Search Documents

By A Thornton, D Engelhardt, J Woodg

Grinding is a critical part of nearly all mineral processing operations. It is the largest consumer of energy on the mine site (and thus indirectly a producer of greenhouse gas through the generation of electrical energy at the power station). Since comminution is one of the main consumers of electrical energy worldwide, efficient control of grinding mills is of paramount importance. Mill Auto-Pilot is a control system developed for SAG mills to stabilise load and power and improve the efficiency of control and increase throughput. A dynamic, mechanistic model of the grinding circuit is used to determine circuit parameters which can not normally be measured using conventional instrumentation. The circuit model is built from models of the unit operations (such as conveyors, SAG mills, cyclones, sumps, etc), and so captures the dynamic complexities and interactions of real circuit operation. CSA Mines at Cobar NSW accepted an offer to be the reference site for Mill Auto-Pilot and the system was installed in March 2004. In this application the model is used to predict mill load mass, mill solids residence time and cyclone underflow density. These parameters are used to control mill load, power and mill discharge density. The outcomes of the introduction of Mill Auto-Pilot at the CSA Mine are discussed.

Jan 1, 2004

By Seeley D, Buckley N, Goodall J

Improving the performance and reducing the costs associated with export logistics chains is critical to the competitiveness of export coal mines. The fundamental practices associated with the use of export logistics chains made up of mine, trucking, rail and port operations are being challenged by the advent of third party operators on rail systems and the use of the Internet.Whilst individual mines can improve their processes to drive down their mining costs, they face major challenges in their endeavour to improve the performance of export logistics chains and reduce the significant logistics costs of moving coal from the mine to export ships, via the shared infrastructure of rail systems and ports. There is an increasing realisation that global competition is not only between mines but between coal export regions that are defined by their rail system and ports infrastructure.

Jan 1, 1998

The treatment of slimes has of late years been the chief difficulty in connection with cyanide work, in which much time and money has been spent in endeavouring to find a practical solution of this problem.The processes at present in use are:-1. Filter pressing, as practised in Western Australia.2. Decantation, as practised in South Africa.Filter pressing after apitation affords a ready and efficient means of separating the gold bearing solution from the slimes and admits a perfect washing thus ensuring a high extraction but the very high working costs forbids its application except on high grade material, the chief items being the necessary large amount of labour, compressed air, and general upkeep, none of which can be materially reduced. The decantation method has the ad vantage of low working cost but on the other hand the low extraction obtained, due to imperfect washing, the length of time occupied in' the treatment, and the enormous bulk of solutions to be handled, are serious disadvantages.In either process it is absolutely necessary to obtain a perfectly clean solution before starting the gold precipitation by zinc, which is a source of much trouble. Also the high first cost of installing either plant is such that they can only be adopted on mines with very large working capital.

Jan 1, 1903

By D Williams

Recent advances in global positioning systems (GPS), machine guidance technology and telemetry allow an unprecedented level of control of surface mining operations. GPS technology can now locate the bucket of a shovel or the blade of a dozer within 50 mm. Some of the outcomes possible are: precise selective mining û even when the ore is visually indistinguishable from waste; tracking grade and tonnage of every ore parcel through the mine; real time productivity monitoring; detailed post accident safety analysis; and tracking the movements of every piece of equipment. This paper will consider the contribution that GPS based machine control systems can make to ensuring that surface mining projects deliver the outcomes promised in the feasibility studies. Case studies of installations are presented.

Jan 1, 2003

By Bebb G

This paper describes the use of SURPAC, a survey/mine planning software package as used at Central Norseman Gold. It details the basic operating principles of the package, the applications in which it is employed, and its time and cost benefits and efficiencies as they apply to the above operations, both surface and underground.

Jan 1, 1985

By Ellery B. I

Field investigations recently undertaken by Utah Development Company (U.D.C.) have been developed to allow the assessment of ground conditions relevant to the use of large bucket wheel excavators for pre-stripping overburden. "Bucketwheel diggability" predictions were made on the basis of a wedge test which was perform- -ed in the field on nominal 150 mm diameter drill core samples. Specific separation force (calculated from the wedge test results) for different rock horizons were theoretically related to the excavation rates of various sized bucketwheels, i.e., "bucketwheel diggability". The specific separation force was shown to vary with lithology, structure, weathering and moisture changes. By correlating these features between boreholes, an overall assessment of bucketwheel diggability was then made. The approach adopted to assess bucket- wheel diggability incorporated various levels of investigation. Initially, a reconnaissance stage provided information from widely spaced 150 mm cored holes to compare and contrast areas with differing bucketwheel digging char- -acteristics. The following stages progressive -ly added to this information, until finally, between hole correlations, allowed calculations to be made of volumes of materials of similar

Jan 1, 1981

By Fulton B, Stewart R, Leach T

Gold mineralisation at Porgera is inferred to have been derived from a deep differentiated magmatic source which is capped by a series of (now tilted) inward dipping sills and stocks, which comprise the Porgera Intrusive Complex. An arc normal transfer structure provides a conduit, at the intersection with an arc parallel structure, into which basic magma derived from the deep melting of mantle material has been emplaced. Two phases of mineralisation display an association with late stage feldspar porphyry intrusives. Stage I carbonate-base metal-style gold mineralisation occurs as early quartz-sericite, then massive sulphide and late zoned Mn-Fe-Mg-Ca carbonate vein/breccias. Magmatic fluids derived from the deep magma source, are interpreted to have migrated along the margin of a feeder stock to the sills, and south to Waruwari. Stage II epithermal Au-Ag quartz-style gold mineralisation occurs as early fluidised breccias and carbonate veining, followed by zoned quartz-roscoelite-carbonate-gold vein/breccias, and late carbonate and/or sulphate open space infill. Magmatic fluids are interpreted to have utilised the same plumbing system as the late stage feldspar porphyry intrusive, and then migrated into the Roamane Fault which was dilated by; dextral rotation on elements of the transfer structure, normal faulting, and refraction around the competent footwall hornblende diorite. Bonanza gold is localised in a jog in the Roamane Fault, hangingwall splits and at intersections with cross structures. Bulk low grade Stage I gold has been deposited by the mixing of magmatic fluids with cool gas condensate waters, whereas high grade Stage II gold mineralisation resulted from the rapid quenching of mineralised magmatic fluids by oxygenated groundwaters.

Jan 1, 1995

By Wang QP, Quan YH

Mechanical models are established in accordance with the degree of mining on both sides of the coal pillar, and formulae were derived which calculated the superposition stress distribution and the width of the plastic region. The stability of the coal pillar was analysed and a reasonable size of coal pillar determined, in accordance with the elastic region rate. Further practical examples for the stability of the coal pillar are calculated and simulated.

Jan 1, 1992

By Crellin D, Reed SM

The paper presents details of borehole instrumentation schemes for the purposes of monitoring rock and fill deformations associated with groundwater in underground and surface coal mines. The instruments are described which measure rock mass displacements, permeability changes and alterations to hydrology. Methods of installation are detailed and the applicability of instruments discussed. Reduction and interpretation of results are detailed.

Jan 1, 1988

In June 1992, the High Court of Australia recognised native title of the Meriam people over parts of the Mer Island in the Torres Strait as a form of common law. The Court also indicated that native title may have survived European settlement of the mainland Australia where it had not been extinguished by Governments and Aboriginal people have maintained their traditional connection with the land. The decision meant that two systems of land law were seen as existing side by side in Australia: ò one which derived from grants from the Crown under laws passed by Parliament; ò another which derived from the diverse laws and customs of the many Aboriginal groups in Australia.

Jan 1, 1996

By Zenari L, Kent D

As our mines introduce more sophisticated production technology into their operations, the dependence on communication systems is markedly increased to allow the management of the technology. However the attention given to the communication systems has lagged that given the production equipment - namely LHDs, trucks and jumbos. At times it was treated as after thought. However, this is changing as the degree of automation increases in our mines. The communication system is now being given much more priority and is genuinely becoming a part of the mine design. The transfer of information around underground, as well as between the surface and underground, is an essential day-to-day activity, with the aim being a smoothly run operation. However the mine environment is far from static, and situations arise - such as breakdowns or other incidents - that require swift analysis of the issue, its cause and its remedy. Also, as communication systems become more sophisticated their use in areas, other than direct data flow, become available. The importance of communication, its development, and new areas being impacted by communication is the subject of this Paper.

Jan 1, 1997

By J H. Baker, P G. Beadle, J P. O&apos, Brien

In 1974 a preliminary study of the refractories industry in theRepublic of Indonesia was completed by Crown Lynn Consultants, a subsidiary of Cerarnco Ltd., on behalf of the Indonesian and New Zealand Governments. As a result of recommendations arising from that study the two Governments commissioned, in 1976, as a Bilateral Assistance project, an investigation into the potential of the refractories industry in Indonesia. Ceramco Ltd., was retained to carry out the study on behalf of the New Zealand Government. The Directorate-General of Chemical Industries, Directorate of Silicate Industries administered the project on behalf of the Indonesian Government. Indonesian counterparts to the New Zealand study team were provided by the Directorate of Silicate Industries.

Jan 1, 1978

By Culshaw MG, Deaves AP, Bell FG

The accurate prediction both of the water ingress into sub-surface excavations and the nearby groundwater pressures is of fundamental importance to the control of the stability and flooding of tunnels or mines constructed below the water table. Predic- tions are usually based on laboratory and in situ permeability determinations together with observations of groundwater conditions in boreholes. Although established theoretical methods provide a basis for prediction, the actual ingress depends on many factors. The objective of this paper is to explore the geological controls on groundwater conditions, and the available methods of prediction of both groundwater flow and pressure are outlined. Salient points are emphasised by reference to a case history involving the construc- tion of a tunnel in a faulted and mixed sequence of sandstones, siltstones, shales and coals. Water ingress quantities have been monitored for a variety geological and geotechnical conditions including heavily faulted and mine disturbed ground. The overall results are discussed with reference to the relevant hydrological and geologi- cal conditions in terms of the geological structure, lithology and rockmass condition as well as the construction methods.

Jan 1, 1988

By Russo S

Metals Refining Operations Pty Ltd (MRO) began refining gold in PNG in 1991 and has undergone continuing growth since then in servicing an everchanging and growing market. MRO's ownership combines PNG Government interests and Golden West Refining Corporation Limited as operator.Features include a very diverse range of suppliers, a full range of technical methods and challenges and the financing and marketing responses unique to a developing country. These areas are examined and documented with special emphasis upon the service needs for the gold industry and future trends and challenges are discussed.

Jan 1, 1997

EQUIPMENT TO BE DISCUSSED It is the intention of this paper to discuss the transporting of large skid mounted equipment and track machines around open cut mines. By large I mean 100 to 350 tonne capacity being trans- ported on minesite lowloaders and the capability of moving loads of 300 to 1200 tonne by other means. It is also possible to move larger loads. The main factor in transporting large loads is eco- nomics and is a balance between the cost of the transporter and the increased production from the equipment being moved. For example it could be possible to shift a 7000 tonne dragline faster than their own means of propulsion, being the "walking feet" method. However for the cost of $10 to $12,000,000.00 or more you can afford to walk the dragline and suffer the production loss. Let us concentrate on the economically realistic. BOSICH FBT MINESITE LOWLOADERS 100 TO 350 TONNE CAPACITY. Why initially consider having such a transporter? Our experience has shown that initial enquiries evolve from mines requiring to move large drills, 50 to 200 tonne weight and large hydraulic excavators or backhoes which are track mounted. The reason for shifting them is to move equipment from a mining face to enable blasting, to remove to the central workshop for repairs, overhauls and routine maintenance, to transport equip- ment from one mine face to another, and for drills, to move from one drilling pattern to the next. The cost in terms of time lost and extra wear on tracked equip- ment easily justifies the cost of the transporter. The tracks on large drills and shovels are not intended for long distance walk- ing. These tracks are designed to move the machines to position for drill holes, or moving around the mine face. Long distance travel, ie generally 1 km or more, results in overheating of track rollers, track drive components and accelerated wear on tracks.

Jan 1, 1989

By Blom MS

Two well-developed styles of mineralization occur in the Nevados del Famatina mining district, Famatina ranges, La Rioja province, Argentina. Porphyry molybdenum- copper-gold mineralization and high level acid sulphate alteration/mineralization (Nevados del Famatina) are related to intrusion of the Pliocene Mogote rhyodacite porphyry complex. High sulphidation epithermal mineralization (La Mejicana) is developed peripheral to the Nevados del Famatina deposit. Both are hosted mainly by the Ordovician Negro Peinado metapelites.At Nevados del Famatina, five mineralized fracture events have been identified and correlated with four distinct alteration assemblages. Stage I (barren quartz) and stage II (molybdenite¦sphalerite¦pyrite) mineralization are associated with a K-silicate alteration assemblage of K-feldspar+biotite+quartz+magneti te¦ilmenite¦anhydrite. Stage III (bornite+pyrite+sphalerite+molybdenite ¦chalcopyrite¦idaite) and stage IV (chalcopyrite+pyrite +sphalerite+gold¦tennantite-tetrahedrite) mineralization are related to a quartz-sericite assemblage of quartz +phengite+illite+pyrite+rutile. Stage V mineralization is divided into two substages. Stage Va (chalcopyrite +pyrite+sphalerite¦ tennantite-tetrahedrite ¦ tellurides ¦ gold ¦enargite¦famatinite¦stibnite¦molybdenite) is related to a sericite-clay assemblage of quartz+illite+kaolinite ¦montmorillonite¦alunite. Alunite-kaolinite alteration (alunite+pyrophyllite+kaolinite+ aluminum - phosphate -sulphate minerals ¦illite¦fluorite¦corundum¦anhydrite) occurs in the upper part of Nevados del Famatina associated with the later stage Vb (quartz+famatinite +chalcopyrite+covellite + chalcocite ¦ marcasite ¦ enargite ¦ luzonite¦sphalerite¦melnikovite) mineralization.

Jan 1, 1990

By S Lee, I Sohn

The ferrous and non-ferrous metallurgical industries have been utilising slags, fluxes and mattes for process optimisation and quality improvements at high temperatures. Understanding the fundamentals of the thermodynamics and kinetics of chemical metallurgy regarding slags, fluxes and mattes has been essential to the technological developments of these optimisation and improvements. This work will discuss how these fundamentals have been studied in the reactions involved and implemented in the ferrous industry from primary refining to continuous casting. In particular, the chemical driving forces that allow these reactions to take place and the limitations of the kinetics that require optimisation to enhance the reactions. In addition, the future research direction for slag technology innovation and the role of these fundamentals will also be described.

Jun 19, 2024

By Deutsch G. P

The output of an underground mine often depends entirely on the mine winding system. -Decisions made--at the design stage affect the economy and operation'of the mine'.througb -its entire life. A modern mine winding installation is an integrated system and its design requires a multidisciplinary approach including expertise in the-materials handling, mining, mechanical, civil, structural, electrical and control engineering fields. The paper-sets out the elements of typical mine wind- ing systems-and describes some of the more important decisions which must be made during the planning and design process, It is no longer.adequate to. base the choice of a system on the pre- ferences and experiences of individuals. Major Australian winding install- ations are usually designed on the basis of overseas experience and some of the detail design is often carried, out overseas. Differences in basic design criteria occur from country to

Jan 1, 1973

With the burgeoning opportunities for new gold mines to be developed the opportunity now exists for a reassessment of the optimal processing path for these gold ores. Projects have traditionally followed the path of whole ore cyanidation with either Carbon In Pulp (CIP), Carbon In Leach (CIL) or Merrill Crowe. The challenge ahead is whether these traditional processing methods are the best option for stakeholders, or to go beyond CIP and use a combination of currently available technologies that can be used to provide gold recovery at a significantly reduced capital cost and minimal deleterious impact on the environment. Either stand alone or combinations of gravity concentration and flotation, can produce a gold bearing concentrate that can then be fed directly to a batch or continuous intensive cyanidation unit. Treatment of a gravity/flotation concentrate by intensive cyanidation may be processed by the InLine Leach Reactor (ILR) developed by Gekko Systems of Australia. The advantages of the technology combining gravity/flotation followed by intensive cyanidation are significantly reduced capital costs; improved safety due to reduced cyanide inventories; the majority of tailings un-contaminated by cyanide; less energy required due to an opportunity for an increase in grind size û reducing green house gas emissions; detoxification of concentrate tailings can minimise tailings disposal and containment requirements.

Jan 1, 2004

In early-1989, subsidence due to voids at the top of previously filled stopes and stopes awaiting filling,began to threaten the 15 level fill conveyor horizon. This together with the need to maintain production targets meant that a method was required to significantly increase fill placement.Alternative methods of placing dry fill underground were investigated. One option was to drill 200 mm boreholes from surface directly into stopes 600 - 800 metres underground. A drilling program was successfully undertaken, and resulted in the placement of more than 800 000 tonnes of dry aggregate fill via four boreholes.This paper details the drilling program undertaken and discusses the difficulties encountered, the fill placement system and the project costs.

Jan 1, 1992