling may be sufficient to bring about the nuclea-tion necessary for the formation of an equiaxed structure. Although this explanation is plausible, and may be relevant in many ingots, Walker has described an experiment&apos; for which constitutional supercooling seems to be an unlikely cause of nucleation. A Ni-20 pct Cu alloy, repeatedly undercooled more than 50"C, was crystallized and found to show the typical colum-nar-equiaxed structure. The separation between the liquidus and the solidus for the alloy is 40°C. Thus, in this experiment the nucleation required for the formation of the equiaxed structure must have come about in some other way than by the nucleation catalysis constitutional supercooling hypothesis. Chalmers has suggested more recently5 that nuclei (in a typical ingot) are present immediately after pouring and are prevented from redissolving by the constitutional supercooling effect. More recently Uhlman, Seward, Jackson, and ~unt&apos; have shown direct evidence using ice and organic materials that freeze dendritically that the "remelt mechanism" may be an extremely effective crystal multiplication process during the freezing of ingots under conditions involving dendritic growth. JSlia" experimentally demonstrated the detachment of dendrite arms. chernov14 has analyzed the dendrite arm detachment process as a coarsening phenomena driven by the minimization of interphase area. Katta-mis and ~lemings" working with undercooled steel melts give evidence supporting this mechanism. Mechanisms of dendrite arm detachment such as those assisted by convection are believed to be the origin of the macrostructures obtained in this study. This study makes no attempt to distinguish the relative contributions of these mechanisms. The object of the present work was to obtain accurate temperature measurements during the solidification of an ingot and to correlate these measurements with the formation of equiaxed grains in the resulting ingot structures. Similar previous work is very limited. The measurements carried out by Northcott are neither sufficiently extensive nor sufficiently accurate for any interpretation. Plaskett and winegard7 carried out experiments on A1-Mg alloys in which they observed values of the temperature gradient, G, in the liquid and rate of freezing, R (for a given alloy solute content Co), at the transition from a columnar to an equiaxed structure. They reported that equiaxed crystals were produced at values of G/G approximately proportional to the solidus composition. Similar experiments using Pb-Sn alloys carried out by £111011" showed a linear relation between G/R and the solidus composition. However, the thermocouples were in the mold wall rather than in the melt and, in one case, ingot surfaces were examined. There is ambiguity in the meaning of the values of G and R measured in all these experiments. APPARATUS AND EXPERIMENTAL PROCEDURE Alloys were prepared by induction melting 99.999 pct Sn and 99.999 pct Pb to form a Sn-0.5 wt pct Pb alloy in air in a graphite crucible and casting into a cylindrical graphite mold 6 in. long, 1 in. in diarn , and with a & in. wall thickness. This mold was mounted on a copper base through which cooling water could be

Jan 1, 1968

By T. Sterry Hunt

Jan 1, 1891