Search Documents

By Lo-Ching Chang, Kenneth M. Goldman

INTRODUCTION THE kinetics and mechanism of transfer of a constituent across a slag-metal interface are fundamentally important because many metallurgical processes involve the existence of a slag phase and a metal phase. Industrial processes seldom proceed to equilibrium, and information of the rates and modes of reactions are therefore often of greater practical importance than equilibrium data. A study of the kinetics of sulphur transfer across a slag-metal interface under reducing conditions will contribute a great deal toward a better understanding of desulphurization in the blast furnace process. The general principles existing in the transfer of a constituent, such as sulphur, across a slag-metal interface can be extended to similar transfer phenomena in other metallurgical processes. The present paper will demonstrate how such studies will lead to fruitful results from both the practical and theoretical standpoints. EXPERIMENTAL METHOD The apparatus used was simple. A graphite crucible 1 5/8-in. id, a wall 1/8-in. thick, and a depth of 4 in., was packed in an outer fused silica tube with powdered magnesia. The crucible assembly was rotated at a speed of 235 rpm inside an induction coil. A charge of 250 g of Armco ingot iron was introduced into the graphite crucible and melted by induction heating. The melt was held at a desired temperature [ ] for 3-5 min., after which 7.5 g of granular ferrous sulphide was added and the bath was held for another 3-5 min. A metal sample was then taken by means of a fused silica tube and a rubber suction bulb. Immediately after the metal sample was taken, 30 g of a prefused and crushed slag were introduced. The slag reached the temperature of the furnace in 1 to 1 1/ 2 min. Slag

Jan 1, 1948

By Hsun Hu

Direct observations were made on the recrystalli-zntion of a cold-rolled (110) [001] crystal of 3 pct Si-Fe by annealing thin sections of the specimen inside the electron microscope during examination. Subgrain formation, presumably by polygonization, occurs rapidly, followed by a slow increase in the subgrain size before recrystallization can be detected. No migration of the subgrain boundaries was observed, and the formation of recrystallization nuclei by coalescence of subgrains is suggested. Re-c~ystallization characteristics of various texture components were individually examined. AS reported in a previous paper: orientations of the various deformation texture components in a 70 pct cold-rolled (110) [0011 crystal of 3 pct Si-Fe were completely confirmed by transmission electron diffraction patterns taken at various areas of the specimen. These orientations can be summarized as follows: Over most areas of the deformed crystal (111) planes are parallel to the surface. These areas correspond to either $- the two main defor: mation textures, the (111) [112] or the (111) [112].2-5 Within a few areas, (100) planes parallel to the surface are frequently found. These areas represent the minor deformation texture component, the (100) [Oll] type, which is derived from rotated Neumann bands.2'4'5 Only in very rare instances are (110) planes found parallel to the surface. This orientation corresponds to the very weak texture component of the (110) [001] type. In a pole figure, this (110) [0011 orientation is located within the orientation spread between the two main (111) [1121 type textures. Usually the electron diffraction patterns taken at various areas of the specimen are very simple ones, i.e., for any one area the pattern consists only of sharply defined spots of a single orientation. In some areas, however, more or less continuous rings of weaker intensities are superimposed on a simple pattern, indicating the presence of a wide range of additional orientations. In order to understand in detail the recrystallization of this cold-worked crystal, the recrywtallization characteristics of each of the various deformation texture components must be examined. This can best be done by using a high-temperature stage and transmission electron microscopy techniques, whereby small areas corresponding to the various texture components can be selected individually for examination. The present paper presents results obtained by this method. MATERIAL AND METHOD Specimens were prepared from a previously studied1 single crystal of a commercial grade 3 pct Si-Fe alloy with an initial orientation (110) [00l], cold-rolled 70 pct from 0.014 in. to 0.004 in. in thickness. Thin foils were prepared by electrolytic polishing as described in the earlier paper.' Specimens of this thin foil were then mounted in a high temperature stage similar to the one designed by Whelan.6 A direct current was used as the heating source. The temperature of the heating grid was calibrated by means of a Pt vs Pt-10 pct Rh thermocouple in a vacuum chamber (0.01 to 0.02µHg). Maximum variation within the temperature range of 250o to 000°C was about ± 25°C. After the desired areas were selected for examination, the specimen was heated to a low temperature for some time while the selected area was constantly watched. When no further change in structure and orientation could be observed, a higher temperature was applied. Photomicrographs and diffraction patterns were taken from time to time during examination, with the heater temporarily turned off* while the photographs were

Jan 1, 1962

By E. Miller, J. M. Eldridge, K. L. Komarek

The thermodynamic properties of- liquid Mg-Pb allojs have been determined by an isopiestic method from 18 to 42 at. pct Pb and by a thevmodynumic analysis of the phase diagram frofiz 0 to 100 at. pct Pb. In the overlapping composition range the magneszupn activity values derived by the two methods are in excellent agreement, thus mutually supporting the correctness of the Mg-Pb phase diagram previously determined by the authors and of the acticitzes deriz~ed isopiestically. SEVERAL studies have been made of the thermody-namic properties of liquid Mg-Pb alloys. Wagner and Engelhardt,1 Lantratov,2 Knappwost,3 Sryvalin et al.* and Wilson5 used the electromotive-force method, Scheil and Wolf8 and Schmahl and Sieben" applied the transpiration technique, and the present authors8 utilized the phase diagram to determine the activity of magnesium in the Mg-Pb system. The results of these studies are not in very good agreement and could not be incorporated into a general systematic analysis of the thermodynamic properties of the homologous series of the Mg-Group IV B systems Mg-Pb,8 Mg-Sn,° Mg-Ge,10and Mg-Si.11 The thermodynamic properties of the Mg-Pb system were therefore re investigated by an isopiestic technique which has been developed for similar studies in the Mg-SnB and Mg-Ge10 systems- Lead specimens, contained in iron or graphite crucibles, were heated in a temperature gradient in an evacuated and sealed titanium reaction tube and equilibrated with magnesium vapor of known vapor pressure to form alloys of compositions which depended on their temperatures, the temperature of the magnesium vapor source, and the thermodynamic properties of the system. EXPERIMENTAL PROCEDURE Magnesium (Dominion Magnesium Ltd., Toronto, Canada) of 99.99+ pct purity and lead (American Smelting and Refining Co.) of 99.999 pct purity were used. In the early experiments, Runs 2 and 3, the alloys were contained in uncovered high-purity iron crucibles. Alloys formed in the uncovered iron crucibles had to be chemically analyzed owing to the slight volatility of lead under the imposed experimental equilibration conditions. The compositions of these alloys were determined by a gravimetric analysis of lead as lead chromate. To avoid this problem, the remaining runs were made in covered graphite crucibles machined from high-density (1.92 g per cu cm) graphite rods (Basic Carbon Corp., Sanborn, N.Y.) which had a maximum ash content of less than 0.04 pct. The non- i reactivity of graphite with lead and magnesium has been previously established,' and the experimental procedure has been described in full detail.' In the runs using covered graphite crucibles it was found that the weight increases of the crucibles and their contents after equilibration equaled the magnesium contents of the alloys within the accuracy of the chemical analysis (i0.3 at. pct Pb). Clearly, the small lid openings of the graphite crucibles prevented significant lead losses during a run, and the weight increase was therefore taken as the magnesium content of the alloys. EXPERIMENTAL RESULTS At thermodynamic equilibrium the magnesium partial pressure of the specimens equaled that of the reservoir. Since the magnesium reservoir was always maintained at the temperature minimum of the system, the activity of magnesium of any specimen was given by the ratio of the magnesium reservoir pressure to the vapor pressure of pure magnesium at the specimen temperature. The standard state was chosen as liquid magnesium and the vapor pressure of liquid magnesium

Jan 1, 1968

By W. B. Plank, A. C. Callen

WAR and normalcy do not walk hand in hand, whether it be in industry, the educational field, or in the daily lives of individuals. Schools and departments offering curricula in mineral engineering have been seriously disrupted, beginning with 1942 and reaching a low during 1944. Selective Service regulations and voluntary enlistments have effectually stopped the flow of college-trained men into the mineral industry, and the flow into the colleges is little more than a dribble. The year just closed has been a most serious one for our institutions. Until March many of our faculties had been kept reasonably intact because of the large training programs of the Army and Navy. Although the number of

Jan 1, 1945

By J. J. Gilman

The data presented indicate that the critical shear stress and strain-hardening Thedatapresentedrate of a zinc monocrystal depend on the orientation of its slip direction with respect to its external boundaries. The tendency of a crystal to form deformation bands also depends on its shape. THE plastic behavior of pairs of zinc monocrystals in which both members of the respective pairs had the same orientation with respect to the longitudinal axis, but each had different orientations with respect to their rectangular external shapes, were compared in this investigation. The purpose of the investigation was to see what influence the shape or surface of a zinc crystal has on its mechanical properties. In a previous investigation of triangular zinc monocrystals,1 anomalous axial twisting was observed which seemed to be related to the triangular shape of the crystals. Wolff,' in 400°C tensile tests of rectangular rock-salt crystals bounded by cubic cleavage planes, found that, of the four equivalent slip systems, the two with the "shorter" slip directions yielded and produced slip lines at lower stresses than the other two. This observation and the work of Dommerich³ as formulated by Smekal4 as a "new slip condition" for rock-salt: "among two or more slip systems permitted by the shear stress law, with reference to the formation of visible slip lines by large individual glides, that slip system is preferred which has the shortest effective slip direction." More recently, Wu and Smoluchowski5 reported essentially the same effect for ribbon-like (20x2x0.2 mm) aluminum crystals at room temperature. Experimental Chemically pure zinc (99.999 pct Zn), purchased from the New Jersey Zinc Co., was the raw material. Glass envelopes, containing graphite molds and zinc, were evacuated while hot enough to outgas the graphite but not melt the zinc. At a vacuum of about 0.2 micron the envelopes were sealed off and then lowered through a furnace at 1 in. per hr so as to melt and resolidify the zinc and produce mono-crystals. One-half of one of the molds is shown in Fig. la. Each mold consisted of four pieces from a cylindrical graphite rod that was split longitudinally and transversely at its midpoints. Rectangular milled grooves 0.050 in. deep and % in. wide formed the mold cavity when the split halves were assembled with twisted wires. Fig. lb shows the specimen shape obtained when the top and bottom mold-halves were rotated 90" with respect to each other. Good fits prevented leakage and excess zinc was necessary to provide enough liquid head to fill the mold completely. In removing soft crystals from the molds it was impossible to avoid small amounts of bending. However, manipulations were carried out whenever possible with the crystals protected by grooved brass blocks. All specimens were annealed prior to testing. From the top and bottom sections of each crystal, X-ray specimens and tensile specimens 7 to 8 cm long were sawed. The tensile specimens were annealed inside evacuated tubes for 1 hr at 375°C. Next the crystals were cleaned and polished by 2-min dips in a solution of 22 pct chromic acid, 74 pct water, 2.5 pct sulphuric acid, and 1.5 pct glacial acetic acid.' Cleaning was followed by a 10-sec dip in a 10 pct caustic solution, then washed in water and alcohol, and dried. This treatment results in a bright surface covered by an invisible oxide film. The testing grips were a slotted type with set screws and were supported in a V-block during the mounting operations in order to avoid bending the crystals. A schematic diagram of the recording tensile-testing machine is shown in Fig. 2. The machine has been described elsewhere.' The head speed was 0.3 mm per sec for all tests. The crystal orientations were determined by the Greninger X-ray back-reflection method with an estimated accuracy of 1. Description of Crystal Geometry A schematic picture of a rectangular zinc mono-crystal is shown in Fig. 3. ABD designates the front edge of a basal plane (0001) of the crystal, the only active slip plane for zinc at room temperature. Of the three possible (2110) slip directions, the active one is indicated by an arrow. Cartesian coordinates are taken parallel to the specimen edges. The normal, n, to the basal plane (n is parallel to the hexagonal axis) has the direction cosines a, ß and ?. X0 = 90 — y is the angle between the longitudinal axis and

Jan 1, 1954

By P. Ramachandraraa, T. R. Anantharaman

THE technique developed by Duwez, Willens and Kle-ment' for rapid solidification of molten alloys in small quantities by ejecting them on to a highly conducting substrate with the aid of a shock wave has come to be known as "liquid quenching" or "splat cooling" in literature and has already been applied to alloys of many binary systems.' The very high cooling rates of the order of l060 to 1080 per sec obtained in this technique and the consequent drastic undercooling of the melt have led to such striking results as formation of new amorphous and crystalline metastable phases and extension of solid-solubility limits in many alloy systems. The cooling rates in these experiments can, however, be neither accurately measured nor effectively controlled and hence the occurrence of either more than one metastable phase or appreciable differences in constitution in splat-cooled alloys of the same composition cannot be ruled out.3 In fact, workers in two laboratories have reported formation of two different cubic metastable phases in liquid-quenched Au-Si alloys containing 17 to 20 at. pct si.4,5 The present note deals with some new and interesting results obtained in a Ag-21 at. pct Ge alloy and a Au-27 at. pct Ge alloy subjected to the liquid-quenching treatment at different cooling rates. Two alloys of nearly the same composition had earlier been rapidly solidified by the standard "gun technique" in the same laboratory and shown to solidify in nonequilibrium structures, viz., an hcp phase (a = 2.987Å;c =4.718Å) in the Ag-Ge system6,7 and both hcp (a = 2.885Å; c = 4.754Å) and tetragonal (a = 11.627A; c = 22.491Å) phases in the Au-Ge system.3 Apart from different substrates (copper and stainless steel), different melt temperatures (50º to 500°C above the liquidus), and different capillary sizes (0.4 to 1.5 mm diam) in the "gun technique", slower cooling rates of the order of l050C per sec were also obtained in the present work by replacing the substrate by water at room temperature in a modification of the technique due to Olsen and Hultgren.8 No attempt was made to measure the cooling rate in any experiment. The products varied from fine powder (>40 pct by wt—200 mesh) obtained by quenching in water to thin flakes and foils (11.0 sq mm to 4.0 sq cm) produced by splat cooling. They were subjected to the Debye-Scherrer method of X-ray examination in each case. In case of the Ag-Ge alloy, in addition to the expected metastable hcp phase,6 a coexistent tetragonal phase (a = 5.093,Å; c = 7.009Å) was detected in some experiments. Eight weak X-ray reflections from this phase could be identified, two of them being the same as reported earlier.7 With increase in the cooling rate, the dominant hcp phase seems to be first accompanied by traces of silver or germanium and then either homogeneous or mixed with traces of this new tetragonal phase. The splat-cooled Au-Ge alloy showed generally the expected hcp and tetragonal phases,3 but sometimes traces of germanium were also present. Further, two new tetragonal phases with the following lattice param ters could be clearly identified in samples quenched

Jan 1, 1970

By G. O. Hiers

THE object of the experiments reported in this paper is to determine the eutectic composition of copper and tin and to determine the location of the part of the liquidus line immediately above the eutectic composition in copper. Three methods were used in the investigation: (1) the method of dissolving copper in a bath of molten tin at constant temperature, with the idea that when the bath was saturated with copper its copper content, by analysis, together with the temperature at which the saturation took place would locate a point on the liquidus line (2) the method of the differential cooling curves, and (3) the method of microscopic examination. This paper is principally concerned with the results of the last two methods mentioned. The results of the first method, that of dissolving copper in molten tin, did not agree with the .results of Miller,1 by the same method, nor with the results of other investigators by other methods, nor yet with the results of the cooling-¬curve experiments and microscopic examination reported here.

Jan 1, 1929

By B. K. Miller, R. S. Bradley

THE principal producing areas of fire clay in Missouri are: (I) the east central district, which includes Audrain, Callaway, Montgomery, Warren, and Boone Counties [ ] (Fig. I); (2) the St. Louis district, which includes St. Louis and St. Louis County; (3) the north central Ozark district, which includes Franklin, Gasconade, Osage, Maries, Phelps, and Crawford Counties. [ ] Most of the semiplastict fire clay is found in Audrain, Callaway, Montgomery and St. Louis Counties, and in St. Louis. Flint fire clay is found in Callaway, Audrain, and Montgomery Counties and in most of the north central Ozark district. High-alumina [ ] diaspore clay is found only in the north central Ozark district, except a few deposits found in Montgomery County. This paper is concerned with the semiplastic fire clay that occurs in the east central Missouri district near Mexico, Audrain County, Missouri, which is mined by the open-pit method as practiced by the A. P. Green Fire Brick Co. About one-fourth of the semiplastic fire clay in that district is mined in shaft mines, and three-fourths in open pits.

Jan 1, 1941

By C. D. Cochran, F. H. Deily, M. M. White, Victor Horner

A laboratory study of the effects of physical and easily measured rheological properties upon dynamic filtration was carried out. The purpose was to determine the factors affecting dynamic filtration and thus learn how to control this important property. The recommended procedure for determining the amount of fluid loss prescribed by API Code RP 29 "Field Procedure for Testing Drilling Fluids,"' is very useful for mud conditioning purposes, but inadequate for comparing filtration properties of different muds under dynamic conditions. Where dynamic filtration control becomes important for purposes such as logging and coring, other means of evaluating filtration properties are needed. A special device and testing technique were developed to provide reliable data on filtration characteristics of different fluids under dynamic conditions. Liquid saturated rock samples were drilled with a microbit, and the amount of connate liquid displaced by the fluid being investigated was measured. The empirical testing procedure was considered reliable. A large number of laboratory-prepared and field-mixed dritling fluids with a wide range of physical properties were studied. These properties included: (I) shape of consistency curves, (2) apparent viscosity, (3) plastic viscosity, (4) yield value, (5) density, and (6) API filter loss. Test results indicate that very little, if any, trend could be established between changes in these fluid properties and dynamic filtration. INTRODUCTION During the process of drilling, excessive loss of liquid from the mud to the formation is undesirable for many reasons. Filtration can reduce production-zone permeability, cause sloughing of formations, affect electric log curves, and render the fluid data obtained from cores unreliable. Thus, it is very important that we gain a knowledge of the factors that control filtration. It is generally agreed that in any type of filtration (static, dynamic, or combinations thereof), the mechanics of filtering depend in great part upon the composition of the fluid. Moreover, it is also true that the physical and rheological properties are influenced by the composition of the fluid. Indirectly, then, it was hypothesized that a relationship existed between dynamic filtration and physical-rheological properties, two effects of a common cause—fluid composition. This paper discusses an attempt to relate filtration-while-drilling to physical and easily measured rheological properties. It is believed that the results of this study may prove useful to others in the industry who are working on the problem of understanding filtration. The industry accepted practice for determining fluid loss from drilling mud is described in API Code RP 29. The practice is to measure the amount of filtrate that passes during a given interval of time from a quiescent drilling fluid under applied pressure through a piece of filter paper. This is primarily a test of static filtration properties. Other investigators have studied filtration under dynamic conditions. Williams5 and Pro-kop5 studied radial filtration and filter-cake buildup by circulating fluid through a porous cylinder under conditions similar to actual mud flow. Nowak,4 Krueger,3,4 and Vogel3 studied the effect of filtration upon permeability by flowing mud past the face of rock Samples. In their tests, the bit action was simulated by mechanical scrapers that kept the filter cake from building up. Ferguson and Klotz2 studied three types of filtration: static, dynamic, and beneath-the-bit. They investigated each type separately, using a model well in which bottom-hole hydraulics and mechanics were closely approximated.

Jan 1, 1958

By H. O. Hofman

PAGE Part I. Decomposition OF Zinc Sulphate by Heating in Air, . 811 I. Introduction............ 811 II. Zinc Sulphate Used,..814 III. Fumes and Pyrometers,........ 816 IV. Heating Zinc Sulphate—Dehydration,...... 817 V. Heating Zine Sulphate—Decomposition...818 (a.) Beginning of Decomposition..818 (b.) Rapidity of Decomposition,..819 (c.) End of Decomposition..823 (d.) Retardations in Heating.-Curve,..825 (e.) Formation of Basic Salts,..826 Part II. Decomposition OF Zinc Sulphate by Heating with Carbon (Reducing Roast), .830 I. Introduction,........... 830 II. Experiments and Results ,.........832 III. Summay,........... 834 Part 111. Formation of Zinc Sulphate by Roasting,... 834 I. Introduction,........... 834 IT. Description of Blende,......... 836 III. Outline of Operations,.........838 IV. Details of Experiments.......... 839 1. Decrepitation,.......... 839 2. IgnitionPoint,....839 3. Sulphatizing-Roast of Joplin Blende..840 4. Sdphatizing-Roast of Warren Blemde ,..843 5. Sulphatizing-Roast with Addition of Pyrite...848 6. Summary of Sulphutizng-Roasts,....... 854 Part IV. Appendix : Formation of Zinc Ferrate...856 Part I. Decomposition of Zinc Sulphate by Heating in Air. I. Introduction. With the exception of lead sulphate. all common metallic

Jan 1, 1905

By Nicholas J. Grant, Oliver Preston

A series of dilute solid solutions of a1uminum and silicon in copper, in powder -form, were internally oxidized, compacted, and extruded, to produce Cu-A12O3 and Cu-SiO2 alloys with 0.1 to 12 vol pct of oxide. Room-temperature tensile tests, creep-rupture tests from 450oto 850°C. conductivity measurements, and recrys-tallzzation studies were made. Oxide particle size and interparticle spacings were determined in an effort to relate the structure to measured strength values by means of known dispersion strengthening theories. A new dispersion strengthening theory, based on the effect of the dispersed phase on the retention of strain energy from the deformation step, zs proposed for this type of alloy, THE study of dispersion strengthening is of partitular interest in high-temperature materials technology in view of the excellent creep-rupture Properties and thermal stability achieved with SAP.1-5 Considerable effort has been devoted to this study in recent years, and encouraging results have been obtained in a number of systems.6 In general, the most

Jan 1, 1962

By J. A. Hren, C. M. Wayman

RECENT investigators have noted anomalous behavior in the electrical resistivity of vanadium below room temperature. Rostoker and Yamamoto1 in studying the vanadium-oxygen system hypothesized that the body-centered-tetragonal phase existing from 15 to 34 at. pet O at approximately 800°K was really a low-temperature allotrope of vanadium that was stabilized by oxygen. In measuring the electrical resistance of cold-swaged vanadium rod over a range of temperatures, a small discontinuity was observed at approximately 240°K, supporting their notion of allotropy. However, the magnitude of the observed discontinuity was extremely small. Loomis and Carlson2 in studying the ductile-brittle transition in vanadium also made resistance measurements and reported a discontinuity near 200°K. More recently, White and Woods3 showed that the electrical resistivity from room temperature to approximately 100 °K was not linear and at variance with the Bloch-Griineisen law. Instead of finding a discontinuity, they observed a deviation from linearity below 200°K. In discussing their results they pointed

Jan 1, 1961

By Charles W. DeWitt

The ore treated at the reduction plant (called Yangdei) of the Chiksan Mining Co., Korea, is brought from four of the company mines, and from the small tribute mines. The largest shipments come from Sajunkohl mine, situated about a mile and a half from the mill (Fig. 1). The ore is quartz of medium hardness. The average assay value in gold is $6.95 per ton. At the mine the ore is put into bins, and is then trammed over an 8 per cent, grade to the tipple bins above the mill, where the ore is drawn through the mill holes as desired. The capacity of the tipple bins is about 3,500 tons. Ore from Moonsukohl, Chung Tarrie, Yang Chun, and the tribute mines is brought in by bulls and bull wagons. The bulls carry from 350 to 800 lb.; the average wagon load is about 1,200 1b. (Fig. 2). One shovelful of ore out of every ten is taken as a sample. Considerable ore is brought in from the outside mines, and this method of sampling is

Jan 1, 1916

By F. R. Hensel

THE present study was rude to determine the laws governing the formation of the primary? crystal structure during solidification. Most of the experiments were carried out on chill castings, but from the results it will be possible to draw certain conclusions as far as sand cast-ings are concerned. It is necessary to discuss first a number of theories, which are generally adopted for explaining the structure of an ingot. Usually, the structure FIG. 1.-VARIOUS ZONES IN A CHILL INGOT. off an ingot consists of the following three zones (Fig. 1): (1) a chill layer of small at. random oriented crystals; (2) a layer of columnar crystals; (3) a zone of equiaxed crystals. The tensile properties of the chill layer and the equiaxed range are usually much better than in the columnar range, particularly the planes that are formed by the columnar crystals growing from two sides at right angles leave low tensile properties. This is one of the reasons why colum-nar crystals in ingot structures are undesirable.

Jan 1, 1937

By W. H. Emerson

In the summer of 1894, a specimen of corundum from Acworth, Ga., which mas reputed to be of markedly inferior quality for the manufacture of corundum-wheels, was received by the Geological Survey of Georgia, with the request that it be analyzed, in order to ascertain whether this inferiority was associated with any peculiarity of composition. In its appearance there was nothing uncommon, though it seemed to be rather easily scratched with a knife, while, at the same time, it scratched agate easily. An analysis gave the following results: Alumina, 94.58; silica, 1.77; magnetic oxide of iron, 0.69; calcium oxide, 0.44; and water, 2.51 per cent. There is nothing unusual in this composition, except the amount of water, which is usually, in southern corundum at least, from 0.3 to about 1 per cent. Concerning this corundum, the Mineral Resources of the United States, 1893, pp. 676 and 677, Bays: "It is supposed that this variety of corundum contains a little water, as it is

Jan 1, 1900

By J. W. Axelson

CRUSHING has always been a major operation in the chemical and metallurgical industries, yet little is known about the theory of crushing, and today, the design of crushers is still based almost entirely on empirical knowledge and accumulated practical experience. In view of the increasing national need for the economic working of poorer grades of ores, the lack of a fundamental under- standing of this unit operation hardly presents a satisfactory situation. Basic investigations of crushing have been concerned mainly with three phases of the problem, 1-the mechanism of the fracture process itself, 2- the particle size distribution of the crushed product, and 3-the relationship between the energy input and the amount of new surface produced. Probably adequate information on these phases will be required for a comprehensive understanding of the process of crushing. A bibliography covering these phases will be given as well as a review of the work done in recent years at the University of Minnesota on the relationship between the energy input for crushing and the amount of new surface produced.

Jan 12, 1951

By Frank C. Roe

Two cogent and ubiquitous facts have supported a constant search by the ore processing industry for better wear resistant materials in equipment. First, designs and types of equipment change or improve continually to meet the economic and physical demands of different and/or leaner ores. Second, practically all equipment is subject to impact and abrasion conditions that probably are more severe and extensive than in any other industry. Development and testing by operators and equipment manufacturers alike, has produced an extensive variety of longer lasting metal alloys, rubber, plastics, ceramics and other materials to improve equipment performance under different specific conditions. The need for diversified materials becomes obvious upon the simple realization that no two beneficiation operations are identical. Among the variables in the handling of ore are: 1. Size and weight of ore particles. 2. Hardness and sharpness of ore particles. 3. Concentration of ore particles in liquid or gas suspension. 4. Velocity and direction of particle impact toward equipment surface. 5. Coefficient of friction between ore particles and equipment surface. 6. Temperature of operation. 7. Chemical environment of operation.

Jan 12, 1967

Jan 1, 1925

By Sam F. Carter

FOR some time melters and metallurgists have recognized the fact that steels may be made to identical compositions as ordinarily analyzed, but with considerable variations in physical properties. Good melting practice signifies a combination of furnace operations that will produce steel with consistently good physical properties after proper consideration of cost, production efficiency, and chemical control. In acid practice, these operations may be classified fundamentally as: (I) the oxidizing boil, (2) recarburization and deoxidation, (3) slag adjustment, and (4) final deoxidation. These operations affect the properties of the steel through variations in the minute quantities of several microscopic, submicroscopic, and dissolved constituents, which are out of reach of ordinary analyses but are very influential upon the crystallographic slippage and the molecular cohesion of the structure. One of these constituents is the FeO left in solution in the steel. Herty has shown that steels high in dissolved FeO have decreased ductility and impact and increased hardness and electrical resistance. There is also much evidence that FeO in solution affects carbon solubility and diffusion, and consequently abnormality and carburizing behavior.

Jan 1, 1947

By N. P. Peterson

THE Castle Dome copper deposit is of the porphyry type and occurs in a body of quartz monzonite intruded into the pre-Cambrian formations and possibly into the lower part of Paleozoic limestones. The hypogene sulphide minerals include pyrite, chalcopyrite, and a little molybdenite, sphalerite, and galena. Pyrite and chalcopyrite are disseminated or occur in small closely spaced veins. The hypogene mineralization shows distinct zoning in the distribution of pyrite and chalcopyrite, so that the mineralized area can be subdivided into pyrite and chalcopyrite zones. Supergene enrichment, though not extensive, played an important part in the formation of the ore body, the chalcopyrite zone being the protore. Several thin, gently dipping, diabase sills occur in the mineralized area, and the copper content of the rock in and near these sills is substantially higher than average. The formation of the ore body was caused by the combined effects of three forces: I. Zoning of the hypogene mineralization, 2. Richer copper metallization associated with the diabase sills, and 3. Supergene enrichment.

Jan 1, 1947